GPC41 Commercial/GPM41 Medical 41 Watt Global Performance Switchers FEATURES: Ultra small (2.00" x 4.00" x 1.50") Wide-range ac input 85-264 Vac 2-year warranty Conducted EMI exceeds FCC Class B and CISPR 22 Class B (Commercial models) and CISPR 11 Class B (Medical models) Commercial Approved to UL1950, IEC950, EN60950 and CSA22.2-234 L3 Medical Approved to UL2601-1, IEC601-1 and CSA22.2 No. 601 marked to LVD SPECIFICATIONS: Ac Input 85-264 Vac, 47-63 Hz single phase. Input Current Output Noise Maximum input current at 120 Vac, 60 Hz with full rated 0.5% rms, 1% pk-pk, 20 MHz bandwidth, differential output load: 1.3 A mode. Measured with noise probe directly across output terminals of the power supply. Hold-Up Time 20 ms minimum from loss of ac input at full load, nominal Transient Response line (115 Vac). Main output—500 µs typical response time for return to within 0.5% of final value for a 50% load step change. Δi/ Output Power Δt<0.2 A/µs. Maximum voltage deviation is 3.5%. Startup/ 40 W continuous, 50 W peak. Peak ratings are for 60 s shutdown overshoot less than 3%. maximum duration, 10% duty cycle. During peak load condition, output regulation may exceed total regulation EMI/EMC Compliance limits. All models include built-in EMI filtering to meet the following emissions requirements: Overload Protection Fully protected against short circuit and output overload. EMI SPECIFICATIONS COMPLIANCE LEVEL Short circuit protection is cycling type power limit. Conducted Emissions GPC41 EN55022 Class B; FCC Class B Recovery after fault is automatic. Factory set to begin Conducted Emissions GPM41 EN55011 Class B; FCC Class B power limiting at approximately 55 W. See output ratings Static Discharge EN61000-4-2, 6 kV contact, 8 kV air chart for additional notes or conditions. RF Field Susceptibility EN61000-4-3, 3 V/meter Fast Transients/Bursts EN61000-4-4, 2 kV, 5 kH Overvoltage Protection Surge Susceptibility EN61000-4-5, 1 kV diff., 2 kV com. See output ratings chart. Commercial Leakage Current Efficiency 60 µA single fault; 60 Hz input. 69-77% at full rated load, nominal input voltage, depend- ing on model. Commercial Safety Approved to UL1950, CSA22.2 No. 234 Level 3, IEC950 Turn-on Time and EN60950. UL file #E135803 commercial; CSA Less than 1 s at 120 Vac, 25°C (inversely proportional to #LR46516 all models. The output is intended for safety input voltage). earthed Signal Output and Intermediate Circuits only. All dc outputs are SELV under normal and single fault Input Protection conditions. Requires external ac line fusing. A 2.5 A, 250 V rated fuse 2 with I t > 20 is recommended. Medical Leakage Current 35 µA , 254 Vac 10 Hz input. Inrush Current Inrush is limited by internal thermistor. Inrush at 240 Vac Medical Safety under cold start conditions will not exceed 34 A. Approved to UL2601, CSA22.2 No. 601 Level 3, IEC601. UL file E116994; CSA #LR46516. The output(s) are Temperature Coefficient intended for safety earthed Signal Output and Intermedi- 0.03%/°C typical on all outputs. ate Circuits only. The output(s) are not acceptable for patient connection without additional isolation. All dc Environmental outputs are SELV under normal and single fault condi- Designed for 0 to 50°C operation at full rated output tions. power; derate output current and total output power by 2.5% per °C above 50°C. See Environmental and Packaging Specifications on next page. Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929 • 805-486-4565  FAX 805-487-8911  www.condorpower.com 28 GPC41 Commercial/GPM41 Medical 41 Watt Single Output Commercial Medical Minimum Load Initial Setpoint OVP Model Model Output Current Load Regulation Tolerance Setpoint Ripple and Noise GPC41-5 GPM41-5 5A .1 V 65 .0 0% .1 0% .75 2V6% .2 ± 0.6 1 GPC41-12 GPM41-12 1A 2 V 33 .3 0% .0 0% .75 2V1% 4 ± 1.0 1 GPC41-15 GPM41-15 1A 5 V 23 .7 0% .0 0% .75 2V1% 9 ± 1.5 1 GPC41-24 GPM41-24 2A 4 V 11 .7 0% .0 0% .75 2V2% 8 ± 2.5 1 GPC41-28 GPM41-28 2A 8 V 11 .4 0% .0 0% .75 2V3% 4 ± 2.8 1 GPC41/GPM41 MECHANICAL SPECIFICATIONS Environmental Operating Non-operating Specification o Ts emperature (A)S5 ee individual spec -40 to +8 C HH umidity (A)0H to 95% R 0 to 95% R A. Units should be allowed to warm up/operate under non-condensing conditions Sg hock (B) 20 40 g before application of power. pk pk B. Random vibration—10 to 2000Hz, 6dB/octave roll-off from 350 to 2000Hz, 3 At ltitude-t 500 to 10,000 f -500 to 40,000 f orthogonal axes. Tested for 10 min./axis operating and 1 hr./axis non-operating. C. Shock testing—half-sinusoidal, 10 ± 3 ms duration, ± direction, 3 orthogonal axes, 2 2 Vg ibration (C) 1.5 , 0.003 g/g Hz 5 , 0.026 g /Hz rms rms total 6 shocks. Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com 29