GE Intelligent Platforms CT12 High Performance Dual Core 6U CPCI Single Board Computer Features ® ® • IPMI 2.0 PICMG 2.9 The BIOS Flash is optionally backed with a • Intel Core™ i7 or Core i5 processors second Flash device in order to recover the • Watchdog, temperature sensors - Dual core, up to 2.53 GHz BIOS in the event the primary BIOS is • OS support: standard distribution - Integrated memory interface, 1066 MHz ® ® corrupted. The Flash device is large enough Linux and Windows • Single slot 6U CPCI form factor to optionally host additional pre-boot ® • Optional -40° C to +75° C operating • PICMG compliant applications, for example Built-In Test (BIT). temperature range • Up to 8 Gbyte DDR3 SDRAM (dual channel) with • Optional conformal coating ECC in main memory (soldered components) For telecom applications, the CT12 is • Customization on request • Up to 16 Gbyte NAND Flash (soldered) equipped with IPMI 2.0 functionality. • BIOS backup Flash • User EEPROM Supported operating systems for the CT12 ® ® ® ® The CT12 is a single slot 6U CompactPCI include Linux and Microsoft Windows as • Optional onboard SATA HDD ® SBC with an Intel Core™ i7 processor well as VxWorks. • Optional one or two PMC or XMC sites plus QM57 peripheral controller hub. The • Front I/O: ® assembly is fully compliant to the PICMG The CT12 is also available in an extended - Two Gigabit Ethernet ports specifications. operating temperature version (-40° C to - VGA +75° C). The upper limit of the temperature - One USB The CT12 is able to host one Dual Core range depends on the selected processor - One COM 3 processor with a core clock of up to 2.53 version and the optional population with • Rear I/O: GHz. The assembly is ready to accept PMC, XMC mezzanines or a SATA hard drive. higher performance processor variants - Two Gigabit Ethernet ports when introduced by Intel. - VGA 1 The CT12 is designed for use in a broad - DVI 1 and 2 range of applications such as telecom/ Four banks of DDR3 SDRAM components communications, industrial control and - Three SATA2 (3 Gb/s) interfaces are provided on the CT12 for a maximum automation, test, and measurement - COM 1 and 2 ports of 8 GBytes of main memory with ECC. systems, as well as server blade - Four USB ports The module also hosts up to 16 GByte applications. This, combined with a - GPIOs soldered NAND Flash through an IDE customer specific assembly service, - PMC/XMC I/O signals interface and may be provisioned with provides optimized price and performance higher Flash capacities when required for levels. specific applications. The onboard NAND Flash is an ideal storage media to keep Please contact GE Intelligent Platforms for a application specific data. current list of processors and OS versions supported on the CT12. CT12 High Performance Dual Core 6U CPCI Single Board Computer Front Dual Gigabit Ethernet Watchdog CT12 Safety and Reliability Benefits ® • Twin Intel 82574L PCI Express Ethernet controllers • Super I/O • 10/100/1000BaseT auto-negotiation Soldered processor and memory Temperature Sensors • Ordering option • CPU die and chipset die temperature software Increased immunity against shock and readable in the range of –15°C to +105°C Rear Dual Gigabit Ethernet vibration ® • Twin Intel 82574L PCI Express Ethernet controllers Soldered NAND Flash drive LED • 10/100/1000BaseT auto-negotiation • Front panel ACPI system Status indicator LED Higher immunity against shock and ® • Compliant to PICMG 2.16 (red/amber/green) vibration compared to CompactFlash • CompactPCI Hot swap (blue) on front panel Onboard Hard Disk or SSD Drive BIOS Backup Flash Optional internal 2.5" SATA hard disk or 