Alpha 1000 1000W Multiple Output Modular Power Supply ‹ Customized Power Supplies ‹ Universal AC Input ‹ Power factor Corrected ‹ Capable of up to 14 fully regulated and independent outputs ‹ Output Voltages from 1.8V - 48V ‹ Low Leakage Options ‹ Input Transient Protection ‹ Compact Package ‹ International Safety Agency Approvals Alpha Features and Benefits Feature Benefit ‹ PFC compliant to EN61000-3-2 ‹ Supports global use ‹ Fast-on Tab Connections ‹ Quick installation ‹ No Minimum Load ‹ Eliminates the need for external components ‹ Wide Range Output Modules ‹ Capable of providing non-standard voltages, eliminates customs Specifications MODELS ITEMS AC Input Volt. range & Freq. - 85-264VAC, 47-63Hz DC Input Voltage Range - 120 - 360VDC (800W maximum output to 45C) Input Current A 16A maximum Inrush Current A Less than 50A Leakage Current - 1.1mA @ 260VAC, 50Hz (see input filter options in detailed product datasheet) Efficiency % 75% typical (configuration and input dependent) Power Factor Correction - Compliant to EN61000-3-2 ( > 0.95 typical, reduced PFC > 255VAC) Conducted EMI - EN55022 level A Output Power W 800W@85VAC (50°C max); 1000W@100VAC (50°C max); 1000W@90VAC (45°C max); 1000W for 30 seconds maximum @ 85VAC followed by 800W for 60 seconds minimum. Output Load Regulation - 0.2% maximum. Output Line Regulation - 0.5% maximum. Ripple & Noise - 2% pk-pk No Load Operation - No preload is required on any output module. Hold Up Time ms Output voltages will remain within specified regulation for a minimum of 15mS after loss of applied power on the AC input at full rated output Remote Sense - Available on single output modules only, refer to the module table. Options (see option codes) - AC Fail, Global Inhibit, Module Inhibit, 5V@50mA aux., Parallel, Low Leakage. Operating Temperature °C -20°C to +50°C full load, derate each output at 3.3% /°C from 50°C to 65°C. Thermal Protection - Converter protected against over-temperature conditions. Recycle I/P power to restore output. Storage Temperature °C -40°C to +85°C Temperature Coefficient - 0.02% per °C Humidity % RH 5% - 95% Non-condensing Altitude - 0 - 10,000 feet Operating (3,300 metres) Cooling - Internal fan provides forced-air cooling. Airflow intake on I/P end, exhaust on O/P end of unit. Isolation - Input - Output 3000VAC, Input - Ground 1500VAC, Output - Ground 500VDC Switching Frequency - 100kHz on PFC, 200kHz on forward converter. Vibration - 1.5G, 10 - 200Hz Shock - 3,000 bumps, 10G, 16ms half-sine pulses. Safety Agency Approvals - UL60950-1, EN/IEC60950-1, UL60601-1, EN/IEC60601-1, IEC61010-1, EN61010-1, CE Mark Module Slots - 7 Size (WxHxD) in. 7" x 2.5" x 11" Warranty - Three Years Notes: (Consult datasheet for additional specifications) 3055 Del Sol Blvd • San Diego, CA 92154 • 1-800-LAMBDA-4 Alpha 1000 1 Case Codes 3 Option Codes If required the following options may be added to the configuration by placing the Choose the converter which best fits your total power needs: code after the module. (i.e. Inhibiting a 5V @ 25A = 5B + Inhibit code = “5BIN”) C Co od de e W Wa atttta ag ge e M Ma ax x S Sllo otts s S Siiz ze e ((H H x x W W x x L L)) IIn np pu utt V Vo olltta ag ge e Code Description Available On CA1000 1000* 7 2.5" x 7" x 11" 85 - 265VAC 2 MF Mains Fail All modules except * Note: CA1000 derates to 800W for 85–100VAC input with a peak of 1000W for This option provides an AC fail signal, power supply Dual output (E, H, P) 30 seconds maximum. inhibit, and 5V@50mA auxiliary supply. This is only (TTL compatible reference placed in the first module slot. to 0 volts of Aux. Supply) 2 Output Module Codes PP Parallel for Power Modules: A, B, C, D, From the table below match the available modules to your voltage This option allows 2 adjacent modules to be paralleled F, G, M, N, Q, R together for increased output power. Bus bars provided. and current requirements. PA Parallel for Redundancy Modules: A, B, C, D, Format = Desired Voltage + Module Code Letter This option allows modules to be connected for N+1 F, G, M, N, Q, R, S (5V@20A=“5B” or (5.1V@5A) & 12.7@2A=“5.1/12.7E”) A DC good signal is also offered (electrically redundancy. similar to AC fail.) No bus bars provided. 