GE INTELLIGENT PLATFORMS CC11
Description
High Performance - 3U CompactPCI Dual Slot Dual Core Processor Board
Part Number
CC11
Price
Request Quote
Manufacturer
GE INTELLIGENT PLATFORMS
Lead Time
Request Quote
Category
Single Board Computers
Specifications
Form Factor
PICMG
Ethernet Chipset
Realtek RTL8111B
System Chipset
Intel 945G
Video Chipset
Intel 945GM
Audio
S/PDIF digital output (optical) Line in Headphone out
Cache
Cache Level 1 Level 2 Core Duo 32 KB 2 MB, full speed Core 2 Duo 32 KB 4 MB, full speed
Chipset
533/667 MHz system bus to processor One PCI Express x4 or four PCI Express x1 interfaces Two PCI Express x1 interfaces Data throughput between 945GM and ICH7R is theoretically 2 GB/s (1 GB/s each direction)
Communications Controller
114 bytes non-volatile CMOS RAM for BIOS data
CompactPCI Interface Compliance standards
PICMG 2.0 R3.0 compliant CPCI 32bit/66 MHz local bus standard Backplane with rear I/O System or non-system (peripheral) PCI Bridge Pericom PI7C9X110 for up to 7 slots J1+2, 2 mm pin and socket connectors (IEC-1076-4-101)
EIDE
Ultra ATA/100 sync. DMA mode up to 90 MB/s PIO mode 4 and bus master IDE up to 16 MB/s Onboard devices supported via local header
EPROM
512 Kbit (64 KB) serial EEPROM for non-volatile user data
External Card
Via USB port
Flash Memory
EIDE and SATA interfaces on header connector One 2.5" SATA/EIDE hard disk or one Compact Flash connector (for extended temperature range and higher shock/vibration immunity)
GPIO
Highly integrated Single Gigabit Ethernet Controller with PCI Express x1 interface 64 KB Transmit and Receive FIFO 10/100/1000BaseT auto-negotiation Port 1 and Port 2 for front or rear I/O. Solder option. Port 3 and Port 4 for front I/O. Depends on product version
Graphic Processor
Integrated in SMSC SCH3112 Super I/O 8 bits programmable general purpose inputs/outputs
Keyboard/Mouse
Via USB (supports legacy keyboard/mouse SW)
Memory
Single-/Dual-Channel DDR2 SDRAM High-speed 667 MHz (PC2 5300) DDR2 SDRAM 64-bits wide / 128-bits wide 512 MB to 2 GB with soldered chips
Networking
RTC: Integrated in chipset RTC 146818 compatible, on-board Li-battery Watchdog: Integrated in chipset Two stage watchdog with independent count values First stage drives NMI or SMI, second stage drives reset Configurable granularity from 1 µs to 10 min
Processor
Intel Core Duo
Scaleable processing power with flexible processor design
Intel Core Duo processor U2500: 1.20 GHz
Intel Core Duo processor L2400: 1.66 GHz
Intel Core Duo processor T2500: 2.00 GHz
Intel Core 2 Duo processor L7400: 1.5 GHz
High efficiency on-board switching regulator (DC/DC)
Fanless cooling with heat sink
SATA
Two serial ATA at rear I/O One SATA interface on header connector DMA mode up to 150 MB/s
Serial
Integrated in SMSC SCH3112 Super I/O Two async. 16550 compatible full duplex serial channels High-speed transfer up to 115.2 kbaud with 16 byte FIFOs COM1 available at rear I/O COM2 optional available at front (8 HP) COM2 interface supports RS232, opto RS232/485
Timer
Integrated in chipset based on 82C59 Includes three timer comparators One-shot and periodic interrupts supported
USB
Six USB 2.0 connectors. Three on front, three on rear I/O.
