Model ZERO SPAN MODEL: M2DNY F: 0 – 10 mA DC (Load resistance 1500 Ω max.) Super-mini Signal Conditioners Mini-M Series G: 0 – 1 mA DC (Load resistance 15 kΩ max.) Z: Specify current (See OUTPUT SPECIFICATIONS) CURRENT LOOP SUPPLY Voltage (with square root extractor) 1: 0 – 10 mV DC (Load resistance 10 kΩ min.) Functions & Features 2: 0 – 100 mV DC (Load resistance 100 kΩ min.) • Powers a 4 – 20 mA DC current loop 3: 0 – 1 V DC (Load resistance 1000 Ω min.) • Square root extraction 4: 0 – 10 V DC (Load resistance 10 kΩ min.) • Shortcircuit protection 5: 0 – 5 V DC (Load resistance 5000 Ω min.) • Applicable to smart transmitters 6: 1 – 5 V DC (Load resistance 5000 Ω min.) • CE marking 0: Specify voltage (See OUTPUT SPECIFICATIONS) • UL approval [2] POWER INPUT Typical Applications AC Power • Various 2-wire transmitters M: 85 – 264 V AC (Operational voltage range 85 – 264 V, 47 – 66 Hz) 23 (.91) (Select ‘/N’ for ‘Standards & Approvals’ code.) M2: 100 – 240 V AC (Operational voltage range 85 – 264 V, 47 – 66 Hz) 76 (2.99) (90 – 264 V for UL) DC Power R: 24 V DC 124 (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) (4.88) R2: 11 – 27 V DC mm (inch) (Operational voltage range 11 – 27 V, ripple 10 %p-p max.) (Select ‘/N’ for ‘Standards & Approvals’ code.) MODEL: M2DNY–24[1]–[2][3] P: 110 V DC (Operational voltage range 85 – 150 V, ripple 10 %p-p max.) (110 V ±10 % for UL) ORDERING INFORMATION • Code number: M2DNY-24[1]-[2][3] Specify a code from below for each [1] through [3]. [3] OPTIONS (multiple selections) (e.g. M2DNY-24A-M2/CE/Q) STANDARDS & APPROVALS (must be specified) • Special output range (For codes Z & 0) /N: Without CE or UL • Specify the specification for option code /Q /CE: CE marking (e.g. /C01/S01) /UL: UL approval (CE marking) OTHER OPTIONS blank: none SUPPLY OUTPUT /Q: Option other than the above (specify the specification) 24: 24 V DC (UL not available) INPUT SPECIFICATIONS OF OPTION: Q (multiple selections) Current COATING (For the detail, refer to M-System's web site.) 4 – 20 mA DC /C01: Silicone coating /C02: Polyurethane coating [1] OUTPUT /C03: Rubber coating Current TERMINAL SCREW MATERIAL A: 4 – 20 mA DC (Load resistance 750 Ω max.) /S01: Stainless steel B: 2 – 10 mA DC (Load resistance 1500 Ω max.) C: 1 – 5 mA DC (Load resistance 3000 Ω max.) D: 0 – 20 mA DC (Load resistance 750 Ω max.) E: 0 – 16 mA DC (Load resistance 900 Ω max.) http://www.m-system.co.jp/ M2DNY SPECIFICATIONS ES-5066 Rev.4 Page 1/3 MODEL: M2DNY Operating humidity: 30 to 90 %RH (non-condensing) GENERAL SPECIFICATIONS Mounting: Surface or DIN rail Construction: Plug-in Weight: 150 g (0.33 lbs) Connection: M3 screw terminals (torque 0.8 N·m) Housing material: Flame-resistant resin (black) Isolation: Input to output to power PERFORMANCE in percentage of span Overrange output: 0 to 110 % at 1 – 5 V Accuracy: ±0.2 % (input 1 – 100 %) Zero adjustment: -5 to +5 % (front) Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) Span adjustment: 95 to 105 % (front) Response time: ≤ 0.5 sec. (0 – 90 %) Low-end cutout: Approx. 4 – 8 % (output) Line voltage effect Supply output: ±3 % over voltage range Output signal: ±0.1 % over voltage range Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 2000 V AC @1 minute (input to output 8% or less to power to ground) 4% or more 0 INPUT STANDARDS & APPROVALS CE conformity: EMC Directive (2004/108/EC) SUPPLY OUTPUT EN 61000-6-4 (EMI) (across the terminals 1 – 8) EN 61000-6-2 (EMS) Output voltage: 24 – 28 V DC with no load Low Voltage Directive (2006/95/EC) 18 V DC min. at 20 mA EN 61010-1 Current rating: ≤ 22 mA DC Installation Category II • Shortcircuit Protection Pollution Degree 2 Current limited: 30 mA max. Max. operating voltage 300 V Protected time duration: No limit Input or output to power: Reinforced insulation Input to output: Basic insulation INPUT SPECIFICATIONS Approval: • DC Current: Input resistors incorporated UL/C-UL nonincendive Class I, Division 2, Approx. 300 Ω (50 Ω as receiving resistor, 250 Ω across the Groups A, B, C, and D hazardous locations monitor terminals) (ANSI/ISA-12.12.01, CAN/CSA-C22.2 No.213) UL/C-UL general safety requirements (UL 61010B-1, CAN/CSA-C22.2 No.1010-1) OUTPUT SPECIFICATIONS • DC Current: 0 – 20 mA DC Minimum span: 1 mA Offset: Max. 1.5 times span Load resistance: Output drive 15 V max. • DC Voltage: 0 – 12 V DC Minimum span: 10 mV Offset: Max. 1.5 times span Load resistance: Output drive 1 mA max.; at ≥ 0.5 V INSTALLATION Power Consumption •AC Power input: Approx. 3 VA at 100 V Approx. 4 VA at 200 V Approx. 5 VA at 264 V •DC Power input: Approx. 3 W Operating temperature: -5 to +55°C (23 to 131°F) http://www.m-system.co.jp/ M2DNY SPECIFICATIONS ES-5066 Rev.4 Page 2/3 OUTPUT MODEL: M2DNY DIMENSIONS unit: mm (inch) 6 (.23) DIN RAIL 4 1 35mm wide 8 5 2–4.2x5 (.17x.20) MTG HOLE 6 (.24) deep 12 9 8–M3 SCREW 14 13 21.5 (.85) 10 (.39) 84 (3.31) 15 (.59) 114 (4.49) [4 (.16)] 23 (.91) • When mounting, no extra space is needed between units. SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Z S Isolation Sq. Root Output + 1 9 + Extractor Driver 50Ω INPUT OUTPUT – 4 12 – 2-WIRE XMTR PWR SUPPLY + 8 13 U(+) 250Ω – POWER Current 5 14 V(–) MONITOR V Limiter + 1 – 5V DC Base Socket � When Used as DC Supply � When Used as Square Root Extractor 2-WIRE TRANSMITTER – + + 1 + 1 50Ω 50Ω INPUT – 4 – 4 + + 8 8 250Ω 250Ω 5 5 Specifications are subject to change without notice. http://www.m-system.co.jp/ M2DNY SPECIFICATIONS ES-5066 Rev.4 Page 3/3 70.5 (2.78) 59 (2.32) 4 (.16) 72 (2.83)