MODEL: M3SXV described range of the selected suffix code. Super-space-saving Signal Conditioners For changing between suffix codes, set the Output Range M3S-UNIT Series Selector on the side of unit before software adjustment.) SIGNAL TRANSMITTER [3] POWER INPUT (PC programmable) AC Power Functions & Features M2: 100 – 240 V AC (Operational voltage range 90 – 264 V, • Converts a DC input into a standard process 47 – 66 Hz) signal DC Power • PC programmable R: 24 V DC • Universal AC/DC power input (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) • High-density mounting Universal • Power and status indicator LED AD: 100 – 240 V AC / 24 – 240 V DC (universal) • CE marking (Operational voltage range 90 - 264 V AC, 47 - 66 Hz / 21.6 - 264 V DC, ripple 10 %p-p max.) 12 (.47) RELATED PRODUCTS • PC configurator software (model: M3SCFG) 106 (4.17) Downloadable at M-System’s web site. A dedicated cable is required to connect the module to the PC. Please refer to the internet software download site or the users manual for the PC configurator for applicable 110.5 (4.35) cable types. mm (inch) GENERAL SPECIFICATIONS MODEL: M3SXV–[1][2]–[3] Construction: Small-sized front terminal structure Connection: Removable terminal block ORDERING INFORMATION Applicable wire size: 0.2 to 2.5 mm2 • Code number: M3SXV-[1][2]-[3] Housing material: Flame-resistant resin (gray) Specify a code from below for each [1] through [3]. Isolation: Input to output to power (e.g. M3SXV-Z1Z1-R) Overrange output: -2 – +102 % • Input range (e.g. 4 – 20 mA DC) (Negative current output is not available.) • Output range (e.g. 4 – 20 mA DC) Zero adjustment: -2 to +2 % (PC programming) Span adjustment: 98 to 102 % (PC programming) Power LED: Green light turns on when the power is supplied. [1] INPUT Status indicator LED: Orange LED; Flashing patterns Current indicate different operating status of the transmitter. Z1: Range 0 – 50 mA DC (Input resistance 24.9 Ω) Programming: Downloaded from PC; input type and range, Voltage output type and range, zero and span, user’s linearization S1: Range -1000 – +1000 mV DC (Input resistance 1 MΩ min.) table (max. 101 points, specified within -2 to +102% for S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.) both input and output), etc. (Configurator software is used to change the input type and For detailed information, refer to the users manual for the precise range.) PC configurator. Configurator connection: 2.5 dia. miniature jack; [2] OUTPUT RS-232-C level Current Z1: Range 0 – 20 mA DC INPUT SPECIFICATIONS Voltage • DC Current: Input resistor incoporated V2: Range -10 – +10 V DC (If not specified, the input range is 4 – 20 mA DC.) V3: Range -5 – +5 V DC Input range: 0 – 50 mA DC (Configurator software is used to change output over the http://www.m-system.co.jp/ M3SXV SPECIFICATIONS ES-7701 Rev.2 Page 1/3 MODEL: M3SXV Minimum span: 2 mA •DC: Offset: Lower range can be any specific value within the R: Approx. 0.5 W input range provided that the minimum span is maintained. AD: Approx. 1 W • DC Voltage Operating temperature: -10 to +55°C (14 to 131°F) Code S1 (narrow spans) Operating humidity: 30 to 90 %RH (non-condensing) Input range: -1000 – +1000 mV DC Mounting: DIN rail Minimum span: 100 mV Weight: 85 g (3.0 oz) Code S2 (wide spans) Input range: -10 – +10 V DC PERFORMANCE in percentage of span Minimum span: 1 V Overall accuracy: Input accuracy + output accuracy Offset: Lower range can be any specific value within the Inversely proportional to the span. input range provided that the minimum span is maintained. See CALCULATION EXAMPLES OF OVERALL ACURACY. If not specified, the input range is shown below. • Input accuracy: (% of max. input range) S1: 0 – 100 mV DC -1000 – +1000 mV : ±0.01 % S2: 1 – 5 V DC -10 – +10 V : ±0.01 % 0 – 50 mA : ±0.02 % OUTPUT SPECIFICATIONS • Output accuracy: ±0.04 % of max. output range • DC Current Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) of max. span Output range: 0 – 20 mA DC Response time: ≤ 0.5 sec. (0 – 90 %) Conformance range: 0 – 20.4 mA DC Line voltage effect: ±0.1 % over voltage range Minimum span: 1 mA Insulation resistance: ≥ 100 MΩ with 500 V DC Offset: Lower range can be any specific value within the Dielectric strength: 2000 V AC @1 minute (input to output output range provided that the minimum span is to power to ground) maintained. Load resistance: Output drive 11 V max. CALCULATION EXAMPLES OF OVERALL ACCURACY (e.g. 4 – 20 mA: 550 Ω [11 V/20 mA]) [Example] Input Type -10 – +10 V, Input Range 1 – 5 V, If not specified, the output range is 4 – 20 mA DC. Output Type -5 – +5 V, Output Range 1 – 5 V • DC VOLTAGE • Input accuracy = Max. Input Range (20 V) / Span (4 V) × Code V2 (wide spans) 0.01 % = 0.05 % Output range: -10 – +10 V DC • Output accuracy = Max. Output Range (10 V) / Span (4 V) Conformance range: -10.4 – +10.4 V DC × 0.04 % = 0.1 % Minimum span: 1 V Accuracy= ±0.15 % Code V3 (narrow spans) Output range: -5 – +5 V DC STANDARDS & APPROVALS Conformance range: -5.2 – +5.2 V DC CE conformity: Minimum span: 0.5 V EMC Directive (2004/108/EC) Offset: Lower range can be any specific value within the EMI EN 61000-6-4: 2007 output range provided that the minimum span is EMS EN 61000-6-2: 2005 maintained. Low Voltage Directive (2006/95/EC) Load resistance: Output drive 1 mA max. EN 61010-1: 2001 (e.g. 1 – 5 V: 5000 Ω [5 V/1 mA]) Installation Category II If not specified, the output range is shown below. Pollution Degree 2 V2: 0 – 10 V DC Input or output to power: Reinforced insulation (300 V) V3: 1 – 5 V DC Input to output: Basic insulation (300 V) INSTALLATION Power Consumption •AC: Approx. 2 VA at 100 V Approx. 3 VA at 200 V Approx. 4 VA at 264 V http://www.m-system.co.jp/ M3SXV SPECIFICATIONS ES-7701 Rev.2 Page 2/3 1 2 3 4 5 6 7 8 MODEL: M3SXV EXTERNAL VIEW Power LED Output Range Selectors ON OFF SW1 Status Indicator LED 1 2 Configurator Jack 3 4 EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch) 7 8 5 6 DIN RAIL 35mm wide 1 2 3 4 12 110.5 (4.35) [5 (.20)] (.47) • When mounting, no extra space is needed between units. SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM STATUS LED DIP SW Isolation 24.9Ω + Digital Output 1 5 + Computation Driver CURRENT OUTPUT (Z1) Low Drift – 2 6 – – Amplifier VOLTAGE POWER LED (S1, S2) 3 + 7 U(+) POWER 4 8 V(–) CONFIGURATOR JACK Terminal Block Specifications are subject to change without notice. http://www.m-system.co.jp/ M3SXV SPECIFICATIONS ES-7701 Rev.2 Page 3/3 106 (4.17) 62 (2.44)