1000 - 2500 Watts VS Series Special Features VS1-B2-H522-00 1100W total • Power factor correction • IEC 555-2 harmonic distortion compliance • CISPR 22, EN55022 Level B conducted / radiated EMI • EN61000 immunity standards • European CE Mark • Current share on all outputs • Remote sense on all outputs • Overload protection on all outputs • Voltage adjustment on all outputs • Margining on all outputs • AC-OK-signal (logics “1” or “0”) • Global DC OK (logics “1” or “0”) VS3-D2-C2-20 1200W total • DC-OK signal and status indicator LED-on all outputs • Global and individual module inhibits/enable • 3 year warranty • 2500 W with 3-phase input VS6-L2-00 1500W total Environmental Operating temperature: -10°C to 50°C (derate each output linearly to 60% at 70°C) 40°C max. for reverse air (option #1) Shock/Vibration: Mil-Hdbk 810E Humidity: 95% non-condensing VS8-L9-D9-20 Storage temperature: -55°C to +85°C 2500W total (case limit) Temperature coefficient: 0.02% per °C Cooling: Internal DC fan 24V Safety VS4/9 UL UL60950-1 E133211 2000 - 2500 W CSA CSA C22.2 No. 60950-1-03 VDE EN60950 CB Certificate and report CE Mark 1 Technical Support: (888) 41-ASTEC or (407) 241-2752 69-825-410 Rev C Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 12.01.04 VS Series ASIA EUROPE AMERICAS Units 2111-2116, Level 21 Astec House, Waterfront Business Park 5810 Van Allen Way Tower1, Metroplaza Merry Hill, Dudley Carlsbad, CA 92008 223, Hing Fong Road West Midlands, DY5 1LX, UK Telephone: 760-930-4600 Fwai Fong, New Territories Telephone: 44 (1384) 842-211 Facsimile: 760-930-0698 Hong Kong Facsimile: 44 (1384) 843-355 Telephone: 852-2437-9662 Facsimile: 852-2402-4426 Electrical Specs Output Input Adjustment range ±10% minimum Fuse rating 600 V / 25 A (internal)1Ø 250 V / 20 A (internal)3Ø Margining ±4-6% nominal Input voltage 85-264 VAC 1Ø Line/load reg 0.2% or 5 mV max. VS1, VS3 & VS4 Ripple RMS: 0.1% or 10 mV (See operating curve) P-P: 1.0% or 50 mV 180-264 VAC 3Ø Bandwidth limited to 20 MHz VS6, VS8 & VS9 Dynamic response 2% or 100 mV with 25% load step Frequency 47 to 440 Hz (any output) Inrush current 40 A peak max. Recovery time To within 1% in <300 µsec Efficiency 75% - 82% Overvoltage protection 2-5 V 122% to 134% of output voltage; Power factor 0.99 typical 12-48 V 110% to 120%; recycle AC (0.9 on VS6, VS8 & VS9) Overload protection Main: 105% to 120% of rated current Turn-on time AC / 1 sec; Auxiliaries:105% to 140% Inhibit / 100 ms max. Short circuit protection Protected for continuous short circuit, EMI-filter CISPR 22, EN55022 Level B recovery automatic conducted/radiated Reverse voltage Leakage current 2 mA max. at 240 VAC protection 100% of rated output current Holdover storage 20 ms min. / 40 ms typical Thermal protection Each module thermally protected. independent of VAC Input module: auto recovery. Output modules; recycle AC. AC-OK warning time >5 ms (power fail) Remote sense Up to 0.5 V - total drop Loss of phase On VS6, VS8 & VS9, unit will continue to operate with loss Single wire parallel Current share to 2% of total rated of phase current Input Operating Curve Switching frequency 200 KHz 2200 (900-1500 W module, 400 KHz) DC OK -2% to -6% of nominal 2000 Output/Output isolation >1 Megohm 1800 1600 1400 1200 1000 800 600 400 200 0 INPUT AC VOLTAGE (VAC) @ 50/60Hz Single Phase www.astecpower.com 2 69-825-410 Rev C 12.01.04 MAXIMUM OUTPUT POWER (W) 80 100 120 140 160 180 200 220 240 260 SLOT 1 SLOT 1 SLOT 1 SLOT 2 SLOT 2 SLOT 2 SLOT 3 SLOT 3 SLOT 4 SLOT 4 SLOT 5 SLOT 6 Common Examples and Specifications Case size 1 = 5 inch, 2 slot, 1500 W max 1Ø Option Codes 3 = 8 inch, 4 slot, 2000 W max 1Ø 0 = no options 4 = 11 inch, 6 slot, 2000 W max 1Ø 1 = rear air exhaust (40°C max.) 6 = 5 inch, 2 slot, 1500 W max 3Ø 3 = set unit for global enable 8 = 8 inch, 4 slot, 2500 W max 3Ø 5 = options 1 & 3 9 = 11 inch, 6 slot, 2500 W max 3Ø USE ONLY-FOR MODIFIED STANDARD, (Same for Each Slot) CONSULT-FACTORY Indicates CE compliance Output Module Code Output Voltage Code Configuration Rules Parallel Code 1. Omit digits that do not apply. A = 300 W single 1 slot 0= 2V VS1 and VS6 2. a. Specify modules from lowest number B = 600 W single 1 slot 1= 3.3 V available slots of outputs to highest. C = 900 W single 2 slots 2= 5 V J1 b. If number of outputs are equal, specify D = 1200 W single 2 slots 3= 12 V from highest to lowest power increments. VS3 and VS8 E = 250 W dual 1 slot 4= 15 V c. If power increments are equal, specify available slots N F = 250 W triple 1 slot 5= 24 V from highest to lowest current. G = 500 W dual 1 slot 6= 28 V 3. All model configurations created using J1 VS4 and VS9 H = 500 W triple 1 slot 7= 36 V this selection guide represent standard available slots products with standard availability and K = 750 W single 1 slot 8= special voltage N lead times. L = 1500 W single 2 slot (consult factory) Parallel Codes 4. If slots are left empty, a blank panel will J1 9= 48 V be automatically installed. 