Boot Monitor

VxWorks Boot Loader Alternatively PMON Boot Loader and functions

Cache

Processor Level 1 Level 2 Cache MPC8641 32 Kbyte 1 Mbyte MPC8641D 32 Kbyte 2x 1 Mbyte

Chipset

Up to 600 MHz internal MPX bus DDR2 memory interface up to 667 MHz data rate PCI Express Ethernet MAC controllers Multi processor interrupt controller Four channel DMA controller

CompactPCI Interface Compliance standards

PICMG® 2.0 R3.0 compliant CPCI 32-bit/66 MHz local bus standard System/non-system PCIe-PCI bridge from Pericom for up to 7 slots J1+2, 2 mm pin and socket connectors(IEC-1076-4-101)

Environmental

Temperature Note: For detailed information about the operating temperature behavior of the board of any style it is absolutely necessary to consult the manual. The processor type and speed, altitude, the use or not use of Ethernet, ambient conditions and the type of cooling influence the board temperature range. All values under typical conditions without PMC. Range Operating Storage Standard 0 °C to +70 °C –40 °C to +85 °C Extended –40 °C to +85 °C –40 °C to +85 °C Rugged –40 °C to +85 °C –55 °C to +105 °C Humidity Operating: 5 – 95 % @ 40 ° Storage: 5 – 95 % @ 40 °C Non condensing Altitude Operating: 15.000 ft. (4.5 km) Storage: 40.000 ft. (12 km) Vacuum for conduction cooled board (contact factory) Shock (3 axis, up & down, 5 hits/direction) Styles 1, 3: 12 g / 6 ms Style 8: 100 g / 6 ms, 40 g / 11 ms Vibration (60 minutes each axis) Styles 1, 3: 2 g rms @ 5 to 100 Hz Style 8: 14 g rms @ 5 to 2000 Hz

EPROM

1 Mbit (128 Kbyte) serial EEPROMs for non-volatile user data

Features

Up to 256 Mbyte 32-bit wide Flash for boot and application code Software and hardware write protected

GPIO

MPC8641 integrated Ethernet MAC controller Transmit and receive FIFO MV88E1118 PHYs with GMII interface Two 10/100/1000BaseX with auto-negotiation Available at rear

Graphic Processor

eight GPIO (input or output) pins with interrupt capability Available at rear I/O shared with PMC I/O signals

Mechanical

3U, 1 slot wide, (100 x 160 x 20 mm)

Memory

High-speed up to 667 MHz (PC5400) DDR2 SDRAM 64 bit wide with optional ECC Up to 1 Gbyte with soldered components

MTBF

Calculations are available in accordance with MIL-HDBK-217 FN2

Networking

Simtek STK17TA8 device 128 Kbyte autostore nvSRAM Real time clock (no backup)

PCI

PCI buses provided through PCIe/PCI bridges Pericom PI7C9110 and PI7C9X130

PMC #1

64-bit/100 MHz PCI-X With front panel I/O and partly rear I/O 100 MHz operation with 3.3 V I/O 33 MHz operation with 5 V I/O tolerance Supports ccPMC Draft Standard VITA 20 – 199x with style 8

Power Connector

+5 V, +3.3 V: Total power max. 7.5 W ±12 V: 100mA each

Power Consumption

512 Mbyte memory bank and without PMC module. MPC8641 5 V 3.3 V Total Power 1.0 GHz LV Dual 3.4 A 4.0 A 26 W 1.33 GHz Dual 6.4 A 4.0 A 41 W Operating estimated at VxWorks prompt, no power saving

Power Requirements

+5 V, +3.3 V Required -12 V, +12 V If required by mounted PMC module

Processor

Single or dual core PowerPC e600 1000 MHz to 1333 MHz Integrated L2 cache with optional ECC High efficiency on-board switching regulator (DC/DC) COP interface at rear I/O Fanless cooling with heat sink

Safety Criteria

All PCBs are manufactured with flammability rating of 94V-0 by UL recognized manufacturer Designed to meet standard UL 60950

Serial

Integrated in MPC8641 Two async. 16550 compatible full duplex serial channels Available on the rear High-speed transfer up to 115.2 Kbaud with 16 byte FIFOs COM1 with RS-232 and COM2 with RS-422/485 driver Each interface with RxD, TxD, RTS, CTS

Technology

CPU die and heat sink temperature software readable in the range of –55 °C to +127 °C

Video

Designed to meet VITA 47 class EAC1, EAC3 and ECC4

Watchdog Timer

Can drive interrupt or reset Configurable granularity from 256 ms to 16 s