process yellow 116 1375 1797 375 3405 313 2985 240 Embedded Power for Business-Critical Continuity 242 2607 Rev.12.12.08_102 NLP65 Series 652 1 of 4 NLP65 Series Single, dual, and triple output Total Power: 65 - 75W Input Voltage: 85 - 264 Vac 120 - 370 Vdc* # of Outputs: Single, dual, triple Electrical Specifications Special Features Input • Universal Input Input voltage range: Universal input 85-264 Vac • 3” x 5” footprint (see Note 2) • Low profile fits 1U applications NLP65-76xx version only 120-370 Vdc • EN61000-3-2 compliance Input frequency range: 47-63 Hz option (HCC) Input current: 120 Vac 17 A max. • Overvoltage and short circuit (cold start) 230 Vac 32 A max protection • 65 W with free air convection Safety ground 120 Vac, 60 Hz 0.7 mA cooling leakage current: 230 Vac, 50 Hz 1.4 mA • EN55022, EN55011 conducted Input current: 120 Vac, with PFC 1.4 mA emissions level B 230 Vac, with PFC 0.51 A rms • EN61000-4-2,-3,-4, -5, -6 120 Vac, without PFC 1.40 A rms immunity compliant 230 Vac, without PFC 0.80 A rms • RoHS compliant Input fuse: UL/IEC127 S3.15 A, 250 Vac In live and neutral • LPX80 enclosure kit available • 2 year warranty Output Total regulation: Main output ±2.0% (line and load) Auxiliary outputs ±5.0% Rise time: At turn-on 1.0 s, max Safety Transient response: Main output 5.0% or 250 mV •VDE0805/EN60950/IEC950 25% step max. dev., 1ms max. File No. 1040100-3336-0096 at 0.1 A/µs recovery to 1% •License No. 114404 Temperature coefficient: ±0.02%/°C •UL1950 File No. E136005 Overvoltage protection: Main outputs 125%, ±10% •CSA C22.2 No. 950 Short circuit protection: Cyclic operation Continuous File No. LR41062C Minimum output current: Single and multiple (See Note 6) •China Compulsory Certification 60950 *NLP65-76xx version only process yellow 116 1375 1797 375 3405 313 2985 240 242 Embedded Power for Business-Critical Continuity 2607 All specifications are typical at nominal input, full load at 25° C unless otherwise stated. Rev.12.12.08_102 NLP65 Series 2 of 4 652 (11, 12) EMC Charateristics Conducted emissions: EN55022, FCC part 15 Level B ESD air: EN61000-4-2, level 3 Perf. criteria 1 ESD contact: EN61000-4-2, level 4 Perf. criteria 1 Surge: EN61000-4-2, level 3 Perf. criteria 1 Fast transients: EN61000-4-4, level 3 Perf. criteria 1 Radiated immunity: EN61000-4-3, level 3 Perf. criteria 2 Conducted immunity: EN61000-4-6, level 3 Perf. criteria 2 General Specifications Hold-up time: 120 Vac, 60 Hz 16 ms @ 65 W 230 Vac, 50 Hz 78 ms @ 65 W Efficiency: 120 Vac, 65 W 72% typical Isolation voltage: Input/output 3000 Vac Input/chassis 1500 Vac Switching frequency: Fixed 100 kHz, ±5 kHz Approvals and standards: (see EN60950, VDE0805 Notes 9, 13) IEC950, UL1950, CCC60950 CSA C22.2 No. 950 Weight: 283 g (10 oz) MTBF demonstrated: MIL-HDBK-217F 150,000 hours min Environmental Specifications DERATING CURVE Thermal performance: Operating 0° C to +70 °C Output Power (Watts) (See derating curve) 75W 20 CFM FORCED AIR COOLING (See notes 1, 3, 10) Non-operating -40 °C to +85 °C 65W 50 °C - 70 °C ambient, Derate to 50% load convection cooled 0 °C to 50 °C, ambient, 65 W NATURAL 38W CONVECTION convection cooled 32W COOLING 0 °C to 50 °C, ambient 75 W 20CFM forced air (See Note 10) Peak (0 °C to 50 °C, 60 s) See table 0°C 10°C 20°C 30°C 40°C 50°C 60°C 70°C Relative humidity: Non-condensing 5 to 95% RH Altitude: Operating 10,000 feet max. Non-operating 30,000 feet max. Vibration (See Note 5): 5-500 Hz 2.4 G rms peak Shock per MIL-STD-810E 516.4 Part IV process yellow 116 1375 1797 375 3405 313 2985 240 242 Embedded