Model ZERO SPAN MODEL: M2SP 1: 0 – 10 mV DC (Load resistance 10 kΩ min.) Super-mini Signal Conditioners Mini-M Series 2: 0 – 100 mV DC (Load resistance 100 kΩ min.) 3: 0 – 1 V DC (Load resistance 1000 Ω min.) LOW FREQUENCY TRANSMITTER 4: 0 – 10 V DC (Load resistance 10 kΩ min.) (50 Hz minimum) 5: 0 – 5 V DC (Load resistance 5000 Ω min.) Functions & Features 6: 1 – 5 V DC (Load resistance 5000 Ω min.) • Converts the output from a pulse-type transducer 0: Specify voltage (See OUTPUT SPECIFICATIONS) into a standard process signal • CE marking [3] POWER INPUT • UL approval AC Power M: 85 – 264 V AC (Operational voltage range 85 – 264 V, Typical Applications 47 – 66 Hz) • Positive displacement flowmeters, turbine flowmeters and (Select ‘/N’ for ‘Standards & Approvals’ code.) vortex flowmeters M2: 100 – 240 V AC (Operational voltage range 85 – 264 V, • Proximity switches 47 – 66 Hz) (90 – 264 V for UL) 23 (.91) DC Power R: 24 V DC (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) 76 (2.99) R2: 11 – 27 V DC (Operational voltage range 11 – 27 V, ripple 10 %p-p max.) (Select ‘/N’ for ‘Standards & Approvals’ code.) 124 P: 110 V DC (4.88) (Operational voltage range 85 – 150 V, ripple 10 %p-p max.) mm (inch) (110 V ±10 % for UL) MODEL: M2SP-[1][2]-[3][4] [4] OPTIONS (multiple selections) LOW-END CUTOUT ORDERING INFORMATION blank: With • Code number: M2SP-[1][2]-[3][4] /DN: Without Specify a code from below for each [1] through [4]. (Select ‘/N’ for ‘Standards & Approvals’ code.) (e.g. M2SP-1A-M2/CE/Q) STANDARDS & APPROVALS (must be specified) • Input frequency range (e.g. 0 – 10 kHz) /N: Without CE or UL • Specify the specification for option code /Q /CE: CE marking (e.g. /C01/S01) /UL: UL approval (CE marking) OTHER OPTIONS blank: none [1] INPUT /Q: Option other than the above (specify the specification) 1: Dry contact (UL not available) 2: Voltage pulse SPECIFICATIONS OF OPTION: Q (multiple selections) [2] OUTPUT COATING (For the detail, refer to M-System's web site.) Current /C01: Silicone coating A: 4 – 20 mA DC (Load resistance 750 Ω max.) /C02: Polyurethane coating B: 2 – 10 mA DC (Load resistance 1500 Ω max.) /C03: Rubber coating C: 1 – 5 mA DC (Load resistance 3000 Ω max.) TERMINAL SCREW MATERIAL D: 0 – 20 mA DC (Load resistance 750 Ω max.) /S01: Stainless steel E: 0 – 16 mA DC (Load resistance 900 Ω max.) F: 0 – 10 mA DC (Load resistance 1500 Ω max.) G: 0 – 1 mA DC (Load resistance 15 kΩ max.) Z: Specify current (See OUTPUT SPECIFICATIONS) Voltage http://www.m-system.co.jp/ M2SP SPECIFICATIONS ES-5056 Rev.13 Page 1/3 MODEL: M2SP GENERAL SPECIFICATIONS PERFORMANCE in percentage of span Construction: Plug-in Accuracy: ±0.1 % (output 10 – 100 %) Connection: M3 screw terminals (torque 0.8 N·m) Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) Housing material: Flame-resistant resin (black) Response time: (0 – 90%) Isolation: Input to output to power Approx. 1.8 sec. with 0 – 50 Hz Overrange output: 0 to 120 % at 1 – 5 V Approx. 0.7 sec. with 0 – 100 Hz Zero adjustment: -5 to +5 % (front) Approx. 0.5 sec. with 0 – 500 Hz Span adjustment: 95 to 105 % (front) Approx. 0.5 sec. with 0 – 10 kHz Input pulse sensing: DC coupled; detecting pulse rise Ripple: 0.2 %p-p max. with input ≥ 10 % Input filter: Provided with input range <100 Hz Line voltage effect: ±0.1 % over voltage range (time constant approx. 1 msec.) Insulation resistance: ≥ 100 MΩ with 500 V DC Low-end cutout: 2 to 5 % Dielectric strength: 2000 V AC @1 minute (input to output (For /DN option, the output signal may fluctuate when the to power to ground) input signal is less than 5 %.) STANDARDS & APPROVALS INPUT SPECIFICATIONS CE conformity: Excitation: 12 V DC @30 mA; shortcircuit protection EMC Directive (2004/108/EC) Frequency range: 0 – 50 Hz through 10 kHz EN 61000-6-4 (EMI) • Dry Contact: Mechanical contact or open collector EN 61000-6-2 (EMS) Pulse width time requirement: 20 μsec. min. for ON and OFF Low Voltage Directive (2006/95/EC) Sensing: Approx. 12 V DC @3 mA EN 61010-1 ON/OFF level: ≤ 200 Ω for ON, ≥ 100 kΩ for OFF Installation Category II • Voltage Pulse: Square or sine waveforms Pollution Degree 2 Pulse width time requirement: 20 μsec. min. for high and Max. operating voltage 300 V low levels Input or output to power: Reinforced insulation Hi level: 2 – 50 V Input to output: Basic insulation Lo level: ≤ 1 V Approval: Input impedance: 10 kΩ min. UL/C-UL nonincendive Class I, Division 2, Groups A, B, C, and D hazardous locations (UL 1604, CAN/CSA-C22.2 No.213) OUTPUT SPECIFICATIONS UL/C-UL general safety requirements • DC Current: 0 – 20 mA DC (UL 61010B-1, CAN/CSA-C22.2 No.1010-1) Minimum span: 1 mA Offset: Max. 1.5 times span Load resistance: Output drive 15 V max. • DC Voltage: 0 – 12 V DC Minimum span: 5 mV Offset: Max. 1.5 times span Load resistance: Output drive 1 mA max.; at ≥ 0.5 V INSTALLATION Power Consumption •AC Power input: Approx. 4 VA at 100 V Approx. 5 VA at 200 V Approx. 6 VA at 264 V •DC Power input: Approx. 3 W Operating temperature: -5 to +55°C (23 to 131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Surface or DIN rail Weight: 150 g (0.33 lbs) http://www.m-system.co.jp/ M2SP SPECIFICATIONS ES-5056 Rev.13 Page 2/3 MODEL: M2SP DIMENSIONS unit: mm (inch) 6 (.23) DIN RAIL 4 1 35mm wide 8 5 2–4.2x5 (.17x.20) MTG HOLE 6 (.24) deep 12 9 8–M3 SCREW 14 13 21.5 (.85) 10 (.39) 84 (3.31) 15 (.59) 114 (4.49) [4 (.16)] 23 (.91) • When mounting, no extra space is needed between units. SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Z S Isolation Waveform Output + + 1 One-Shot Smoother 9 Shaper Driver INPUT OUTPUT – – 4 12 SENSOR EXCITATION + U(+) 5 12V Supply 13 POWER V(–) 8 14 Base Socket Input Connection Examples � Dry Contact � Voltage Pulse + 1 + 1 – – 4 4 – – +12V +12V PWR PWR + + 5 5 4kΩ Specifications are subject to change without notice. http://www.m-system.co.jp/ M2SP SPECIFICATIONS ES-5056 Rev.13 Page 3/3 70.5 (2.78) 59 (2.32) 4 (.16) 72 (2.83)