3 1 Code V1 nom Amps V2 nom Amps V1 adjust V2 adjust Slot(s) 3 IN Inhibit Modules A, B, C, D, L 2.0 25 - - 1.8 - 2.7 - 1 Module inhibit and DC good signal. F, G, J, M, N, Q, R T 2.0 60 - - 1.8 - 2.7 - 2 (TTL compatible referenced to (-V) of the module) Q 3.3 25 - - 2.7 - 3.9 - 1 Low Leakage Options All converters R 3.3 60 - - 2.7 - 3.9 - 2 Max. Leakage Current Conducted RFI B 5 25 - - 4.5 - 5.5 - 1 LL 212 µA Curve A A 5 60 - - 4.5 - 5.5 - 2 RL 100 µA Above Curve A S 5 85 - - 2.5 - 5.7 - 2 TL 50 µA Above Curve A M 12 8 - - 5.0 - 15.0 - 1 3 C 12 16 - - 5.0 - 15.0 - 1 Notes: 1) Only one option per module may be used. F 12 33 - - 10.0- 15.0 - 2 2) Mains Fail: AC Fail “AC On” = ≤ 0.8V, 50mA max. N 24 5 - - 18.0 - 28.0 - 1 “AC Off” = open circuit, 50V abs max. D 24 8 - - 18.0 - 28.0 - 1 PS Inhibit “PS On” = ≥ 2.0V or open circuit. G 24 25 - - 18.0 - 28.0 - 2 “PS Off” = ≤ 0.8V @ 5mA. J 36 10 - - 36.0 - 48.0 - 2 (TTL compatible, Referenced to 0 volts of Aux. Supply.) J 48 7.5 - - 36.0 - 48.0 - 2 3) Inhibit: DC Good Electrically similar to AC fail module. 3 3 E 12 8 12 8 5.0 - 15.0 5.0 - 15.0 1 Inhibit Electrically similar to PS inhibit. 3 P 24 5 12 8 18.0 - 28.0 5.0 - 15.0 1 3 3 H 24 5 24 5 18.0 - 28.0 18.0 - 28.0 1 Outline Drawing Notes: 1) The total # of slots must not exceed 7 for CA1000. 2) The written order determines the slot position. (This may change upon 279.00 4.50 248.00 order placement.) 37.00 3) Module Deratings: C derates linearly to 12A from 12.1V–15V 25.00 E & P: 8A rating derates to 6A in slots 4 & 5. H derates from 5A to 4A in slots 4 & 5. 4.5MM MAXIMUM SCREW PENETRATION 8 OFF M4 PRIMARY FIXINGS 4) Remote Sensing: Dual output modules do not have remote sensing. Modules (A, B, Q, R, S) have 0.5V total line drop, 1V for all others. 5) Format for module code = desired voltage + module code letter. MAINS INPUT Refer to the following examples: (26V @ 24A = “26G”) or ( 5.1V @ 8A & 12V @ 8A = “5.1/12E”). 216.00 6.00 Sample Configurations Output 1 Output 2 Output 3 Output 4 Output 5 VA V A V A V A V A CA1000-24G 24 16.5 - - - - - - - - CA1000-5APP-5APP* 5 120 - - - - - - - - CA1000-5A-12.7C 5 60 12.7 16 - - - - - - CA1000-24G-5/12E 24 25 5 8 12 8 - - - - CA1000-5A-24G-12C-12C 5 60 24 25 12 16 12 16 - - CA1000-5BMF-24D-6/12E 5 25 24 8 6 8 12 8 - - CA1000-5B-5CIN-12C-12/12E 5 25 5 16 12 16 12 8 12 8 63.00 CA1000-5S-12F-12C-5/24P 5 85 12 33 12 16 5 8 24 5 2 OFF M4 SECONDARY FIXINGS Note: Total output power must not exceed 1000W converter limits. 4.5MM MAXIMUM SCREW PENETRATION * Modules in parallel. THESE 2 FIXINGS MUST ONLY TO BE USED IN CONJUNCTION WITH THE PRIMARY FIXINGS 15.00 110.00 GENERAL TOLERANCE Å} 0.5MM Other Lambda Modular Products SC150 150W up to 4 outputs Sirius 250W to 350W up to 6 outputs NV350 350W up to 6 outputs For Additional Information, please visit Vega 450W to 900W up to 10 outputs www.lambdapower.com/products/alpha-series.htm Alpha1500 1500W up to 16 outputs 3055 Del Sol Blvd • San Diego, CA 92154 • 1-800-LAMBDA-4 Revision A3: Mar 2005 4 S Siin ng glle e O Ou uttp pu utts s D Du ua all 175.50 50.00 115.50 30.00 12.00 34.00 7 OUTPUT MODULE SLOTS