Model MODEL: M2XM2 described range of the selected suffix code. For changing Super-mini Signal Conditioners Mini-M Series out of this range, set the Output Range Selectors inside the unit before software adjustment.) POTENTIOMETER TRANSMITTER (PC programmable) [2] POWER INPUT Functions & Features AC Power • Provides a DC output proportional to a potentiometer or M2: 100 – 240 V AC (Operational voltage range 85 – 264 V, slidewire position input 47 – 66 Hz) • PC programmable (90 – 264 V for UL) • Potentiometer’s zero/span points can be captured by on- DC Power site calibrations R: 24 V DC • CE marking (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) • UL approval P: 110 V DC (Operational voltage range 85 – 150 V, ripple 10 %p-p max.) Typical Applications (110 V ±10 % for UL) • Tank levels • Positions: Compensating non-linear signal from the linking mechanism of a position detector [3] OPTIONS (multiple selections) STANDARDS & APPROVALS (must be specified) 23 (.91) /N: Without CE or UL /CE: CE marking /UL: UL approval (CE marking) 76 OTHER OPTIONS (2.99) blank: none /Q: Option other than the above (specify the specification) (UL not available) 124 (4.88) mm (inch) SPECIFICATIONS OF OPTION: Q (multiple selections) COATING (For the detail, refer to M-System's web site.) MODEL: M2XM2–1[1]–[2][3] /C01: Silicone coating /C02: Polyurethane coating /C03: Rubber coating ORDERING INFORMATION TERMINAL SCREW MATERIAL • Code number: M2XM2-1[1]-[2][3] /S01: Stainless steel Specify a code from below for each [1] through [3]. (e.g. M2XM2-1Z1-R/CE/Q) • Output range (e.g. 4 – 20 mA DC) RELATED PRODUCTS • Specify the specification for option code /Q • JX configurator connection kit (model: JXCON) (e.g. /C01/S01) GENERAL SPECIFICATIONS INPUT POTENTIOMETER Construction: Plug-in 1: Total resistance 100 Ω – 10 kΩ Connection: M3 screw terminals (torque 0.8 N·m) (Configurator software is used to change input range Housing material: Flame-resistant resin (black) (total resistance).) Isolation: Input to output to power Overrange output: Approx. -15 to +115 % (Negative current output is not provided.) [1] OUTPUT Manual zero adjustments: -5 to +5 % Current (factory setting: 0 %) Z1: Range 0 – 20 mA DC Manual span adjustments: 95 to 105 % Voltage (factory setting: 100 %) V1: Range -2.5 – +2.5 V DC Programming: Downloaded from PC; linearization (100 V2: Range -10 – +10 V DC points), input range (total resistance), output range, zero (Configurator software is used to change output over the http://www.m-system.co.jp/ M2XM2 SPECIFICATIONS ES-5093 Rev.4 Page 1/4 MODEL: M2XM2 and span, simulating output, etc. Approx. 5 VA at 264 V Burnout: Upscale standard; downscale or no burnout •DC Power input: Approx. 2 W optional by programming Operating temperature: -30 to +60°C (-22 to +140°F) Status indicator LED: Flashing patterns indicate different Operating humidity: 30 to 90 %RH (non-condensing) operating status of the transmitter. Mounting: Surface or DIN rail Configurator connection: 2.5 dia. miniature jack; Weight: 120 g (0.26 lbs) RS-232C level PERFORMANCE in percentage of span INPUT SPECIFICATIONS Accuracy: Input accuracy + output accuracy • POTENTIOMETER: 100 Ω – 10 kΩ Inversely proportional to the span. Range : Minimum span Input accuracy: (% of max. input range) 0 – 100 Ω : 2.5 Ω (Range) 0 – 300 Ω : 3.0 Ω 0 – 100 Ω : ±0.02 % 0 – 1000 Ω : 10 Ω 0 – 300 Ω : ±0.02 % 0 – 10 kΩ : 10 Ω 0 – 1000 Ω : ±0.01 % Excitation: ≤ 0.5 V DC at 1000 Ω 0 – 10 kΩ : ±0.02 % Output accuracy: ±0.04 % of max. output range Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) of max. span OUTPUT SPECIFICATIONS at -5 to +55°C [23 to 131°F] • DC Current Response time: ≤ 0.9 sec. (0 – 90 %) Operational range: 0 – 24 mA DC Burnout response time: ≤ 30 sec. Output range: 0 – 20 mA DC Line voltage effect: ±0.1 % over voltage range Minimum span: 1 mA Insulation resistance: ≥ 100 MΩ with 500 V DC Offset: Lower range can be any specific value within the Dielectric strength: 2000 V AC @1 minute (input to output output range provided that the minimum span is to power to ground) maintained. Load resistance: Output drive 15 V max. (e.g. 4 – 20 mA: 750 Ω [15 V / 20 mA]) CALCULATION EXAMPLES OF OVERALL ACCURACY If not specified, the output range is 4 – 20 mA DC. [Example] Input Type 0 – 1000 Ω, Input Range 250 – 750 Ω • DC VOLTAGE ,Output Type 0 – 20 mA, Output Range 4 – 20 mA Code V1 (narrow spans) Max. Input Range (1000 Ω) / Span (500 Ω) × 0.01 % Operational range: -3 – +3 V DC = 0.02 % Output range: -2.5 – +2.5 V DC Max. Output Range (20 mA) / Span (16 mA) × 0.04 % Minimum span: 250 mV = 0.05 % Code V2 (wide spans) Overall accuracy = 0.02 % + 0.05 % = ±0.07 % Operational range: -11.5 – +11.5 V DC Output range: -10 – +10 V DC STANDARDS & APPROVALS Minimum span: 1 V CE conformity: Offset: Lower range can be any specific value within the EMC Directive (2004/108/EC) output range provided that the minimum span is EN 61000-6-4 (EMI) maintained. EN 61000-6-2 (EMS) Load resistance: Output drive 1 mA max. Low Voltage Directive (2006/95/EC) (e.g. 1 – 5 V: 5000 Ω [5 V / 1 mA]) EN 61010-1 If not specified, the output range is shown below. Installation Category II V1: 0 – 1 V DC Pollution Degree 2 V2: 1 – 5 V DC Max. operating voltage 300 V Input or output to power: Reinforced insulation INSTALLATION Input to output: Basic insulation Power Consumption Approval: •AC Power input: UL/C-UL nonincendive Class I, Division 2, Approx. 3 VA at 100 V Groups A, B, C, and D hazardous locations Approx. 4 VA at 200 V (UL 1604, CAN/CSA-C22.2 No.213) http://www.m-system.co.jp/ M2XM2 SPECIFICATIONS ES-5093 Rev.4 Page 2/4 MODEL: M2XM2 UL/C-UL general safety requirements (UL 61010B-1, CAN/CSA-C22.2 No.1010-1) EXTERNAL VIEW � FRONT VIEW (with cover open) � LEFT SIDE VIEW (with cover removed) ATT [e.g.] V Configurator Jack Output code V1 SW3 I SW6 SW2 Status Indicator LED Zero/Span Selector Top: SPAN V I Middle: OFF Bottom: ZERO SW7 SW4 UP/DOWN Switches Output Range Selectors The front cover cannot be turned open by 180 deg. when there is no extra space between units. Refer to the instruction manual for detailed procedures. DIMENSIONS unit: mm (inch) 6 (.23) DIN RAIL 4 1 35mm wide 8 5 2–4.2x5 (.17x.20) MTG HOLE 6 (.24) deep 12 9 8–M3 SCREW 14 13 21.5 (.85) 7.3 (.29) 86.7 (3.41) 15 (.59) 116.7 (4.59) [4 (.16)] 23 (.91) • When mounting, no extra space is needed between units. SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM STATUS ZERO/SPAN OUTPUT RANGE SELECTOR SELECTORS Isolation POTENTIOMETER max. Digital Output 3 + + 1 9 Computation Driver Low Drift OUTPUT 2 Amplifier UP/DOWN – 4 12 SWITCHES & Burnout 1 – U(+) 5 13 min. POWER V(–) 8 14 CONFIGURATOR JACK Base Socket http://www.m-system.co.jp/ M2XM2 SPECIFICATIONS ES-5093 Rev.4 Page 3/4 70.5 (2.78) 59 (2.32) 1 O 4 (.16) 72 (2.83) 2 N 3 4 1 O 2 N 3 4 5 6 7 8 MODEL: M2XM2 Specifications are subject to change without notice. http://www.m-system.co.jp/ M2XM2 SPECIFICATIONS ES-5093 Rev.4 Page 4/4