MODEL: M6DXAP N: 12 V pulse (100 kHz for FM, 1 kHz for PWM) Euro Terminal Ultra-Slim Signal Conditioners M6D Series P: 24 V pulse (100 kHz for FM, 1 kHz for PWM) Output modulation type and range are configurable with the DC/FREQUENCY CONVERTER configure software. The output signal type is configurable (PC programmable) with the DIP switches. Function & features • Converts a DC input into a FM (frequency modulation) or POWER INPUT PWM (pulse width modulated) signal DC Power • 3-port isolation R: 24 V DC • 5.9-mm wide ultra-slim design (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) • Low profile allows the M6D module mounted in a 120-mm deep panel • PC programmable [3] OPTIONS • High-density mounting blank: none • Power and status indicator LEDs /Q: With options (specify the specification) • CE marking SPECIFICATIONS OF OPTION: Q 5.9 (.23) EX-FACTORY SETTING /SET: Preset according to the Ordering Information Sheet (No. ESU-7837) 94 (3.70) RELATED PRODUCTS • PC configurator software (model: M6CFG) Downloadable at M-System’s web site. 102 A dedicated cable is required to connect the module to the (4.02) PC. Please refer to the internet software download site or mm (inch) the users manual for the PC configurator for applicable cable types. MODEL: M6DXAP–[1][2]–R[3] GENERAL SPECIFICATIONS Connection Input and output: Euro terminal (torque 0.3 N·m) ORDERING INFORMATION Power input: Via the Installation Base (model: M6DBS) • Code number: M6DXAP-[1][2]-R[3] or Euro terminal (torque 0.3 N·m) Specify a code from below each [1] through [3]. Applicable wire size: 0.2 to 2.5 mm2 (e.g. M6DXAP-Z1A-R/Q) Housing material: Flame-resistant resin (black) • Specify the specification for option code /Q Isolation: Input to output to power (e.g. /SET) Zero adjustment: -2 to +2 % (PC programming) Span adjustment: 98 to 102 % (PC programming) [1] INPUT Power LED: Green light turns on when the power is supplied. Current Status indicator LED: Orange LED; Flashing patterns Z1: Range 0 – 50 mA DC (Input resistance 25 Ω) indicate different operating status of the transmitter. Voltage Programming: Downloaded from PC S1: Range -1000 – +1000 mV DC (Input resistance 1 MΩ min.) • Input type and range S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.) • Modulation type (FM, PWM) (Configurator software is used to change the input type and • Output range precise range.) • Zero and span • User’s linearization table (max. 101 points, specified within -2 to +102 %) [2] OUTPUT • Others A: Open collector (100 kHz for FM, 1 kHz for PWM) (Refer to the instruction manual for details) M: 5 V pulse (100 kHz for FM, 1 kHz for PWM) http://www.m-system.co.jp/ M6DXAP SPECIFICATIONS ES-7837 Rev.1 Page 1/4 MODEL: M6DXAP Configurator connection: 2.5 dia. miniature jack; INSTALLATION RS-232-C level Power consumption: Approx. 1 W Operating temperature: -20 to +55°C (-4 to +131°F) Operating humidity: 30 to 90 %RH (non-condensing) INPUT SPECIFICATIONS Mounting: Installation Base (model: M6DBS) or DIN rail ■ DC Current: Input resistor incoporated Weight: 65 g (2.3 oz) (If not specified, the input range is 4 – 20 mA DC.) Input range: 0 – 50 mA DC Minimum span: 2 mA PERFORMANCE in percentage of span Offset: Lower range can be any specific value within the Accuracy: Input accuracy + output accuracy input range provided that the minimum span is maintained. Inversely proportional to the span. ■ DC Voltage Input conversion accuracy in percentage of input span: •Code S1 (narrow spans) • ±0.01 % for -1000 to +1000 mV Input range: -1000 – +1000 mV DC • ±0.01 % for -10 to +10 V Minimum span: 100 mV • ±0.02 % for 0 to 50 mA •Code S2 (wide spans) Output accuracy at max. frequency (FM): Input range: -10 – +10 V DC • ±0.10 % for ≤ 10 kHz Minimum span: 1 V • ±0.05 % for ≤ 5 kHz Offset: Lower range can be any specific value within the • ±0.02 % for ≤ 1 kHz input range provided that the minimum span is maintained. • For 10 kHz to 100 kHz output accuracy is following. If not specified, the input range is shown below. Output accuracy (%) = Max. frequency (kHz) x 0.01 S1: 0 – 100 mV DC Output accuracy (PWM): ±0.2 % S2: 1 – 5 V DC See CALCULATION EXAMPLES OF OVERALL ACCURACY. Temp. coefficient: ±0.01 %/°C (±0.006 %/°F) of max. input span OUTPUT SPECIFICATIONS Response time: 0.1 sec. + 1 pulse cycle of 100 % output ■ Modulation The time between the moment when the input changes 0 % • Frequency modulation to 100 % and the moment when the first pulse changes. Output range: 0 to 100 % Line voltage effect: ±0.1 % over voltage range Max. frequency: 100 kHz Insulation resistance: ≥ 100 MΩ with 500 V DC Min. span: 0.01 Hz Dielectric strength: 2000 V AC @1 minute (input to output (The output frequency changes according to the input to power to ground) signal. Duty rate is approx. 50 %) • Pulse width modulation Output range: 1 to 99 % CALCULATION EXAMPLES OF OVERALL ACCURACY Usable frequency: 0.008 Hz to 1 kHz 1. Frequency modulation (According to the input signal, the output pulse width (duty E.g.: Input range -10 to +10 V, input span 1 to 5 V, max. rate) changes without change of its frequency. The frequency 10 kHz frequency is configurable with PC Configurator software, Input accuracy = Input range (20 V) ÷ Input span (4 V) x M6CFG.). Input conversion accuracy (0.01 %) = 0.05 % ■ Open Collector Output accuracy = 0.10 % 50 V DC @ 100 mA (resistive load) Overall accuracy = ±0.15 % Maximum frequency: 100 kHz 2. Pulse width modulation Saturation voltage: 0.5 V DC E.g.: Input range -10 to +10 V, input span 1 to 5 V, (Factory default: 0 to 10 kHz, frequency modulation) frequency 1 kHz ■ Voltage Pulse Input accuracy = 0.05 % (same as above) High level: Rating (5, 12 or 24 V) ±10 % Output accuracy = 0.20 % Low level: ≤ 0.5 V Overall accuracy = ±0.25 % Load resistance: • ≥ 1.0 kΩ for 5 V • ≥ 2.4 kΩ for 12 V • ≥ 4.8 kΩ for 24 V Factory default: 0 to 10 kHz, Frequency modulation http://www.m-system.co.jp/ M6DXAP SPECIFICATIONS ES-7837 Rev.1 Page 2/4 MODEL: M6DXAP STANDARDS & APPROVALS CE conformity: EMC Directive (2004/108/EC) EMI EN 61000-6-4: 2007 EMS EN 61000-6-2: 2005 EXTERNAL VIEW � FRONT VIEW (with the cover open) � SIDE VIEW 5 6 7 8 Power LED Status Indicator LED Output Range Selectors Configurator Jack 1 2 3 4 The output signal type is configurable with the DIP switches. Refer to the installation manual for detailed procedure. DIMENSIONS unit: mm (inch) WIRE INSERTION ANGLE: approx. 7° 8–M3 EURO TERMINAL DIN RAIL HOOK 5 6 7 8 DIN RAIL 35mm wide 1 2 3 4 SCREWDRIVER [0.5 (.02)] INSERTION ANGLE : approx. 40° 5.9 (.23) 102 (4.02) • When mounting, no extra space is needed between units. http://www.m-system.co.jp/ M6DXAP SPECIFICATIONS ES-7837 Rev.1 Page 3/4 94 (3.70) SW1 SW1 ON OFF 1 2 3 4 5 6 7 8 MODEL: M6DXAP SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM STATUS LED DIP SW Isolation 25 Ω + Digital Output 1 5 + Computation Driver CURRENT OUTPUT (Z1) Low Drift – 2 6 – – Amplifier VOLTAGE POWER LED (S1, S2) 3 + + 7 POWER 4 – 8 CONFIGURATOR JACK POWER Output Connection Examples ع Open Collector ع Voltage Pulse 5 + + + + 5 6 – – – – 6 Specifications are subject to change without notice. http://www.m-system.co.jp/ M6DXAP SPECIFICATIONS ES-7837 Rev.1 Page 4/4 CONNECTOR