GPFC250 Commercial/GPFM250 Medical 250 Watt Global Performance Switchers FEATURES: 3.6 watts/cu.in. power density Compact size (5.0" x 8.0" x 1.75") Power factor corrected to IEC 1000-3-2, Class A Less than 300 µA leakage Conducted EMI exceeds FCC Class B and CISPR 22 Class B (Commercial models) and CISPR 11 Class B (Medical models) Commercial Approved to UL1950, IEC950, EN60950 and CSA 22.2 No. 950 Medical Approved to UL2601-1, IEC601-1/60601-1 and CSA-C22.2 No. 601.1 2-year warranty marked to LVD SPECIFICATIONS: Ac Input 85-264 Vac, 47-63 Hz single phase. EMI/EMC Compliance All models include built-in EMI filtering to meet emissions Input Current requirements: Maximum input current 3.7 A at 90 Vac, 60 Hz with EMI SPECIFICATIONS COMPLIANCE LEVEL full rated load. Input current harmonic content meets Conducted Emissions GPFC250 EN55022 Class B; FCC Class B the requirements of IEC1000-3-2 Class A for all Conducted Emissions GPFM250 EN55011 Class B; FCC Class B load conditions. Static Discharge EN61000-4-2, 6 kV contact, 8 kV air Hold-upTime RF Field Susceptibility EN61000-4-3, 3 V/meter 25 ms minimum from loss of ac input at full load, nominal Fast Transients/Bursts EN61000-4-4, 2 kV, 5 kHz line (115 Vac). Surge Susceptibility EN61000-4-5, 1 kV diff., 2 kV com. Minimum Load: No minimum load required Inrush Current Output Power Inrush 240 Vac is less than 37 A, averaged over the first 250 W fan cooled, 180 W convection ac half-cycle under cold start conditions. Limiting pro- vided by internal thermistors. Overload Protection Fully protected against short circuit and output overload. Fan Output Short circuit protection is cycling type power limit or An additional 12 Vdc, 250 mA output suitable for power- foldback type depending on model and output. Recovery ing a dc fan is included in all models. after fault is automatic. Individual output current limits are Thermal Shutdown a function of load distribution and degree of overload. Provided as a standard feature. Designed to protect unit Output Noise from prolonged over temperature. 0.5% rms, 1% pk-pk, 20 MHz Bandwidth, differential Power Fail mode. Measured with noise probe directly across output TTL or CMOS compatible output goes low (<0.5 V) 8 ms terminals of the power supply. before output voltage drops more than 4% below nominal Transient Response voltage upon loss of ac power. The signal is factory set to Main Output–500 ms typical response time for return to trip when input power can no longer sustain the output. within 0.5% of final value for a 50% load step change, Di/ Temperature Coefficient Dt< 0.2 A/ms. Maximum voltage deviation is 3.5%. Load 0.03% / °C typical on all outputs. must not go below stated minimum. Leakage Current Remote Sense 70µA under normal conditions (132 Vac @ 60 Hz). Provided as a standard feature. Capable of compensating Maximum under single fault conditions (254 Vac @ 50 for 0.25 V total of cabling losses in voltage. Hz), 130 µA. Overvoltage Protection Power Good Built in on all models. Output voltage decay is dependent TTL/CMOS compatible output goes high more than 100 upon loading. ms after V1 reaches the under voltage threshold and Voltage Adjustment should assure that sufficient energy is stored in the input Main output ±5%. section to provide normal power fail/shutdown. The signal will fall to a low state (<0.5 V) when V1 goes below 95% Efficency of the rated voltage. Minimum 80% on 12-48 V units, 75% on 5 & 3.3 V units at full rated load. External Off Input Protection TTL/CMOS compatible input shuts down power converter. Internal ac fuses provided on all models. Fuses do not A logic high (>2.7 V with 400 uA source) shuts down the blow on overload or short circuit—fuses blow only if power converter. A logic low (<0.5 V) or an open circuit catastrophic failure occurs in the unit. allows the supply to run. Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929 • 805-486-4565  FAX 805-487-8911  www.condorpower.com 68 GPFC250 Commercial/GPFM250 Medical 250 Watt Single Output Commercial Medical Voltage Output Output Model Model Output No. Output Adjustment Maximum (A) Peak (B) OVP Setpoint Total Regulation Notes GPFC250-3.3 GPFM250-3.3 1V3% .3 ±A 5 3A 6 5V 06% .2 ± 0.6 2C GPFC250-5 GPFM250-5 1V5% .1 ±A 5 3A 6 5V 06% .2 ± 0.6 2C GPFC250-12 GPFM250-12 1V1% 2 ±A 5 1A 5 2V 1 1% 4 ± 1.1 2C GPFC250-15 GPFM250-15 1V1% 5 ±A 5 1A 2 1V 6.71% 8.5 ± 1.5 2C GPFC250-24 GPFM250-24 1V2% 4 ±A 5 7A .5 1V 0.52% 8 ± 2.5 2C GPFC250-28 GPFM250-28 1V2% 8 ±A 5 6A .5 9V3% 4 ± 2.8 2C GPFC250-48 GPFM250-48 1V4% 8 ±A 5 3A .8 5V .35% 5 ± 4.0 2C A. Output rating with unrestricted convection cooling. B. Output rating with 26cfm airflow. C. Add “C” suffix for factory installed cover with fan option. GPFC250/GPFM250 MECHANICAL SPECIFICATIONS INPUT: TB1 6-32, 3 PIN TERMINAL BLOCK PIN 1) AC LINE PIN 2) AC NEUTRAL PIN 3) AC GROUND SIGNALS: J2 AMP P.C.B. HEADER P/N 640456-5 MATING CONNECTOR P/N640440-5 PIN 1) DC GOOD PIN 2) POWER FAIL PIN 3) EXT OFF PIN 4) +SENSE PIN 5) -SENSE FAN AMP P.C.B. HEADER P/N 640456-2 MATING CONNECTOR P/N 640440-2 PIN 1) - PIN 2) + OUTPUT: TB2 6-32, 4 PIN TERMINAL BLOCK 0.375 [9.53mm]CTR AN OPTIONAL BUS BAR WITH 10-32 SCREWS ON HIGH-CURRENT MODELS IS AVAILABLE BY ADDING -B TO MODEL NUMBER PINS 1-2) +Vout PINS 3-4) RETURN 16A MAXIMUM RECOMMENDED CURRENT PER CONNECTOR PIN. MAX. SCREW PROTRUSION ABOVE CHASSIS =0.120” [3.05MM]. OPTIONAL: COVER/FAN ASSEMBLY #09-250CF CAN BE INCLUDED BY ADDING -C TO MODEL NUMBER WEIGHT: 2.9 LBS. [1.32 kg] MAX. TOLERANCES: X.XX=0.030 [0.76mm] X.XXX+0.010 [0.25 mm] Environmental Operating Non-operating Specification o o T0 emperature (A) 0 to 5C5 -40 to +8 C HH umidity (A)0H to 95% R 0 to 95% R A. Units should be allowed to warm up/operate under non-condensing conditions before application of power. Derate output current and total output power by 2.5% Sg hock (B) 20 40 g per °C above 50°C. pk pk B. Random vibration—10 to 2000Hz, 6dB/octave roll-off from 350 to 2000Hz, 3 At ltitude-t 500 to 10,000 f -500 to 40,000 f orthogonal axes. Tested for 10 min./axis operating and 1 hr./axis non-operating. 2 2 Vg ibration (C) 1.5 , 0.003 g/g Hz 5 , 0.026 g /Hz C. Shock testing—half-sinusoidal, 10 ± 3 ms duration, ± direction, 3 orthogonal axes, rms rms total 6 shocks. Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com 69