RAD TECHNOLOGIES D8U
Specifications
Compliance
ITU-T Rec. G.961 ANSI T1.601
Configuration
Programmable by the DXC system management or RADview Management System. Downloading configuration of ASMi-31 from “1” port to the remote modem
Connector
25-pin D-type female connector per groupof eight ports
Indicators (per port)
SYNC LOSS (red) – On: line synchronization lost. TEST (yellow) – On: test running on line.
Line Signal Format
2B1Q
Line Type
2-wire unconditioned telephone loops (one twisted pair)
Maximum Loop Loss
42 dB at 40 kHz, max resistance 1300O
Nominal Data Rate
160 kbps (ISDN basic rate access, 2B + D channels)
Nominal Line Impedance
135O
Number of Ports
8 “U” ports
Phantom Feeding
96 VDC provided by an external source connected to the module connector, can be individually enabled/disabled for each module port
Physical
Occupies a single slot in a DXC-8R, DXC-10A or DXC-30 chassis
Port Payload Rate
“I” configuration: 64 kbps on each B channel, 16 kbps on each D channel. “1” configuration: 64 or 128 kbps.
Port Timing
LT Mode: Transmit timing is locked to the DXC nodal timing. NT Mode: Receive timing is recovered from line signal
Power Consumption
6W at 1.2A maximum
Transmission Format
Full-duplex
Transmit Level
+13 dBm
Typical Range
5.5 km (3.4 miles) over 26 AWG (0.4 mm) pair
Features
- Full interoperability with Megaplex-2100/2104 HS-U family modules
- ISDN line extension or dedicated line termination units for leased lines
- ITU-T Rec. G.961 compliant
- Per port 2B + D channel transmission at ranges of up to 5.5 km (3.4 miles)
Datasheet
Extracted Text
Data Sheet DXC Module D8U 8-Port ISDN "U" Interface Module • Full interoperability with Megaplex-2100/2104 HS-U family modules • Per port 2B + D channel transmission at ranges of up to 5.5 km (3.4 miles) • ITU-T Rec. G.961 compliant • ISDN line extension or dedicated line termination units for leased lines D8U is an 8-port ISDN “U” interface D8U is fully interoperable with module for use with the modular DXC Megaplex-2100/2104 HS-U family Digital Cross-Connect units. modules. D8U provides ISDN “U” ports, each Each B channel or “U” interface can be supporting 2B + D channels, for a total programmed independently to operate at payload data rate of up to 128 kbps per the following data rates (depending on port. the application): 2B1Q line coding is used for full-duplex • “I” mode: 64 kbps data transmission over 2-wire • “1” mode: 64 or 128 kbps. unconditioned lines at ranges of up to D8U provides 96 VDC phantom feeding to 5.5 km (3.4 miles) over 26 AWG line. remote equipment. Received from an D8U can be configured to work in the external power source, the phantom following applications: feeding can be enabled or disabled for • Extension of ISDN lines over non-ISDN each module port. facilities (“I” mode). In this application Diagnostic functions include loopbacks on D8U can be configured as either line external ports and individual channels. termination (LT) or network 8-port ISDN “U” Additionally, when operating in “1” mode, termination (NT) unit, connecting up the modules can activate remote loopback to two remote locations. module for the DXC and BERT on the ASMi-31 modems via the • Line termination (“1” mode) over module ports. family of modular leased lines, with D channels disabled. Setup, control, and diagnostics are In this application D8U serves as performed via a DXC system supervisory cross-connects dedicated line termination unit for the port using an ASCII terminal, Telnet, or by ASMi-31 short-range modems, the RADview element management connecting up to 8 remote locations. system. The Access Company D8U 8-Port ISDN "U" Interface Module Figure 1. Extending ISDN Lines over Non-ISDN Facilities (“I” Mode) Figure 2. ISDL Application (“1” Mode) Data Sheet Typical Range Diagnostics (per port) Specifications 5.5 km (3.4 miles) over 26 AWG (0.4 mm) Local loopback Number of Ports pair Remote loopback 8 “U” ports Local loopbacks on the individual channels Connector of a port Compliance 25-pin D-type female connector per group Local loopback on module port in ITU-T Rec. G.961 ANSI T1.601 of eight ports response to RLB command Nominal Data Rate Phantom Feeding Remote loopback on remote ASM-31 or 160 kbps (ISDN basic rate access, 96 VDC provided by an external source ASMi-31, towards the module port 2B + D channels) connected to the module connector, can Activation of BER testing from remote be individually enabled/disabled for each ASM-31 or ASMi-31 towards the Line Signal Format module port module port 2B1Q Port Timing Indicators (per port) Transmission Format LT Mode: Transmit timing is locked to the SYNC LOSS (red) – Full-duplex DXC nodal timing On: line synchronization lost Line Type NT Mode: Receive timing is recovered from TEST (yellow) – 2-wire unconditioned telephone loops line signal On: test running on line (one twisted pair) Power Consumption Configuration Nominal Line Impedance 6W at 1.2A maximum Programmable by the DXC system 135Ω management or RADview Management Port Payload Rate System Transmit Level “I” configuration: Downloading configuration of ASMi-31 +13 dBm 64 kbps on each B channel from “1” port to the remote modem 16 kbps on each D channel Maximum Loop Loss “1” configuration: Physical 42 dB at 40 kHz, max resistance 1300Ω 64 or 128 kbps Occupies a single slot in a DXC-8R, DXC-10A or DXC-30 chassis For comparison of DXC chassis, see Table 2. For the list of DXC I/O modules, refer to the DXC-8R/10A/30 folder. 772-135-09/08 Specifications are subject to change without prior notice. 1988–2008 RAD Data Communications Ltd. The RAD name, logo, logotype, and the terms EtherAccess, TDMoIP and TDMoIP Driven, and the product names © Optimux and IPmux, are registered trademarks of RAD Data Communications Ltd. All other trademarks are the property of their respective holders. Data Sheet D8U 8-Port ISDN "U" Interface Module OPTIONAL ACCESSORIES Ordering CBL-D8U-RJ45/X DXC-M-8U Adapter cable for D8U, splits a single DB-25 connector into 8 x RJ-45 balanced connectors Table 2. DXC Chassis Comparison Table Feature DXC-8R DXC-10A DXC-30 DXC-100* Height 1U 1U 3U 6U per nest Maximum number of ports 32 40 120 688 (8 nests) Number of I/O slots 4 5 15 86 (8 nests) System redundancy Built-in None Optional Optional E1, T1, E3, T3, STM-1 modules 9 9 9 9 XDSL, inverse multiplexing modules 9 9 9 – n x 56/64 kbps modules 9 9 9 9 Router, OC-3 modules – – – 9 ASCII, SNMP, RADview management 9 9 9 9 *The DXC-8R/10A/30 modules and DXC-100 modules are not interchangeable. International Headquarters North America Headquarters 24 Raoul Wallenberg Street 900 Corporate Drive Tel Aviv 69719, Israel Mahwah, NJ 07430, USA Tel. 972-3-6458181 Tel. 201-5291100 Fax 972-3-6498250, 6474436 Toll free 1-800-4447234 E-mail market@rad.com Fax 201-5295777 E-mail market@radusa.com The Access Company www.rad. com
Frequently asked questions
How does Industrial Trading differ from its competitors?

Is there a warranty for the D8U?

Which carrier will Industrial Trading use to ship my parts?

Can I buy parts from Industrial Trading if I am outside the USA?

Which payment methods does Industrial Trading accept?

Why buy from GID?

Quality
We are industry veterans who take pride in our work

Protection
Avoid the dangers of risky trading in the gray market

Access
Our network of suppliers is ready and at your disposal

Savings
Maintain legacy systems to prevent costly downtime

Speed
Time is of the essence, and we are respectful of yours
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods