GE INTELLIGENT PLATFORMS CL9
Specifications
Form Factor
PICMG
System Chipset
Intel 855GME
Video Chipset
Intel 855GME
Audio
S/PDIF digital output (optical) Line in Headphone out Note: the audio interface down not operate belovw 0C
BIOS
New AMI BIOS core 8, in-system programmable Flash ROM CPU, memory, and IDE auto detection/selection Integrated VGA, and etheret BISO-RAM USB mass storage support Password protection, BIOS post, system and video BIOS shadowing
Cache
Cache Level 1 Level 2 Pentium M (90nm) 32 KB 2 MBYTE, full speed Pentium M (130nm) 32 KB 1 MBYTE, full speed Celeron M (130nm) 32 KB 1 MBYTE, full speed Celeron M (90nm) 32 KB 512KByte, full speed
Chipset
Intel 855GME with 6300ESB 400 MHz system bus to processor PCI burst mode transfers up to 512 MB/s (64-bit/66MHz) One 64-bit wide PCI-Xbus with 66MHz One 32-bit wide PCIbus with 33MHz Data throughout between 855GME and 6300ESB is 256 MB/s (theoretical)
Communications Controller
114 Kbytes non-volatile CMOS-RAM for BIOS data
CompactPCI Interface Compliance standards
PICMG 2.0 R3.0 compliant CPCI 32bit/33MHz local bus standard Backplane with rear I/O System only PCI bridge TI PCI2050B for up to 7 slots J1+2, 2mm pin and socket connectors (IEC-1076-4-101)
EIDE
Ultra ATA/100 sync. DMA mode up to 90 Mbytes/s PIO mode 4 and bus master IDE up to 16 Mbytes/s Onboard devices supported via local header
Environmental
Temperature: Note: For detailed information about the opening temperature behavior of the board is absolutely necessary to consult the manual. The highest achievable operating temperature depends on processor type, speed, ambient conditions (air flow) and front plate width. All values under typical conditions Operating Storage Standard 0C to +70C -40C to +85C Extended -40C to +75C -40C to +85C Humidity: Operating: 5-95%@40C Storage: 5-95%@40C Altitude: Operating: 15,000 ft. (4.5km) Storage: 40,000 ft. (12km) Shock: C-, I-. Style 12g/6ms, 3 axis, up & down, 5 hits/direction Vibration: C-, I-.Style 2g rms@5 to 100Hz, 30 minutes each axis
External Card
Via USB port
Flash Memory
EIDE interface on header connector for two devices Extension board with one CompactFlash connector (4HP) On extension card (8HP) for one 2.5" IDE hard disk or one Compact Flash connector (for extended temperature range and higher shock/vibration immunity)
GPIO
Highly integrated Dual Ethernet Controller with 64-bit/66MHz PCI-X local bus DMA 64 Kbyte Transmit and recieve FIFO 10/100/1000BaseT auto-negotiation Both channels at front I/O with RJ45 connectors and status LEDs
Graphic Processor
8 bit programmable general purpsoe input/outpus
Keyboard/Mouse
Via USB (supports legacy keyboard/mouse SW)
Mechanical
3U, 1 slot wide (100x160x20.32mm) with 4HP front panel 3U, 2 slot wide (100x160x40.64mm) with 4HP front panel CL9 at backplanes with right justified system slot occupies one CPCI slot only
Memory
High-speed 333MHz (PC2700) DDR SDRAM 64-bits wide 512Mbytes to 1 Gbyte with soldered chips
MTBF
Calculations are available in accordance with MIL-HDBK-217.
