MODEL: M5PT Super-mini Terminal Block Signal Conditioners M5-UNIT [3] POWER INPUT AC Power M: 85 – 264 V AC (Operational voltage range 85 – 264 V, PT TRANSMITTER 47 – 66 Hz) Functions & Features DC Power • Converts an alternating voltage from a potential (voltage) R: 24 V DC transformer into a standard process signal (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) • True RMS sensing • High-density mounting • Power LED [4] OPTIONS 25 (.98) blank: none /Q: With options (specify the specification) 97 SPECIFICATIONS OF OPTION: Q (3.82) COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating /C02: Polyurethane coating 41 (1.61) mm (inch) /C03: Rubber coating MODEL: M5PT-[1][2]-[3][4] GENERAL SPECIFICATIONS Construction: Terminal block Connection: M3.5 screw terminals (torque 0.8 N·m) ORDERING INFORMATION Screw terminal: Nickel-plated steel Specify a code from below for each [1] through [4]. Housing material: Flame-resistant resin (black) • Code number: M5PT-[1][2]-[3][4] Isolation: Input to output to power (e.g. M5PT-14W-R/Q) Input waveform Specify variables. RMS sensing: Up to 15 % of 3rd harmonic content • Special output range (For codes Z & 0) Zero adjustment: -2 to +2 % (front) • Specify the specification for option code /Q Span adjustment: 98 to 102 % (front) (e.g. /C01 ) Power LED: Green light turns on when the power is supplied. [1] INPUT INPUT SPECIFICATIONS Voltage Frequency: 50 or 60 Hz 1: 0 – 110 V AC Input burden: 0.5 VA max. 2: 0 – 220 V AC Overload capacity: 200 % of rating for 1 min., 120 % 5: 0 – 150 V AC continuous Operational range: 5 – 120 % of rating [2] OUTPUT Current OUTPUT SPECIFICATIONS A: 4 – 20 mA DC (Load resistance 550 Ω max.) ■ DC Current: 0 – 20 mA DC Z: Specify current (See OUTPUT SPECIFICATIONS) Minimum span: 1 mA Voltage Offset: Max. 1.5 times span 4: 0 – 10 V DC (Load resistance 1000 Ω min.) Load resistance: Output drive 11 V max. 5: 0 – 5 V DC (Load resistance 500 Ω min.) ■ DC Voltage: 0 – 10 V DC 6: 1 – 5 V DC (Load resistance 500 Ω min.) Minimum span: 1 V 4W: -10 – +10 V DC (Load resistance 8000 Ω min.) Offset: Max. 1.5 times span 5W: -5 – +5 V DC (Load resistance 4000 Ω min.) Load resistance: Output drive 10 mA max.; at ≥ 1 V 0: Specify voltage (See OUTPUT SPECIFICATIONS) http://www.m-system.co.jp/ M5PT SPECIFICATIONS ES-2488 Rev.5 Page 1/3 MODEL: M5PT INSTALLATION Power Consumption •AC: Approx. 2 VA at 100 V Approx. 3 VA at 200 V Approx. 3 VA at 264 V •DC: Approx. 2 W Operating temperature: -5 to +55°C (23 to 131°F) Operating humidity: 0 to 90 %RH (non-condensing) Mounting: DIN rail Weight: 80 g (2.8 oz) PERFORMANCE in percentage of span Accuracy: ±0.3 % with input 5 – 100 % (Input 10 – 100 % for the output codes 4W and 5W) Temp. coefficient: ±0.02 %/°C (±0.01 %/°F) Response time: ≤ 0.5 sec. (0 – 90 %) Ripple: 0.5 %p-p max. Line voltage effect: ±0.1 % over voltage range Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength (input to output to power to ground) DC powered: 2000 V AC @1 minute AC powered: 1500 V AC @1 minute FRONT VIEW 1 2 Power LED 3 4 Span Adj. Zero Adj. 5 6 7 8 http://www.m-system.co.jp/ M5PT SPECIFICATIONS ES-2488 Rev.5 Page 2/3 MODEL: M5PT DIMENSIONS unit: mm (inch) 7.3 (.29) 8–M3.5 SCREW 1 2 DIN RAIL 3 4 35mm wide 5 6 7 8 25 (.98) 41 (1.61) [3.3 (.13)] • When mounting, no extra space is needed between units. SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM SOURCE Z S Isolation VT FUSE U u Resistance RMS Output + 3 5 Divider Operation Driver (V) OUTPUT V v – 4 6 (±) POWER LED 1 LOAD U(+) 7 POWER 2 V(–) 8 Specifications are subject to change without notice. http://www.m-system.co.jp/ M5PT SPECIFICATIONS ES-2488 Rev.5 Page 3/3 3 (.12) 94 (3.70) 35.4 (1.39)