GLC110 Commercial/GLM110 Medical 110 Watt Global Performance Switchers FEATURES: Cost-effective power source Single- and multiple-output units Low height (1.30") 2-year warranty Power fail signal standard Commercial Approved to UL1950, IEC950 CSA22.2 No. 234 Medical Approved to UL2601-1, EN60601, CSA-C22.2 No. 601.1 Complies with EN61000-3-2 Class A marked to LVD Other settings are available to the user through adjust- SPECIFICATIONS: ment of built in potentiometer (consult factory for assis- Ac Input tance). Output will stay low for 20 ms minimum. 90-264 Vac, 47-63 Hz single phase. Input Current Transient Response Main Output: 500 µs typical response time for return to Maximum input current at 90 Vac, 60 Hz with full rated output load not to exceed 2.9 A. within 0.5% of final value for a 50% load step change, Δi/ Δt<0.2 A/µs. Maximum voltage deviation is 3.5%. Startup/ Hold-up Time shutdown overshoot less than 3%. Turn-On Time 20 ms minimum from loss of ac input at full load, nominal line (120 Vac). Less than 1 second at 120 Vac, 25 Overvoltage Protection Output Power Built in on main output. Normal continuous output power is 75 W for unrestricted natural convection, or 110 W with 26 cfm air flow. Efficiency 72-85% depending on model. Output Regulation Load regulation on dual output models is measured by Input Protection ±40% load change from 60% rated load and input voltage change from minimum to maximum ratings. Internal ac fuse provided on all units. Designed to blow only if a catastrophic failure occurs in the unit. Output #1 requires 1A minimum load for proper regula- tion of other outputs. Initial set tolerance is measured with Inrush Current all outputs at 60% of full rated load. Load regulation for single-output models measured by changing load from Inrush limited by internal thermistors. Inrush at 240 Vac, averaged over the first ac half-cycle under cold start 5% to 50% load or 50% to full load in either direction. conditions will not exceed 37 A. Voltage Adjustment Output #1 adjustment is ±5%. Note: output #1 must not be Temperature Coefficient 0.03%/°C typical on all outputs. more than 1% below nominal to achieve full output regulation on output #2. High voltage settings may degrade the reliability of the unit due to excessive power EMI/EMC Compliance dissipation in some outputs. All models include built-in EMI filtering to meet the following emissions requirements: EMI SPECIFICATIONS COMPLIANCE LEVEL Overload Protection Fully protected against short circuit and output overload. Conducted Emissions GLC110 EN55022 Class B; FCC Class B Conducted Emissions GLM110 EN55011 Class B; FCC Class B Short circuit protection is cycling type power limit. Factory set to begin power limiting at 120 W. Static Discharge EN61000-4-2, 6 kV contact, 8 kV air RF Field Susceptibility EN61000-4-3, 3 V/meter Output Noise Fast Transients/Bursts EN61000-4-4, 2 kV, 5 kHz Surge Susceptibility EN61000-4-5, 1 kV diff., 2 kV com. 0.5% rms, 1% pk-pk, 20 MHz bandwidth, differential mode. Measured with noise probe directly across output Line Frequency Harmonics EN61000-3-2 Class A terminals of the power supply. Commercial Safety All GLC models are approved to UL1950, CSA22.2 No. POWER FAIL Power fail signal is TTL or CMOS compatible (output goes 234 Level 3, IEC950 and EN60950. Consult factory for approval status. low <0.5 V) 5 ms before output voltage drops more than 4% below nominal voltage upon loss of AC power. The signal is factory set to trip on 84 to 94 Vac brown-out Medical Safety depending upon incoming line impedance and distortion. All GLM models are approved to UL2601-1, CSA-C22.2 No. 601.1, IEC601-1/60601-1. Consult factory for approval status. Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929 • 805-486-4565  FAX 805-487-8911  www.condorpower.com 46 GLC110 Commercial/GLM110 Medical 110 Watt Single & Dual Output Commercial Medical Output Output Forced Total Model Model Output No. Output Minimum Normal (A) Air (B) Output Peak Noise P-P OVP Regulation(C) GLC110-212 GLM110-212 1 +12 V 1 A 6.3 A 9.1 A 9.5 A 100 mV 15.6 ± 1.1 V 2% 2 -12 V 0 A 2.5 A 3 A 4 A 120 mV 2% GLC110-215 GLM110-215 1V+A 15 1A5A7A .3 7V .71V 20 m1% 8.5 ± 1.5 2 2V-A 15 0A2A .5 3A4V1% 50 m 2 GLC110-524 GLM110-524 1V+A 24 1A3A .2 4A .6 4V .752V 00 m2% 8 ± 2.5 2 2V+A 5 0A1A .5 2A2V .5 5V 0 m6% .2 ± 0.6 2 GLC110-12 GLM110-12 1V1A 2 0A6A .3 9A .1 9V .51V 20 m1% 5.6 ± 1.1 2 GLC110-15 GLM110-15 1V1A 5 0A5A7A .3 7V .71V 50 m1% 8.5 ± 1.5 2 GLC110-24 GLM110-24 1V2A 4 0A3A .2 4A .6 5V2V 40 m2% 8 ± 2.5 2 A. Rating with unrestricted convection cooling. Total power not to exceed 75 W; no output can exceed rated current. B. Rating with 26 cfm forced air cooling. Total power not to exceed 110 W. C. To maintain regulation V1 current must be at least 1/5 of V2. V1 must not be adjusted more than 1% below nominal and have at least 10% of rated load. GLC110/GLM110 MECHANICAL SPECIFICATIONS Environmental Operating Non-operating Specification o o T0 emperature (A) 0 to 5C5 -40 to +8 C HH umidity (A)0H to 95% R 0 to 95% R A. Units should be allowed to warm up/operate under non-condensing conditions before application of power. Derated output current and toal output power by 2.5% Sg hock (B) 20 40 g per ºC above 50ºC. pk pk B. Random vibration—10 to 2000Hz, 6dB/octave roll-off from 350 to 2000Hz, 3 At ltitude-t 500 to 10,000 f -500 to 40,000 f orthogonal axes. Tested for 10 min./axis operating and 1 hr./axis non-operating. C. Shock testing—half-sinusoidal, 10 ± 3 ms duration, ± direction, 3 orthogonal axes, 2 2 Vg ibration (C) 1.5 , 0.003 g/g Hz 5 , 0.026 g /Hz rms rms total 6 shocks. Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com 47