Datasheet DM3 Media Boards ® Dialogic DM3 Media Boards ® The Dialogic DM3 Media Boards are an integral part of many high-density media server solutions. They provide voice processing and many other standard features including tone signaling, global tone detection, global tone generation, and call progress analysis. These boards are well-suited for many conŢgurations and applications where enhanced media such as speech recognition, fax, and conferencing are ® not required. These boards can also be combined with other Dialogic boards (switching, fax, or combined media) to provide enhanced media resources in a single system, thereby providing signiŢcant cost savings. Products Discussed in This Datasheet ® ® • Dialogic DM/V480-4T1 Voice Board • Dialogic DM/V1200-4E1 Voice Board ® ® • Dialogic DM/V960-4T1 Voice Board • Dialogic DM/V600-4E1 Voice Board Because the boards are available in both H.100 (PCI) and H.110 (CompactPCI) compliant universal form factors, they are excellent for service providers and large enterprise applications. This ţexibility lets developers build single applications for deployment on either industry-standard form factor. Each board provides access to four T-1 (1.544 Mb/s) or E-1 (2.048 Mb/s) digital network interfaces, and up to 120 ports of voice and telephony signal processing. Features Benefits Four T-1 or E-1 digital network interfaces with internationally Lets applications connect to a variety of signaling networks approved CAS and ISDN PRI worldwide, facilitating faster time-to-market with global deployment Available with either full- or half-density voice resources Offers ability to choose different boards with either 1:1 or 1:2 voice to network interface ratio, which may be suitable in certain environments such as inbound call centers, providing fewer wasted resources and considerable board savings Built on the industry-standard telephony bus — ECTF Lets applications expand through access to other H.100/H.110 CT Bus communication boards, such as IP telephony, ATM, HDSI, and SS7, as well as combined media resource boards such ® as the Dialogic DM/V3600BP Media Board ® Datasheet Dialogic DM3 Media Boards Technical Specifications Maximum boards per system Application, call trafŢc, and CPU dependent CT Bus PCI: ECTF H.100 compliant CT Bus, offering onboard switching access to 4096 bidirectional 64 kb/s DS-0 time slots SCbus interoperability through adapter 68-pin ribbon cable connector CompactPCI: ECTF H.110 compliant CT Bus, offering onboard switching access to 4096 bidirectional 64 kb/s DS-0 time slots Digital interfaces 4 T-1 or 4 E-1 Control processor Intel i960C Digital signal processors PCI and CompactPCI: Motorola 56303; 6 DSPs @ 100 MHz each Control processor memory 8 MB DSP memory PCI and CompactPCI: 256 K word DRAM local to each DSP 128 K word SRAM local to each DSP Baseboard global memory 32-bit wide DRAM accessible to all signal processors and control processor Cache prompts 4 MB to 8 MB ® Supported operating systems Windows ; Linux. Details at http://www.dialogic.com/systemreleases CSP No Signaling ISDN PRI CAS robbed-bit (T1); R2MF (E1) Host Interface Bus compatibility PCI: Rev 2.2 of PCI Bus SpeciŢcation CompactPCI: Rev 2.1 of PCI Bus SpeciŢcation Bus mode Target and DMA master mode operation Host interface memory 512 KB Support 3.3 V or 5 V signaling environment (universal connectivity) Platforms Form factors PCI: Universal PCI long card, single-slot width 12.3 in. (31.24 cm) long (without edge retainer) or 13.3 in. (33.78 cm) long (with edge retainer) 0.79 in. (2 cm) wide (total envelope) 3.87 in. (9.83 cm) high (excluding edge connector) CompactPCI: 6U Eurocard form factor, single-slot width PBA, including faceplate, handles, and connectors 10.43 (265) mm long 8.27 in. (210 mm) wide .79 in. (20 mm) high Network connectors PCI: 4 RJ-48C on rear bracket CompactPCI: Provided through rear I/O transition modules (not included with board) BNC for 75 Ohm lines RJ-48C for 100 Ohm and 120 Ohm lines Power Requirements PCI ConŢguration +5 VDC +12 VDC –12 VDC +3.3 VDC DM/V960-4T1-PCI 19.25 W 0.360 W N/A N/A DM/V1200-4E1-PCI 19.25 W 0.360 W N/A N/A DM/V480-4T1-PCI 19.25 W 0.360 W N/A N/A DM/V600-4E1-PCI 19.25 W 0.360 W N/A N/A Compact PCI ConŢguration +5 VDC +12 VDC –12 VDC +3.3 VDC DM/V960-4T1-cPCI 19.34 W 1.1 W N/A 2.04 W DM/V1200-4E1-cPCI 19.34 W 1.1 W N/A 2.04 W DM/V480-4T1-cPCI 19.34 W 1.1 W N/A 2.04 W DM/V600-4E1-cPCI 19.34 W 1.1 W N/A 2.04 W 2 ® Dialogic DM3 Media Boards Datasheet Technical Specifications (cont.) Environmental Requirements PCI and CompactPCI Operating temperature +32°F (0°C) to +122°F (+50°C) Cooling condition per maximum +122°F (+50°C) — 2.3 CFM per board operating temperature +104°F (+40°C) — 1.5 CFM per board +86°F (+30°C) — 1.1 CFM per board Storage temperature –4°F (–20°C) to +158°F (+70°C) Humidity 8% to 80% noncondensing Telephone Interface DSX-1 T-1 Clock rate 1.544 Mb/s ±32 ppm Level 3.0 V (nominal) Pulse width 323.85 ns (nominal) Line impedance 100 Ohm ±10% Other electrical characteristics Complies with AT&T TR62411 and ANSI T1.403-1989 Framing SF (D3/D4) ESF for ISDN Line coding AMI AMI with B7 stufŢng B8ZS Clock and data recovery Complies with AT&T TR62411 and Telcordia TA-TSY-000170 Jitter tolerance Complies with AT&T TR62411 and ANSI T1.403-1989 Connectors RJ-48C Telephony bus connector H.100 (PCI) and H.110 (CompactPCI) style connectors Loopback Supports switch-selectable local analog loopback and software selectable local digital loopback Zero code suppression Bell ZCS (Jam bit 7) GTE ZCS (Jam bit 8) Digital Data Service ZCS No zero code suppression Telephone Interface CEPT E-1 Network clock rate 2.048 Mb/s ±50 ppm Internal clock rate 2.048 Mb/s ±32 ppm Level 2.37 V (nominal) for 75 Ohm lines 3.0 V (nominal) for 120 Ohm lines Pulse width 244 ns (nominal) Line impedance 75 Ohm, unbalanced 120 Ohm, balanced Other electrical characteristics Complies with ITU-T Rec. G.703 Framing ITU-T G.704-1988 with CRC4 Line coding HDB3 Clock and data recovery Complies with ITU-T Rec. G.823-1988 Jitter tolerance Complies with ITU-T Rec. G.823, G.737, G.739, G.742-1988 Connectors BNC for 75 Ohm lines RJ-48C for 120 Ohm lines Telephony bus connector H.100 (PCI) and H.110 (CompactPCI) style connectors Loopback Supports switch-selectable local analog loopback and software selectable local digital loopback 3 ® Datasheet Dialogic DM3 Media Boards Technical Specifications (cont.) Approvals and Compliance Hazardous substances RoHS Compliance Information at http://www.dialogic.com/rohs Safety and EMC Canada ICES-003 Class A ULc 60950 File E96804 Europe EN60950 EN55022 DEN55024 Japan VCCI Class A United States FCC Part 15 Class A UL 60950 File E96804 International IEC60950 CISPR 22 CISPR 24 Telecom Approvals United States EBZUSA-31207-XD-T Canada IC:885-7969A European Union DoC 01/10/2003 Country-speciŢc approvals See the Product Declarations & Global Approvals list at http://www.dialogic.com/declarations/ or contact your Authorized Distributor Reliability/Warranty Estimated MTBF Per Telecordia Method I Case I PCI: 87,000 CompactPCI: 106,000 Warranty Warranty information at http://www.dialogic.com/warranties Audio Signal Usable receive range –40 dBm0 to 0 dBm0 nominal, conŢgurable by parameter** Automatic gain control Application can enable/disable output level, conŢgurable by parameter** Silence detection –40 dBm nominal, software adjustable** Transmit level (weighted average) –12.5 dBm nominal, conŢgurable by parameter** Transmit volume control 40 dB adjustment range, with application-deŢnable increments and legal limit cap Frequency Response 24 kb/s 300 Hz to 2600 Hz ±3 dB 32 kb/s 300 Hz to 3400 Hz ±3 dB 64 kb/s 300 Hz to 3400 Hz ±3 dB Audio Digitizing 24 kb/s OKI ADPCM @ 6 kHz sampling 32 kb/s OKI ADPCM @ 8 kHz sampling 48 kb/s G.711 PCM (µ-law for T-1 and A-law for E-1) @ 6 kHz sampling rate 64 kb/s G.711 PCM (µ-law for T-1 and A-law for E-1) @ 8 kHz sampling rate 64 kb/s Linear 8 kHz 8-bit WAV 128 kb/s Linear 8 kHz 16-bit WAV 88 kb/s Linear 11 kHz 8-bit WAV 176 kb/s Linear 11 kHz 16-bit WAV Digitization selection Selectable by application on function call-by-call basis Playback speed control Pitch controlled Available on the following 8 kHz coders: OKI ADPCM, G.711 PCM, Linear Adjustment range: ±50% Adjustable through application or programmable DTMF control 4 ® Dialogic DM3 Media Boards Datasheet Technical Specifications (cont.) DTMF Tone Detection DTMF digits 0 to 9, *, #, A, B, C, D per Telcordia LSSGR Sec. 6 Dynamic range (T-1) –36 dBm to +3 dBm per tone, conŢgurable by parameter** (E-1) –39 dBm to 0 dBm per tone, conŢgurable by parameter** Minimum tone duration 32 ms; can be increased with software conŢguration Interdigit timing Detects like digits with a >45 ms interdigit delay Detects different digits with a 0 ms interdigit delay Acceptable twist and frequency variation (T-1) Meets Telcordia LSSGR Sec 6 and EIA 464 requirements (E-1) Meets ITU-T Q.23 recommendations** Noise tolerance Meets Telcordia LSSGR Sec 6 and EIA 464 requirements for Gaussian, impulse, and power line noise tolerance Cut-through (T-1) Local echo cancellation permits 100% detection with a >4.5 dB return loss line (E-1) Digital trunks use separate transmit and receive paths to network Performance dependent on far-end handset’s match to local analog loop Talk-off Detects less than 10 digits while monitoring Telcordia TR-TSY-000763 standard speech tapes (LSSGR requirements specify detecting no more than 470 total digits) Detects 0 digits while monitoring MITEL speech tape #CM 7291 Global Tone Detection Tone type Programmable for single or dual Maximum number of tones Application-dependent Frequency range Programmable within 300 Hz to 3500 Hz Maximum frequency deviation Programmable in 5 Hz increments Frequency resolution ±5 Hz. Separation of dual frequency tones is limited to 62.5 Hz at a signal-to-noise ratio of 20 dB Timing Programmable cadence qualiŢer, in 10 ms increments Dynamic range (T-1) Default set at –36 dBm to +3 dBm per tone, programmable (E-1) Default set at –39 dBm to +0 dBm per tone, programmable Global Tone Generation Tone type Generate single or dual tones Frequency range Programmable within 200 Hz to 4000 Hz Frequency resolution 1 Hz Duration 10 ms increments Amplitude (T-1) –43 dBm0 to –3 dBm0 per tone nominal, programmable (E-1) –40 dBm0 to +0 dBm0 per tone nominal, programmable MF Signaling (T-1) R1 MF digits 0 to 9, KP, ST, ST1, ST2, ST3 per Telcordia LSSGR Sec 6, TR-NWT-000506 and ITU-T Q.321 Transmit level Complies with Telcordia LSSGR Sec 6, TR-NWT-000506 Signaling mechanism Complies with Telcordia LSSGR Sec 6, TR-NWT-000506 Dynamic range for detection –25 dBm to +3 dBm per tone Acceptable twist 6 dB Acceptable freq. variation Less than ±1 Hz MF Signaling (E-1) R2 MF digits All 15 forward and backward signal tones per ITU-T Q.441 Transmit level –8 dBm0 per tone, nominal, per ITU-T Q.454; programmable Signaling mechanism Supports the R2 compelled signaling cycle and non-compelled pulse requirements per ITU- T Q.457 and Q.442 Dynamic range for detection –35 dBm to –5 dBm per tone Acceptable twist 7 dB Acceptable freq. variation Less than ±1 Hz 5 ® Datasheet Dialogic DM3 Media Boards Technical Specifications (cont.) Call Progress Analysis Busy tone detection Default setting designed to detect 74 out of 76 unique busy/congestion tones used in 97 countries as speciŢed by ITU-T Rec. E., Suppl. #2 Default uses both frequency and cadence detection Application can select frequency only for faster detection in speciŢc environments Ring back detection Default setting designed to detect 83 out of 87 unique ring back tones used in 96 countries as speciŢed by ITU-T Rec. E., Suppl. #2 Uses both frequency and cadence detection Positive voice detection accuracy >98% based on tests on a database of real-world calls in North America Positive voice detection speed Detects voice in as little as 1/10th of a second Positive answering machine detection Standard Fax/modem detection Preprogrammed Intercept detection Detects entire sequence of the North American tri-tone Other intercept tone sequences can be programmed Dial tone detection before dialing Application enable/disable Supports up to three different user-deŢnable dial tones Programmable dial tone drop out debouncing (when not part of regulatory approval) Tone Dialing DTMF digits 0 to 9, *, #, A, B, C, D per Telcordia LSSGR Sec 6, TR-NWT-000506, ITU-T Q.23 Frequency variation Less than ±1 Hz Rate 10 digits/s, conŢgurable by parameter** Level (T-1) –4.0 dBm per tone, nominal, conŢgurable by parameter** (E-1) –7.5 dBm per tone, nominal, country-speciŢc** Protocols T-1 CAS E&M (wink start, immediate start), loop start, ground start; feature group A, B, and D T-1 ISDN NI-2, 4ESS, 5ESS, DMS100, DMS250, INS1500, Q.Sig E-1 CAS Many country-speciŢc MFC-R2 variants ® For more details, refer to the latest Dialogic Global Call Protocol Package release notes E-1 ISDN NET5, DPNSS, DASS2,Q.Sig Additional Components • Multidrop CT Bus cables (CBLCTB68C3DROP, CBLCTB68C4DROP, CBLCTB68C8DROP, CBLCTB68C12DROP, CBLCTB68C16DROP) • CT Bus/SCbus adapter (CTBUSTOSCBUSADP) • SCbus terminator kits (1SCBUS1TERMKIT, 2SCBUS1TERMKIT, 3SCBUS1TERMKIT) • Rear I/O module for CompactPCI boards — Unkeyed (works in all chassis): CPCIREARRJ48, CPCIREARE1120, REARIOV19E175 — Keyed (works only in PICMG 3.x chassis): CPCIREARRJ48KYD, CPCIREARE1120KY, REARIOV19E175KY • 120 Ohm to 75 Ohm converter (supplied by a third party) Ordering Information Product Code Order Code Description DMV9604T1PCIW 882-692 96-port Digital T1, voice, PCI DMV12004E1PCIW 882-691 12-port Digital E1, voice, PCI DMV12004E1PCIWCN 882-742 12-port Digital E1, voice, PCI, for China 6 To learn more, visit our site on the World Wide Web at http://www.dialogic.com Dialogic Corporation 9800 Cavendish Blvd., 5th ţoor Montreal, Quebec CANADA H4M 2V9 INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH PRODUCTS OF DIALOGIC CORPORATION (“DIALOGIC”). NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED AGREEMENT BETWEEN YOU AND DIALOGIC, DIALOGIC ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC DISCLAIMS ANY EXPRESS OR IMPLIED ® WARRANTY, RELATING TO SALE AND/OR USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT OF A THIRD PARTY. Dialogic products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility applications. Dialogic may make changes to speciŢcations, product descriptions, and plans at any time, without notice. Dialogic is a registered trademark of Dialogic Corporation. Dialogic’s trademarks may be used publicly only with permission from Dialogic. Such permission may only be granted by Dialogic’s legal department located at the address given above. Any authorized use of Dialogic’s trademarks will be subject to full respect of the trademark guidelines published by Dialogic from time to time and any use of Dialogic’s trademarks requires proper acknowledgement. Windows is a registered trademark of the Microsoft Corporation in the United States and/or other countries. Other names of actual companies and products mentioned herein are the trademarks of their respective owners. Dialogic encourages all users of its products to procure all necessary intellectual property licenses required to implement their concepts or applications, which licenses may vary from country to country. None of the information provided in this datasheet other than what is listed under the section entitled Technical SpeciŢcations forms part of the speciŢcations of the product and any beneŢts speciŢed are not guaranteed. Positive Answering Machine Detection/Positive Voice Detection These performance results were measured using speciŢc computer systems and/or components within speciŢc lab environments and under speciŢc system conŢgurations. Any difference in system hardware, software design, or conŢguration may affect actual performance. The results are furnished for informational use only and should not be construed as a commitment by Dialogic. Dialogic assumes no responsibility or liability for any errors or inaccuracies. Outbound Dialing/Telemarketing ® Outbound dialing systems may be subject to certain laws or regulations. Dialogic makes no representation that Dialogic products will satisfy the requirements of any such laws or regulations (including, without limitation, any regulations dealing with telemarketing). **ConŢgurable to meet country-speciŢc PTT requirements. Actual speciŢcation may vary from country to country for approved products. Copyright © 2007 Dialogic Corporation All rights reserved. 10/07 3967-06 www.dialogic.com