MODEL: M6SXR (Usable range: -50 to +250°C, -58 to +482°F; min.span: 20°C, 36°F) Tension-Clamp Ultra-Slim Signal Conditioners M6S Series 0: Specify (Please provide a resistance table.) (Configurator software is used to change the input type and RTD TRANSMITTER range. Input code 7: Pt 1000 cannot be switched to/from (PC programmable) other input types while its temperature range can be Functions & Features changed.) • Maintenance-free tension clamp connection • 5.9-mm wide ultra-slim design [2] OUTPUT • Low profile allows the M6S module mounted in a 120-mm Current deep panel Z1: Range 0 – 20 mA DC • Accepts direct input from an RTD and provides an Voltage isolated, linearized DC signal V2: Range -10 – +10 V DC • Linearization and burnout protection V3: Range -5 – +5 V DC • PC programmable (Configurator software is used to change output over the • High-density mounting described range of the selected suffix code. • Power indicator LED For changing between suffix codes, set the Output Range • UL approval Selector on the side of unit before software adjustment.) 5.9 (.23) POWER INPUT DC Power R: 24 V DC 94 (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) (3.70) [3] OPTIONS STANDARDS & APPROVALS 102 (4.02) blank: CE marking mm (inch) /UL: UL approval (CE marking) RELATED PRODUCTS MODEL: M6SXR–[1][2]–R[3] • PC configurator software (model: M6CFG) Downloadable at M-System’s web site. A dedicated cable is required to connect the module to the ORDERING INFORMATION PC. Please refer to the internet software download site or • Code number: M6SXR-[1][2]-R[3] the users manual for the PC configurator for applicable Specify a code from below for each [1] through [3]. cable types. (e.g. M6SXR-4Z1-R/UL) • Temperature range (e.g. 0 – 100°C) • Output range (e.g. 4 – 20 mA DC) GENERAL SPECIFICATIONS Connection Input and output: Tension clamp [1] INPUT RTD Power input: Via the Installation Base (model: M6SBS) 1: JPt 100 (JIS'89) or Tension clamp (Usable range: -200 to +500°C, -328 to +932°F; min.span: 20°C, 36°F) Applicable wire size: 0.2 to 2.5 mm2, stripped length 8 mm 3: Pt 100 (JIS'89) Housing material: Flame-resistant resin (black) (Usable range: -200 to +650°C, -328 to +1202°F; min.span: 20°C, 36°F) Isolation: Input to output to power 4: Pt 100 (JIS'97, IEC) Overrange output: -2 – +102 % (Usable range: -200 to +850°C, -328 to +1562°F; min.span: 20°C, 36°F) (Negative current output is not available.) 5: Pt 50 Ω (JIS'81) Zero adjustment: -2 to +2% (PC programming) (Usable range: -200 to +649°C, -328 to +1200°F; min.span: 20°C, 36°F) Span adjustment: 98 to 102% (PC programming) 7: Pt 1000 Burnout: Upscale standard; downscale or no burnout (Usable range: -200 to +850°C, -328 to +1562°F; min.span: 20°C, 36°F) optional by programming 9: Cu 10 @25°C http://www.m-system.co.jp/ M6SXR SPECIFICATIONS ES-7980 Rev.4 Page 1/4 MODEL: M6SXR Linearization: Standard Mounting: Installation Base (model: M6SBS) or DIN rail Power LED: Green light turns on when the power is supplied. Weight: 65 g (2.3 oz) Status indicator LED: Orange LED; Flashing patterns indicate different operating status of the transmitter. PERFORMANCE in percentage of span Programming: Downloaded from PC; input type and range, Overall accuracy: Input accuracy + output accuracy output type and range, zero and span, burnout type, user’s Inversely proportional to the span. linearization table, etc. See CALCULATION EXAMPLES OF OVERALL ACURACY. For detailed information on the For detailed information, • Input accuracy: (whichever is greater) refer to the users manual for the PC configurator. ±0.1 % of input range or ±0.15°C (Pt