GE INTELLIGENT PLATFORMS VP7
Specifications
Form Factor
6U VMEbus
2x Parallel Port
Two bi-directional, IEEE 1284 compatible enhanced parallel ports (including EPP and ECP) for printer or general purpose I/O
4x Serial I/O
RS-232/422 Four async. 16550 compatible full duplex serial channels High-speed transfer up to 115.2 kbaud with 16 byte FIFOs, COM 1,COM 2: RS-232 or RS-422 interface, COM 3+4: RS-232 or RS-422 interface
Chipset
Intel 82443BX, 82371EB 100 MHz system bus with Pentium III and Mobile Pentium III 66 MHz system bus with Celeron PCI burst mode transfers faster than 110 Mbytes/sec 32-bit wide PCIbus (33 MHz)
EIDE
Ultra DMA/33 sync. DMA mode up to 33 Mbytes/sec PIO mode 4 and bus master IDE up to 16 Mbytes/sec 2 devices supported on-board
Environmental Specification
Please See Data sheet
Fast Ethernet - AMD 79C972
10/100 Mbits/sec controller with PCI local bus DMA 12 Kbytes FIFO buffers for Receive and Transmit 10BaseT and 100BaseTX auto-negotiation interface
Hard Disk or FlashDrive
Internal 2.5” IDE hard disk or 2.5” FlashDrive (up to 512 MB) for extended temperature range and higher shock/vibration immunity
Mechanical
6U, 2 slot wide (233 x 160 x 40 mm) including FlashDrive or Hard Disk
Memory
PC66/100 2 DIMM sockets for 64 to 512 Mbytes, 64-bit Optional with error correction (ECC)
PMC Extension Slot
IEEE P1386/1386.1 32-bit PCIbus interface with front panel I/O
Power Allowances - PMC slot
+5 V, +3.3V Total power max. 7W, ±12 V 50 mA each
Power Requirements
+5 V Required, +3.3V, 12V Only if required by mounted PMC module
Processor
Intel Celeron
VGA and LCD – CT 69030/69000
64-bit Windows accelerator and LCD flat panel interface On-chip high speed 4/2 Mbytes synchronous DRAM (83 MHz) Flexible 9, 12, 15, 18 or 24-bit panel TFT interface
Wide SCSI
SYM 53C875 Wide SCSI controller with PCI local bus DMA SCSI transfer speed up to 40 Mbytes/sec Active low power termination on-board
Features
- 2x IEEE 1284 parallel ports
- 2x USB
- 4x serial I/O with FIFOs RS-232 or RS-422 interface
- Celeron, 566 MHz
- Custom specific, low cost assembly versions
- Embedded NT, Windows 2000/ NT/ 98, QNX, VxWorks, Lynx, Linux, MS-DOS
- Fast Ethernet 10/100 Mbit
- FlashDrive up to 512 MB or local 2.5” harddisk
- Low Power Mobile CPUs
- Occupies 2 VMEbus slots only with Front and Rear I/O
- Optional –40°/+70°C
- PCIbus Enhanced IDE
- Pentium III, 500-850 MHz
- PMC extension slot
- Single +5 volt supply only
- Ultra compact all-in-one PC
- Up to 512 MB SDRAM w/ ECC
- VGA/LCD up to 1600x1200 4(2) MB high speed SDRAM
- Watchdog, NMI ticker, temperature sensor
- Wide SCSI up to 40 MB/sec
Datasheet
Extracted Text
VP7 VP7 VP7 VP7 ® All-In-One Celeron™/Pentium III PC 6U VMEbus Embedded Computer Features Celeron™, 566 MHz ® Pentium III, 500-850 MHz Low Power Mobile CPUs Ultra compact all-in-one PC Occupies 2 VMEbus slots only with Front and Rear I/O Embedded NT, Windows 2000/ NT/ 98, QNX, VxWorks, Lynx, Linux, MS-DOS Up to 512 MB SDRAM w/ ECC FlashDrive up to 512 MB or local 2.5” harddisk VGA/LCD up to 1600x1200 4(2) MB high speed SDRAM Fast Ethernet 10/100 Mbit Wide SCSI up to 40 MB/sec The VP7 VMEbus all-in-one 6U includes video interface, Ethernet, PCIbus Enhanced IDE single board computer is designed to SCSI, and PMC extension. This com- meet