Power Consumption
Typical operating current (estimated) 512MB memory bank, w/o keyboard, hard disk, modules, etc. Pentium M 5V 3.3V Total Power 1.0GHz A A W Celeron M 1.3GHz A A W Celeron M 1.4 A A W 1.6 GHz 3.7A 2.4A 26.5W 1.8 GHz 2.9A 2.4A 22.5W Operating measured at DOS prompt, no power saving
Power Requirements
+5V, 3.3V Required
Processor
Intel Pentium M
Scaleable processing power with flexible processor design
Intel Pentium M processor: 1.4GHz to 1.8GHz
Intel Celeron M processor: 1.0GHz and 1.3 GHz
High efficiency on-board switching regulator (DC/DC)
Fanless cooling with heat sink
RTC
Integrated in chipset RTC 146818 compatible, on-board-li battery
Safety Criteria
Designed to meet standard UL 1590, CE Class A, FCC-A
Serial
Integrated in chipset Two asnyc. 16550 compatible full-duplex serial channels High-speed transfer up to 115.2 kbaud with 16 byte FIFO's COM1 and COM2 optional avaiable at front (8HP) or rear I/O With 8HP extension card other interface types are supported (eg. RS485
USB
Four USB 2.0 connectors, one or two (8HP) on front and two on rear I/O
VGA
2D & 3D graphics engine Up to 64MB of dynamic video memory allocation Integrated 350Mhz 24-bit RAMDAC for analog VGA monitors up to 1600x1024, 75Hz Integrated Digital Video Output (DVO) Port interface Dual independant pipe support Display image rotation Graphics Power Managament VGA at front and rear I/O DVO at connector, with extension card DVI-D support possible
Features
- 2x serial I/O with FIFOs RS-232 interface
- 3U CompactPCI in single or double slot
- 4x USB 2.0
- 5V / 3.3V supply
- CGA/DVO interface
- Custom specific versions
- Dual Gigabit Ethernet
- Dual Serial ATA interfaces
- Enhanced IDE UDMA-100
- Flash drive up to 4GB or local 2.5" hard disk
- Intel® Pentium® M processor, 600 MHz to 1.8 GHz
- Optional -40°C to +75°C
- Optional audio interface
- System slot for 32 bit CompactPCI backplane
- Two Gigabit Ethernet ports
- Ultra compact all-in-one PC
- Up to 1Gb DDR SDRAM
- Up to 2MB L2 cache
- Watchdog, temperature sensor
Datasheet
GE Intelligent Platforms-CL9-datasheet.pdf
598 KiB
Extracted Text
CL9 ® High Performance – 3U CompactPCI Intel® Pentium® M Processor Board Features ® ® • Intel Pentium M processor, ® 1.4 GHz to 1.8 GHz and Intel ® Celeron M processor 1.0 GHz and 1.3 GHz • Up to 2MB L2 cache • Ultra compact all-in-one PC • System slot for 32-bit CompactPCI backplane • Up to 1GB DDR SDRAM • Flash drive up to 4 GB or local 2.5” hard disk • VGA/DVO interface Single slot version not shown • Dual Gigabit Ethernet ® • Enhanced IDE UDMA-100 CL9 is a high-performance 3U CompactPCI CPU board using the low power â â Intel Pentium M Processor incorporating sophisticated power management • Dual Serial ATA technology, eliminating the need for an onboard fan. The CL9 is available in two different front options (1 or 2 slot width), enabling the user to select the feature set • 2x serial I/O with FIFOs required for the target application. The CL9 runs in the system slot of the RS-232 interface CompactPCI backplane. • 4x USB 2.0 The single slot version contains a CompactFlash as an option. The 8HP version optionally contains an integrated hard disk or CompactFlash. The • Optional audio interface 8HP versions offer the user the choice between a DVI interface or a COM2 port on • Watchdog, temperature the front. In place of the COM1an audio interface AC’97 can be integrated if the operating temperature is not below 0 °C. sensor The CL9 supports two Gigabit Ethernets, up to 1 Gbyte of DDR SDRAM and • 5V / 3.3V supply supports VGA/DVO. At the core of the CL9 design is a high-bandwidth bus between the processor and the chipset running at 400MHz bus. The chipset-to-memory bus • Optional -40°C to +75°C supports 333 MHz (PC2700) DDR SDRAMs. In addition there are four USB 2.0 ports, two serial channels, and two serial ATA channels. Interfaces are available as front- and/or rear-I/O. The CL9 is available in standard temperature range 0° to +70°C, and • Custom specific versions optional in extended from -40°C to +75°C. Custom specific versions are available on request. The CL9 is a powerful processor platform for a wide range of applications and markets such as multimedia, automation, transportation, as well as imaging, medical, robotics, and many others. The CL9 is very suited to low-power embedded computer applications in a small form factor where optimal performance and functionality is required. Single Board Computers Specifications Serial I/O - RS232 · Integrated in chipset · Two async. 