0 = no parallel 1 = 1 & 2 2 = 2 & 3 Example (more on next page): VS 1 - K 2 -G 33-00 - CE 3 = 3 & 4 4 = 1 & 2 & 3 5 inch case No options (2 slots available) 5 = 2 & 3 & 4 Slot 1 Slot 2 No paralleling 6 = 1 & 2 + 3 & 4 1: 5V @ 150A 2: 12V @ 21A 3: 12V @ 20A 7 = 1 & 2 & 3 & 4 8 = 3 & 4 + 5 & 6 9 = 1 & 2 + 3 & 4 + 5 & 6 Output Current Output Voltage Module Identification Identification Output Output A (1 slot) B (1 slot) C (2 slots) D (2 slots) E, F (1 slot) G, H (1 slot) K (1 slot) L (2 slots) Voltage Voltage 300 W 600 W 900 W 1200 W 250 W Multi 500 W Multi 750 W 1500 W Code Single Single Single Single Main Output Main Output Single Single 0 2 V 60 A 120 A 180 A 240 A 25 A 50 A 150 A 300 A 1 3.3 V 60 A 120 A 180 A 240 A 25 A 50 A 150 A 300 A 2 5 V 60 A 120 A 180 A 240 A 25 A 50 A 150 A 300 A 3 12 V 25 A 50 A 75 A 100 A 10.5 A 21 A 62.5 A 125 A 4 15 V 20 A 40 A 60 A 80 A 8.3 A 16.6 A 50 A 100 A 5 24 V 12.5 A 25 A 37.5 A 50 A 5.3 A 10.5 A 31.2 A 62.4 A 6 28 V 10.7 A 21.4 A 32.1 A 42.8 A 4.5 A 9 A 26.7 A 53.4 A 7 36 V 8.3 A 16.6 A 24.9 A 33.2 A N/A N/A 20.8 A 41.6 A 9 48 V 6.3 A 12.5 A 18.75 A 25 A N/A N/A 15.6 A 31.2 A Note: Increments of current not shown can be achieved by paralleling modules (add currents of each module selected). Auxiliary Output Table: Output(s) 2 and/or 3 of Module Voltage Module Identification Identification Output Output E F G H Voltage Voltage 250 W Dual 250 W Triple 500 W Dual 500 W Triple Code Aux. Output Aux. Output Aux. Output Aux. Output 0 2 V 10 A 5 A 20 A 10 A 1 3.3 V 10 A 5 A 20 A 10 A 2 5 V 10 A 5 A 20 A 10 A 3 12 V 10 A 5 A 20 A 10 A 4 15 V 10 A 5 A 20 A 10 A 5 24 V 5 A 2.5 A 10 A 5 A 6 28 V 5 A 2.5 A 10 A 5 A 3 Technical Support: (888) 41-ASTEC or (407) 241-2752 69-825-410 Rev C Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 12.01.04 VS Series ASIA EUROPE AMERICAS Units 2111-2116, Level 21 Astec House, Waterfront Business Park 5810 Van Allen Way Tower1, Metroplaza Merry Hill, Dudley Carlsbad, CA 92008 223, Hing Fong Road West Midlands, DY5 1LX, UK Telephone: 760-930-4600 Fwai Fong, New Territories Telephone: 44 (1384) 842-211 Facsimile: 760-930-0698 Hong Kong Facsimile: 44 (1384) 843-355 Telephone: 852-2437-9662 Facsimile: 852-2402-4426 EXAMPLES Examples of Model Numbers - SINGLE OUTPUTS Voltage Other Voltages Total Volts / Size Model Power Amps (H x W x L) Number Available ID Code 600 W 5 V / 120 A 5 x 5 x 11 VS1-B2-00 2 V 0 750 W 12 V / 62.5 A 5 x 5 x 11 VS1-K3-00 3.3 V 1 900 W 5 V / 180 A 5 x 5 x 11 VS1-C2-00 5 V 2 12 V 3 1200 W 5 V / 240 A 5 x 5 x 11 VS1-D2-00 15 V 4 1200 W 2 V / 600 A 5 x 8 x 11 VS3-L0-L0-20 24 V 5 1500 W 15 V / 100 A 5 x 5 x 11 VS1-L4-00 28 V 6 2000 W 5 V / 400 A 5 x 8 x 11 VS3-D2-C2-20* 36 V 7 2500 W 48 V / 52 A 5 x 8 x 11 VS8-L9-D9-20 ** Special 8 (consult factory) 48 V 9 * D2 module derated to 1100 W (2000 W max.) **D9 module derated to 1000 W (2500 W max ) Examples of Model Numbers - MULTIPLE OUTPUTS Total Output Output Output Output Output Output Size Model Number