the needs of embedded applica- bined with a custom specific assembly PMC extension slot tion developers addressing markets service provides optimized price / like telecommunication, industrial performance for all kinds of OEM 4x serial I/O with FIFOs automation, medical, scientific, mili- applications. RS-232 or RS-422 interface tary and aerospace, and imaging. Sup- 2x IEEE 1284 parallel ports ported operating systems are Windows Rugged needs are addressed with 2x USB 2000/ NT/ 98, QNX, VxWorks, Lynx, extended temperature range of up to Watchdog, NMI ticker, Linux, MS-DOS and others. –40°C to +70°C, and features like temperature sensor LCD interface. The ultra compact all-in-one concept Single +5 volt supply only with flexible processor and RAM Special features include four serial Optional –40°/+70°C configurations, and an impressive channels with flexible RS-232 or RS- array of on-board peripherals 422 interfacing and single +5V sup- Custom specific, low cost ply. assembly versions VP7 VP7 VP7 VP7 ® All-In-One Celeron™/Pentium III PC 6U VMEbus Embedded Computer Block Diagram and Front Panel I/O Specifications VME64 - Tundra Universe IIB Chipset - Intel 82443BX, 82371EB ® ® Industry standard CA91C142B PCI to VMEbus controller 100 MHz system bus with Pentium III and Mobile Pentium III 60-70 Mbytes/sec transfer rate, full VMEbus system controller 66 MHz system bus with Celeron™ FIFOs for write posting, DMA controller with linked list support PCI burst mode transfers faster than 110 Mbytes/sec Master/slave transfer modes: BLT, ADOH, RMW, LOCK, RETRY 32-bit wide PCIbus (33 MHz) A32 / A24 / A16 and D64(MBLT) / D32 / D16 / D8 Cache level 1 level 2 *1 Processor - Slot 1-Adapter for Socket 370 and BGA2 Celeron™ 32 KB 128 KB, full speed ® *1 Scaleable processing power with flexible processor design Pentium III 32 KB 256 KB, full speed ® *1 Intel Celeron™: 566 MHz, Intel Pentium III: 850 MHz also valid for Mobile processor ® Intel Mobile Pentium III: 500MHz, 700 MHz Please see price list for latest CPU versions Memory - PC66/100 High efficiency on-board switching regulator (DC/DC) 2 DIMM sockets for 64 to 512 Mbytes, 64-bit Fanless cooling with heatsink Optional with error correction (ECC) Performance Winstone 99 Hard Disk or FlashDrive CPU Frequency Business High End Internal 2.5” IDE hard disk or 2.5” FlashDrive (up to 512 MB) for Celeron 566 MHz 21.5 32.0 extended temperature range and higher shock/vibration immunity Mobile Pentium III 500 MHz 24.0 34.0 Mobile Pentium III 700 MHz 26.1 43.4 Pentium III 850 MHz 27.0 47.0 (128 MB RAM, 1024x768 64K color, ST34502LW HD) VP7 VP7 VP7 VP7 ® All-In-One Celeron™/Pentium III PC 6U VMEbus Embedded Computer VGA and LCD – CT 69030/69000 BIOS Features 64-bit Windows accelerator and LCD flat panel interface AMI BIOS, in-system programmable Flash ROM On-chip high speed 4/2 Mbytes synchronous DRAM (83 MHz) CPU, memory and IDE auto-detection/selection Flexible 9, 12, 15, 18 or 24-bit panel TFT interface Integrated VGA, Ethernet and SCSI BIOS ROM Password protection, BIOS post, system and video BIOS shadowing CRT Resolution CT 69030 CT 69000 Extensive setup with remappable serial/parallel ports Diskless, keyboardless and videoless operation 1024x768 16M@100Hz 64K@100 Hz 1280x1024 16M@75Hz 