Model MODEL: M2XV2 Super-mini Signal Conditioners Mini-M Series [2] OUTPUT Current Z1: Range 0 – 20 mA DC SIGNAL TRANSMITTER Voltage (PC programmable) V1: Range -2.5 – +2.5 V DC Functions & Features V2: Range -10 – +10 V DC • Converts DC input from a sensor into a standard process (Configurator software is used to change output over the signal described range of the selected suffix code. For changing • PC programmable out of this range, set the Output Range Selectors inside the • CE marking unit before software adjustment.) • UL approval Typical Applications [3] POWER INPUT • Isolation between control room and field instrumentation AC Power • Ideal for quick spare part M2: 100 – 240 V AC (Operational voltage range 85 – 264 V, 47 – 66 Hz) 23 (.91) (90 – 264 V for UL) DC Power R: 24 V DC 76 (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) (2.99) P: 110 V DC (Operational voltage range 85 – 150 V, ripple 10 %p-p max.) (110 V ±10 % for UL) 124 (4.88) mm (inch) [4] OPTIONS (multiple selections) STANDARDS & APPROVALS (must be specified) /N: Without CE or UL MODEL: M2XV2–[1][2]–[3][4] /CE: CE marking /UL: UL approval (CE marking) ORDERING INFORMATION OTHER OPTIONS • Code number: M2XV2-[1][2]-[3][4] blank: none Specify a code from below for each [1] through [4]. /Q: Option other than the above (specify the specification) (e.g. M2XV2-S2Z1-R/CE/Q) (UL not available) • Input range (e.g. 1 – 5 V DC) • Output range (e.g. 4 – 20 mA DC) SPECIFICATIONS OF OPTION: Q (multiple selections) Specify the specification for option code /Q COATING (For the detail, refer to M-System's web site.) (e.g. /C01/S01) /C01: Silicone coating /C02: Polyurethane coating [1] INPUT /C03: Rubber coating Current TERMINAL SCREW MATERIAL Z1: Range 0 – 50 mA DC (Input resistance 100 Ω) /S01: Stainless steel Voltage S1: Range -1 – +1 V DC (Input resistance 1 MΩ min.) RELATED PRODUCTS S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.) • JX configurator connection kit (model: JXCON) (Configurator software is used to change input over the described range of the selected suffix code. For changing out of this range (between S1 and S2), set the Input Range GENERAL SPECIFICATIONS Selector on the side of unit before software adjustment. Construction: Plug-in For a current input, set the Selector to the same setting as Connection: M3 screw terminals (torque 0.8 N·m) for S2 and use a receiving resistor.) Housing material: Flame-resistant resin (black) Isolation: Input to output to power Overrange output: Approx. -15 to +115 % http://www.m-system.co.jp/ M2XV2 SPECIFICATIONS ES-5081 Rev.4 Page 1/4 MODEL: M2XV2 (Negative current output is not provided.) Minimum span: 250 mV Manual zero adjustments: -5 to +5 % Code V2 (wide spans) (factory setting: 0 %) Operational range: -11.5 – +11.5 V DC Manual span adjustments: 95 to 105 % Output range: -10 – +10 V DC (factory setting: 100 %) Minimum span: 1 V Programming: Downloaded from PC; input range, output Offset: Lower range can be any specific value within the range, zero and span, simulating output, etc. output range provided that the minimum span is Status indicator LED: Flashing patterns indicate different maintained. operating status of the transmitter. Load resistance: Output drive 1 mA max. Configurator connection: 2.5 dia. miniature jack; (e.g. 1 – 5 V: 5000 Ω [5 V / 1 mA]) RS-232C level If not specified, the output range is shown below. V1: 0 – 1 V DC V2: 1 – 5 V DC INPUT SPECIFICATIONS • DC Current: Shunt resistor attached to the input terminals (0.5 W) INSTALLATION Operational range: 0 – 70 mA DC with 100 Ω, 0.5 W Power Consumption Input range: 0 – 50 mA DC •AC Power input: Minimum span: 2 mA Approx. 3 VA at 100 V Offset: Lower range can be any specific value within the Approx. 4 VA at 200 V input range provided that the minimum span is maintained. Approx. 5 VA at 264 V If not specified, the input range is 4 – 20 mA DC. •DC Power input: Approx. 2 W • DC Voltage Operating temperature: -30 to +60°C (-22 to +140°F) Code S1 (narrow spans) Operating humidity: 30 to 90 %RH (non-condensing) Operational range: -1.15 – +1.15 V DC Mounting: Surface or DIN rail Input range: -1 – +1 V DC Weight: 120 g (0.26 lbs) Minimum span: 10 mV Code S2 (wide spans) PERFORMANCE in percentage of span Operational range: -11.5 – +11.5 V DC Accuracy: Input accuracy + output accuracy Input range: -10 – +10 V DC Inversely proportional to the span. Minimum span: 100 mV Except the accuracy of input resistor. Offset: Lower range can be any specific value within the Input accuracy: (% of max. input range) input range provided that the minimum span is maintained. -1 – +1 V : ±0.01 % If not specified, the input range is shown below. -10 – +10 V : ±0.01 % S1: 0 – 100 mV DC 0 – 50 mA : ±0.02 % S2: 1 – 5 V DC Output accuracy: ±0.04 % of max. output range See CALCULATION EXAMPLES OF OVERALL ACURACY. OUTPUT SPECIFICATIONS Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) of max. span • DC Current at -5 to +55°C [23 to 131°F] Operational range: 0 – 24 mA DC Response time: ≤ 0.9 sec. (0 – 90 %) Output range: 0 – 20 mA DC Line voltage effect: ±0.1 % over voltage range Minimum span: 1 mA Insulation resistance: ≥ 100 MΩ with 500 V DC Offset: Lower range can be any specific value within the Dielectric strength: 2000 V AC @1 minute (input to output output range provided that the minimum span is to power to ground) maintained. Load resistance: Output drive 15 V max. CALCULATION EXAMPLES OF OVERALL ACCURACY (e.g. 4 – 20 mA: 750 Ω [15 V / 20 mA]) [Example] Input Type -10 – +10 V, Input Range 1 – 5 V, If not specified, the output range is 4 – 20 mA DC. Output Type 0 – 20 mA, Output Range 4 – 20 mA • DC VOLTAGE Max. Input Range (20 V) / Span (4 V) × 0.01 % = 0.05 % Code V1 (narrow spans) Max. Output Range (20 mA) / Span (16 mA) × 0.04 % Operational range: -3 – +3 V DC = 0.05 % Output range: -2.5 – +2.5 V DC Overall accuracy = 0.05 + 0.05 = ±0.10 % http://www.m-system.co.jp/ M2XV2 SPECIFICATIONS ES-5081 Rev.4 Page 2/4 MODEL: M2XV2 STANDARDS & APPROVALS CE conformity: EMC Directive (2004/108/EC) EN 61000-6-4 (EMI) EN 61000-6-2 (EMS) Low Voltage Directive (2006/95/EC) EN 61010-1 Installation Category II Pollution Degree 2 Max. operating voltage 300 V Input or output to power: Reinforced insulation Input to output: Basic insulation Approval: UL/C-UL nonincendive Class I, Division 2, Groups A, B, C, and D hazardous locations (UL 1604, CAN/CSA-C22.2 No.213) UL/C-UL general safety requirements (UL 61010B-1, CAN/CSA-C22.2 No.1010-1) EXTERNAL VIEW � FRONT VIEW (with cover open) � RIGHT SIDE VIEW Configurator Jack Input Range Selector Status Indicator LED Position L : code S1 Position H: code S2, Z1 Zero/Span Selector Top: SPAN Middle: OFF Bottom: ZERO ATT [e.g.] V UP/DOWN Switches Output code V1 SW3 I SW6 SW2 The front cover cannot be turned open by 180 deg. when there is no extra space between units. � LEFT SIDE VIEW (with cover removed) V I SW7 SW4 Output Range Selectors Refer to the instruction manual for detailed procedures. http://www.m-system.co.jp/ M2XV2 SPECIFICATIONS ES-5081 Rev.4 Page 3/4 1 O 2 N 3 4 1 O 2 N 3 4 5 6 7 8 MODEL: M2XV2 DIMENSIONS unit: mm (inch) 6 (.23) DIN RAIL 4 1 35mm wide 8 5 2–4.2x5 (.17x.20) MTG HOLE 6 (.24) deep 12 9 8–M3 SCREW 14 13 21.5 (.85) 7.3 (.29) 86.7 (3.41) 15 (.59) 116.7 (4.59) [4 (.16)] 23 (.91) • When mounting, no extra space is needed between units. TERMINAL ASSIGNMENTS unit: mm (inch) INPUT RESISTOR (model: REM2) 4 1 8 5 12 9 14 13 Input shunt resistor attached for current input. SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM STATUS INPUT RANGE ZERO/SPAN OUTPUT RANGE SELECTOR SELECTOR SELECTORS Isolation Digital Output + + 1 9 Low Drift * Computation Driver INPUT R OUTPUT Amplifier – – 4 12 UP/DOWN SWITCHES U(+) 5 13 POWER V(–) 8 14 CONFIGURATOR JACK Base Socket *Input shunt resistor attached for current input. Specifications are subject to change without notice. http://www.m-system.co.jp/ M2XV2 SPECIFICATIONS ES-5081 Rev.4 Page 4/4 70.5 (2.78) 19 (.75) 59 (2.32) 4 (.16) 72 (2.83)