VGA
2D & 3D graphics engine DirectX 9.1 support Up to 64 MB of dynamic video memory allocation Integrated 360 MHz 24-bit RAMDAC for analog VGA monitors up to 1600 x 1200, 75 Hz Display image rotation Graphics power management VGA at front or rear I/O SDVO at connector, with extension card DVI-D support possible
Features
- 2x serial I/O with FIFOs, RS-232 interface
- 3x Serial ATA
- 5 V / 3.3 V supply
- 6x USB 2.0
- Enhanced IDE UDMA-100
- Flash drive or local hard disk
- Intel® Core 2 Duo® processor, 1.5 GHz Intel® Core Duo® processor 1.2, 1.66 and 2 GHz
- Optional –40° C to +75° C
- Optional audio interface
- RoHS compliant
- System or Non-system (peripheral mode)
- System slot for 32-bit CompactPCI backplane
- Ultra compact all-in-one PC
- Up to 2 GB DDR2 SDRAM
- Up to 4 MB L2 cache
- Up to four Gigabit Ethernet ports
- VGA interface/SDVO interface
- Watchdog, temperature sensor
Datasheet
GE Intelligent Platforms-CC11-datasheet.pdf
918 KiB
Extracted Text
GE Intelligent Platforms CC11 High Performance - 3U CompactPCI Dual Slot Dual Core Processor Board Features CC11 is a high-performance 3U CompactPCI The CC11 standard temperature range is ® ® CPU board using the Intel Core Duo or the from 0° C to +50° C. The optional extended • Intel Core 2 Duo processor, 1.5 GHz ® ® Intel Core 2 Duo Processor incorporating temperature starts at -40° C. The upper Intel Core Duo processor 1.2, 1.66 sophisticated power management technol- temperature depends on the selected and 2.16 GHz ogy, eliminating the need for an onboard processor type an available air flow in the • Up to 4 MByte L2 cache fan. The CC11 can be ordered as a system or system. For example. the 1/06GHz ULV Cel- • Ultra compact all-in-one PC non-system slot single board computer. eron M 423 processor is able to achieve a † maximum temperature of 85° C with 3m/s • System or non-system (peripheral mode) CompactFlash is available as an option. airflow. Custom specific versions are avail- ® • System slot for 32-bit CompactPCI able on request. backplane It contains an integrated SATA or EIDE hard • Up to 2 GByte DDR2 SDRAM disk or CompactFlash. It offers the user The CC11 is a powerful processor platform the choice between a DVI interface or a • Flash drive or local hard disk for a wide range of applications and mar- COM2 port on the front. In place of the dual kets such as multimedia, automation, • VGA interface/SDVO interface Ethernet ports an audio interface can be transportation, as well as imaging, medical, • Up to four Gigabit Ethernet ports available based on an order option. robotics, and many others. The CC11 is very • Enhanced IDE UDMA-100 suited to low-power embedded computer The CC11 supports up to four Gigabit applications in a small form factor where • 3x Serial ATA Ethernets, up to 2 GByte of DDR2 SDRAM optimal performance and functionality is • 2x serial I/O with FIFOs, RS-232 interface and VGA/SDVO. At the heart of the CC11 required. • 6x USB 2.0 design is a high-bandwidth 667MHz bus connecting the processor, chipset and • Optional audio interface The CC11 is RoHS compliant. PC2-5300 DDR2 SDRAM. In addition there • Watchdog, temperature sensor are six USB 2.0 ports, two serial channels, For a single slot 3U CompactPCI SBC, refer • 5 V/3.3 V supply and three serial ATA channels. Interfaces to the CL11 dual core processor board. • Optional –40° C to +85° C are available as front- and/or rear-I/O. • RoHS compliant † For non-system (peripheral mode) please contact GE Intelligent Platforms. CC11 High Performance - 3U CompactPCI Dual Slot Dual Core Processor Board SATA Software Specifications • Two serial ATA at rear I/O • The following software is supported to the extent Processor - µFCBGA, Low Power Design • One SATA interface on header connector listed below. • Scaleable processing power with flexible • DMA mode up to 150 MByte/s OS On Request Available processor design Serial I/O - RS232 ® • Intel Core Duo processor U2500: 1.20 GHz Windows XP - √ • Integrated in SMSC SCH3112 Super I/O • Intel Core Duo processor L2400: 1.66 GHz Windows XP - √ • Two asynchronous 16550 compatible full duplex • Intel Core Duo processor T7400: 2.16 GHz serial channels Embedded • Intel Core 2 Duo processor L7400: 1.5 GHz • High-speed transfer up to 115.2 kbaud with • High efficiency