MODEL: M6SXF2 Tension-Clamp Ultra-Slim Signal Conditioners M6S Series [3] OUTPUT Current Z1: Range 0 – 20 mA DC 2-INPUT MATH FUNCTION MODULE Voltage (PC programmable) V2: Range -10 – +10 V DC Functions & Features V3: Range -5 – +5 V DC • Maintenance-free tension clamp connection (Configurator software is used to change the output type • 5.9-mm wide ultra-slim design and precise range.) • Low profile allows the M6S module mounted in a 120-mm deep panel • 2-input math functions and signal selector functions POWER INPUT • PC programmable DC Power • High-density mounting R: 24 V DC • Power indicator LED (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) 5.9 (.23) FUNCTIONS PC Configurator Software is used to change function type. Math Functions: Temperature compensation (w/o square root extraction) 94 (3.70) Temperature compensation (with square root extraction) Pressure compensation (w/o square root extraction) Pressure compensation (with square root extraction) Addition / Subtraction 102 (4.02) Multiplication mm (inch) Division Signal Selector Functions: High selector Low selector MODEL: M6SXF2-[1][2][3]-R RELATED PRODUCTS ORDERING INFORMATION • PC configurator software (model: M6CFG) • Code number: M6SXF2-[1][2][3]-R Downloadable at M-System’s web site. Specify a code from below for each [1] through [3]. A dedicated cable is required to connect the module to the (e.g. M6SXF2-S2Z1Z1-R) PC. Please refer to the internet software download site or • Input 1 range (e.g. 1 – 5 V DC) the users manual for the PC configurator for applicable • Input 2 range (e.g. 4 – 20 mA DC) cable types. • Output range (e.g. 4 – 20 mA DC) GENERAL SPECIFICATIONS [1] INPUT 1 Connection Current Input and output: Tension clamp Z1: Range 0 – 50 mA DC (Input resistance 24.9 Ω) Power input: Via the Installation Base (model: M6SBS) Voltage or Tension clamp S1: Range -1000 – +1000 mV DC (Input resistance 1 MΩ min.) Applicable wire size: 0.2 to 2.5 mm2, stripped length 8 mm S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.) Housing material: Flame-resistant resin (black) (Configurator software is used to change the input type and Isolation: Input 1 or input 2 to output to power precise range.) No isolation between the inputs. Maintain the same potential level at both inputs. [2] INPUT 2 Overrange output: -2 – +102 % Same range availability as Input 1 (Negative current output is not available.) (Configurator software is used to change the input type and Zero adjustment: -2 to +2% (PC programming) precise range.) Span adjustment: 98 to 102% (PC programming) http://www.m-system.co.jp/ M6SXF2 SPECIFICATIONS ES-7988 Rev.1 Page 1/5 MODEL: M6SXF2 Power LED: Green light turns on when the power is supplied. Offset: Lower range can be any specific value within the Status indicator LED: Orange LED; Flashing patterns output range provided that the minimum span is indicate different operating status of the transmitter. maintained. Programming: Downloaded from PC; input type and range, Load resistance: Output drive 1 mA max. output type and range, zero and span, function type and (e.g. 1 – 5 V: 5000 Ω [5 V/1 mA]) parameters, etc. If not specified, the output range is shown below. For detailed information, refer to the users manual for the V2: 0 – 10 V DC PC configurator. V3: 1 – 5 V DC Configurator connection: 2.5 dia. miniature jack; RS-232C level INSTALLATION Power consumption: Approx. 0.5 W INPUT SPECIFICATIONS Operating temperature: -20 to +55°C (-4 to +131°F) • DC Current: Input resistor incoporated Operating humidity: 30 to 90 %RH (non-condensing) (If not specified, the input range is 4 – 20 mA DC.) Mounting: Installation Base (model: M6SBS) or DIN rail Input range: 0 – 50 mA DC Weight: 65 g (2.3 oz) Minimum span: 2 mA Offset: Lower range can be any specific value within the PERFORMANCE in percentage of span input range provided that the minimum span is maintained. Overall accuracy: Input accuracy + output accuracy • DC Voltage See CALCULATION EXAMPLES OF OVERALL ACURACY Code S1 (narrow spans) • Input accuracy*: (% of max. input range) Input range: -1000 – +1000 mV DC -1000 – +1000 mV : ±0.05 % Minimum span: 100 mV -10 – +10 V : ±0.05 % Code S2 (wide spans) 0 – 50 mA : ±0.1 % Input range: -10 – +10 V DC • Output accuracy**: ±0.04% of max. output range Minimum span: 1 V Offset: Lower range can be any specific value within the *Inversely proportional to the span. input range provided that the minimum span is maintained. For math functions, the input accuracy equals that of either If not specified, the input range is shown below. input 1 or 2, whichever is greater, with the following S1: 0 – 100 mV DC parameter setting: S2: 1 – 5 V DC K1=K2=1, A2=0%, X2=100% for temp./press. compensation K0=0.5, K1=K2=1, A0=A1=A2=0% for four arithmetic functions OUTPUT SPECIFICATIONS For selector functions, it equals that of the selected signal. • DC CURRENT **Inversely proportional to the span. Output range: 0 – 20 mA DC Temp. coefficient: ±0.01 %/°C (±0.006 %/°F) of max. span Conformance range: 0 – 20.4 mA DC Response time: ≤ 0.5 sec. (0 – 90 %) Minimum span: 1 mA Line voltage effect: ±0.1 % over voltage range Offset: Lower range can be any specific value within the Insulation resistance: ≥ 100 MΩ with 500 V DC output range provided that the minimum span is Dielectric strength: 2000 V AC @1 minute (input to output maintained. to power to ground) Load resistance: Output drive 11 V max. (e.g. 4 – 20 mA: 550 Ω [11 V/20 mA]) CALCULATION EXAMPLES OF OVERALL ACCURACY If not specified, the output range is 4 – 20 mA DC. [Example] Function: Temperature compensation w/o square • DC VOLTAGE root extraction; K1=K2=1, A2=0%, X2=100% Code V2 (wide spans) Input 1: Type -10 – +10 V / range 1 – 5 V Output range: -10 – +10 V DC Input 2: Type 0 – 50 mA / range 4 – 20 mA Conformance range: -10.4 – +10.4 V DC Output: Type 0 – 20 mA / range 4 – 20 mA Minimum span: 1 V Input 1 = Max. Input Range (20 V) / Span (4 V) × 0.05% = Code V3 (narrow spans) 0.25% Output range: -5 – +5 V DC Input 2 = Max. Input Range (50 mA) / Span (16 mA) × 0.1% Conformance range: -5.2 – +5.2 V DC = 0.31% Minimum span: 0.5 V Output = Max. Output Range (20 mA) / Span (16 mA) × http://www.m-system.co.jp/ M6SXF2 SPECIFICATIONS ES-7988 Rev.1 Page 2/5 MODEL: M6SXF2 0.04% = 0.05% Accuracy = 0.31% (input 2 > input 1) + 0.05% = 0.36% STANDARDS & APPROVALS CE conformity: EMC Directive (2004/108/EC) EN 61000-6-4 (EMI) EN 61000-6-2 (EMS) EXTERNAL VIEW � FRONT VIEW (with the cover open) � SIDE VIEW Output Range Selectors 5 6 7 8 Power LED Status Indicator LED Configurator Jack Input Range Selectors 1 2 3 4 The DIP switch setting is required to select input and output types before setting a precise range using PC Configurator Software (model: M6CFG). Refer to the instruction manual for detailed procedures. DIMENSIONS unit: mm (inch) SCREWDRIVER * INSERTION ANGLE : approx. 35° WIRE INSERTION ANGLE TEST PROBE : approx.35° max. 2 (.08) dia. 5 6 7 8 DIN RAIL HOOK DIN RAIL 35mm wide 1 2 3 4 SCREWDRIVER [0.5 (.02)] INSERTION ANGLE : approx. 40° 5.9 (.23) 102 (4.02) • When mounting, no extra space is needed between units. *Use a minus screwdriver: tip width 3.8 mm max., tip thickness 0.5 to 0.6 mm http://www.m-system.co.jp/ M6SXF2 SPECIFICATIONS ES-7988 Rev.1 Page 3/5 94 (3.70) SW2 SW1 SW2 SW1 ON ON OFF OFF 1 2 1 2 3 4 5 6 7 8 MODEL: M6SXF2 SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM OUTPUT STATUS LED INPUT DIP SW Isolation DIP SW Digital Output + 1 5 + Computation Driver OUTPUT INPUT 1 24.9Ω 6 – – 2 Low Drift POWER LED Amplifier + + 3 7 POWER INPUT 2 24.9Ω – 8 – 4 CONFIGURATOR JACK POWER FUNCTIONS � FUNCTIONS • Math Functions Temperature compensation (w/o square root extraction) K1X1 X0 = –––––––––– √K2X2 + A2 where X0 : Compensated flow (linear characteristics) X1 : Uncompensated flow X2 : Temperature Temperature compensation (with square root extraction) K1√ X1 X0 = –––––––––– √K2X2 + A2 where X0 : Compensated flow (linear characteristics) X1 : Uncompensated flow X2 : Temperature Pressure compensation (w/o square root extraction) X0 = K1X1√K2X2 + A2 where X0 : Compensated flow (linear characteristics) X1 : Uncompensated flow X2 : Pressure Pressure compensation (with square root extraction) X0 = K1√ X1√K2X2 + A2 where X0 : Compensated flow (linear characteristics) X1 : Uncompensated flow X2 : Pressure Addition / Subtraction X0 = K0{K1(X1 + A1) + K2(X2 + A2)} + A0 Multiplication X0 = K0(K1X1 + A1) (K2X2 + A2) + A0 Division K0(K1X1 + A1) X0 = ––––––––––––––– + A0 (K2X2 + A2) • Signal Selector Functions High selector X0 = X1 with X1 ≥ X2 X0 = X2 with X1 < X2 Low selector X0 = X2 with X1 ≥ X2 X0 = X1 with X1 < X2 Available range X0 : Output (%) -2 to +102% X1 through X2 : Input (%) -2 to +102% K0 through K2 : Gain (no unit) ±29.999 A0 through A2 : Bias (%) ±299.99% Factory default setting: Addition / Subtraction K0 = 1, K1 = 1, K2 = 1, A0 = 0%, A1 = 0%, A2 = 0% http://www.m-system.co.jp/ M6SXF2 SPECIFICATIONS ES-7988 Rev.1 Page 4/5 CONNECTOR MODEL: M6SXF2 Specifications are subject to change without notice. http://www.m-system.co.jp/ M6SXF2 SPECIFICATIONS ES-7988 Rev.1 Page 5/5