MODEL: M6SDY Tension-Clamp Ultra-Slim Signal Conditioners M6S Series [2] OPTIONS STANDARDS & APPROVALS blank: CE marking CURRENT LOOP SUPPLY /UL: UL approval (CE marking) Functions & Features • Maintenance-free tension clamp connection • 5.9-mm wide ultra-slim design GENERAL SPECIFICATIONS • Low profile allows the M6S module mounted in a 120-mm Connection deep panel Input and output: Tension clamp • Powers a two-wire transmitter and galvanically isolates its Power input: Via the Installation Base (model: M6SBS) output signal or Tension clamp • High-density mounting Applicable wire size: 0.2 to 2.5 mm2, stripped length 8 mm • Power indicator LED Housing material: Flame-resistant resin (black) • UL approval Isolation: Input to output to power Zero adjustment: -2 to +2 % (front) 5.9 (.23) Span adjustment: 98 to 102 % (front) Power LED: Green light turns on when the power is supplied. SUPPLY OUTPUT 94 (3.70) (across the terminals 3 – 4) Output voltage: 24 – 30 V DC with no load 18 V DC min. at 20 mA Current rating: 22 mA DC max. 102 (4.02) • Shortcircuit Protection mm (inch) Current limited: 45 mA max. Protected time duration: No limit MODEL: M6SDY–[1]–R[2] INPUT SPECIFICATIONS • DC Current: Input resistor incorporated ORDERING INFORMATION • Code number: M6SDY-[1]-R[2] INSTALLATION Specify a code from below for each [1] and [2]. Power consumption: Approx. 1 W (1.1 W for UL approval) (e.g. M6SDY-A-R/UL) Operating temperature: -20 to +55°C (-4 to +131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Installation Base (model: M6SBS) or DIN rail INPUT Weight: 60 g (2.1 oz) Current 4 – 20 mA DC (Input resistance 249.5 Ω) PERFORMANCE in percentage of span Accuracy: ±0.1 % [1] OUTPUT Temp. coefficient: ±0.01 %/°C (±0.006 %/°F) Current Response time: ≤ 100 msec. (0 – 90 %) A: 4 – 20 mA DC (Load resistance 550 Ω max.) Line voltage effect: ±0.1 % over voltage range Voltage Insulation resistance: ≥ 100 MΩ with 500 V DC 4: 0 – 10 V DC (Load resistance 10 kΩ min.) Dielectric strength: 2000 V AC @1 minute (input to output 5: 0 – 5 V DC (Load resistance 5000 Ω min.) to power to ground) 6: 1 – 5 V DC (Load resistance 5000 Ω min.) STANDARDS & APPROVALS POWER INPUT CE conformity: DC Power EMC Directive (2004/108/EC) R: 24 V DC EN 61000-6-4 (EMI) (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) http://www.m-system.co.jp/ M6SDY SPECIFICATIONS ES-7973 Rev.3 Page 1/3 MODEL: M6SDY EN 61000-6-2 (EMS) Approval: UL/C-UL nonincendive Class I, Division 2, Groups A, B, C, and D hazardous locations (ANSI/ISA-12.12.01, CAN/CSA-C22.2 No.213) UL/C-UL general safety requirements (UL 61010-1, CAN/CSA-C22.2 No.61010-1) EXTERNAL VIEW (With the cover open) Power LED Zero Adj. Span Adj. DIMENSIONS unit: mm (inch) SCREWDRIVER * INSERTION ANGLE : approx. 35° WIRE INSERTION ANGLE TEST PROBE : approx.35° max. 2 (.08) dia. 5 6 7 8 DIN RAIL HOOK DIN RAIL 35mm wide 1 2 3 4 SCREWDRIVER [0.5 (.02)] INSERTION ANGLE : approx. 40° 5.9 (.23) 102 (4.02) • When mounting, no extra space is needed between units. *Use a minus screwdriver: tip width 3.8 mm max., tip thickness 0.5 to 0.6 mm http://www.m-system.co.jp/ M6SDY SPECIFICATIONS ES-7973 Rev.3 Page 2/3 94 (3.70) MODEL: M6SDY SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM 2-WIRE TRANSMITTER Shortcircuit 24V DC + + 3 Portection Supply – – 4 Z S Isolation Low Drift Output + + 1 5 + Amplifier Driver MONITOR V OUTPUT – – 2 6 – 249.5Ω POWER LED 7 + POWER 8 – POWER � When Used as DC Supply � When Used as Isolator + + + 3 3 – – – 4 4 2-WIRE + + 1 1 TRANSMITTER INPUT – – 2 2 249.5Ω 249.5Ω Specifications are subject to change without notice. http://www.m-system.co.jp/ M6SDY SPECIFICATIONS ES-7973 Rev.3 Page 3/3 CONNECTOR