on-board switching regulator (DC/DC) QNX 6 √ - 16 byte FIFOs • Fanless cooling with heat sink ® • COM1 available at rear I/O VxWorks - √ * Contact factory for latest CPU versions • COM2 optional available at front (8 HP) ® Linux - √ Cache Level 1 Level 2e • COM2 interface supports RS232, opto RS232/485 Core Duo 32 KByte 2 MByte, full speed Audio Interface - optional Front and Rear I/O with Standard Front Panel • S/PDIF digital output (optical) Core 2 Duo 32 KByte 4 MByte, full speed Function Single Board Computer CC11 • Line in • Headphone out Front Onboard Rear Chipset – Intel 945GM with Intel ICH7R I/O I/O I/O General Purpose Input/Outputs • 533/667 MHz system bus to processor • Integrated in SMSC SCH3112 Super I/O • One PCI Express x4 or four PCI Express x1 interfaces 1 1,4 Gb Ethernet 0R J-45 * Yes * • 8 bits programmable general purpose inputs/outputs • Two PCI Express x1 interfaces 1 1,4 • Data throughput between 945GM and ICH7R is Gb Ethernet 1 RJ-45 * Yes* USB 2.0 theoretically 2 GByte/s (1 GByte/s each direction) • Six USB 2.0 connectors. Three on front, three USB 0 USB on rear I/O. Memory – DDR2 667 USB 1 USB • Single-/dual-channel DDR2 SDRAM Keyboard • High-speed 667 MHz (PC2 5300) DDR2 SDRAM USB 2 to 4 Yes • Via USB (supports legacy keyboard/mouse SW) • 64-bits wide/128-bits wide VGA D-15 D-15 Mouse • 512 MByte to 2 GByte with soldered chips • Via USB (supports legacy keyboard/mouse SW) EIDE Misc. Header CompactPCI Real-time Clock SATA 1 / 2 Yes • PICMG 2.0 R3.0 compliant CPCI 32 bit/66 MHz • Integrated in chipset local bus standard COM 1 Yes • RTC 146818 compatible, on-board Li-battery • Backplane with rear I/O GPIO (8 pins) Yes † • System or non-system (peripheral) PCI Bridge CMOS RAM Pericom PI7C9X110 for up to 7 slots • 114 bytes non-volatile CMOS RAM for BIOS data Power button Button • J1+2, 2 mm pin and socket connectors EEPROM Reset Yes (IEC-1076-4-101) • 512 Kbit (64 KByte) serial EEPROM for non-volatile Speaker Yes Gigabit – Realtek RTL8111B user data • Highly integrated Single Gigabit Ethernet Controller LED Yes Floppy with PCI Express x1 interface • Via USB port Keyboard, • 64 KByte Transmit and Receive FIFO Mouse, Floppy Via USB Via USB • 10/100/1000BaseT auto-negotiation Watchdog • Port 1 and Port 2 for front or rear I/O. Solder option. • Integrated in chipset USB 5 USB • Port 3 and Port 4 for front I/O. Depends on • Two-stage watchdog with independent count values 2 SDVO DVI-D * product version. • First stage drives NMI or SMI, second stage EIDE HDD or CFlash drives reset Hard Disk or Flash Drive • Configurable granularity from 1 μs to 10 min Connector • EIDE and SATA interfaces on header connector • One 2.5" SATA/EIDE hard disk or one Compact Flash Timer SATA 3 HDD Connector connector (for extended temperature range and • Integrated in chipset based on 82C59 higher shock/vibration immunity) COM 2 D-9 • Includes three timer comparators VGA and LCD - Chipset Integrated • One-shot and periodic interrupts supported Gb Ethernet 2 RJ-45 • 2D & 3D graphics engine Temperature Sensor Gb Ethernet 3 RJ-45 • DirectX 9.1 support • CPU die and heat sink temperature software read- 3 Audio I/F * Line Out • Up to 64 MByte of dynamic video memory allocation able from –65° C to +127° C • Integrated 360 MHz 24-bit RAMDAC for analog VGA Line In monitors up to 1600 x 1200, 75 Hz LED S/PDIF • Display image rotation • Two LEDs at front panel Out • Graphics power management BIOS Features Speaker Yes • VGA at front or rear I/O • New AMI BIOS Core 8, in-system programmable • SDVO at connector, with extension card DVI-D 1 Flash ROM * Front- or Rear-IO as a solder option support up to 1600 x 1200, 60 Hz possible 2 • Automatic system configuration * Possible with special extension card, COM2 front I/O not available EIDE • Integrated VGA, SATA RAID and Ethernet PXE ROM 3 • Ultra ATA/100 sync. DMA mode up to 90 MByte/s * Only available for operating temperature ≥ 0 °C • USB mass storage support 4 • PIO mode 4 and bus master IDE up to 16 MByte/s * Ethernet ports on the rear are not available on the • Password protection CTM18 transition module • Onboard devices supported via local header • Headless support • Remote console through serial port †For non-system (peripheral mode) please contact GE Intelligent Platforms. CC11 