Embedded Power for Business-Critical Continuity Rev. 11.02.11_29 LPS100-M Series 1 of 3 LPS100-M Series 150 Watts Total Power: 80 - 150 Watts Input Voltage: 90 - 264 Vac # of Outputs: Single Electrical Specifications Special Features Input • Medical and ITE safeties • Active power factor correction Input ra nge: 90 - 264 Vac; 120 - 300 Vdc • 2” x 4” footprint Frequency: 47-63 Hz • Less than 1U high Inrush current: 50 A max., cold start @ 25 °C • EN61000-3-2 compliant Efficiency: 88% typical at full load • Remote sense EMI/RFI: FCC Class B conducted; CISPR22 Class B conducted; • Power fail EN55022 Class B conducted; VDE0878PT3 Class B conducted • Adjustable main output • Built-in Class B EMI filter Safety ground 275 µA @ 50/60 Hz, 264 Vac input • Overvoltage protection leakage current: • Overload protection Output • Thermal overload protection Maximum power: 100 W for convection (80 W for LPS102-M); • Isolated12 V Fan output 150 W with 30 CFM forced air (120 W for LPS102-M) • LPX50 Enclosure kit available Adjustment range: ± 10% minimum on the main outputs • POE isolation on main output of LPS109-M Fan output: 12 V @ 1 A isolated, ± 10% Hold-up time: 10 ms @ 150 W load, 120 Vac input Overload protection: Short circuit protection on all outputs. Case overload protected @ 110-160% above rating Overvoltage protection: 15-35% above nominal output Logical Control Power failure: Open collector logic signal goes high 100-500 msec after main output; it goes low at least 6 msec before loss of regulation Remote sense: Compensates for 0.5 V lead drop min. Will operate without remote sense Safety connected. Reverse connection protected. • TUV 60950, 60601-1 • UL 60950, 60601-1 • cULus 60950, 60601-1 • CB Certificate & report • CE Mark (LVD) • CQC Mark Embedded Power for Business-Critical Continuity Rev. 11.02.11_29 LPS100-M Series Environmental Specifications 2 of 3 Operating temperature: 0° to 50 °C ambient derate each output as 2.5% per degree from 50° to 70 °C. -20 °C start up Storage temperature: -40 °C to +85 °C Electromagnetic Designed to meet EN61000-4; susceptibility: -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity: Operating; non-condensing 10% to 95% RH Vibration: IEC68-2-6 to the levels of IEC721-3-2 MTBF calculated: 534,000 hours at full load and 25 °C ambient conditions, 230 V input, Bellcore Mechanical Drawing VR1 Output Voltage Adjust Pot SK203 M1 M2 1 4 SK2 8 GND 1 4 SK5 1 SK1 1 3 3.73" Mounting Hole (94.7) Ø0.16"[4.0] 4 Places 4.00" Max. Screw Head (101.6) Diameter .22” (5.6) 0.197” (5.0) Minimum Standoff height 2.00" (50.8) 1.72" (43.8) 1.29" (33.0) 0.10” (2.5) Embedded Power for Business-Critical Continuity Rev. 11.02.11_29 LPS100-M Series Americas Ordering Information 3 of 3 5810 Van Allen Way Maximum Load Maximum Load Model Output Minimum Ripple 2 Carlsbad, CA 92008 with Convection with 30CFM Peak Load Regulation 3 Number Voltage Load P/P (PARD) USA Cooling Forced Air Telephone: +1 760 930 4600 LPS102-M 5 V 0 A 16 A 24 A 30 A ± 2% 50 mV Facsimile: +1 760 930 0698 LPS103-M 12 V 0 A 8.3 A 12.5 A 14 A ± 2% 120 mV LPS104-M 15 V 0 A 6.7 A 10 A 11 A ± 2% 150 mV Europe (UK) Waterfront Business Park LPS105-M 24 V 0 A 4.2 A 6.3 A 7 A ± 2% 240 mV Merry Hill, Dudley LPS108-M 48 V 0 A 2.1 A 3.1 A 3.5 A ± 2% 480 mV West Midlands, DY5 1LX United Kingdom LPS109-M 54 V 0 A 1.85 A 2.8 A 3.1 A ± 2% 540 mV Telephone: +44 (0) 1384 842 211 1. Peak current lasting < 30 seconds with a maximum 10% duty cycle. Facsimile: +44 (0) 1384 843 355 2 . At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. Asia (HK) 3 . Peak-to-peak with 20 mHz bandwidth and 10 µF (tantalum capacitor) in parallel with a 0.1 µF capacitor at rated line voltage 14/F, Lu Plaza and load ranges. 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone: +852 2176 3333 Facsimile: +852 2176 3888 Mating Connectors Pin Assignments AC Input (SK1): Molex P/N: 09-50-3031, Pins: 08-52-0072 Connector LPS100-M For global contact, visit: or SK1 Pin 1 Neutral Landwin P/N: 3060S0302, Pins: 3360T011P www.Emerson.com/EmbeddedPower Pin 3 Line AC Ground Molex: 01-90020001 SK2 Pin 1 Common techsupport.embeddedpower DC Output Molex P/N: 09-50-3081, Pins: 08-52-0072 Pin 2 Common @emerson.com (SK2): or Pin 3 Common Landwin P/N: 3060S0802, Pins: 3360T011P Pin 4 Common While every precaution has been taken to ensure Remote Sense Molex P/N: 35155-0400, Pins: 08-70-0057 accuracy and completeness in this literature, Emerson Pin 5 +Vout (SK203): or Network Power assumes no responsibility, and disclaims Pin 6 +Vout Landwin P/N: 2640S04A0, Pins: 2543T011P all liability for damages resulting from use of this information or for any errors or omissions. Pin 7 +Vout Fan: (SK5): Molex P/N: 22-01-1042, Pins: 08-70-0049 Pin 8 +Vout or Landwin: P/N: 2510S04A0, Pins: 2543T011P SK203 Pin 1 Common Emerson Network Power. Emerson Network Power Connector Kit #70-841-025, includes all of the Pin 2 Power Fail The global leader in enabling above Pin 3 - Remote Sense business-critical continuity. Pin 4 + Remote Sense SK5 Pin 1 +12 V Fan AC Power Pin 2 +12 V Fan Pin 3 Fan Return (Isolated) Connectivity Pin 4 Fan Return (Isolated) DC Power Embedded Computing Notes: Embedded Power 1. Specifications subject to change without notice. Monitoring 2. All dimensions in inches (mm), tolerance is ±.02”. 3. mounting holes MH1, MH2 should be grounded for EMI Outside Plant purpose 4. Mounting MH1 is safety ground connection Power Switching & Controls 5. Specifications are for convection rating at factory settings Precision Cooling at 115 Vac input 25 °C unless otherwise stated. 6. This power supply requires mounting on metal standoffs Racks & Integrated Cabinets 0.20” (5 m) in height. Services 7. For DC input an external DC safety rated fuse must be used. 8. Warranty: 2 year Surge Protection 9. Weight: 0.44 lb. / 0.20 kg EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2011 Emerson Electric Co.