Model MODEL: M2PP Super-mini Signal Conditioners Mini-M Series [3] OUTPUT LOGIC N: The same as the input R: Inverted PULSE ISOLATOR Functions & Features • Galvanically isolates pulse rate signals [4] POWER INPUT • Input frequency = output frequency AC Power • Various outputs (relay, open collector and voltage M: 85 – 264 V AC (Operational voltage range 85 – 264 V, pulses) 47 – 66 Hz) • CE marking (Select ‘/N’ for ‘Standards & Approvals’ code.) • UL approval for 24 V DC power M2: 100 – 240 V AC (Operational voltage range 85 – 264 V, 47 – 66 Hz) Typical Applications (‘/UL’ is not selectable for ‘Standards & Approvals’ code.) • Isolating field pulse signals in order to reduce noises DC Power • Changing e.g. dry contact signal to e.g. 5 V signals R: 24 V DC (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) 23 (.91) R2: 11 – 27 V DC (Operational voltage range 11 – 27 V, ripple 10 %p-p max.) (Select ‘/N’ for ‘Standards & Approvals’ code.) 76 P: 110 V DC (2.99) (Operational voltage range 85 – 150 V, ripple 10 %p-p max.) (‘/UL’ is not selectable for ‘Standards & Approvals’ code.) 124 (4.88) [5] OPTIONS (multiple selections) mm (inch) STANDARDS & APPROVALS (must be specified) /N: Without CE or UL /CE: CE marking MODEL: M2PP–[1][2][3]–[4][5] /UL: UL approval (CE marking) OTHER OPTIONS ORDERING INFORMATION blank: none • Code number: M2PP-[1][2][3]-[4][5] /Q: Option other than the above (specify the specification) Specify a code from below for [1] through [5]. (UL not available) (e.g. M2PP-33N-M2/CE/Q) • Specify the specification for option code /Q SPECIFICATIONS OF OPTION: Q (multiple selections) (e.g. /C01/S01) COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating [1] INPUT /C02: Polyurethane coating 1: Mechanical contact (max. frequency 30 Hz) /C03: Rubber coating 2: Open collector (max. frequency 10 kHz) TERMINAL SCREW MATERIAL 3: Voltage pulse (max. frequency 10 kHz) /S01: Stainless steel [2] OUTPUT GENERAL SPECIFICATIONS 1: Low frequency open collector (max. frequency 30 Hz) Construction: Plug-in 2: High frequency open collector (max. 10 kHz) Connection: M3 screw terminals (torque 0.8 N·m) 3: 5 V pulse (max. frequency 10 kHz) Housing material: Flame-resistant resin (black) 4: 12 V pulse (max. frequency 10 kHz) Isolation: Input to output to power 5: 24 V pulse (max. frequency 10 kHz) Frequency range: Input and output are the same. 6: Mercury relay contact (max. frequency 30 Hz) Chattering protection: Filter provided for mechanical (Select ‘/N’ for ‘Standards & Approvals’ code) contact input (Not conformed to RoHS Directive) Input pulse sensing: DC coupled http://www.m-system.co.jp/ M2PP SPECIFICATIONS ES-5061 Rev.12 Page 1/4 MODEL: M2PP ≥ 5 × 107 cycles, electrical INPUT SPECIFICATIONS Excitation: 12 V DC @30 mA; shortcircuit protection • Open Collector INSTALLATION Maximum frequency: 10 kHz Power Consumption Pulse width time requirement: 10 μsec. min. for ON and OFF •AC Power input: Sensing: Approx. 12 V DC @3 mA Approx. 3 VA at 100 V ON/OFF level: ≤200 Ω for ON, ≥100 kΩ for OFF Approx. 4 VA at 200 V • Mechanical Contact Approx. 5 VA at 264 V Maximum frequency: 30 Hz •DC Power input: Approx. 3 W Pulse width time requirement: 10 msec. min. for ON and Operating temperature: -5 to +55°C (23 to 131°F) OFF Operating humidity: 30 to 90 %RH (non-condensing) Sensing: Approx. 12 V DC @3 mA Mounting: Surface or DIN rail ON/OFF level: ≤200 Ω for ON, ≥100 kΩ for OFF Weight: 150 g (0.33 lbs) • Voltage Pulse Maximum frequency: 10 kHz PERFORMANCE Pulse width time requirement: 10 μsec. min. for high and Insulation resistance: ≥ 100 MΩ with 500 V DC low levels Dielectric strength: 2000 V AC @1 minute (input to output Waveforms:Square or sine to power to ground) Hi/Lo level: 2 – 50 V for high level; ≤1 V for low level Input impedance: 10 kΩ min. STANDARDS & APPROVALS CE conformity: OUTPUT SPECIFICATIONS EMC Directive (2004/108/EC) • Low Frequency Open Collector: EN 61000-6-4 (EMI) 50 V DC @100 mA (resistive load) EN 61000-6-2 (EMS) Maximum frequency: 30 Hz Low Voltage Directive (2006/95/EC) Timer: Limits within 75 ±25 msec. EN 61010-1 ON time for output logic non-inverted Installation Category II OFF time for output logic inverted Pollution Degree 2 Saturation voltage: 0.5 V DC Max. operating voltage 300 V • High Frequency Open Collector: Input or output to power: Reinforced insulation 50 V DC @100 mA (resistive load) Input to output: Basic insulation Maximum frequency: 10 kHz Approval: Saturation voltage: 0.5 V DC UL nonincendive Class I, Division 2, • Voltage Pulse Groups A, B, C, and D hazardous locations Maximum frequency: 10 kHz (UL 1604) High level: Rating (5, 12 or 24 V) ±10 % UL general safety requirements Low level: ≤ 0.5V (UL 61010B-1) Load resistance: ≥ 250 Ω for 5 V ≥ 600 Ω for 12 V ≥ 1200 Ω for 24 V • Mercury Relay Contact Maximum frequency: 30 Hz Timer: Limits within 75 ±25 msec. ON time for output logic non-inverted OFF time for output logic inverted Rated load: 132 V AC @200 mA (cos ø = 1) 30 V DC @200 mA (resistive load) Maximum switching voltage: 350 V AC or 500 V DC Maximum switching current: 200 mA AC or 300 mA DC Maximum switching power: 26 VA or 6 W Relay life: ≥ 5 × 108 cycles, mechanical http://www.m-system.co.jp/ M2PP SPECIFICATIONS ES-5061 Rev.12 Page 2/4 MODEL: M2PP OUTPUT LOGIC VOLTAGE PULSE OPEN COLLECTOR INPUT TYPE PULSE LOGIC INPUT OUTPUT or RELAY OUTPUT H H OFF Non Inverted L L ON Voltage Pulse Input H H OFF Inverted L L ON OFF H OFF Non Inverted ON L ON Mechanical Contact Open Collector OFF H OFF Inverted ON L ON DIMENSIONS unit: mm (inch) 6 (.23) DIN RAIL 4 1 35mm wide 8 5 2–4.2x5 (.17x.20) MTG HOLE 6 (.24) deep 12 9 8–M3 SCREW 14 13 21.5 (.85) 10 (.39) 84 (3.31) 15 (.59) 114 (4.49) [4 (.16)] 23 (.91) • When mounting, no extra space is needed between units. http://www.m-system.co.jp/ M2PP SPECIFICATIONS ES-5061 Rev.12 Page 3/4 70.5 (2.78) 59 (2.32) 4 (.16) 72 (2.83) MODEL: M2PP SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Isolation * Waveform Output + 1 Timer 9 + Shaper Driver INPUT OUTPUT – 4 12 – SENSOR EXCITATION + 5 12V Supply 13 U(+) POWER 8 14 V(–) Base Socket *Low freq. open collector and mercury relay output only. Input Connection Examples Output Connection Examples � Mechanical Contact or Open Collector � Open Collector � Relay • AC Powered Relay or Counter Coil + + 1 + + 9 9 Varistor or Spark – Quenching Circuit – 4 – – LOAD 12 12 – +12V PWR + + 5 4kΩ � Voltage Pulse • DC Powered � Voltage Pulse Relay or Counter Coil + + 9 9 Spark Quenching Diode + + 1 – – LOAD 12 12 – – 4 – +12V PWR + + 5 Specifications are subject to change without notice. http://www.m-system.co.jp/ M2PP SPECIFICATIONS ES-5061 Rev.12 Page 4/4