256@75 Hz Front and Rear I/O (with transition module VP6-TM) 1600x1200 64K@60 Hz - The pinouts of the transition module connectors (rear I/O) corre- sponds to standard PC connectors (press-fit cables). Fast Ethernet - AMD 79C972 10/100 Mbits/sec controller with PCI local bus DMA Function Front I/O On-board I/O Rear I/O (P2) 12 Kbytes FIFO buffers for Receive and Transmit VGA HD-15 - - 10BaseT and 100BaseTX auto-negotiation interface 10/100BaseTX RJ-45 - - PMC slot yes - - Wide SCSI – SYM 53C875 Keyboard mini-DIN - - Wide SCSI controller with PCI local bus DMA Mouse mini-DIN - - SCSI transfer speed up to 40 Mbytes/sec 2x USB 2x USB - - Active low power termination on-board Reset switch - yes LED LED - - EIDE COM 1 D-09 - - Ultra DMA/33 sync. DMA mode up to 33 Mbytes/sec COM 2-4 3x D09 3x 10-pin - PIO mode 4 and bus master IDE up to 16 Mbytes/sec LPT 1 D-25 26-pin - 2 devices supported on-board LPT 2 (36-pin) 26-pin - LCD 36-pin 40-pin - PMC Extension Slot - IEEE P1386/1386.1 Speaker - speaker - 32-bit PCIbus interface with front panel I/O EIDE - 44-pin, 2.0 mm - FlashDisk/ 4x Serial I/O - RS-232/422 2.5” HD Four async. 16550 compatible full duplex serial channels Wide SCSI - - 50-pin, 68-pin High-speed transfer up to 115.2 kbaud with 16 byte FIFOs Floppy - - 34-pin, 26-pin COM 1,COM 2: RS-232 or RS-422 interface Watchdog - - yes COM 3+4: RS-232 or RS-422 interface 2x Parallel Port Two bi-directional, IEEE 1284 compatible enhanced parallel ports (including EPP and ECP) for printer or general purpose I/O Floppy One channel 3.5“ floppy drive controller 720 KB and 1.44 MB 2x USB Two 12 Mbits/sec universal serial bus channels Keyboard PS/2 compatible Mouse PS/2 compatible Real-time clock RTC 146818 compatible, on-board Li-battery CMOS RAM 114 bytes non-volatile CMOS RAM EEPROM 4 kbit serial EEPROM for non volatile user data Watchdog Activates reset under software control (550 ms) Temp. Sensor Local temperature SW readable from –55°C to +125°C, 0.5°C increments NMI-Ticker User programmable NMI timer 0.3 to 18 ms for real-time applications Speaker Internal speaker (1.0 kHz to 4.2 kHz) LED Front panel LED (red) user programmable VP7 VP7 VP7 VP7 ® All-In-One Celeron™/Pentium III PC 6U VMEbus Embedded Computer Power Requirements Temperature +5 V Required Highest reachable operating temperature depends on processor +3.3V, �12V Only if required by mounted PMC module type, speed and ambient conditions (airflow) as shown below. All values under typical conditions w/o PMC module. *1 *1 *4 Power Consumption - +5 volt, typical current Operating Storage *2 128 MB memory, w/o keyboard, hard disk, modules, etc. Standard 0°C to +70°C –40°C to +85°C *3 CPU Frequency Idle Operating Extended –40°C to +70°C –40°C to +85°C *1 Complete board may be limited to a smaller temperature range Celeron™ 566 MHz 1.8 A 3.5 A ® by mounted PMC module. Mobile Pentium III 500 MHz 1.7 A 2.8 A *2 ® 0°C to +50°C with mechanical drives Mobile Pentium III 700 MHz 1.8 A 3.2 A *3 ® Extended not available with mechanical drives Pentium III 850 MHz 1.9 A 5.0 A *4 –40°C to +65°C with mechanical drives Idle measured at DOS prompt, max. powersaving Operating measured at DOS prompt, no powersaving max Tambient 70,0 VP7 Power Allowances - PMC slot +5 V, +3.3V Total power