Industrial Trading

Description

XP Power SMQ400PS18-C 400W AC/DC U-Channel Power Supply

Part Number

SMQ400PS18-C

Price

Request Quote

Manufacturer

XP POWER

Lead Time

Request Quote

Category

Power Supply Board

Specifications

Cooling

Via internal fan

Efficiency

80% typical

Hold Up Time

20 ms minimum at 120 VAC & 80% load

Input Current

5.00 A at 90 VAC (SMQ300), 6.35 A at 90 VAC (SMQ400)

Input Frequency

47-63 Hz

Input Voltage

90-264 VAC (120-370 VDC)

Inrush Current

35 A max at 230 VAC

Isolation

3000 VAC Input to Output, 1500 VAC Input to Ground, 250 VDC Output to Ground

Line Regulation

±1%

Load Regulation

±1%

Minimum Load

No minimum load required

MTBF

138 kHrs per MIL-HDBK-217F

Operating Humidity

5-90% RH, non-condensing

Operating Temperature

0 °C to +70 °C, derate linearly from 100% at +50 °C to 50% at +70 °C

Output Voltage

12 to 54 VDC

Overcurrent protection

120-150% of nominal current, auto recovery

Overtemperature Protection

Unit shuts down, auto recovery

Overvoltage Protection

115-130% Vnom, recycle input to reset

Power Density

4.7 W/In3 (SMQ300), 6.25 W/In3 (SMQ400)

Power Factor

0.99 typical

Remote On/Off

On - TTL Logic High or Open circuit; Off - TTL Logic Low or Short circuit

Remote sense

Compensates for up to 0.5 V drop

Ripple & Noise

1% pk-pk, 20 MHz BW

Shock

15 g (non-operation), 11 ms half; sine-wave, 3 times for each axis

Signals

DC OK, TTL HIGH within 100-500 ms; LOW 1 ms before loss of regulation

Start Up Delay

2.5 s typical at 120 VAC

Storage Temperature

-20 °C to +85 °C

Switching Frequency

60 kHz typical for PFC stage, 30 kHz typical for main converter

Transient Response

5% max. deviation, recovery to within 1% in 500 µs for a 50% load change

Vibration

10 Hz - 55 Hz (non-operation) 2 g, sweep time 3 mins, 60 mins/axis

Features

DC OK
High Peak Load Rating
High Power Density
Internal Fan
Remote On/Off
Single Outputs from 12.0 V to 54.0 V
Universal Input

Datasheet

XP Power-SMQ400PS18-C-datasheet1-1946375804.pdf

211 KiB

Download

Extracted Text

300/400 Watts xppower.com SMQ Series • High Power Density • High Peak Load Rating • DC OK • Remote On/Off • Universal Input • Single Outputs from 12.0 V to 54.0 V • Internal Fan Specification Input General Input Voltage • 90-264 VAC (120-370 VDC) Efficiency • 80% typical Input Frequency • 47-63 Hz Isolation • 3000 VAC Input to Output, 1500 VAC Input to Ground, Input Current • 5.00 A at 90 VAC (SMQ300), 250 VDC Output to Ground 6.35 A at 90 VAC (SMQ400) Switching Frequency • 60 kHz typical for PFC stage, Inrush Current • 35 A max at 230 VAC 30 kHz typical for main converter Power Factor • 0.99 typical 3 3 Power Density • 4.7 W/In (SMQ300), 6.25 W/In (SMQ400) Earth Leakage Current • <2.5 mA at 230 VAC/50Hz Signals • DC OK, TTL HIGH within 100-500 ms <1.5 mA at 115 VAC/60Hz LOW 1 ms before loss of regulation MTBF • 138 kHrs per MIL-HDBK-217F Output Output Voltage • 12 to 54 VDC - see table Environmental Output Voltage Trim • See table Operating Temperature • 0 ˚C to +70 ˚C, derate linearly from Minimum Load • No minimum load required 100% at +50 ˚C to 50% at +70 ˚C Start Up Delay • 2.5 s typical at 120 VAC Cooling • Via internal fan Hold Up Time • 20 ms minimum at 120 VAC & 80% load Operating Humidity • 5-90% RH, non-condensing Line Regulation •±1% Storage Temperature • -20 ˚C to +85 ˚C Load Regulation •±1% Shock • 15 g (non-operation), 11 ms half Transient Response • 5% max. deviation, recovery to within sine-wave, 3 times for each axis 1% in 500 µs for a 50% load change Vibration • 10 Hz - 55 Hz (non-operation) 2 g, Ripple & Noise • 1% pk-pk, 20 MHz BW sweep time 3 mins, 60 mins/axis Overvoltage Protection • 115-130% Vnom, recycle input to reset Overcurrent Protection • 120-150% of nominal current, EMC & Safety auto recovery Emissions • EN55022 and FCC Part 15, Overtemperature • Unit shuts down, auto recovery level B conducted Protection Harmonic Currents • EN61000-3-2 Remote Sense • Compensates for up to 0.5 V drop Voltage Flicker • EN61000-3-3 Remote On/Off • On = TTL Logic High or Open circuit ESD Immunity • EN61000-4-2, level 2 contact, level 3 air, Off = TTL Logic Low or Short circuit Perf Criteria A Radiated Immunity • EN61000-4-3, 3 V/m, Perf Criteria A EFT/Burst • EN61000-4-4, level 2, Perf Criteria A Surge • EN61000-4-5, level 3, Perf Criteria A Conducted Immunity • EN61000-4-6, level 2, Perf Criteria A Dips & Interruptions • EN61000-4-11, 30% 10 ms, 60% 100 ms, 100% 5000 ms Perf Criteria A, B, B Safety Approvals • UL60950, CSA C22.2 No.60950, EN60950, CE Mark LVD AC-DC AC-DC L N SMQ Models and Ratings (1) Maximum Output Voltage Output Current Model (2) (3) Power Number Preset Range Maximum Peak 12 V 12-15 V 25.00 A 46.66 A SMQ300PS12-C†^ 15 V 12-15 V 20.00 A 46.66 A SMQ300PS15-C†^ 18 V 16-21 V 16.66 A 33.33 A SMQ300PS18-C 24 V 22-30 V 12.50 A 23.33 A SMQ300PS24-C†^ 300 W 27 V 22-30 V 11.11 A 23.33 A SMQ300PS27-C 36 V 31-47 V 8.33 A 17.07 A SMQ300PS36-C 48 V 48-56 V 6.25 A 12.72 A SMQ300PS48-C†^ 54 V 48-56 V 5.55 A 12.72 A SMQ300PS54-C 12 V 12-15 V 33.33 A 46.66 A SMQ400PS12-C†^ 15 V 12-15 V 26.66 A 46.66 A SMQ400PS15-C†^ 18 V 16-21 V 22.22 A 33.33 A SMQ400PS18-C 24 V 22-30 V 16.66 A 23.33 A SMQ400PS24-C†^ 400 W 27 V 22-30 V 14.81 A 23.33 A SMQ400PS27-C 36 V 31-47 V 11.11 A 17.07 A SMQ400PS36-C 48 V 48-56 V 8.33 A 12.72 A SMQ400PS48-C†^ 54 V 48-56 V 7.40 A 12.72 A SMQ400PS54-C Notes 1. Other voltages are available. Contact sales office for details. 2. Standard models have foldback mode current protection with a high peak load capacity. This peak can be taken for 500 µs max. 3. For optional U-channel versions without fan/cover, change SMQ prefix to SMU, and delete suffix ‘-C’ from model number. Requires forced air cooling at 18 CFM. † Available from Farnell. See pages 204-206. ^ Available from Newark. See pages 207-208. Mechanical Details A Mounting Hole 8 Places Scale 4:1 1.10 (27.94)* 1.50 (38.1) B B 2.00 (50.8) 0.22 (5.6) A A 0.25 (6.4) 0.75 (19.05) UNC6-32 (Zn-plated) 2.00 (50.8) 6.00 (152.4) 2.00 (50.8) 0.75 (19.05) 1.10 (27.94) A A 4.00 (101.6) Pin Control 1 B B 1.80 (45.72) 2.50 (63.5) B B A A 1.10 (27.94) 0.75 (19.05) Terminal Block 8.00 (203.2) M3 Screw 3 Pins 8.25 mm center Terminal Block B Mounting Hole 8 Places M3.5 Screw 6 Pins 9.5 mm center Scale 4:1 1.25 (31.75) Control Pin Function 0.22 (5.6) 1 DC OK A A 2 On/Off 0.25 (6.4) B B 1.50 (38.1) 3 RTN 2.00 (50.8) 4 -sense 1.10 (27.94)* M4 5 +sense (Zn (yellow) - plated) Notes 1. Dimensions in inches (mm). 2. Control connector mates with JST XHP-5 or equivalent. 3. Fan connector is wired in parallel to the internal fan. No auxiliary output is available. 4. Weight: 2.42 lbs (1100 g) approx. 5. Maximum mounting screw penetration: 0.15 (4.00) from case outer surfaces. 6. Remote ON/OFF activation is 3 minutes max. * Dimension for SMU models is 1.20 (30.48). 17-Apr-07 8.25 (0.32) VO+ VO- 0.02 (0.6) 0.02 (0.6) 0.07 (1.9) 0.07 (1.9)

Frequently asked questions

Industrial Trading' parent company, GID Industrial, specializes in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

The warranty we offer will be based on what we negotiate with our suppliers. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

We use FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Industrial Trading will definitely serve you. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

Visa, MasterCard, Discover, and American Express are all accepted by Industrial Trading. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

What they say about us

FANTASTIC RESOURCE

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Why buy from GID?

What they say about us

Related Products