ASTEC LPS121
Specifications
3.63VDC
@36A
Input (PS)
85V to 264V
Operating Temperature
-20 to 70C
Performance Characteristics
Single
Total Max Current
36A
Volume
5.000"x3.000"x1.290"
Features
- 5 V Standby output and 12V Fan output
- Active power factor correction
- Adjustable main output
- Built-in Class B EMI filter
- EN61000-3-2 compliant
- Overload protection
- Overvoltage protection
- Power fail and remote inhibit
- Remote sense
- Single wire current sharing
- Thermal overload protection
Datasheet
Extracted Text
Embedded Power for Business-Critical Continuity Rev. 5.09.06 LPS120 Series 1of 3 LPS120 Series RoHS 120 Watts Total Power: 80 - 130 Watts Input Voltage: 85 - 264 VAC # of Outputs: Single Electrical Specifications Input Special Features Input range 85 - 264 VAC ; 127 - 300VDC • Active power factor correction Frequency 47-440 Hz • 3" x 5" footprint Inrush current 40A max., cold start @ 25°C • Less than 1U high Efficiency 80% typical at full load • EN61000-3-2 compliant FCC Class B conducted; CISPR22 Class B conducted; EN55022 • Remote sense EMI/RFI Class B conducted; VDE0878PT3 Class B conducted • Power fail and remote inhibit Power factor 0.99 typical • Single wire current sharing Safety ground 0.5mA @ 50/60 Hz, 264 VAC input • Adjustable main output leakage current • Built-in Class B EMI filter • Overvoltage protection Output • Overload protection Maximum power 80W for convection ; 130W with 30CFM forced air • Thermal overload protection Adjustment range ±5% minimum on the main outputs • 5 V Standby output Fan output 12V @ 500mA - 5%, +7% and 12V Fan output Standby outputs 5V @ 500mA ±5% Hold-up time 20ms @ 125W load, 120VAC input Short circuit protection on all outputs. Case overload protect- Overload protection ed @ 120-135% above rating Overvoltage protection 20-35% above nominal output Remote sense Compensates for 0.5 V lead drop max. Will operate without remote sense connected. Reverse connection protected. Logical Control Power failure TTL logic signal goes high 100-500 msec after main output; it goes low at least 4 msec before loss of regulation Safety Remote inhibit Requires a contact closure to disable the outputs, except 5V TUV 60950 standby. UL 60950 Remote sense Compensates for 0.5 V lead drop min. Will operate without CSA 60950 remote sense connected. Reverse connection protected. NEMKO 60950 AUSTEL 60950 CB Certificate and report CE Mark (LVD) 1 SK2 2 LIVE SK1 NEUTRAL SK3 P1 EARTH Embedded Power for Business-Critical Continuity Rev. 5.09.06 LPS120 Series 2of 3 Mechanical Drawing Environmental Specifications 3.00 Operating temperature: (76.2) 0° to 50°C ambient derate each output as 2.5% per degree from 2.55 50° to 70°C. -20°C start up (64.8) Storage temperature: -40°C to +85°C 0.15" DIA. 4 places (4.0) Electromagnetic designed to meetEN61000-4; susceptibility: -2, -3, -4, -5, -6, -8, -11 Level 3 Operating; non-condensing Humidity: 10% to 95% RH IEC68-2-6 to the levels of Vibration: IEC721-3-2 >550,000 hours at full load and MTBF demonstrated 25°C ambient conditions 5.00 (127.0) 4.55 (115.6) V Adjust M3.5 (2 places) POT 1.29 (32.8) 1 5 6 10 SK3 0.20" (5) Embedded Power for Business-Critical Continuity Rev. 5.09.06 LPS120 Series Ordering Information 3of 3 Astec Power Maximum Load Maximum Load Ripple Model Output Minimum 2 with Convection with 300CFM Peak Load Regulation P/P Number Voltage Load 3 Cooling Forced Air (PARD) 5810 Van Allen Way Carlsbad, CA 92008 LPS121 3.3V 0A 21A 36A 29A ±2% 50mV USA LPS122 5V 0A 16A 26A 29A ±2% 50mV Telephone: +1 760 930 4600 LPS123 12V 0A 6.7A 10.8A 12.8A ±2% 120mV Facsimile: +1 760 930 0698 Technical Support: +1 888 41 ASTEC LPS124 15V 0A 5.3A 8.7A 10.0A ±2% 150mV or +1 407 241 2752 LPS125 24V 0A 3.4A 5.4A 6.3A ±2% 240mV Waterfront Business Park LPS128 48V 0A 1.7A 2.7A 3.2A ±2% 480mV Merry Hill, Dudley West Midlands, DY5 1LX 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. United Kingdom 2. At 25°C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. Telephone: +44 (0) 1384 842 211 3. Peak-to-peak with 20 MHz bandwidth and 10 μF (tantalum capacitor) in parallel with a 0.1 μF capacitor at rated Facsimile: +44 (0) 1384 843 355 line voltage and load ranges. Units 2111-2116, Level 21 Tower 1, Metroplaza Pin Assignments 223, Hing Fong Road Connector LPS120 Kwai Fong, New Territories Hong Kong SK1 Pin1 Neutral Telephone: +852 2437 9662 Pin3 Line Facsimile: +852 2402 4426 SK2 TB-1 COMMON For global contact, visit: TB-2 Main output www.astecpower.com SK3 Pin1 +V1 Remote sense technicalsupport@astec.com Pin2 -V1 Remote sense Pin3 +Remote inhibit While every precaution has been taken to ensure accuracy and completeness in this literature, Astec Pin4 -Remote inhibit Power assumes no responsibility, and disclaims Pin5 +Power fail all liability for damages resulting from use of this Pin6 Common information or for any errors or omissions. Pin7 SWP Printed in USA Pin8 +12V Pin9 12V common Pin10 +5V standby Mating Connectors Emerson Network Power. (SK1)AC Input: Molex 09-50-8031 (connector) 08-52-0113 (pins) The global leader in enabling business-critical continuity. (SK2)DC Output: Molex series 19141-0058/0063 Spade lug (SK3) Control Signals: AC Power Molex 90142-0010 (USA) PINS: 90119-2110 or Connectivity Amp: 87977-3 PINS: 87309-8 DC Power Astec Connector Kit # 70-841-020, includes all of the above. Embedded Power Inbound Power Notes: Integrated Cabinet Solutions 1. Specifications subject to change without notice. Outside Plant 2. All dimensions in inches (mm), tolerance is ±.02”. 3. mounting holes MH1, MH2, MH3 should be grounded for Precision Cooling EMI purpose Site Monitoring and Services 4. Mounting MH1 is safety ground connection 5. Specifications are for convection rating at factory settings EmersonNetworkPower. com at 115 VAC input 25 C deg unless otherwise stated. 6. This power supply requires mounting on metal standoffs 0.20” (5m) in height. 7. Warranty: 1 year Emerson Network Power and the Emerson Network Power logo are trademarks and 8. Weight: 0.71 lb. / 0.32 kg service marks of Emerson Electric Co. ©2006 Emerson Electric Co.
Frequently asked questions
How does Industrial Trading differ from its competitors?

Is there a warranty for the LPS121?

Which carrier will Industrial Trading use to ship my parts?

Can I buy parts from Industrial Trading if I am outside the USA?

Which payment methods does Industrial Trading accept?

Why buy from GID?

Quality
We are industry veterans who take pride in our work

Protection
Avoid the dangers of risky trading in the gray market

Access
Our network of suppliers is ready and at your disposal

Savings
Maintain legacy systems to prevent costly downtime

Speed
Time is of the essence, and we are respectful of yours
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods