CT7 Hot Swap System / Non-System ® 6U cPCI Embedded Computer Features • Intel® Pentium® III processor, 500 MHz to 850 MHz and Intel® Celeron® processor 566 MHz • Optimized for telecom applications • Ultra compact, 1 slot • Hot Swap • System & Non-system mode • Dual bus support with up to 14 slots • Extensive Software Support • Up to 1 GB SDRAM with ECC • Flash drive or local 2.5” hard disk • VGA/LCD up to 1600x1200, 4(2)MB high speed SDRAM CT7 is a 6U CompactPCI all-in-one single board computer. The CT7 supports • Two Fast Ethernet 10/100 system / non-system and hot-swap and is designed to meet the needs of embedded Mbit application developers addressing markets like telecommunication (high bandwidth, • Wide SCSI up to 40 MB/s broadband data or intelligent network switching), industrial automation, medical, PCI bus Enhanced IDE scientific and imaging. • 1(2) PMC extension slots The ultra compact single slot, all-in-one design with flexible processor and RAM • IPMI configuration, and an impressive array of on-board peripherals includes two Fast- • Two serial I/O with FIFOs Ethernet channels, one SCSI interface and one PMC extension slots. In a two slot • IEEE 1284 parallel port solution with an additional bridge piggy and a second CompactPCI backplane up to 14 CPCI slots and two PMC slots are supported. This combined with a custom • Two USB ports specific assembly service provides an optimized price / performance ratio for all kinds • Watchdog, NMI ticker, of OEM applications. temperature sensors • Optional –40°/+70°C Special feature includes a Baseboard Management Controller (BMC) supporting the • Customer specific, low cost Intelligent Platform Management Interface (IPMI) architecture and UL certification. assembly versions Supported operating systems are Windows 2000/ NT/XP, QNX and VxWorks. Single Board Computers Specifications Dual Fast Ethernet – Intel 82559ER • 10/100 Mbits/sec controller with local bus DMA CompactPCI – Intel 21554 • 3 Kbyte Transmit FIFO and 3 Kbyte Receive FIFO • 64-bit PCI-to-PCI bridge for up to 8 slots (33 MHz) • 10BaseT and 100BaseTX auto-negotiation interface • J1+2, 2mm pin and socket connectors (IEC-1076-4-101) • Optional bridge piggy for second CompactPCI bus at J1 + J2 Wide SCSI – SYM 53C875 • Supports system and non-system mode • Wide SCSI controller with PCI local bus DMA • SCSI transfer speed up to 40 Mbytes/sec Processor – Socket 370 (FCBGA or BGA2) • Active low power termination on-board • Scalable processing power with flexible processor design • Intel Celeron processor: 566 MHz EIDE • Intel Pentium III processor: 700 and 850 MHz • Ultra DMA/33 sync. DMA mode up to 33 Mbytes/sec • Intel Mobile Pentium III processor: 500 and 700 MHz • PIO mode 4 and bus master IDE up to 16 Mbytes/sec • High efficiency on-board switching regulator (DC/DC) • 3 (4) devices supported via local EIDE connector and rear I/O • Fanless cooling with heat sink • See price list for latest CPU versions Two Serial I/Os – RS-232 • Two async. 16550 compatible full duplex serial channels Performance • High-speed transfer up to 115.2 kbaud with 16 byte FIFOs Winstone 99 CPU Frequency Business High End Parallel Port Celeron 566 MHz 21.5 32.0 • Bi-directional, IEEE 1284 compatible enhanced parallel port Mobile P III 500 MHz 24.0 34.0 (including EPP and ECP) for printer for printer or general Mobile P III 700 MHz 26.1 43.4 purpose I/O Pentium III 700 MHz 26.1 43.4 Pentium III 850 MHz 27.0 47.0 IPMI - Zircon (128 MB RAM, 1024x768 64K color, ST34502LW HD) • Baseboard Management Controller with ARM7 supporting the *1, Intelligent Platform Management Interface (IPMI) architecture Chipset – Intel 82443BX 82371EB in compliance with CompactPCI PICMG 2.9 • 100 MHz system bus with Pentium III and Mobile Pentium III • Peripheral Mode and BMC Mode are supported • 66 MHz system bus with Celeron processor • PCI burst mode transfers up to 110 MB/s Dual Bus Support – compliant to PICMG CompactPCI 2.6 • 32-bit wide PCI bus (33 MHz) • Supports up to 14 CPCI slots with standard backplanes (one *1 CT7 V4.x: Intel 82443GX left and one right justified each) via second CPCI interface on optional 6U bridge piggy back board. Cache Level 1 Level 2 • Avoids second CPCI via P4/5 requiring special backplanes *1 Pentium III 32 KB 256 KB, full speed *1 Celeron 32 KB 128 KB, full speed Floppy One channel 3.5” floppy drive controller *1 also valid for Mobile processor 720 KB and 1.44 MB 2x USBs 12 Mbit/sec universal serial bus channels Memory – PC66/100 Keyboard PS/2 compatible • High-speed SDRAM Mouse PS/2 compatible *1 • 64 to 1024 Mbytes , 72-bit wide with error correction (ECC) Real-time clock RTC 146818 compatible, on-board Li-battery • Rugged design with soldered components CMOS RAM 114 bytes non-volatile CMOS RAM *1 CT7 V2.x, V3.x: 512 Mbytes EEPROM 4 kbit serial EEPROM for non-volatile user data Hard Disk or Flash Drive Watchdog Activates reset under SW control (550ms) • Internal 2.5” IDE hard disk or 2.5” Flash Drive (for extended Temp. Sensor Local and remote temperature (CPU case) temperature range and higher