Power for Business-Critical Continuity 2607 Rev.12.12.08_102 Output Current NLP65 Series Output Total Non-harmonic Harmonic Ground Ripple (4) Voltage Regulation (6) Corrected Corrected Pin (12, 14, 17)  of 4 652 Max (1) Peak (3) Fan (10) +5 V (IA) 7.5 A 9.1 A 8 A 50 mV ±2.0% NLP65-7608J NLP65-9608J NLP65-X608GJ +12 V (IB) 2.5 A 3.3 A 3 A 150 mV ±5.0% –12 V 0.65 A 0.81 A 0.8 A 120 mV ±5.0% +5 V (IA) 7.5 A 9.1 A 8 A 50 mV ±2.0% NLP65-7610J NLP65-9610J NLP65-X610GJ +15 V (IB) 2.2 A 2.9 A 2.5 A 150 mV ±5.0% –15 V 0.65 A 0.85 A 0.8 A 150 mV ±5.0% (15) +5 V 7.0 A 9.1 A 8.0 A 50 mV ±2.0% NLP65-3322J +24 V 1.5 A 2.6 A 2.0 A 240 mV ±5.0% +12 V 0.7 A 1.0 A 1.0 A 120 mV ±5.0% +5 V (IA) 7 A 9.1 A 8 A 50 mV ±2.0% NLP65-7620J NLP65-9620J NLP65-X620GJ +24 V (IB) 2 A 2.6 A 2 A 240 mV ±5.0% +5 V (IA) 7 A 9.1 A 8 A 50 mV ±2.0% NLP65-7629J NLP65-9629J NLP65-X629GJ +12 V (IB) 2.5 A 3.3 A 3 A 150 mV ±5.0% +5 V 10 A 13 A 12 A 50 mV ±2.0% NLP65-7605J NLP65-9605J NLP65-X605GJ +12 V 5.4 A 7 A 6.5 A 120 mV ±2.0% NLP65-7612J NLP65-9612J NLP65-X612GJ +15 V 4.4 A 5.7 A 5.3 A 150 mV ±2.0% NLP65-7615J NLP65-9615J NLP65-X615GJ +24 V 2.7 A 3.5 A 3.5 A 240 mV ±2.0% NLP65-7624J NLP65-9624J NLP65-X624GJ Notes 1 Natural convection cooling. Models NLP65-X629J, NLP65-X608J, NLP65- 11 Conducted emissions testing were performed using the standard EN55022 set- X610J must not exceed 62.5 Watts continuous output power with natural up with a stand alone NLP65 unit placed on a grounded metal plate with a line convection. Model NLP65-X620J not to exceed 65 Watts continuous output choke on the AC input and ground wires (i.e. the wires are looped through an power with natural convection. Model NLP65-3322J must not exceed 60 Watts EMI suppression toroid). continuous output power with natural convection. For system compliance it is usually necessary to install an ‘off-the-shelf’ AC 2 When the input voltage is less than 90 Vac the operating temperature range is inlet with an integral line filter in the system chassis or to install a line choke 0 °C to +40 °C. The ripple and regulation specifications may not be met. on the input wires as close as possible to AC entry point of the system chasssis. 3 Peak output current lasting less than 60 seconds with duty cycle less than 5%. Please contact the applications group for assistance with EMI compliance. During peak loading, output voltage may exceed total regulation limits. 12 The NLP65 units with the suffix ‘G’ is the ground pin and ground choke option. 4 Figure is peak-to-peak for convection power rating. Output noise J2, L6 and JP10 are included. J2 is a safety agency approved grounding pin, L6 measurements are made across a 20 MHz bandwidth using a 6 inch twisted is a ground choke and JP10 is a jumper. This option is intended for use in non- pair, terminated with a 10 µF electrolytic capacitor and a 0.1 µF ceramic metallic chassis applications where grounding is not possible via the mounting capacitor. screws. The ground choke is provided to assist system EMC compliance. When 5 Three orthogonal axes, random vibration 10 minutes for each axes, 2.4 G rms 5 performing conducted emissions testing on stand alone units, the ‘G’ option Hz to 500 Hz. is required to meet level B. To order simply add the suffix ‘G’ to the standard 6 A minimum load on the main output is required for proper start up. For model number, e.g. NLP65-7608GJ, NLP65-9608GJ. This option is available for multiple outputs and single +5V output, the minimum load on the +5 V is both the PFC and non-PFC versions. 0.2 A. For single outputs greater than +5 V the minimum load is 0.1 A. To 13 All models require a minimum mounting stand-off of 0.25 inches (6.35 mm) in maintain stated regulation then: the end use product. for single output units 14 The NLP65-9608J is available with an enclosure. To order an enclosed version, I ≥ 0.2 A see model numbering options below. for multiple output units 15 No PFC version, EN61000-3-2 is not applicable to this model. 0.25 ≤ I(A)/I(B) ≤ 5, for I(A) ≥ 0.2 A. 16 The ‘J’ suffix indicates that these parts are Pb-free (RoHS 6/6) compliant. o 7 For optimum reliability, no part of the heatsink should exceed 120 C, and no 17 NOTICE: Some models do not support all options. Please contact your local o semiconductor case temperature should exceed 130 C. Emerson Network Power representative or use the on-line model number 8 CAUTION: Allow a minimum of 1 second after disconnecting line power when search tool at http://www.powerconversion.com. making thermal measurements. 9 This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. 10 Maximum continuous output power for all multiple output models must not exceed 75 Watts (70 watts for NLP65-3322J)with 20 CFM forced air cooling. Model Numbering Options 1 The enclosure version includes: IEC connector, on/off switch, wire harness output connector and fitted cover. To order, please add the suffix ‘E’ the model number, e.g. NLP65-9608EJ. See NLP65 enclosure for details. 2 A Safety earth ground pin and ground choke are available as an option. To order, please add the suffix ‘G’ the model number, e.g. NLP65-X608GJ. 3 To order an enclosure kit (unfitted), order the part number LPX80. process yellow 116 1375 1797 375 3405 313 2985 240 Embedded Power for Business-Critical Continuity 242 2607 Rev.12.12.08_102 NLP65 Series Americas Mechanical Drawing 4 of 4 652 5810 Van Allen Way 5.00 Carlsbad, CA 92008 (127.00) USA 4.550 Telephone: +1 760 930 4600 0.225 (115.57) (5.715) Facsimile: +1 760 930 0698 Europe (UK) J1 J3 Waterfront Business Park N Merry Hill, Dudley 1 3 West Midlands, DY5 1LX 1 L United Kingdom Telephone: +44 (0) 1384 842 211 2.550 Facsimile: +44 (0) 1384 843 355 3.00 6 (64.770) (76.20) Asia (HK) T1 J2 14/F, Lu Plaza 2 Wing Yip Street C19 Kwun Tong, Kowloon Hong Kong Telephone: +852 2176 3333 Facsimile: +852 2176 3888 For global contact, visit: MAXIMUM COMPONENT Mounting HEIGHT 1.26 (32.00) www.powerconversion.com Hole Diameter TOLERANCE: .xxx 0.005" techsupport.embeddedpower@ .xx 0.02" 0.156 (4.00) emerson.com ALL DIMENSIONS IN INCHES (mm) While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Pin Connections Input and Output Mating Connectors Connectors J1 Emerson Network Power. The global leader in enabling AC (J1) Molex 26-60-4030 type Molex 09-50-3031 or equivalent with Molex Pin 1 AC Line business-critical continuity. 08-50-0105 or equivalent crimp terminals Pin 2 No Pin DC (J3) Molex 26-60-4060 Molex 09-50-3061 with Molex 2478 phos- AC Power Pin 3 AC Neutral phor bronze crimp terminals or equivalent. Connectivity J2 (On ‘G’ Suffic Only) Note: The input and output connectors are the same as those used on NFS40, NFN40, NAL40, NAN40 and NLP40. DC Power Pin 1 Safety Ground Embedded Computing Embedded Power Output Pin Connections Monitoring J3 SINGLE DUAL TRIPLE Outside Plant Pin 1 V (A) V (B) V (B) Power Switching & Controls Pin 2 V (A) V (A) V (A) Precision Cooling Pin 3 V (A) V (A) V (A) Racks & Integrated Cabinets Pin 4 Return Return Return Services Pin 5 Return Return Return Surge Protection Pin 6 Return N/C V (C) EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2008 Emerson Electric Co.