max. 7W 60,0 �12 V 50 mA each m obPIII500 m obPIII700 50,0 Ce l5 6 6 Mechanical PIII8 50 6U, 2 slot wide (233 x 160 x 40 mm) including FlashDrive or Hard 40,0 Disk 30,0 Airspeed m/s 0,0 1,0 2,0 3,0 4,0 5,0 6,0 Operating Storage Humidity 5 - 90% @ 40°C 5 - 95% @ 40°C Altitude 15.000 ft. (4.5 km) 40.000 ft. (12 km) MTBF Calculations are available in accordance with MIL-HDBK-217. Please contact factory. Safety All PWBs are manufactured with flammability rating of 94V-0 by UL recognized manufacturers VP7 VP7 VP7 VP7 ® All-In-One Celeron™/Pentium III PC 6U VMEbus Embedded Computer Ordering Information For detailed information call factory Hardware Accessories VMEbus Software SPC-R422C RS-422 driver for one channel (max. 2) DOS-VME VME driver for MS-DOS VP6-TM I/O transition module W98-VME VME-DLL and I/O driver for Windows 98 SC304F Floppy disk 3.5 inch, 19“-box: 3U/4HP, cable WNT-VME2 VME-DLL and I/O driver for Windows NT SC306HS04G SCSI hard disk 3.5“, 4.3 GB, 3U/6HP-box, cbl. QNX-VME VMEbus driver for QNX YLBSCSI304A Flatcable for external SCSI drive, 60 cm, VxWorks see Operating Systems 3U/4HP front panel, 50-pin Centronics conn. XCARD10C PMC module: PCcard adapter Chassis SCC784TU13VP7 StarterCage: 19", 7U, 84TE card cage, 13x 6U DOS-CARD MS-DOS PCcard driver for XCARD10 VME slots; 3x fan, 250W power supply +3,3V/12A, +5V/22A, +12V/7A, -5V/0,3A, - Operating Systems 12V/0,8A, EMC, SCSI CD-ROM, 3.5" floppy DOS-MD600x MS-DOS operating system drive, I/O transition module (VP6-TM), WIN-98xC Windows 98 operating system 0°C/+50°C WIN-NT4xC Windows NT 4.x operating system WIN-2000xC Windows 2000 operating system Special chassis, supplies, backplanes and drives on request. QNX-11252 QNX4 operating system QNX-11294 QNX4, Photon microGUI VXW-BVX7 VxWorks board support package Tornado 1 (w/o SCSI driver, with VMEbus driver) VXW2-BVX7 VxWorks board support package Tornado 2 (with VMEbus driver) WIN-ENT4xE Windows Embedded NT 4.x SBS or Industrial Computers GmbH&Co. KG USA and Canada: 6301 Chapel Memminger Str. 14, D-86159 Augsburg Hill Road, Raleigh, NC 27607-5115 Tel +49 (821) 5034-0, Fax -119 Tel (919) 851-1101, Fax -2844 E-mail sales@sbs-or.de E-mail sales@sbs-ec.com Internet www.sbs.com Internet www.sbs.com Specifications subject to change without notice. Third party brands and names are property of their owners. Rev. 06/29/2001
Frequently asked questions
How does Industrial Trading differ from its competitors?

Is there a warranty for the VP7?

Which carrier will Industrial Trading use to ship my parts?

Can I buy parts from Industrial Trading if I am outside the USA?

Which payment methods does Industrial Trading accept?

Why buy from GID?

Quality
We are industry veterans who take pride in our work

Protection
Avoid the dangers of risky trading in the gray market

Access
Our network of suppliers is ready and at your disposal

Savings
Maintain legacy systems to prevent costly downtime

Speed
Time is of the essence, and we are respectful of yours
Related Products

GE Intelligent Platform A16B-2200-0521 CPU Board - GE FANUC Series 15i - BASE 0 (Serial Spindle), Co...

GE INTELLIGENT PLATFORMS ACC-0602RC-000 CPU Boards - Rear Transition Module (RTM) designed to transi...
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods