TDK-LAMBDA CA1000 H17096
Specifications
AC Input Volt. range & Freq.
85-264VAC, 47-63Hz
Altitude
3,000m operating
Conducted EMI
EN55022 level A
Cooling
Internal fan provides forced-air cooling. Airfl ow intake on I/P end, exhaust on O/P end of unit.
DC Input Voltage Range
120 - 360VDC (800W maximum output to 45C)
Efficiency
75% typical (confi guration and input dependent)
Hold Up Time
>15ms
Humidity
RH 5% - 95% Non-condensing
Input Current
16A maximum
Inrush Current
Less than 50A
Isolation
Input - Output 4.3kVDC, Input - Ground 2.3kVDC, Output - Ground 500VDC
Leakage Current
1.1mA @ 264VAC, 63Hz (see input fi lter options in detailed product datasheet)
No Load Operation
No preload is required on any output module.
Operating Temperature
-20°C to +50°C full load, derate each output at 2.5% /°C from 50°C to 65°C.
Options (see option codes)
AC Fail, Global Inhibit, Module Inhibit, 5V@50mA aux., Parallel, Low Leakage.
Output Line Regulation
0.5% maximum.
Output Load Regulation
0.2% maximum.
Output Power
800W@85VAC (50°C max); 1000W@100VAC (50°C max); 1000W@90VAC (45°C max);
Power Factor Correction
Compliant to EN61000-3-2 ( > 0.99 typical, reduced PFC > 255VAC)
Remote Sense
Available on single output modules only, refer to the module table.
Ripple & Noise
2% pk-pk or 100mV (Whichever is greater)
Safety Agency Certification
UL, EN/IEC60950-1, UL, EN/IEC60601-1*, IEC, EN61010-1, CE Mark
Shock
3,000 bumps, 10G, 16ms half-sine pulses.
Size (WxHxD) in.
7” x 2.5” x 11”
Storage Temperature
-40°C to +85°C
Switching Frequency
100kHz on PFC, 200kHz on forward converter.
Temperature Coefficient
0.02% per °C
Thermal Protection
Converter protected against over-temperature conditions. Recycle I/P power to restore output.
Vibration
1.5G, 10 - 200Hz
Warranty
Three Years
Datasheet
Extracted Text
Alpha 1000 Series 1000W Multiple Output Modular Power Supply Features u Universal AC Input u Power factor Corrected u Capable of up to 14 fully regulated and indepedent outputs u Output Voltages from 1.8V - 48V u Low Leakage Options u International Safety Agency Certifi cation u Fast-on Tab Connections u No Minimum Load u Wide Range Output Modules Key Market Segments & Applications Specifi cations Model AC Input Volt. range & Freq. - 85-264VAC, 47-63Hz DC Input Voltage Range - 120 - 360VDC (800W maximum output to 45C) Input Current A 16A maximum Inrush Current A Less than 50A Leakage Current - 1.1mA @ 264VAC, 63Hz (see input fi lter options in detailed product datasheet) Effi ciency % 75% typical (confi guration and input dependent) Power Factor Correction - Compliant to EN61000-3-2 ( > 0.99 typical, reduced PFC > 255VAC) Conducted EMI - EN55022 level A Output Power W 800W@85VAC (50°C max); 1000W@100VAC (50°C max); 1000W@90VAC (45°C max); 1000W for 30 seconds maximum @ 85VAC followed by 800W for 60 seconds minimum. Output Load Regulation - 0.2% maximum. Output Line Regulation - 0.5% maximum. Ripple & Noise - 2% pk-pk or 100mV (Whichever is greater) No Load Operation - No preload is required on any output module. Hold Up Time ms >15ms Remote Sense - Available on single output modules only, refer to the module table. Options (see option codes) - AC Fail, Global Inhibit, Module Inhibit, 5V@50mA aux., Parallel, Low Leakage. Operating Temperature °C -20°C to +50°C full load, derate each output at 2.5% /°C from 50°C to 65°C. Thermal Protection - Converter protected against over-temperature conditions. Recycle I/P power to restore output. Storage Temperature °C -40°C to +85°C Temperature Coeffi cient - 0.02% per °C Humidity % RH 5% - 95% Non-condensing Altitude - 3,000m operating Cooling - Internal fan provides forced-air cooling. Airfl ow intake on I/P end, exhaust on O/P end of unit. Isolation - Input - Output 4.3kVDC, Input - Ground 2.3kVDC, Output - Ground 500VDC Switching Frequency - 100kHz on PFC, 200kHz on forward converter. Vibration - 1.5G, 10 - 200Hz Shock - 3,000 bumps, 10G, 16ms half-sine pulses. Safety Agency Certifi cation - UL, EN/IEC60950-1, UL, EN/IEC60601-1*, IEC, EN61010-1, CE Mark Size (WxHxD) in. 7” x 2.5” x 11” Warranty - Three Years Notes: Consult datasheet for additional specifi cations * Low leakage fi lter options only. 1-800-526-2324 • www.us.tdk-lambda.com/lp/ 9 ALPHA 1000 Series 1 Case Codes 3 Option Codes If required the following options may be added to the confi guration Choose the converter which best fi ts your total power needs: by placing the code