MODEL: M6SXV V2: Range -10 – +10 V DC Tension-Clamp Ultra-Slim Signal Conditioners M6S Series V3: Range -5 – +5 V DC (Configurator software is used to change output over the SIGNAL TRANSMITTER described range of the selected suffix code. (PC programmable) For changing between suffix codes, set the Output Range Functions & Features Selector on the side of unit before software adjustment.) • Maintenance-free tension clamp connection • 5.9-mm wide ultra-slim design POWER INPUT • Low profile allows the M6S module mounted in a 120-mm DC Power deep panel R: 24 V DC • Converts a DC input into a standard process signal (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) • PC programmable • High-density mounting • Power indicator LED [3] OPTIONS • UL approval STANDARDS & APPROVALS blank: CE marking 5.9 (.23) /UL: UL approval (CE marking) RELATED PRODUCTS • PC configurator software (model: M6CFG) 94 (3.70) Downloadable at M-System’s web site. A dedicated cable is required to connect the module to the PC. Please refer to the internet software download site or the users manual for the PC configurator for applicable 102 (4.02) cable types. mm (inch) GENERAL SPECIFICATIONS Connection MODEL: M6SXV–[1][2]–R[3] Input and output: Tension clamp Power input: Via the Installation Base (model: M6SBS) or Tension clamp ORDERING INFORMATION Applicable wire size: 0.2 to 2.5 mm2, stripped length 8 mm • Code number: M6SXV-[1][2]-R[3] Housing material: Flame-resistant resin (black) Specify a code from below for each [1] through [3]. Isolation: Input to output to power (e.g. M6SXV-Z1Z1-R/UL) Overrange output: -2 – +102 % • Input range (e.g. 4 – 20 mA DC) (Negative current output is not available.) • Output range (e.g. 4 – 20 mA DC) Zero adjustment: -2 to +2% (PC programming) Span adjustment: 98 to 102% (PC programming) [1] INPUT Power LED: Green light turns on when the power is supplied. Current Status indicator LED: Orange LED; Flashing patterns Z1: Range 0 – 50 mA DC (Input resistance 24.9 Ω) indicate different operating status of the transmitter. Voltage Programming: Downloaded from PC; input type and range, S1: Range -1000 – +1000 mV DC (Input resistance 1 MΩ min.) output type and range, zero and span, user’s linearization S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.) table (max. 101 points, specified within -2 to +102% for (Configurator software is used to change the input type and both input and output), etc. precise range.) For detailed information, refer to the users manual for the PC configurator. [2] OUTPUT Configurator connection: 2.5 dia. miniature jack; Current RS-232C level Z1: Range 0 – 20 mA DC Voltage http://www.m-system.co.jp/ M6SXV SPECIFICATIONS ES-7982 Rev.4 Page 1/4 MODEL: M6SXV INPUT SPECIFICATIONS INSTALLATION • DC Current: Input resistor incoporated Power consumption: Approx. 0.5 W (If not specified, the input range is 4 – 20 mA DC.) Operating temperature: -20 to +55°C (-4 to +131°F) Input range: 0 – 50 mA DC Operating humidity: 30 to 90 %RH (non-condensing) Minimum span: 2 mA Mounting: Installation Base (model: M6SBS) or DIN rail Offset: Lower range can be any specific value within the Weight: 65 g (2.3 oz) input range provided that the minimum span is maintained. • DC Voltage PERFORMANCE in percentage of span Code S1 (narrow spans) Overall accuracy: Input accuracy + output accuracy Input range: -1000 – +1000 mV DC Inversely proportional to the span. Minimum span: 100 mV See CALCULATION EXAMPLES OF OVERALL ACURACY. Code