16550 compatible full duplex serial channels Processor - µFCBGA, Low Power design · High-speed transfer up to 115.2 kbaud with 16 byte FIFOs · Scaleable processing power with flexible processor design · COM1 and COM2 optional available at front (8HP) or rear I/O · Intel Pentium M processor: 1.4 GHz to 1.8 GHz · With 8HP extension card other interface types are supported · Intel Celeron M processor: 1.0 GHZ and 1.3 GHz (e.g. RS485) · High efficiency on-board switching regulator (DC/DC) · Fanless cooling with heat sink Audio AC’97 Interface - optional · See price list for latest CPU versions · S/PDIF digital output (optical) · Line in Cache level 1 level 2 · Headphone out Pentium M (90nm) 32 KB 2MByte, full speed · Note: The audio interface does not operate below 0 °C Pentium M (130nm) 32 KB 1MByte, full speed Celeron M (130nm) 32 KB 1MByte, full speed General Purpose Input/Outputs Celeron M (90nm) 32 KB 512KByte, full speed · 8 bits programmable general purpose inputs/outputs Chipset – Intel 855GME with 6300ESB USB 2.0 · 400 MHz system bus to processor · Four USB 2.0 connectors, one or two (8HP) on front and two · PCI burst mode transfers up to 512 MB/s (64-bit/66 MHz) on rear I/O · One 64-bit wide PCI-Xbus with 66 MHz · One 32-bit wide PCIbus with 33 MHz Keyboard · Data throughput between 855GME and 6300ESB is 256 MB/s · Via USB (supports legacy keyboard/mouse SW) (theoretical) Mouse Memory – DDR 333 · Via USB (supports legacy keyboard/mouse SW) · High-speed 333MHz (PC2700) DDR SDRAM · 64-bits wide Real-time clock · 512 Mbytes to 1 Gbyte with soldered chips · Integrated in chipset · RTC 146818 compatible, on-board Li-battery CompactPCI · PICMG 2.0 R3.0 compliant CPCI 32bit/33MHz local bus CMOS RAM standard · 114 bytes non-volatile CMOS RAM for BIOS data · Backplane with rear I/O · System only PCI Bridge TI PCI2050B for up to 7 slots EEPROM · J1+2, 2 mm pin and socket connectors (IEC-1076-4-101) · 1Mbit (128kByte) serial EEPROM for non-volatile user data Gigabit – Intel 82546GB Floppy · Highly integrated Dual Ethernet Controller with 64-bit/66 MHz · Via USB port PCI-X local bus DMA · 64 Kbyte Transmit and Receive FIFO Watchdog · 10/100/1000BaseT auto-negotiation · Integrated in chipset · Both channels at front I/O with RJ45 connectors and status · Two stage watchdog with independent count values LEDs · First stage drives NMI or SMI, second stage drives reset · Configurable granularity from 1ms to 10min Hard Disk or Flash Drive · EIDE interface on header connector for two devices Timer · Extension board with one Compact Flash connector (4HP) · Integrated in chipset based on 82C59 · On extension card (8HP) for one 2.5” IDE hard disk or one · Includes three timer comparators Compact Flash connectors (for extended temperature range · One-shot and periodic interrupts supported and higher shock/vibration immunity) Temp. Sensor VGA and LCD - Chipset Integrated · CPU die and heat sink temperature software readable from · 2D & 3D graphics engine –65°C to +127°C · Up to 64MB of dynamic video memory allocation · Integrated 350MHz 24-bit RAMDAC for analog VGA monitors LED up to 1600 x 1024, 75Hz · Two LEDs at front panel · Integrated Digital Video Output (DVO) Port interface · Dual independent pipe support BIOS Features · Display image rotation · New AMI BIOS Core 8, in-system programmable Flash ROM · Graphics power management · CPU, memory and IDE auto-detection/selection · VGA at front and rear I/O · Integrated VGA, and Ethernet BIOS ROM · DVO at connector, with extension card DVI-D support possible · USB Mass Storage support · Password protection, BIOS post, system and video BIOS EIDE shadowing · Ultra ATA/100 sync. DMA mode up to 90 Mbytes/sec · Extensive setup with remapable serial/parallel ports · PIO mode 4 and bus master IDE up to 16 Mbytes/sec · Operation without disk and keyboard · Onboard