and JPt) Configurator connection: 2.5 dia. miniature jack; ±0.1 % of input range or ±1°C (Cu 10) RS-232C level • Output accuracy: ±0.04 % of max. output range Temp. coefficient: ±0.01 %/°C (±0.006 %/°F) of max. span INPUT SPECIFICATIONS Response time: ≤ 1 sec. (0 – 90 %) INPUT: 2-, 3- or 4-wire RTD Burnout response: ≤ 10 sec. Maximum leadwire resistance: 10 Ω per wire Line voltage effect: ±0.1 % over voltage range Sensing current; ≤ 1.5 mA (≤ 0.15 mA for Pt 1000) Insulation resistance: ≥ 100 MΩ with 500 V DC If not specified, the input range is 0 – 100°C. Dielectric strength: 2000 V AC @1 minute (input to output to power to ground) OUTPUT SPECIFICATIONS • DC CURRENT CALCULATION EXAMPLES OF OVERALL ACCURACY Output range: 0 – 20 mA DC [Example] Pt 100, 0 – 100°C, Output Type -5 – +5V, Output Conformance range: 0 – 20.4 mA DC Range 1 – 5V Minimum span: 1 mA Input Accuracy** (0.15°C***) / Span (100°C) × 100 % Offset: Lower range can be any specific value within the + Max. Output Range (10V) / Span (4V) × 0.04 % output range provided that the minimum span is = ±0.25 % maintained. **Calculate the accuracy in °C. Load resistance: Output drive 11 V max. ***100°C × 0.1 % = 0.1°C ≤ 0.15°C. 0.15°C is used as input (e.g. 4 – 20 mA: 550 Ω [11 V/20 mA]) accuracy value. If not specified, the output range is 4 – 20 mA DC. • DC VOLTAGE STANDARDS & APPROVALS Code V2 (wide spans) CE conformity: Output range: -10 – +10 V DC EMC Directive (2004/108/EC) Conformance range: -10.4 – +10.4 V DC EN 61000-6-4 (EMI) Minimum span: 1 V EN 61000-6-2 (EMS) Code V3 (narrow spans) Approval: Output range: -5 – +5 V DC UL/C-UL nonincendive Class I, Division 2, Conformance range: -5.2 – +5.2 V DC Groups A, B, C, and D hazardous locations Minimum span: 0.5 V (ANSI/ISA-12.12.01, CAN/CSA-C22.2 No.213) Offset: Lower range can be any specific value within the UL/C-UL general safety requirements output range provided that the minimum span is (UL 61010-1, CAN/CSA-C22.2 No.61010-1) maintained. Load resistance: Output drive 1 mA max. (e.g. 1 – 5 V: 5000 Ω [5 V/1 mA]) If not specified, the output range is shown below. V2: 0 – 10 V DC V3: 1 – 5 V DC INSTALLATION Power consumption: Approx. 0.5 W Operating temperature: -20 to +55°C (-4 to +131°F) Operating humidity: 30 to 90 %RH (non-condensing) http://www.m-system.co.jp/ M6SXR SPECIFICATIONS ES-7980 Rev.4 Page 2/4 MODEL: M6SXR EXTERNAL VIEW � FRONT VIEW (with the cover open) � SIDE VIEW 5 6 7 8 Power LED Output Range Selectors Status Indicator LED Configurator Jack 1 2 3 4 The DIP switch setting is required to select output types before setting a precise output range using PC Configurator Software (model: M6CFG). Refer to the instruction manual for detailed procedures. DIMENSIONS unit: mm (inch) SCREWDRIVER * INSERTION ANGLE : approx. 35° WIRE INSERTION ANGLE TEST PROBE : approx.35° max. 2 (.08) dia. 5 6 7 8 DIN RAIL HOOK DIN RAIL 35mm wide 1 2 3 4 SCREWDRIVER [0.5 (.02)] INSERTION ANGLE : approx. 40° 5.9 (.23) 102 (4.02) • When mounting, no extra space is needed between units. *Use a minus screwdriver: tip width 3.8 mm max., tip thickness 0.5 to 0.6 mm http://www.m-system.co.jp/ M6SXR SPECIFICATIONS ES-7980 Rev.4 Page 3/4 94 (3.70) SW1 SW1 ON OFF 1 2 3 4 5 6 7 8 MODEL: M6SXR SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM STATUS LED 2-wire 3-wire 4-wire DIP SW Isolation RTD RTD RTD Digital Output A A A 1 5 + Computation Driver OUTPUT B A 2 6 – Low Drift POWER LED Amplifier B 3 + 7 POWER B B B 4 – 8 CONFIGURATOR JACK POWER Specifications are subject to change without notice. http://www.m-system.co.jp/ M6SXR SPECIFICATIONS ES-7980 Rev.4 Page 4/4 CONNECTOR