GLC65 Commercial/GLM65 Medical 65 Watt Single Output Global Performance Switchers FEATURES: 3 4.1 W/in Compact (3.0" x 5.0" x 1.06") Ultra-high efficiency (up to 94%) using patented technology Meets harmonic requirements of IEC1000-3-2, Class A Conducted EMI exceeds FCC Class B and CISPR 22 Class B (Commercial models) and CISPR 11 Class B (Medical models) 2-year warranty Exempt from line harmonics standard EN61000-3-2 Commercial Approved to UL1950, IEC950, EN60950, CSA22.2 No. 950 Medical Approved to UL2601, EN60601, CSA22.2 SPECIFICATIONS: No. 601.1 Multiple output versions also available Ac Input 90-264 Vac, 47-63 Hz single phase.marked to LVD Input Current Maximum input current at minimum output voltage and output overload will be less than 1.7 A. Meets input current harmonic requirements of IEC1000-3-2. Inrush Current Output Power Inrush is limited by internal thermistor. The inrush at 240 Normal continuous output power is 65 W, 75 W peak for Vac, averaged over the first ac half-cycle under cold start 60 s. The 3.3 Vdc unit is 36.3 W and the 5 Vdc unit is 55 W conditions will not exceed 37A. continuous. EMI/EMC Compliance Hold-Up Time All models include built-in EMI filtering to meet the 20 ms from loss of ac input at 65 W load, from 120 Vac following emissions requirements: input. EMI SPECIFICATIONS COMPLIANCE LEVEL Conducted Emissions GLC65 EN55022 Class B; FCC Class B Overload Protection Conducted Emissions GLM65 EN55011 Class B: FCC Class B Fully protected against short circuit and output overload. Static Discharge EN61000-4-2, 6 kV contact, 8 kV air Short circuit protection is cycling type power limit. RF Field Susceptibility EN61000-4-3, 3 V/meter Fast Transients/Bursts EN61000-4-4, 2 kV, 5 kHz Output Noise Surge Susceptibility EN61000-4-5, 1 kV diff., 2 kV com. 0.5% rms, 1% pk-pk, 20 MHz bandwidth, differential mode. Measured with scope probe directly across output Commercial Leakage Current terminals of the power supply with load terminated with Under normal conditions, leakage current is 425 µA with 0.1 µF capacitor. 132 Vac @ 60 Hz input. Transient Response Commercial Safety Main output: 500 µs typical response time for return to All GLC models are approved to UL1950, CSA22.2 No. within 0.5% of final value for a 50% load step within the 950, IEC950 and EN60950. regulation limits of minimum and maximum load, Δi/Δt<0.2 A/µs. Maximum voltage deviation is 3.5%. Medical Leakage Current Startup/shutdown overshoot less than 3%. The maximum leakage current under single-fault condi- tions (254 Vac @ 50 Hz) is 120 µA. Under normal Voltage Adjustment conditions, leakage current is 31µA with 132 Vac @ 60 Hz Adjustable potentiometer capable of ±5% change from input. nominal setting. Medical Safety Efficiency All GLM models are approved to UL2601, CSA22.2 No. 82 to 94% minimum at full rated load, nominal input 601, IEC601-1 and EN60601. Consult factory for approval voltage, depending on model. status. Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929 • 805-486-4565  FAX 805-487-8911  www.condorpower.com 36 GLC65 Commercial/GLM65 Medical 65 Watt Single Output Commecial Medical Output Current Total Regulation V1 Adjustment V1 OVP Setpoint Ripple and Noise Model Model GLC65-5 GLM65-5 5A .1 V 1% 1 2%±V 5 6% .2 ± 0.6 1 GLC65-12 GLM65-12 1A 2 V 5% .5 2%±V 5 1% 4 ± 1.1 1 GLC65-15 GLM65-15 1A 5 V 4% .3 2%±V 5 1% 8.5 ± 1.5 1 GLC65-18 GLM65-18 1A 8 V 3% .6 2%±0 5 2% 1.7 ± 2. 1 GLC65-24 GLM65-24 2A 4 V 2% .7 2%±V 5 2% 8 ± 2.5 1 GLC65-28 GLM65-28 2A 8 V 2% .3 2%±V 5 3% 4 ± 2.8 1 GLC65-48 GLM65-48 4A 8 V 1% .35 2%±V 5 5% 5 ± 4.0 1 GLC65/GLM65 MECHANICAL SPECIFICATIONS Environmental Operating Non-operating Specification o o T0 emperature (A) 0 tp 5C5 -40 to +8 C A. Units should be allowed to warm up/operate under non-condensing conditions HH umidity (A)0H to 95% R 0 to 95% R before application of power. Derate output current and total output power by 2.5% Sg hock (B) 20 40 g per °C above 50°C. pk pk B. Random vibration—10 to 2000Hz, 6dB/octave roll-off from 350 to 2000Hz, 3 At ltitude-t 500 to 10,000 f -500 to 40,000 f orthogonal axes. Tested for 10 min./axis operating and 1 hr./axis non-operating. C. Shock testing—half-sinusoidal, 10 ± 3 ms duration, ± direction, 3 orthogonal axes, 2 2 Vg ibration (C) 1.5 , 0.003 g/g Hz 5 , 0.026 g /Hz rms rms total 6 shocks. Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com 37