devices supported via local header · Remote BIOS through serial port SATA Power Requirements Software · +5 V, +3.3V Required · The following software is supported to the extent listed below. Power Consumption - typical operating current (estimated) · 512 MB memory bank, w/o keyboard, hard disk, modules, etc. OS On Request Available WIN XP - Ö Pentium M 5 V 3.3 V Total Power QNX 6 Ö - 1.0 GHz A A W Celeron M VxWorks - Ö 1.3 GHz A A W Celeron M Lynx OS Ö - 1.4 GHz A A W Linux - Ö 1.6 GHz 3.7 A 2.4 A 26.5 W 1.8 GHz 2.9 A 2.4 A 22.5 W Front and Onboard I/O With standard Front Panel (8HP) Operating measured at DOS prompt, no power saving Mechanical – PICMG 2.0 Function Front I/O On-board I/O Rear · 3U, 1 slot wide (100 x 160 x 20.32mm) with 4HP Front panel I/O · 3U, 2 slot wide (100 x 160 x 40.64mm) with 8HP Front panel Giga Ethernet 0 RJ-45 · CL9 at backplanes with right justified system slot occupies Giga Ethernet 1 RJ-45 one CPCI slot only. USB 0 USB USB 1 USB Temperature USB 2/3 yes · Note: For detailed information about the operating temperature VGA D-15 yes *1 behavior of the board it is absolutely necessary to consult the DVO DVI-D manual. The highest achievable operating temperature EIDE yes depends on processor type, speed, ambient conditions (air SATA 1 yes flow) and front plate width. SATA 2 yes · All values under typical conditions. COM 1 D-09 yes COM 2 D-09 yes Operating Storage *2 Audio AC’97 Yes Standard 0°C to +70°C –40°C to +85°C GPIO (8 pins) yes Extended -40°C to +75°C –40°C to +85°C Reset Button yes Speaker Yes Humidity LED Yes · Operating: 5 - 95% @ 40°C Keyboard, Via USB Via · Storage: 5 - 95% @ 40°C mouse, Floppy USB *1 Possible with special extension card, COM2 front I/O not Altitude available · Operating: 15.000 ft. (4.5 km) *2 Only available for operating temperature range ≥ 0 °C · Storage: 40.000 ft. (12 km) Front and Onboard I/O Shock With standard Front Panel (4HP) · C-, I-.Style 12g / 6 ms, 3 axis, up & down, 5 hits / direction Function Front I/O On-board I/O Rear Vibration I/O · C-, I-.Style 2 g rms @ 5 to 100 Hz, 30 minutes each axis Giga Ethernet 0 RJ-45 MTBF Giga Ethernet 1 RJ-45 · Calculations are available in accordance with MIL-HDBK-217. USB 0 USB Please contact factory. USB 1 Header USB 2/3 Yes Safety VGA D-15 Yes · Designed to meet standard UL 1590, CE class A, FCC-A DVO Header EIDE Header SATA 1 Yes SATA 2 Yes COM 1 Header Yes COM 2 Header Yes GPIO (8 pins) Yes Reset Button Yes Speaker Yes LED Yes Keyboard, Via USB Via mouse, Floppy USB CL9 Block Diagram Intel® Pentium®M Processor Intel® VGA / 1 GB DDR 855GME LCD SDRAM VGA / LCD 266 MB/s CPCI 2x GbE Bridge 2x SATA 2x COM Intel® 6300ESB 1x EIDE 4x USB Watchdog AC’97 Timer RTC, GPIO SMB Ordering Information Hardware Accessories CTM15: I/O transition module for 3U backplane SCC484TC08CL9: Starter cage 19” 4U with fans, power supply, CDROM and hard disk Operating Systems Extensive operating systems support is available (see page 3). Chassis with power supplies, backplanes and drives on request. For detailed information and further options, contact SBS. Corporate Headquarters European Headquarters 7401 Snaproll NE Memminger Str. 14 Albuquerque, NM 87109 D-86159 Augsburg, Germany Tel 505.875.0600 Fax 505.875.0400 Tel +49-821-5034-0 Fax +49-821-5034-119 Email info@sbs.com Email aug-info@sbs.com For additional contact information, please visit our web site at www.sbs.com Specifications subject to change without notice. All trademarks and logos are property of their respective owners. ©2006 SBS Technologies, Inc. 20060627
Frequently asked questions
How does Industrial Trading differ from its competitors?
Is there a warranty for the CL9?
Which carrier will Industrial Trading use to ship my parts?
Can I buy parts from Industrial Trading if I am outside the USA?
Which payment methods does Industrial Trading accept?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Related Products
GE Intelligent Platform A16B-2200-0521 CPU Board - GE FANUC Series 15i - BASE 0 (Serial Spindle), Co...
GE INTELLIGENT PLATFORMS ACC-0602RC-000 CPU Boards - Rear Transition Module (RTM) designed to transi...
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods