CT8 ® 6U CompactPCI Single Board Computer Features • Low voltage Intel® Pentium III Processor-512k, 800MHz and higher • Optimized for Telcom Dual PMC applications • Ultra compact, 1 slot only • Redundant System Slot PICMG 2.13 compliant • Hot Swap (Full), PICMG 2.1 compliant • System / Non-System Slot Single PMC • 64-bit/66MHz cPCI bus • Extensive software support • Up to 2GB SDRAM with ECC • Flash Drive or local 2.5” hard disk CT8 is a high-performance 6U CompactPCT® CPU board with integrated low • VGA/LCD up to 1600 x power processor speed and dual Gigabit Ethernet channels. The CT8 supports full 1200 4MB SDRAM hot swap, redundant system slot and is capable of being used in a system or non- system slot. Adhering to the PICMG 2.16 dual Ethernet specification, the CT8 • Two Gigabit Ethernet ports supports the 64-bit/66MHz CompactPCI bus and is designed for use in a broad range 10/100/1000 BaseT PICMG of applications such as wireless, voice over packet, enterprise devices, medical 2.16 compliant imaging, command and control and high performance test and measurement • Two PMC extension slots, systems. 64-bit/66MHz and 32- Based on the low voltage Intel® Pentium® III processor 512k, the CT8 platform is bit/33MHz designed to support processors starting with 800MHz and higher. It offers low power consumption and eliminates the need for on-board ventilation. The CT8 provides a • IPMI PICMG 2.9 unique feature set, including up to 2GB of 133MHz SDRAM with ECC, two • Ultra ATA/100 independent on-board PCI buses, support for the 64-bit/66MHz CompactPCI backplane, and two PMC interfaces (64-bit/66MHz and 32-bit/33MHz). A high level of • Two Serial I/O with FIFOs functional integration (VGA/TFT, serial or parallel interfaces, IPMI controller, etc.) • IEEE 1284 parallel port within a single slot gives users the freedom to use the two PMC interfaces as extensions for their applications. The CT8 is also optionally available for the • Four USB ports extended temperature range of -40°/+55° C. • Watchdog, NMI ticker, The CT8 includes a Baseboard Management Controller (BMC) supporting the temperature sensor Intelligent Platform Management Interface (IPMI) architecture. It allows independent • Optional -40°/+55° C platform management between IPMI enabled boards, power supplies, fans and other accessories in a system. This feature can be used for autonomous monitoring, • Custom specific, low cost logging and recovery control functions. This is a key component in providing assembly versions enterprise class management for high-availability systems. A wide selection of operating systems is supported: Windows® XP, Windows® NT, TM Windows® 2000, QNX and Linux. Single Board Computers VGA and LCD - CT 69030 Specifications • 64-bit Windows accelerator and LCD flat panel interface • On-chip 4 MB synchronous DRAM (83MHz) • DVI-D interface (PanelLink®) for TFT displays up to 1024 x CompactPCI - HiNT HB6 PCI-to-PCI Bridge 768 x 16 • PICMG 2.0 R3.0 compliant cPCI local bus standard • Versions with front or Rear I/O available • 64-bit PCI-to-PCI bridge for up to 8 slots (33MHz) or Note: No video output is available if connector J4 is not populated and 5 slots (66MHz) if a PMC module is installed on PMC2 • Supports system and peripheral mode • J1+2, 2mm pin and socket connectors (IEC-1076-4-101) CRT Resolution Color Depth @ Refresh Rate 1024 x 768 16M @ 100Hz Redundant System Slot - compliant to PICMG 2.13 Draft 1280 x 1024 16M @ 75Hz • RSS Universal CPU operates as ‘Active Host CPU’, 1600 x 1200 64k @ 60Hz ‘Peripheral CPU’, or ‘Isolated CPU’. • Hot Swap Insertion/Extraction EIDE • Supports Hand-Over Command and Take-Over Command • Ultra ATA/100 sync. DMA mode up to 100 MB/Sec with the following control mechanism: • PIO mode 4 and bus master IDE up to 16MB/Sec - Host Control Transfer • Four devices supported via local EIDE connector and rear I/O - IPMI Initiated Transfer (planned) - Hot Swap Controlled Serial I/O - RS-232 and RS232/422/485 • Two assync. 16550 compatible full duplex serial channels at Processor - µFCBGA, Low Power Design rear I/O • Scalable processing power with flexible processor design • High-speed transfer up to 115.2 kBaud with 16 Byte FIFOs • Low voltage Intel® Pentium® III Processor 512k, 800MHz and • One user selectable RS232/422/485 interface (COM1) higher • COM1 optionally available at front • High efficiency on-board switching regulator (DC/DC) • Fanless cooling with heat sink Parallel Port • See pricelist for latest CPU versions • Bi-directional, IEEE 1284-compatible enhanced parallel port (including EPP and ECP) for printer or general purpose I/O Chipset - ServerWorks ServerSet™ III LE • 133MHz system bus IPMI - Zircon • PCI burst mode transfers up to 512MB/s (64-bit /66MHz) • Baseboard Management Controller with integrated ARM7 sup- • One 64-bit PCI bus with 66MHz porting the Intelligent Platform Management Interface (IPMI) • One 32-bit PCI bus with 33MHz architecture in compliance with PICMG 2.9 • Peripheral mode and BMC mode are supported Cache Level 1 Level 2 ® Pentium III 32 kB 512kB full speed Floppy • One channel 3.5” floppy drive controller Memory - PC133 • 720kB and 1.44MB • High-speed registered SDRAM • 64 to 2048MB, 72-bit with error correction (ECC) USB 1.0 • Rugged design with soldered chips • Four 12Mb/s universal serial bus channels Dual Gigabit Ethernet - Intel® 82546EB Keyboard • Highly integrated dual channel Ethernet controller with 64- • PS/2 compatible bit/66MHz PCI local bus DMA • 64kB transmit and receive FIFO Mouse • 10/100/1000BaseT auto-negotiation • PS/2 compatible • Versions with Front I/O (10/1000BaseT) available • Rear I/O pinning compliant with PICMG 2.16 Real-Time Clock • RTC 146818 compatible, on-board Li-battery Hard Disk or Flash Drive • Internal 2.5” IDE Hard Disk or 2.5” Flash drive (for extended CMOS RAM temperature range and higher shock/vibration immunity). (Not • 114 Bytes non-volatile CMOS RAM available when both PMC slots are occupied) (Onboard TM CompactFlash slot on request) EEPROM • 4 kbit serial EEPROM for non-volatile user data PMC Extension Slots - IEEE P1386/1386.1, PICMG 2.3 • One high bandwidth 64-bit/66MHz PMC interface directly Watchdog connect-ed to the internal PCI bus and one 32-bit/33MHz • Activates reset under software control (1 sec - 100 sec) PMC interface • Each PMC slot supports front panel I/O and rear I/O (opt. PIM) Timer • Rear I/O pinning in compliance with PICMG 2.3 • Activates IRQ under software control (200 µsec - 20 msec) (32-bit/33MHz PMC slot not available with additional front I/O, hard disk, or Flash Drive) Temp Sensor NOTE: 33MHz PMC plugged into 66MHz PMC slot will slow down • Local (lower card edge) and remote temperature (CPU die) Gigabit Ethernet and cPCI Bridge to 33MHz software readable from -65°C to +127° C, 1.0°C increments LEDs Power Requirements • Two front panel LEDs, hot swap (blue) and power OK/user • +5V, +12V, +3.3V Required (green/red) • -12V Only if required by mounted PMC module • RSS operation mode indicated by status LED (amber) Power Consumption Hot Swap - compliant to PICMG 2.1 • 256 MB memory, w/o keyboard, hard disk, modules, etc. • Peripheral mode: Board can be inserted or removed in a powered system Pentium® III 5V 3.3V Total Power • System controller mode: Other, non-system boards can be 800MHz 2.6A 2.4A 21W removed or added with power on. 933MHz 3.8A 2.4A 27W H.110 Friendly • Operating values measured at DOS prompt, no power saving • Version with non-populated J4 (see Front and Rear I/O • +12V: 30mA for Hot Swap functionality table) does not interfere with H.110 bus on P4 Power Allowances - PMC Slot BIOS Features • +5V, +3.3V: Total Power Max. 7.5W • New AMI BIOS Core 8, in-system programmable Flash ROM • ±12V: 50mA each • CPU, memory and IDE auto-detection/selection • Integrated VGA, and Ethernet BIOS ROM Mechanical - PICMG 2.0 • USB Mass Storage support • 6U, 1 slot wide • Password protection, BIOS post, system and video BIOS • 233 x 160 x 20.32 mm (including Flash drive or hard disk) shadowing • Extensive setup with remappable serial/parallel ports Temperature • Operation without disk, keyboard and video • Note: For detailed information about the operating temperature • Remote BIOS through serial port (planned) behavior of the board of any style it is absolutely necessary to consult the manual. The processor type and speed, the use or Software not use of Ethernet and video, and the type of cooling • The following software is supported to the extent listed influences the board temperature range. below. • All values under typical conditions without PMC module OS Available *1 *1,*4 Operating Storage *2 Standard 0° to +55°C -40° to +85°C Win NT4 √ *3 Extended -40° to +55°C -40° to +85°C Win 2000 √ Win XP √ QNX 4+6 √ *1 The complete board may be limited to a smaller VxWorks √ temperature range by mounted PMC module Linux √ *2 0° C to +50° C with rotating mass storage *3 Extended not available with rotating mass storage Front and Rear I/O (with Transition Module CTM12) *4 -40° C to +65° C with rotating mass storage • The pin out of the transition module connectors (rear I/O) correspond to standard PC connectors (press-fit cables) Humidity Function Front Rear (J3/J5) Rear (J4) • Operating 5 - 95% @ 40°C VGA D-15*4 - 10-pin • Storage: 5 - 95% @ 40°C ETH 1 RJ45*4 RJ45 - Altitude ETH 2 RJ45*4 RJ45 - • Operating: 15,000 ft (4.5 km) KBD+Mouse Mini-DIN - *1 • Storage: 40,000 ft (12 km) Reset Button - *1 Multiple I/O*1 - - 26-pin MTBF Floppy - - 26-pin, 125mm • Calculations are available in accordance with MIL-HDBK-217 LEDs 3x - - Please contact factory USB 0–3 USB 0 - *1,*2 EIDE Pri.*3 - 40-pin - Safety COM 1 D-09 10-pin - • Designed to meet standard UL1950, CE class A, FCC-A COM 2 - D-09/10-pin - LPT - - 26-pin LCD - - DVI-D PMC 1 Yes PIM / 64-pin - PMC 2 Yes PIM / 64-pin - *1 Multi-I/O connector w/ Keyboard, Mouse, 2x USB, Reset, Watchdog and speaker *2 Additional 10-pin connector for 4x USB *3 Second I/F for 2.5” hard disk or Flash drive onboard *4 32-bit/33 MHz PMC slot not available with additional Front I/O CT8 Block Diagram Ordering Information Hardware Accessories CTM12: I/O transition module for 6U backplane (IEEE 1101.11-1998 compliant) supporting hot swap SC304F: Floppy Disk 3.5 in., 19 in. box: 3U/4HP, cable SC306H10G0: IDE Hard Disk 3.5 in., 10 GB, 19 in. box: 3U/4HP, cable ZKAAPS2SPLIT: Cable for Keyboard and Mouse on front panel Operating Systems Extensive operating systems support is available, see page 3 of this document. Chassis with power supplies, backplanes and drives on request. For detailed information and further options contact SBS Technologies Corporate Headquarters European Headquarters 2400 Louisiana Blvd. NE, #5-600 Memminger Str. 14 Albuquerque, NM 87110-4316 D-86159 Augsburg, Germany Tel 505.875.0600 Fax 505.875.0400 Tel +49-821-5034-0 Fax +49-821-5034-119 Email info@sbs.com Email aug-info@sbs.com For additional contact information, please visit our web site at www.sbs.com Specifications subject to change without notice. All trademarks and logos are property of their respective owners. ©2004 SBS Technologies, Inc. 20050301