Power 1 2 3 4 5 6 500 W 5 / 50 12 / 10 12 / 10 5 x 5 x 11 VS1-H233-00 750 W 5 / 50 12 / 10 12 / 10 15 / 8.3 15 / 5 5 / 5 5 x 5 x 11 VS1-H233-F442-00 800 W 5 / 60 12 / 21 12 / 10 5 / 10 5 x 5 x 11 VS1-A2-H332-00 800 W 5 / 60 12 / 21 12 / 10 24 / 5 5 x 5 x 11 VS1-A2-H335-00 800 W 5 / 60 15 / 16.6 15 / 10 5 / 10 5 x 5 x 11 VS1-A2-H442-00 800 W 5 / 60 15 / 16.6 15 / 10 24 / 5 5 x 5 x 11 VS1-A2-H445-00 990 W 5 / 150 2 / 120 5 x 5 x 11 VS1-K2-B0-00 1000 W 5 / 50 12 / 10 12 / 10 15 / 16.6 15 / 10 24 / 5 5 x 5 x 11 VS1-H233-H445-00 1000 W 5 / 50 12 / 10 12 / 10 15 / 16.6 5 / 10 24 / 5 5 x 5 x 11 VS1-H233-H425-00 1100 W 5 / 120 12 / 21 12 / 20 5 x 5 x 11 VS1-B2-G33-00 1100 W 5 / 120 12 / 21 12 / 10 5 / 10 5 x 5 x 11 VS1-B2-H332-00 1100 W 5 / 170 12 / 10 12 / 10 5 x 5 x 11 VS1-B2-H233-10 1100 W 5 / 120 15 / 16.6 15 / 10 5 / 10 5 x 5 x 11 VS1-B2-H442-00 1100 W 5 / 120 15 / 16.6 15 / 10 24 / 5 5 x 5 x 11 VS1-B2-H445-00 1400 W 5 / 180 12 / 21 12 / 20 5 x 8 x 11 VS3-C2-G33-00 1400 W 5 / 180 12 / 21 12 / 10 5 / 10 5 x 8 x 11 VS3-C2-H332-00 1440 W 5 / 240 2 / 120 5 x 8 x 11 VS3-D2-B0-00 1600 W 5 / 170 12 / 20 12 / 21 5 / 20 5 x 8 x 11 VS3-B2-G23-G32-10 1680 W 5 / 240 2 / 240 5 x 8 x 11 VS3-D2-D0-00 1700 W 5 / 240 12 / 21 12 / 20 5 x 8 x 11 VS3-D2-G33-00 1900 W 5 / 180 12 / 21 12 / 20 5 / 50 15 / 10 24 / 5 5 x 8 x 11 VS3-C2-G33-H245-00 2000 W 5 / 300 12 / 21 12 / 10 5 / 10 5 x 8 x 11 VS3-L2-H332-00 2000 W 5 / 240 12 / 21 12 / 20 5 / 60 15 / 10 24 / 5 5 x 8 x 11 VS3-D2-G33-H245-00 2500 W 5 / 300 3.3 / 120 12 / 21 12 / 10 15 / 10 5 x 8 x 11 VS8-L2-B1-H334-00 Notes: Pin Assignments Electrical Characteristics Single Output PFC 1. DC OK minus 2 to 6% of nominal output voltage J1 CONTROL CONNECTOR J1 CONTROL CONNECTOR (tracking). Pin No. Function Pin No. Function J1-1 AC OK Logic 1 J1-1 +Remote Sense 2. Inhibit & Enable are both TTL compatible. J1-2 AC OK Logic 0 J1-2 Remote Margin / V. Program ISOLATED requires 2 mA source, typical. J1-3 Global DC OK/Conv Run Logic 1 J1-3 Remote Margin Hi J1-4 Global DC OK/Conv Run Logic 0 J1-4 -Remote Sense / Margin Lo 3. DC OK/Converter Run denotes output voltage J1-5 Global DC OK/Conv Run/AC OK J1-5 DC OK / Conv Run Logic 1 is present and converters are running Return J1-6 Isolated Inhibit (Or'ed signal configuration). J1-6 Global Inhibit Logic 0*/ENA Logic '0' J1-7 DC OK / Conv Run / ISO Inh. J1-7 Global Inhibit Logic 1*/ENA Logic '1' Return 4. PFC LED: Red = Bulk DC bus voltage low; J1-8 Single Wire Parallel J1-8 Global Inhibit Return*ENA RTN Green = Bulk DC OK. J1-9 Spare Pin J1-9 Global Isolated Inhibit J1-10 Spare Pin J1-10 Global Isolated Inhibit Return 5. Output LED: Red = Indicated output not operating within tolerance; * Changes to Enable with Option Code 3 Green = Indicated output operating within tolerance. Multiple Output J2 CONTROL CONNECTOR J1 CONTROL CONNECTOR Pin No. Function 6. The 5 x 5 x 11 (VS1/6) case is power limited to Pin No. Function J2-1 V2 +Remote Sense 1500W max. See operating curve. J1-1 V1 +Remote Sense J2-2 V2 Remote Margin / V. Program J1-2 V1 Remote Margin / V. Program J2-3 V2 Remote Margin Hi 7. The 5 x 8 x 11 case and 5 x 11 x 11 case (VS3/4) J1-3 V1 Remote Margin Hi J2-4 V2 -Remote Sense / Margin Lo are power limited to 2000W max. The VS8/9 J1-4 V1 -Remote Sense / Margin Lo J2-5 V2 DC OK /Logic 1 cases are power limited to 2500W max. J1-5 V1 DC OK / Conv Run Logic 1 J2-6 V3 +Remote Sense J1-6* V1 Isolated Inhibit J2-7 V3 Remote Margin / V. Program 8. Specifications subject to change without J1-7 V1 DC OK / Conv Run / ISO Inh. J2-8 V3 Remote Margin Hi notice. Return J2-9 V3 -Remote Sense J1-8 V1 Single Wire Parallel J2-10 V3 DC Good /Logic 1 9. Warranty: 3 yrs J1-9 V2 Single Wire Parallel J1-10 V3 Single Wire Parallel * Inhibits off all the outputs within that module. www.astecpower.com 69-825-410 Rev C 4 12.01.04 SLOT 1 SLOT 2 SLOT 1 SLOT 2 Drawings VS1 & VS6 • 1000-1500 WATTS 5-inch Case Size (5” x 5” x 11”) .94 11.00 ± .05 1.2 MAX VS1 (279.31 ± 1.27) 23.89) 8-32 UNC-2B Threaded Insert, 4 Places Input 5.00 ± 0.05 Like Pattern Opposite Side Module STD AIR FLOW Max penetration: 0.150 (3.81 ) AC High Neutral Ground 5.00 Max (127.03) Side 4.000 ± .020 (101.60 ± .50) J1 2.04 ± .05 (51.82 ± 1.27) 3.49 ± .05 .500 ± .050 (88.65 ± 1.27) (12.70 ± 1.27) 6.750 ± .020 .750 ± .050 AC Main Input (171.45 ± .50) (19.05 ± 1.27) .27 ± .05 (6.86 ± 1.27) 8-32 UNC-2B Bottom Threaded Insert, VS6 4 Places Input 5.00 ± 0.05 Max penetration: Module 0.150 (3.81) AC Phase A AC Phase B AC Phase C 5.00 Max AC Ground 6.750 ± .020 (127.03) N (171.45 ± .50) Back J1 2.04 ± .05 (51.82 ± 1.27) 3.49 ± .05 (88.65 ± 1.27) .750 ± .050 .500 ± .050 4.000 ± .020 (19.05 ± 1.27) (12.70 ± 1.27) (101.60 ± .50) NOTES (ALL MODELS) 1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). For VS1, VS3 & VS4 additional GND CONN added for VS6, VS8 & VS9. Max torque: 10 in-lbs (1.1 N-m). 2. Control connectors: (J1 and J2) 10 position Molex 90130-3210 housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. 3. Output terminals (A-300 W) (B-600 W) & (K-750 W) single modules: two (2) 10-32 UNF HEX HD BOLTS. Max. torque: 25 in-lbs (2.78 N-m). 4. Output terminals (E/F-250 W) & (G/H-500 W) dual/triple modules: Primary: two (2) 10-32 UNF HEX HD BOLTS. Max. torque: 25 in-lbs (2.78 N-m). Secondary: barrier strip two (2) 6-32 UNC screws (0.375” centers) per output. Max torque: 10 in-lbs (1.1 N-m). 