S2 (wide spans) • Input accuracy: (% of max. input range) Input range: -10 – +10 V DC -1000 – +1000 mV : ±0.01 % Minimum span: 1 V -10 – +10 V : ±0.01 % Offset: Lower range can be any specific value within the 0 – 50 mA : ±0.02 % input range provided that the minimum span is maintained. • Output accuracy: ±0.04 % of max. output range If not specified, the input range is shown below. Temp. coefficient: ±0.01 %/°C (±0.006 %/°F) of max. span S1: 0 – 100 mV DC Response time: ≤ 0.5 sec. (0 – 90 %) S2: 1 – 5 V DC Line voltage effect: ±0.1 % over voltage range Insulation resistance: ≥ 100 MΩ with 500 V DC OUTPUT SPECIFICATIONS Dielectric strength: 2000 V AC @1 minute (input to output • DC CURRENT to power to ground) Output range: 0 – 20 mA DC Conformance range: 0 – 20.4 mA DC CALCULATION EXAMPLES OF OVERALL ACCURACY Minimum span: 1 mA [Example] Input Type -10 – +10 V, Input Range 1 – 5 V, Offset: Lower range can be any specific value within the Output Type -5 – +5 V, Output Range 1 – 5 V output range provided that the minimum span is • Input accuracy = Max. Input Range (20 V) / Span (4 V) × maintained. 0.01 % = 0.05 % Load resistance: Output drive 11 V max. • Output accuracy = Max. Output Range (10 V) / Span (4 V) (e.g. 4 – 20 mA: 550 Ω [11 V/20 mA]) × 0.04 % = 0.1 % If not specified, the output range is 4 – 20 mA DC. Accuracy= ±0.15 % • DC VOLTAGE Code V2 (wide spans) STANDARDS & APPROVALS Output range: -10 – +10 V DC CE conformity: Conformance range: -10.4 – +10.4 V DC EMC Directive (2004/108/EC) Minimum span: 1 V EN 61000-6-4 (EMI) Code V3 (narrow spans) EN 61000-6-2 (EMS) Output range: -5 – +5 V DC Approval: Conformance range: -5.2 – +5.2 V DC UL/C-UL nonincendive Class I, Division 2, Minimum span: 0.5 V Groups A, B, C, and D hazardous locations Offset: Lower range can be any specific value within the (ANSI/ISA-12.12.01, CAN/CSA-C22.2 No.213) output range provided that the minimum span is UL/C-UL general safety requirements maintained. (UL 61010-1, CAN/CSA-C22.2 No.61010-1) Load resistance: Output drive 1 mA max. (e.g. 1 – 5 V: 5000 Ω [5 V/1 mA]) If not specified, the output range is shown below. V2: 0 – 10 V DC V3: 1 – 5 V DC http://www.m-system.co.jp/ M6SXV SPECIFICATIONS ES-7982 Rev.4 Page 2/4 MODEL: M6SXV EXTERNAL VIEW � FRONT VIEW (with the cover open) � SIDE VIEW 5 6 7 8 Power LED Output Range Selectors Status Indicator LED Configurator Jack 1 2 3 4 The DIP switch setting is required to select output types before setting a precise output range using PC Configurator Software (model: M6CFG). Refer to the instruction manual for detailed procedures. DIMENSIONS unit: mm (inch) SCREWDRIVER * INSERTION ANGLE : approx. 35° WIRE INSERTION ANGLE TEST PROBE : approx.35° max. 2 (.08) dia. 5 6 7 8 DIN RAIL HOOK DIN RAIL 35mm wide 1 2 3 4 SCREWDRIVER [0.5 (.02)] INSERTION ANGLE : approx. 40° 5.9 (.23) 102 (4.02) • When mounting, no extra space is needed between units. *Use a minus screwdriver: tip width 3.8 mm max., tip thickness 0.5 to 0.6 mm http://www.m-system.co.jp/ M6SXV SPECIFICATIONS ES-7982 Rev.4 Page 3/4 94 (3.70) SW1 SW1 ON OFF 1 2 3 4 5 6 7 8 MODEL: M6SXV SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM STATUS LED DIP SW Isolation 24.9Ω + Digital Output 1 5 + Computation Driver CURRENT OUTPUT (Z1) Low Drift – 2 6 – – Amplifier VOLTAGE POWER LED (S1, S2) 3 + + 7 POWER 4 – 8 CONFIGURATOR JACK POWER Specifications are subject to change without notice. http://www.m-system.co.jp/ M6SXV SPECIFICATIONS ES-7982 Rev.4 Page 4/4 CONNECTOR