after the module. Code Wattage Max Slots Size (H x W x L) Input Voltage (i.e. Inhibiting a 5V @ 25A = 5B + Inhibit code = “5BIN”) CA1000 1000* 7 2.5” x 7” x 11” 85 - 265VAC Code Description Available On * Note: CA1000 derates to 800W for 85–100VAC input with a peak of 1000W for 30 seconds max. 2 MF Mains Fail All modules except This option provides an AC fail signal, Dual output (E, H, P) 2 Output Module Codes power supply inhibit, and 5V@50mA auxiliary supply. This is only placed in (1) Code V1 Adjust V1 Amps V2 Adjust V2 Amps Slot(s) the fi rst module slot. (TTL compatible reference to 0 volts of Aux. Supply) L 1.8 - 3.2 25 - - 1 T 1.8 - 3.2 60 - - 2 PP Parallel for Power Modules: A, B, C, D, Q 2.7 - 3.9 25 - - 1 This option allows 2 adjacent modules F, G, M, N, Q, R R 2.7 - 3.9 60 - - 2 to be paralleled together for increased B 4.5 - 5.5 25 - - 1 output power. Bus bars provided. A 4.5 - 5.5 60 - - 2 BB 4.5 - 6.5 25 - - 1 PA Parallel for Redundancy Modules: A, B, C, D, AA 4.5 - 6.5 60 - - 2 This option allows modules to be F, G, M, N, Q, R, S S 2.5 - 5.7 85 - - 2 connected for N+1 redundancy. A DC M 5.0 - 16.0 8 - - 1 good signal is also offered (electrically C 5.0 - 16.0 16(3) - - 1 F 9.0 - 16.0 33 - - 2 similar to AC fail.) No bus bars provided. U 10.0 - 21.0 16 - - 1 IN3 Inhibit Modules A, B, C, D, N 18.0 - 29.0 5 - - 1 Module inhibit and DC good signal. F, G, J, M, N, Q, R D 18.0 - 29.0 8 - - 1 (TTL compatible referenced to (-V) K 18.0 - 29.0 15 - - 2 G 17.5 - 29.0 25(3) - - 2 of the module) J 30.0 - 48.0 10(3) - - 2 Low Leakage Options (Max values stated) E 5.0 - 16.0 8(3) 5.0 - 16.0 8(3) 1 (4) 120VAC, 60Hz 240VAC, 60Hz 264VAC, 63Hz Conducted EMI P 18.0 - 29.0 5 5.0 - 16.0 8(3) 1 LL 88 µA 197 µA 233 µA Curve A H 18.0 - 32.0 5(3) 18.0 - 32.0 5(3) 1 RL 50 µA 112 µA 132 µA >Curve A Notes: 1) The total # of slots must not exceed 7 for CA1000. TL 24 µA 53 µA 63 µA >Curve A 2) Slot position may change upon order placement. 3) Module Deratings: C derates linearly to 12A from 12.1V–15V Notes: 1) Only one option per module may be used. E & P 8A rating derates to 6A in slots 4 & 5 2) Mains Fail: AC Fail “AC On” = ≤ 0.8V, 50mA max. H derates from 5A to 4A in slots 4 & 5 “AC Off” = open circuit, 50V abs max. G derates to 21A above 24.5V PS Inhibit “PS On” = ≥ 2.0V or open circuit. J derates 0.25A/V above 40V “PS Off” = ≤ 0.8V @ 5mA. (TTL compatible, Referenced to 0 volts of Aux. Supply.) 3) Inhibit: DC Good Electrically similar to AC fail module. Sample Confi gurations Inhibit Electrically similar to PS inhibit. 4) Type testing result Output 1 Output 2 Output 3 Output 4 Output 5 V A V A V A V A V A Outline Drawing CA1000-24G 24 16.5 - - - - - - - - CA1000-5APP-5APP * 5 120 - - - - - - - - 279.00 CA1000-5A-12.7C 5 60 12.7 16 - - - - - - 4.50 248.00 CA1000-24G-5/12E 24 25 5 8 12 8 - - - - 37.00 CA1000-5A-24G-12C-12C 5 60 24 25 12 16 12 16 - - 25.00 CA1000-5BMF-24D-6/12E 5 25 24 8 6 8 12 8 - - 4.5MM MAXIMUM SCREW PENETRATION CA1000-5B-5CIN-12C-12/12E 5 25 5 16 12 16 12 8 12 8 8 OFF M4 PRIMARY FIXINGS CA1000-5S-12F-12C-5/24P 5 85 12 33 12 16 5 8 24 5 Notes: Total output power must not exceed 1000W converter limits. MAINS INPUT * Modules in parallel. 216.00 6.00 Other Modular Products NV 350W to 700W up to 8 outputs Vega 450W to 900W up to 10 outputs Alpha1500 1500W up to 16 outputs 63.00 For Additional Information, please visit 2 OFF M4 SECONDARY FIXINGS us.tdk-lambda.com/lp/products/alpha-series.htm 4.5MM MAXIMUM SCREW PENETRATION THESE 2 FIXINGS MUST ONLY TO BE USED IN CONJUNCTION WITH THE PRIMARY FIXINGS 15.00 110.00 GENERAL TOLERANCE Å} 0.5MM 1-800-526-2324 • www.us.tdk-lambda.com/lp/ 10 Revision A7: Nov 2011 175.50 50.00 115.50 30.00 12.00 34.00 7 OUTPUT MODULE SLOTS
Frequently asked questions
How does Industrial Trading differ from its competitors?

Is there a warranty for the CA1000 H17096?

Which carrier will Industrial Trading use to ship my parts?

Can I buy parts from Industrial Trading if I am outside the USA?

Which payment methods does Industrial Trading accept?

Why buy from GID?

Quality
We are industry veterans who take pride in our work

Protection
Avoid the dangers of risky trading in the gray market

Access
Our network of suppliers is ready and at your disposal

Savings
Maintain legacy systems to prevent costly downtime

Speed
Time is of the essence, and we are respectful of yours
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods