MODEL: M6SVF -85 – +85 mV DC Tension-Clamp Ultra-Slim Signal Conditioners M6S Series -164 – +164 mV DC -200 – +200 mV DC SIGNAL TRANSMITTER -15 – +15 V DC (high-accuracy, ultra-high speed response 30 μsec.) -25 – +25 V DC Functions & Features -55 – +55 V DC • Maintenance-free tension clamp connection -60 – +60 V DC • 5.9-mm wide ultra-slim design • Low profile allows the M6S module mounted in a 120-mm OUTPUT deep panel Voltage • Galvanically isolates process instrumentation signals 4W: -10 – +10 V DC (Load resistance 2000 Ω min.) • 30-microsecond response • Frequency characteristics 12 kHz (-3 dB) • High-density mounting POWER INPUT • Power indicator LED DC Power R: 24 V DC Typical Applications (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) • Isolation for a vibration analyzing system • Isolation for Discharge/Charge tester GENERAL SPECIFICATIONS Connection 5.9 (.23) Input and output: Tension clamp Power input: Via the Installation Base (model: M6SBS) or Tension clamp Applicable wire size: 0.2 to 2.5 mm2, stripped length 8 mm 94 (3.70) Housing material: Flame-resistant resin (black) Isolation: Input to output to power Overrange input: -5 to +105% Zero adjustment: -1 to +1 % (front)) 102 (4.02) Span adjustment: 99 to 101 % (front) mm (inch) Power LED: Green light turns on when the power is supplied. INPUT SPECIFICATIONS MODEL: M6SVF–[1]4W–R Input resistance: 1 MΩ min. (3 kΩ min. at power loss) ORDERING INFORMATION OUTPUT SPECIFICATIONS • Code number: M6SVF-[1]4W-R Parallel load capacitance: Max. 2000 pF Specify a code from below for [1]. (e.g. M6SVF-04W-R) INSTALLATION • Special input range (For codes 0: e.g. -164 – +164 mV DC) Power consumption: Approx. 0.6 W Operating temperature: -20 to +55°C (-4 to +131°F) [1] INPUT Operating humidity: 30 to 90 %RH (non-condensing) Voltage Mounting: Installation Base (model: M6SBS) or DIN rail 2W : -100 – +100 mV DC (Input resistance 1 MΩ min.) Weight: 60 g (2.1 oz) 4W: -10 – +10 V DC (Input resistance 1 MΩ min.) 5W: -5 – +5 V DC (Input resistance 1 MΩ min.) PERFORMANCE in percentage of span 8W: -20 – +20 V DC (Input resistance 1 MΩ min.) Accuracy: ±0.01 % 0 : Specify voltage Temp. coefficient: ±0.005 %/°C (±0.003 %/°F) (Select input range as indicated below. Input resistance 1 MΩ min.) Frequency characteristics: 12 kHz, -3 dB -20 – +20 mV DC Response time: ≤ 30 µsec. (0 – 90 %) -24 – +24 mV DC Line voltage effect: ±0.01 % over voltage range -40 – +40 mV DC http://www.m-system.co.jp/ M6SVF SPECIFICATIONS ES-7994 Rev.1 Page 1/3 MODEL: M6SVF Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 2000 V AC @1 minute (input to output to power to ground) STANDARDS & APPROVALS CE conformity: EMC Directive (2004/108/EC) EN 61000-6-4 (EMI) EN 61000-6-2 (EMS) EXTERNAL VIEW (With the cover open) Power LED Zero Adj. Span Adj. DIMENSIONS unit: mm (inch) SCREWDRIVER * INSERTION ANGLE : approx. 35° WIRE INSERTION ANGLE TEST PROBE : approx.35° max. 2 (.08) dia. 5 6 7 8 DIN RAIL HOOK DIN RAIL 35mm wide 1 2 3 4 SCREWDRIVER [0.5 (.02)] INSERTION ANGLE : approx. 40° 5.9 (.23) 102 (4.02) • When mounting, no extra space is needed between units. *Use a minus screwdriver: tip width 3.8 mm max., tip thickness 0.5 to 0.6 mm http://www.m-system.co.jp/ M6SVF SPECIFICATIONS ES-7994 Rev.1 Page 2/3 94 (3.70) MODEL: M6SVF SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Z S Isolation Low Drift Output + + 1 5 SIGNAL Amplifier Driver OUTPUT SOURCE – – 2 6 POWER LED 3 + 7 POWER 4 – 8 POWER This unit, by its fast-response feature, is not designed to eliminate noise present in the input signal. Use a shielded twisted-pair cable to prevent noise from entering through the input wiring. Specifications are subject to change without notice. http://www.m-system.co.jp/ M6SVF SPECIFICATIONS ES-7994 Rev.1 Page 3/3 CONNECTOR