shock/vibration immunity) SW readable from -65°C to +127°C, 1°C increments 1 (2)x PMC Extension Slots - IEEE P1386/1386.1 3x LEDs Three front panel LEDs hot swap (blue), • 64-bit PCI bus interface with front panel I/O and rear I/O Power OK (green) and user • One or two (with bridge piggy board) PMC slots programmable (red) VGA and LCD – CT 69030/69000 Hot Swap • 64-bit Windows accelerator and LCD flat panel interface • In peripheral mode the board can be inserted or removed in a • On-chip high-speed 4/2 Mbytes synchronous DRAM (83 MHz) powered system. It is not supported for a 66 MHz CPCI • Flexible 9, 12, 15, 18 or 24-bit Panel TFT interface system. • In system controller mode other, non system boards can be CRT Resolution CT 69030 CT 69000 removed or added with power on. 1024 x 768 16M @ 100Hz 64K @ 100Hz • Access to or interrupt on backplane /ENUM signal supported 1280 x 1024 16M @ 75Hz 256 @ 75Hz 1280 x 1200 64K @ 60Hz - H.110 Friendly Power Requirements • +5 V, +12V Required • Versions with non populated J4 (see table below) do not • +3.3 V, -12 V Only if required by PMC module interfere with H.110 bus on P4 Power Consumption - +5V, typical current BIOS Features • 128 MB memory, w/o keyboard, hard disk, modules, etc. • AMI BIOS, in-system programmable Flash ROM • CPU, memory and IDE auto-detection/selection CPU Frequency Idle Operating • Integrated VGA, Ethernet and SCSI BIOS ROM Celeron 566 MHz 2.3 A 4.1 A • Password protection, BIOS post, system and video BIOS Mobile P III 500 MHz 2.2 A 3.4 A shadowing Mobile P III 700 MHz 2.3 A 3.8 A • Extensive setup with remappable serial/parallel ports Pentium III 700 MHz 2.3 A 5.1 A • Operation without disk, keyboard and video Pentium III 850 MHz 2.4 A 5.8 A Software • The following software is supported to the extent listed • Idle measured at DOS prompt, max power saving below. • operating measured at DOS prompt, no power saving OS Available . Power Allowances - PMC slot WIN XP/2000/NT √ QNX 6 √ • +5 V, +3.3V: Total power max. 7 W VxWorks √ • ±12 V: 50mA each Front and Rear I/O (with transition module CTM10) Mechanical • The pin out of the transition module connectors (rear I/O) • 6U, 1 slot wide (233 x 160 x 20.32mm) incl. Flash Drive corresponds to standard PC connectors (press-fit cables). • 6U, 2 slot wide (233 x 160 x 40.64mm) with bridge piggy (option) Function Front Rear Rear • Conforms to PICMG CompactPCI 2.0 J3 + J5 J4 VGA D-15 10-pin - Temperature Eth 1 RJ-45 10-pin - • Note: For detailed information about the operating temperature Eth 2 RJ-45 10-pin - behavior of the board of any style it is absolutely necessary to Keyb+Mouse mini-DIN - - consult the manual. The processor type and speed, the use or Reset button - - not use of Ethernet and video, and the type of cooling *1 - Multi-I/O 26-pin - influences the board temperature range. Floppy - 26-pin, 1.25mm • All values under typical condition without PMC module LED 3x - - USB USB - - *1 *1*4 *2 Range Operating Storage EIDE - 44-pin - *2 Standard 0°C to +70°C –40°C to +85°C COM 1 D-09 10-pin - *3 Extended –40°C to +70°C –40°C to +85°C COM 2 - 10-pin - LPT - 26-pin - *1 Complete board may be limited to a smaller temperature LCD - - 40-pin range by mounted PMC module SCSI - 50-pin (narrow) *2 0°C to +50°C with mechanical drives 68-pin (wide) *3 Extended not available with mechanical drives PMC Yes 64-pin - *4 -40°C to +65°C with mechanical drives 1 Multi-I/O connector with keyboard, mouse, 2x USB, Humidity reset, watchdog and speaker 2 • Operating: 5 - 95% @ 40°C Additional 44-pin onboard connector for Flash drive or • Storage: 5 - 95% @ 40°C hard disk Altitude • Operating: 15.000 ft. (4.5 km) • Storage: 40.000 ft. (12 km) MTBF • Calculations are available in accordance with MIL-HDBK-217. Please contact factory. Safety • Certified to standard UL1950 CT7 Block Diagram Ordering Information Hardware Accessories CTM10: I/O transition module for 6U backplane CT7-TM: I/O transition module for 6U backplane (IEEE 1101.11-1998 compliant) CBUS-IO: Carrier for transition module (male-male) SC304F: Floppy disk 3.5 inch, 19“-box: 3U/4HP, cable SC306HI10G0: IDE hard disk 3.5“, 10 GB, 19“ box: 3U/6HP, cable YLBSCSI304A: Flat cable for external SCSI drive, 60cm (23.6inch) ZKAAPS2SPLIT: Cable for keyboard and mouse on front panel SCC784TE08CT7: CT7 starter cage 7U, 84HP, 8 slots, fans, 250W power supply, CDROM, hard disk, floppy drive Operating Systems Extensive operating systems support is available (see page 3). Chassis with power supplies, backplanes and drives on request. For detailed information and further options, contact SBS. Corporate Headquarters European Headquarters 2400 Louisiana Blvd. NE, #5-600 Memminger Str. 14 Albuquerque, NM 87110-4316 D-86159 Augsburg, Germany Tel 505.875.0600 Fax 505.875.0400 Tel +49-821-5034-0 Fax +49-821-5034-119 Email info@sbs.com Email aug-info@sbs.com For additional contact information, please visit our web site at www.sbs.com Specifications subject to change without notice. All trademarks and logos are property of their respective owners. ©2004 SBS Technologies, Inc. 20050302