5. Output terminals (C-900 W) (D-1200 W) & (L-1500 W) single modules: four 5/16-18 x 5/8" hex head cap screws. Max. torque: 120 in-lbs (13.35 N-m). Captive lock washer provided. 6. Chassis material: aluminum with chemical film coating. 7. Adjustment access: voltage, power fail, and overcurrent from front panel. 8. Bar code: code 39 extended. 9. Mounting for 5-inch & 8-inch case: four(4) 8-32 clinch nuts on three (3) surfaces. Mounting for 11-inch case: four (4) 8-32 clinch nuts on two (2) side surfaces & six (6) 8-32 clinch nuts on bottom surface. Max. penetration 0.150 inch (3.81). Max. torque: 15 in-lbs (1.67 N-m). 10. Additional support is recommended when unit is mounted in a suspended configuration. Mounting clinch nuts are not designed to support the weight of the unit. 11. Fans: 5-inch case, (1) 4.5" dia, 112 CFM (no load), 49 dBA. 8-inch case, (1) 4.5" dia, 112 CFM (no load), 49 dBA; (2) 2.25” dia, 23 CFM (no load), 38 dBA. 11-inch case, (2) 4.5" dia, 112 CFM (no load), 49dBA 12. All dimensions are in inches (mm). 13. Specifications subject to change without notice. 5 Technical Support: (888) 41-ASTEC or (407) 241-2752 69-825-410 Rev C Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 12.01.04 VS Series SLOT 1 SLOT 2 SLOT 3 SLOT 4 SLOT 1 SLOT 2 SLOT 3 SLOT 4 ASIA EUROPE AMERICAS Units 2111-2116, Level 21 Astec House, Waterfront Business Park 5810 Van Allen Way Tower1, Metroplaza Merry Hill, Dudley Carlsbad, CA 92008 223, Hing Fong Road West Midlands, DY5 1LX, UK Telephone: 760-930-4600 Fwai Fong, New Territories Telephone: 44 (1384) 842-211 Facsimile: 760-930-0698 Hong Kong Facsimile: 44 (1384) 843-355 Telephone: 852-2437-9662 Facsimile: 852-2402-4426 8-inch Case Size (5” x 8” x 11”) DRAWINGS • VS3 & VS8 • 1000-2500 WATTS (18 lbs. / 8.2 kg. maximum) VS3 .94 11.00 ± .05 1.2 Input MAX 7.90 ± 0.05 (279.31 ± 1.27) 23.89) 8-32 UNC-2B Module (200.66 ± 1.27) Threaded Insert, 4 Plac Like Pattern Opposite S STD AIR FLOW Max penetration: 0.150 AC High Neutral Ground 5.00 MAX (127.03) Side 4.000 ± .020 (101.60 ± .50) J1 2.04 ± .05 (51.82 ± 1.27) 3.49 ± .10 (88.65 ± 2.54) 4.94 ± .10 .500 ± .050 (125.48 ± 2.54) (12.70 ± 1.27) 6.39 ± .10 6.750 ± .020 .750 ± .050 (162.31 ± 2.54) (171.45 ± .50) (19.05 ± 1.27) .27 ± .05 (6.86 ± 1.27) AC Main Input Bottom Back VS8 7.90 ± 0.05 (200.66 ± 1.27) 1.2 AC Phase A 6.750 ± .020 AC Phase B 8-32 UNC-2B (171.450 ± .50) AC Phase C Threaded 5.00 Insert, 4 Places MAX AC Ground (127.03) Max penetration: N 0.150 (3.81) Input .750 ± .050 (19.05 ± 1.27) Module J1 2.04 ± .05 (51.82 ± 1.27) 3.49 ± .10 1.067 ± .050 (88.65 ± 2.54) (27.099 ± 1.270) 4.94 ± .10 5.750 ± .020 (125.48 ± 2.54) (146.050 ± .508) 6.39 ± .10 (162.31 ± 2.54) www.astecpower.com 6 69-825-410 Rev C 12.01.04 Drawings VS4 & VS9 • 2000-2500 WATTS 1.2 8-32 UNC-2B THREADED INSERT, 6 PL 11-inch Case Size (5” x 11” x 11”) VS4 10.80 ±.20 274.32 ±5.04 (PFC) AC HIGH ~ N NEUTRAL S S S S S S 6.750 ±.02 GROUND L L L L L L 171.450 ±.50 O O O O O O 5.00 MAX P/F 127.0 T T T T T T .52 13.1 6 1 6 5 4 3 2 1 .750 ±.05 19.050 ±1.270 J1 .33 8.3 2.04 ±.10 51.81 ±2.54 3.49 ±.10 1.067 ±.050 88.64 ±2.54 27.099 ±1.270 DETAIL A 4.94 ±.10 5.750 ±.020 125.47 ±2.54 146.050 ±.508 6.39 ±.10 8.750 ±.020 162.31 ±2.54 222.25 ±.508 7.84 ±.10 199.14 ±2.54 9.29 ±.10 235.97 ±2.54 VS9 10.80 ±.20 .94 11.00 ±.05 1.2 MAX 23.89 279.31 274.32 ±5.04 ±1.27 8-32 UNC-2B THREADED INSERT, 4 PL (PFC) LIKE PATTERN OPPOSITE SIDE AC Phase A AC HIGH ~ AC Phase B N NEUTRAL S S S S S S AC Phase C GROUND L L L L L L STD O O O O O O AIR FLOW 5.00 MAX P/F 127.0 FRONT AIR T T T T T T EXHAUST .52 13.1 6 1 6 5 4 3 2 1 ±.02 4.00 MAX 101.60 ±.50 OPTIONAL J1 REAR AIR EXHAUST .33 8.3 2.04 ±.10 51.81 ±2.54 3.49 ±.10 88.64 ±2.54 DETAIL A 4.94 ±.10 ±.05 .50 12.70 ±1.27 125.47 ±2.54 6.39 ±.10 162.31 ±2.54 6.75 +.02 .75 ±.05 - 171.45 +.50 19.05 - ±1.27 7.84 ±.10 199.14 ±2.54 .27 ±.05 9.29 ±.10 6.86 ±1.27 235.97 ±2.54 7 Technical Support: (888) 41-ASTEC or (407) 241-2752 69-825-410 Rev C Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 12.01.04 INTERNAL FUSE 25 AMPS/600V ~ INTERNAL FUSE 25 AMPS/600V ~ ASIA EUROPE AMERICAS Units 2111-2116, Level 21 Astec House, Waterfront Business Park 5810 Van Allen Way Tower1, Metroplaza Merry Hill, Dudley Carlsbad, CA 92008 223, Hing Fong Road West Midlands, DY5 1LX, UK Telephone: 760-930-4600 Fwai Fong, New Territories Telephone: 44 (1384) 842-211 Facsimile: 760-930-0698 Hong Kong Facsimile: 44 (1384) 843-355 Telephone: 852-2437-9662 Facsimile: 852-2402-4426 Module Front Panels www.astec.com 69-825-410 Rev C 153 12.01.04 .60 ?.050 .60 ?.050 PH ?1.27 15.24 ?1.27 15.24 PH 1.00 1.03 ?.050 ?.050 26.21 ?1.27 25.40 ?1.27 PH + + .66 ?.050 .66 ?.050 16.80 ?1.27 16.80 ?1.27 .52 + J1 - 13.1 1.38 ?.050 34.94 ?1.27 3.70 ?.050 + 94.16 ?1.27 - 3.70 ?.050 - 2.77 + 94.16 ?1.27 .52 .52 .52 70.3 - 2.31 ?.050 13.1 13.1 58.59 ?1.27 13.1 J1 J2 J1 1.79 .33 .33 DETAIL A 45.5 1.442 8.3 8.3 REF 1.442 1.442 2.874 REF REF REF BLANK (1 SLOT) 900W/1200W/1500W 250W/500W 300W/600W/750W SINGLE OUTPUT DUAL/TRIPLE OUTPUT SINGLE OUTPUT (2 SLOTS) (1 SLOT) (1 SLOT) MODULE CODES MODULE CODES MODULE CODES C = 900W E = 250W DUAL A = 300W D = 1200W F = 250W TRIPLE B = 600W L = 1500W G = 500W DUAL K = 750W H = 500W TRIPLE