2.5" SATA • Hot-Swap - compliant to PICMG 2.1 Fast recovery when BIOS upgrade got Solid State Drive (SSD) • Peripheral mode: full CompactPCI Hot Swap corrupted • Usage of SSD is recommended for high shock and • System Host mode: CompactPCI ENUM# event Optional Built-In Test routines for platform vibration immunity as well as extended temperature support through ACPI or legacy driver applications integrity tests Front and Rear I/O (Transition Module CTM20) HW Write Protect PMC/XMC Extension Slots Function Front Rear Protects onboard code and data against • Optional as PMC or XMC extension slots • Optional one or two extension slots unauthorized write access VGA 1  • Extension slot 1: PMC (64-bit PCI, up to 133 in PCI-X VGA 2  mode) or XMC with PCI Express x8 (Gen2, 2.5 Gbit/s) DVI 1 & 2  • Extension slot 2: PMC (64-bit PCI, up to 133 in PCI-X COM 1   Specifications mode) or XMC with PCI Express x8 (Gen2, 2.5 Gbit/s) COM 2  • Extension slot 2 is not available in case a 2.5" Processor - μFCBGA, Low Power Design USB 0 – 3  storage device is installed • Scalable embedded processing power USB 4  • PCI signaling is 3.3V, 5V tolerance • 32 nm process Ethernet 1,2  ® • Intel Core™ i7 processor, up to 2.53 GHz SATA Ethernet 3,4  • Cache: up to 4 MB, full speed • Three SATA2 (3 Gb/s) ports to rear I/O 1 SATA 2  • Dual core versions Serial I/O SATA 3-5  • Low power processor versions • Two async. 16550 compatible full duplex serial GPIO  ® • Intel Hyper-Threading technology (two threads per channels LEDs   core) • High-speed transfer up to 115.2 kbaud with 16 byte ® PMC 1 / XMC 1 I/O   Intel Turbo Boost support • FIFOs PMC 2 / XMC 2 I/O   • Two PCI Express x8 ports • User selectable RS-232/422/485 interfaces at rear Reset   ® • FDI and DMI interface to I/O Controller hub • COM3 RS-232 available at front via HarLink 1 • Contact GE Intelligent Platforms for current If Flash ROM option is not used connector processor versions Video/Graphics Interface BIOS Features • Intel integrated 3D graphics controller • New AMI Aptio UEFI, in-system programmable Processor Speed L2 Memory • One VGA port at front via HarLink connector Flash ROM MHz GHz MB • One VGA port plus two DVI-D ports at rear I/O • CPU, memory and SATA2 auto-detection/selection i7-610E 2.53 4 1066 • Integrated Ethernet PXE driver • Any two ports can be used for dual display operation i7-620LE 2.00 4 1066 Fully compliant support for OpenGL™ for all • USB mass storage support and booting capability • Windows operating systems and Linux (floppy, HDD, CDROM, and onboard Flash ROM i7-620UE 1.06 4 800 array) General Purpose I/O CompactPCI Password protection • • 13 GPIO (input or output) pins • PICMG 2.0 R3.0 compliant CPCI local bus standard • Headless operation Software configurable • • 64-bit PCI for up to 8 slots (33 MHz) or 5 slots (66 MHz) • Hardware Write Protection of programmable IPMI 2.0 • Supports both system Host and Peripheral Mode in a devices • Baseboard Management Controller supporting the single assembly Intelligent Platform Management Interface (IPMI) • 2 mm pin and socket connectors (IEC-1076-4-101) ® USB Ports architecture in compliance with PICMG 2.9 • One USB 2.0 connector on the front I/O Controller Hub • Peripheral mode and BMC mode are supported • Four USB 2.0 channels on rear • FDI and DMI interface to processor • IPMI is an optional function • Supplies I/O interfaces/functions to front and rear Keyboard and Mouse Software • 8 PCI Express ports • Via USB • Windows • Choice of four display channels • Legacy PS/2 controller emulation • Linux Main Memory Array • VxWorks Real-time Clock • Dual channel DDR3 SDRAM array: 4 banks soldered • RTC 146818 