High Performance - 3U CompactPCI Dual Slot Dual Core Processor Board Specifications (cont.) Block Diagram Power Requirements • +5 V, +3.3 V Required Intel Core 2 Duo Power Consumption - typical operating current (est) Processor • TBD ® Mechanical – PICMG 2.0 • 3U, 2 slot wide (100 x 160 x 40.64) mm with VGA Intel 8HP Front panel 945GM 2 GByte DDR 2 VGA/LCD • CC11 in backplanes with right justified system slot DVI-D SDRAM occupies one CPCI slot only. 2 Gbyte/s Temperature PCI-E • Note: For detailed information about the operating 1x EIDE GbE Controller 1x GbE Intel (x1) temperature behavior of the board it is absolutely ICH7R PCI-E necessary to consult the manual. The highest GbE Controller 1x GbE 3x SATA (x1) achievable operating temperature depends on processor type, speed, ambient conditions (air flow) PCI-E CPCI Bridge (x1) and front plate width. 6x USB • All values under typical conditions. Codec Audio Watchdog Operating Storage Timer 2x COM RTC LPC * Standard 0° C to +50° C –40° C to +85° C Super I/O SMB 8x GPI/O ** Extended –40° C to +85° C –40° C to +85° C PCI-E * Consult the manual for the required airflow and other basic 1x GbE GbE Controller (x1) conditions. PCI-E ** The maximum achievable temperature is a function of 1x GbE GbE Controller (x1) the selected CPU version, air flow, altitude, etc. Not every processor is able to achieve this maximum temperature. Please consult the manual for detailed information. Humidity • Operating: 5% – 95% @ 40° C Ordering Information • Storage: 5% – 95% @ 40° C Hardware Accessories Altitude CTM18A01 I/O transition module for 3U backplane • Operating: 15,000 ft. (4.5 km) SCC484TB05CC11R Starter cage 19" 4U, 5 slots, with fans, power supply, DVD, hard disk, transition module, • Storage: 40,000 ft. (12 km) 0° C to +40° C Shock (3 axis, up & down, 5 hits/direction) Operating Systems • Styles 1, 3: 12g / 6 ms Extensive operating systems support is available (see page 3). Chassis with power supplies, backplanes and drives Vibration (60 minutes each axis) on request. For detailed information and further options, contact GE Intelligent Platforms • Styles 1, 3: 2g rms @ 5 to 100 Hz Software VITA 47 CL11-SDK-Linux System Development Kit for CC11/CL11 Linux • Designed to meet VITA47 class EAC1 and EAC3 CC11-BSP-VXW VxWorks 6.6 Board Support Package for CC11/CL11 MTBF CL11-SDK-XP System Development Kit for CC11/CL11 for Windows XP and XP Embedded. • Calculations are available in accordance with MIL-HDBK-217. Please contact GE Intelligent Platforms. Safety • Designed to meet standard UL1590, About GE Intelligent Platforms CE Class A, FCC-A GE Intelligent Platforms, a General Electric Company (NYSE: GE), is an experienced high-performance technology company and a global provider of hardware, software, services, and expertise in automation and embedded computing. We offer a unique foundation of agile, advanced and ultra-reliable technology that provides customers a sustainable advantage in the industries they serve, including energy, water, consumer packaged goods, government and defense, and telecommunications. GE Intelligent Platforms is a worldwide company headquartered in Charlottesville, VA and is part of GE Home and Business Solutions. For more information, visit www.ge-ip.com. GE Intelligent Platforms Contact Information Americas: 1 800 433 2682 or 1 434 978 5100 Global regional phone numbers are listed by location on our web site at www.ge-ip.com/contact www.ge-ip.com ©2011 GE Intelligent Platforms, Inc. All rights reserved. All other brands or names are property of their respective holders. Specifications are subject to change without notice. 05.11 GFA-996A
Frequently asked questions
How does Industrial Trading differ from its competitors?
Is there a warranty for the CC11?
Which carrier will Industrial Trading use to ship my parts?
Can I buy parts from Industrial Trading if I am outside the USA?
Which payment methods does Industrial Trading accept?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Related Products
GE Intelligent Platform A16B-2200-0521 CPU Board - GE FANUC Series 15i - BASE 0 (Serial Spindle), Co...
GE INTELLIGENT PLATFORMS ACC-0602RC-000 CPU Boards - Rear Transition Module (RTM) designed to transi...
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods