Model MODEL: M2MNV M2: 100 – 240 V AC (Operational voltage range 85 – 264 V, Super-mini Signal Conditioners Mini-M Series 47 – 66 Hz) DC Power ANALOG SWITCHING MODULE R: 24 V DC Functions & Features (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) • Switches between two analog signal channels R2: 11 – 27 V DC • Switches/Distributes one voltage signal to two channels (Operational voltage range 11 – 27 V, ripple 10 %p-p max.) • CE marking (Select ‘/N’ for ‘Standards & Approvals’ code.) P: 110 V DC Typical Applications (Operational voltage range 85 – 150 V, ripple 10 %p-p max.) • Switching 1 – 5V DC signal: no contact failure that happens when using mechanical contacts for this purpose [4] OPTIONS (multiple selections) • Switching low-speed pulse signals Standards & Approvlas (must be specified) /N: Without CE 29.5 (1.16) /CE: CE marking Other Options blank: none 76 (2.99) /Q: Option other than the above (specify the specification) SPECIFICATIONS OF OPTION: Q (multiple selections) 124 (4.88) COATING (For the detail, refer to M-System's web site.) mm (inch) /C01: Silicone coating /C02: Polyurethane coating /C03: Rubber coating TERMINAL SCREW MATERIAL MODEL: M2MNV-[1][2]-[3][4] /S01: Stainless steel ORDERING INFORMATION GENERAL SPECIFICATIONS • Code number: M2MNV-[1][2]-[3][4] Construction: Plug-in Specify a code from below for each [1] through [4]. Connection: M3 screw terminals (torque 0.8 N·m) (e.g. M2MNV-11-M2/CE/Q) Housing material: Flame-resistant resin (black) • Specify the specification for option code /Q Switching: Photo MOS relay (e.g. /C01/S01) Isolation: Signal channel to switching command contact to Note: Must be used with its socket. NOT installable to a power multi-unit installation base. (e.g. model: M2BS-16) Power indicator LED: Green light turns on when the power is supplied. Status indicator LED 1: Green light turns on when the signal [1] SWITCHING CONTROL channel 1 (A1-B1) is alive. 1: Interlocking switching control (single-pole contact) Status indicator LED 2: Green light turns on when the signal 2: Independent switching control (double-pole contact) channel 2 (A2-B1) is alive. [2] INPUT INPUT & OUTPUT 1: Current signal (no receiving resistor) ■ Signal Channels 2: Current signal (receiving resistor 50 Ω) Max. operational voltage range: ±50 V DC (min. span 10 3: Voltage signal mV) Max. operational current range: ±50 mA DC (min. span 1 [3] POWER INPUT mA) AC Power Receiving resistor: 50 Ω incorporated (input code 2) M: 85 – 264 V AC (Operational voltage range 85 – 264 V, ON resistance: ≤ 50 Ω per wire 47 – 66 Hz) (ON resistance of photo MOS relay) (Select ‘/N’ for ‘Standards & Approvals’ code.) http://www.m-system.co.jp/ M2MNV SPECIFICATIONS ES-5095 Rev.4 Page 1/6 MODEL: M2MNV ■ Output insulation (300 V) Current signal input (no receiving resistor): Equal to the input signal Current signal input (receiving resistor 50 Ω): Voltage signal equal to [Current × 50 Ω] Voltage signal input: Equal to the input signal ■ Switching Command: Relay or open collector Contact detecting: 5 V DC / 1 mA Detecting levels: ≤ 1 kΩ at ON / ≥ 10 kΩ at OFF INSTALLATION Power Consumption •AC Power input: Approx. 3 VA at 100 V Approx. 4 VA at 200 V Approx. 5 VA at 264 V •DC power input: Approx. 2 W Operating temperature: -5 to +55°C (23 to 131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Surface or DIN rail Weight: 150 g (0.33 lbs) PERFORMANCE in percentage of span Accuracy: ±0.1 % (input code 2) Temp. coefficient: ±0.010 %/°C (±0.006 %/°F) (input code 2) Switching response time: ≤ 5 msec. Leakage current at open circuit: ≤ 1 μA Line voltage effect: ±0.1 % over voltage range Insulation resistance: ≥ 100 MΩ with 500 V DC (signal channel to switching command contact to power) Dielectric strength: 2000 V AC @1 minute (switching command contact to power to ground) 2000 V AC @1 minute (signal channel to power to ground) 1500 V AC @1 minute (signal channel to switching command contact) STANDARDS & APPROVALS CE conformity: EMC Directive (2004/108/EC) EMI EN 61000-6-4: 2007 EMS EN 61000-6-2: 2005 Low Voltage Directive (2006/95/EC) EN 61010-1: 2001 Installation Category II Pollution Degree 2 Signal channel or switching command contact to power: Reinforced insulation (300 V) Signal channel to switching command contact: Basic http://www.m-system.co.jp/ M2MNV SPECIFICATIONS ES-5095 Rev.4 Page 2/6 MODEL: M2MNV EXTERNAL VIEW • Channel 1 Status LED 1 • Channel 2 Status LED 2 Power LED DIMENSIONS unit: mm (inch) 6 (.23) DIN RAIL 3 2 1 35mm wide 6 5 4 2–4.2x5 (.17x.20) MTG HOLE 6 (.24) deep 9 8 7 11–M3 SCREW 11 10 21.5 (.85) 10 (.39) 84 (3.31) 22 (.87) 114 (4.49) [4 (.16)] 29.5 (1.16) • When mounting, no extra space is needed between units. http://www.m-system.co.jp/ M2MNV SPECIFICATIONS ES-5095 Rev.4 Page 3/6 70.5 (2.78) 59 (2.32) 4 (.16) 72 (2.83) MODEL: M2MNV SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM � INTERLOCKING SWITCHING CONTROL (single-pole contact) 2 * A1-1 1 7 B1-1 1 50Ω * A1-2 2 8 B1-2 A2-1 4 1 50Ω * A2-2 5 POWER STATUS STATUS LED LED 1 LED 2 5V 5kΩ Photo MOSFET 3 10 U(+) Relay Driver POWER SWITCHING SW1 6 11 V(–) COMMAND 9 Base Socket *1. Provided only with the input code 2: Current signal (receiving resistor 50Ω). *2. Provided only with the input code 1: Current signal (no receiving resistor). *1/*2 Not provided with the input code 3. A1-B1 channel is connected when the SW1 is turned on (closed). A2-B1 channel is connected when the SW1 is turned off (open). � INDEPENDENT SWITCHING CONTROL (double-pole contact) 2 * A1-1 1 7 B1-1 1 50Ω * A1-2 2 8 B1-2 A2-1 4 1 50Ω * A2-2 5 POWER STATUS STATUS LED LED 1 LED 2 5V 5kΩ Photo MOSFET 3 10 U(+) Relay Driver POWER 5V 11 V(–) SW1 SWITCHING 5kΩ COMMAND 6 SW2 9 Base Socket *1. Provided only with the input code 2: Current signal (receiving resistor 50Ω). *2. Provided only with the input code 1: Current signal (no receiving resistor). *1/*2 Not provided with the input code 3. A1-B1 channel is connected when the SW1 is turned on (closed). A2-B1 channel is connected when the SW2 is turned on (closed). http://www.m-system.co.jp/ M2MNV SPECIFICATIONS ES-5095 Rev.4 Page 4/6 MODEL: M2MNV SWITCHING OPERATIONS � INTERLOCKING SWITCHING CONTROL (single-pole contact) Single contact is used to switch from Signal Channel 1 (A1-B1) to Signal Channel 2 (A2-B1) and vice versa. CHANNEL 1 (A1) CHANNEL 2 (A2) Terminal 3 – 9 OFF (open) OFF ON Terminal 3 – 9 ON (closed) ON OFF Status LED turn on when the respective channels are alive. • Switching Status Current Signal (receiving resistor 50Ω) Current Signal (no receiving resistor) Voltage Signal *1 1 7 1 7 2 8 2 8 Power : OFF *1 Switching command : OFF (open) 4 4 5 5 *1 1 7 1 7 2 8 2 8 Power : ON *1 Switching command : OFF (open) 4 4 5 5 *1 1 7 1 7 2 8 2 8 Power : ON *1 Switching command : ON (short) 4 4 5 5 *1. Resistor is provided only for the input code 2: Current signal (receiving resistor 50Ω). Transition (ON to OFF, OFF to ON) Status Current Signal (receiving resistor 50Ω) Current Signal (no receiving resistor) Voltage Signal *1 1 7 1 7 2 8 2 8 Power : ON *1 Switching command : OFF to ON 4 4 or 5 5 Power : ON Switching command : ON to OFF When the switching command contact is switched from When the switching command contact is switched from OFF to ON or from ON to OFF, the signal channel is OFF to ON or from ON to OFF, the signal channel is switched only after all photo MOS relays turn on switched only after all photo MOS relays turn off (closed). (open). *1. Resistor is provided only for the input code 2: Current signal (receiving resistor 50Ω). � INDEPENDENT SWITCHING CONTROL (double-pole contact) Double contacts are used to independently switch Signal Channel 1 (A1-B1) and Signal Channel 2 (A2-B1). CHANNEL 1 (A1) CHANNEL 2 (A2) Terminal 3 – 9 OFF (open) OFF ---- Terminal 3 – 9 ON (closed) ON ---- Terminal 6 – 9 OFF (open) ---- OFF Terminal 6 – 9 ON (closed) ---- ON Status LED turn on when the respective channels are alive. http://www.m-system.co.jp/ M2MNV SPECIFICATIONS ES-5095 Rev.4 Page 5/6 MODEL: M2MNV Specifications are subject to change without notice. http://www.m-system.co.jp/ M2MNV SPECIFICATIONS ES-5095 Rev.4 Page 6/6