compatible Styles memory components • Li-battery Style A F • 144-bit wide with error correction (ECC) Configurable capacity: 1 GByte to 8 GBytes • EEPROM Ext. Temperature no yes 512 kbit serial EEPROMs for non-volatile user data • Conformal coating is a custom option. Flash ROM Memory • Up to 16 GBytes NAND Flash Timer • Accessed by processor through IDE • Integrated in Hub controller • Soldered down for high reliability • Legacy PC-AT timer • Wear leveling HPET High Precision Event Timer • CT12 High Performance Dual Core 6U CPCI Single Board Computer Specifications (continued) Block Diagram Power Requirements • +5 V, +3.3V, +12V • -12V if required by mounted PMC module Power Allowances – PMC/XMC Slots +5 V, +3.3 V: Total power max. 7.5 W • • ±12 V: 100mA each Power Consumption - typical operating current • Without keyboard, hard disk, Windows, 3D graphics active, Gigabit Ethernet channels not active, measured at DOS prompt, no power savings. 1 GB memory option – see manual. Temperature • Note: Consult the User's Manual or GE Intelligent Platforms for additional detailed information on the operating temperature behavior of the module. The CT12 operating temperature range is influenced by processor type and speed, operating altitude, and the type of cooling used in the host system. • All values under typical conditions without PMC/XMC module. Range Operating Storage Standard 0° C to +55° C –40° C to +85° C Extended -40° C to +75° C –40° C to +85° C Operating Storage Humidity 5 - 95% @ 40° C 5 - 95% @ 40° C Altitude 15.000 ft. (4.5 km) 40.000 ft. (12 km) Mechanical – PICMG 2.0 • 6U, 1 slot wide, 233 mm x 160 mm x 20 mm with Flash drive or hard disk Altitude Ordering Information • Operating: Sea level to 15,000 ft. (4.5 km) CT12AUF2K10A 6U cPCI PC, single slot, Core i7-610E 2.53 GHz, 4 GB DDR3, 4 GB NAND drive, 2x • Storage: Sea level to 40,000 ft. (12 km) front GigE, 2x rear GigE, 2x SATA, VGA (front), COM (front), VGA (rear), 2x COM (rear), 2x USB (rear), 4x SATA (rear) Shock and Vibration Designed to meet VITA47 class EAC1 and EAC3 CT12CUF2K10A 6U cPCI PC, single slot, Core i7-620LE 2.0 GHz, 4 GB DDR3, 4 GB NAND drive, 2x • front GigE,. 2x rear GigE, 2x SATA, VGA (front), COM (front), VGA (rear), 2x COM MTBF (rear), 2x USB (rear), 4x SATA (rear) • Prediction calculations are available in CTM20A10A 6U I/O transition module for CT12 without onboard SATA drive with all onboard accordance with MIL-HDBK-217. Please contact and face plate I/O ports. GE Intelligent Platforms. YLB-CR12-01 Front I/O COM port cable (appr. 200 mm), Harlink connector to serial connector Safety YLB-CR12-02 Front I/O VGA port cable (appr. 200 mm), Harlink connector to VGA connector • Designed to meet standard UL1950, CE class A, CR12-SDK-LINUX System Development Kit for Linux (Fedora 12, RHEL 5.4, Suse 11.2) FCC-A BVXW-CRCT12-01M Board Support package for Workbench/VxWorks 6.x with maintenance TVXW-CRCT12-01M Board Support Package and Enhanced Support package for Workbench/VxWorks 6.x with maintenance VXW6-ECR12 VxWorks 6.x Board Support Package (BSP) and Extended Board Support Package (ESB) CR12-SDK-WIN System Development Kit for Windows XP, (planned Windows7) Operating Systems For detailed information and further options, contact GE Intelligent Platforms. GE Intelligent Platforms Contact Information Americas: 1 800 322 3616 or 1 256 880 0444 Global regional phone numbers are listed by location on our web site at www.ge-ip.com/contact defense.ge-ip.com ©2011 GE Intelligent Platforms. All Rights Reserved. All other brands or names are property of their respective holders. Specifications are subject to change without notice. 07.11 GFA-1334