GLC75 Commercial/GLM75 Medical 75 Watt Multiple Output Global Performance Switchers FEATURES: Cost-effective multiple output power source Universal input 90-264 Vac 7.00”x 4.25”x 1.30” (Meets 1U height) 2-year warranty Conducted EMI exceeds FCC Class B and CISPR 22 Class B (Commercial models) and CISPR 11 Class B (Medical models) Complies with EN61000-3-2 Class A Also available in single output versions Commercial UL1950, CSA22.2 No. 234 and IEC950 and EN60950 approvals Medical Approved to UL2601-1, IEC601-1 and CSA-C22.2 No. 601.1 SPECIFICATIONS: marked to LVD Ac Input 90-264 Vac, 47-63 Hz single phase. Input Protection Input Current Internal ac fuse provided on all units. Designed to blow Maximum input current at 120 Vac, 60 Hz with full rated only if a catastrophic failure occurs in the unit. output load not to exceed 2.3 A. Inrush Current Output Power Inrush limited by internal thermistors. Inrush at 240 Vac, Normal continuous output power is 75 W for unrestricted averaged over the first ac half-cycle under cold start natural convection cooling. The standard power is 110 W conditions will not exceed 37 A. with 26 cfm airflow. During peak load conditions output regulation may exceed total regulation and noise limits. Hold Up Time 20 ms minimum from loss of ac input power at full load, Output Regulation nominal line (120 Vac). Measured by ±40% load change from 60% rated load with all other outputs at 60% rated load and input voltage Temperature Coefficient change from minimum to maximum ratings. Output #1 0.03%/°C typical on all outputs. requires 20% minimum load for proper regulation of other outputs. Initial set tolerance is measured with all outputs at Power Fail 60% of full rated load. Output #2 requires 0.5 a minimum A standard TTL or CMOS compatible output goes low load for proper regulation. (< 0.5 V) 5ms before output voltage drops more than 4% below nominal voltage upon loss of ac power. Signal is Overload Protection factory set to trip on 84 to 94 Vac brown-out depending Factory set to begin power limiting at approximately 120 W. upon incoming line impedance and distortion. Other Fully protected against short circuit and output overload. settings are available through adjustment of built-in Short circuit protection is cycling type power limit. potentiometer (consult factory for assistance). Output will stay low for 20 ms minimum. Output Noise 0.5% rms, 1% pk-pk, 20 MHz bandwidth, differential mode. EMI/EMC Compliance Measured with noise probe directly across output terminals All models include built-in EMI filtering to meet the of the power supply. following emissions requirements: Transient Response EMI SPECIFICATIONS COMPLIANCE LEVEL Main Output: 500µSec typical response time for return to Conducted Emissions-GLC75 EN55022 Class B; FCC Class B within 0.5% of final value for a 50% load step change, Δi/ Conducted Emissions-GLM75 EN55011 Class B; FCC Class B Δt<0.2A/µSec. Maximum voltage deviation is 3.5%. Static Discharge EN61000-4-2, 6 kV contact, 8 kV air RF Field Susceptibility EN61000-4-3, 3 V/meter Overvoltage Protection Fast Transients/Bursts EN61000-4-4, 2 kV, 5 kHz Built in on V1 with firing point set per table. OVP firing Surge Susceptibility EN61000-4-5, 1 kV diff., 2 kV com. reduces output #1 and #2 to less than 50% of nominal Line Frequency Harmonics EN61000-3-2 Class A voltage in 50 ms. Commercial Safety Voltage Adjust All GLC models are approved to UL1950, CSA22.2 No. Factory set on standard unit; however, optional potentiom- 234 Level 3, IEC950 and EN60950. Consult factory for eter adjusts voltage from 4.7 V to OVP point (6.2 V nominal) approval status. on the +5 V output. Note: Output #1 must not be more than 1% below nominal to achieve full output voltage range on Medical Leakage Current Output #2. Output regulation limits in some models may be 70 µA 264 V @ 50 Hz (normal conditions). exceeded when the main output is adjusted beyond +1% of nominal voltage. High voltage settings may degrade the Medical Safety reliability of the unit due to excessive power dissipation in All GLM models are approved to UL2601-1, CSA-C22.2 some outputs. No. 601.1, IEC601-1 and EN60601. Consult factory for Efficiency approval status. 68% -78% depending on model and load distribution. Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929 • 805-486-4565  FAX 805-487-8911  www.condorpower.com 42 GLC75 Commercial/GLM75 Medical 75 Watt Multiple Output Commercial Medical Output Maximum Output Maximum Output Minimum Model Model Output No. Output (A) (B) Output Peak V1 OVP Set Noise P-P Regulation GLC75A GLM75A 1V+A 5.1 1A8A1A 0 1V 2 6V .2 ± 0.6 5% 0 m 2 2V+A 12 0A .5 2A .5 3A4V1) 20 m +10%, -5% (D 3V-A 12 0A1A1A1V .2 1% 20 m 3 4V+A 12 0A2A .5 3A4V1% 20 m 2 GLC75B GLM75B 1V+A 5.1 1A8A1A 0 1V 2 6V .2 ± 0.6 5% 0 m 2 2V+A 12 0A .5 2A .5 3A4V1) 20 m +10%, -5% (D 3V-A 5 0A1A1A1V .2 5% 0 m 3 4V+A 12 0A2A .5 3A4V1% 20 m 2 GLC75C GLM75C 1V+A 5.1 1A8A1A 0 1V 2 6V .2 ± 0.6 5% 0 m 2 2V+A 12 0A .5 2A .5 3A4V1) 20 m +10%, -5% (D 3V-A 15 0A1A1A1V .2 1% 50 m 3 4V+A 15 0A2A .5 3A4V1% 50 m 2 GLC75D GLM75D 1V+A 5.1 1A8A1A 0 1V 2 6V .2 ± 0.6 5% 0 m 2 2V+A 24 0A .5 2A .5 2A .53V .5 2) 40 m +10%, -5% (D 3V-A 12 0A1A1A1V .2 1% 20 m 3 4V+A 12 0A2A .5 3A4V1% 20 m 2 GLC75E GLM75E 1V+A 5.1 1A8A1A 0 1V 2 6V .2 ± 0.6 5% 0 m 2 2V+A 24 0A .5 2A .5 2A .53V .5 2) 40 m +10%, -5% (D 3V-A 15 0A1A1A1V .2 1% 50 m 3 4V+A 15 0A2A .5 3A4V1% 50 m 2 GLC75F GLM75F 1V+A 5.1 1A8A1A 0 1V 2 6V .2 ± 0.6 5% 0 m 2 2V+A 15 0A .5 2A .5 3A4V1) 50 m +10%, -5% (D 3V-0 5 1A A 1A1V .2 5% 0 m 3 4V-0 15 2A .5A 3A4V1% 50 m 2 GLC75H GLM75H 1V+A 5.1 1A8A1A 0 1V 2 6V .2 ± 0.6 5% 0 m 2 2V+A 15 0A .5 2A .5 3A4V1) 50 m +10%, -5% (D 3V-0 15 1AA 1A1V .2 1% 50 m 3 4V+0 15 2A .5A 3A4V1% 50 m 2 GLC75J GLM75J 1V+A 5.1 1A8A1A 0 1V 2 6V .2 ± 0.65% 0 m 2 2V+A 12 0A .5 2A .5 3A4V1) 20 m +10%, -5% (D 3V-0 12 1AA 1A1V .2 1% 20 m 3 4V (C) 50 2A .0A 3A4V5% 0 m 2 GLC75P GLM75P 1V+A 5.1 1A8A1A 0 1V 2 6V .2 ± 0.65% 0 m 2 2V+A 24 0A .5 4A4A4V .5 2) 40 m +10%, -5% (D 3V-A 12 0A1A1A1V .2 1% 20 m 3 4V+A 12 0A2A .5 3A4V1% 20 m 2 A. Rating with unrestricted convection cooling. Total power not to exceed 75 W. B. Rating with 26 cfm forced-air cooling. Total power not to exceed 110 W. C. Floating fourth output can be referenced as either positive or negative. Connect pin 12 to Return to provide a positive voltage at Pin 13. Connect pin 13 to Return to provide a negative voltage at Pin 12. D. To maintain these regulations conditions, the +5V current must be at least 1/5 of V2 and not greater than 5 times the V2 current. Requires +5V to be adjusted to within 1% with at least a 1 A load to maintain regulation on this output. GLC75/GLM75 MECHANICAL SPECIFICATIONS Environmental Operating Non-operating Specification o o T0 emperature (A) 0 to 5C5 -40 to +8 C A. Units should be allowed to warm up/operate under non-condensing conditions before application of power. Derate output current and total output power by 2.5% HH umidity (A)0H to 95% R 0 to 95% R per °C above 50°C. Sg hock (B) 20 40 g pk pk B. Random vibration—10 to 2000Hz, 6dB/octave roll-off from 350 to 2000Hz, 3 orthogonal axes. Tested for 10 min./axis operating and 1 hr./axis non-operating. At ltitude-t 500 to 10,000 f -500 to 40,000 f C. Shock testing—half-sinusoidal, 10 ± 3 ms duration, ± direction, 3 orthogonal axes, 2 2 Vg ibration (C) 1.5 , 0.003 g/g Hz 5 , 0.026 g /Hz total 6 shocks. rms rms Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com 43