Altitude

Designed to meet the following requirements according to Belcore GR-63, section 4.1.3:; Operating:-300 m to 4,000 m (13123 ft) (GR63 4.1.3) at aisle-ambient temperature of 40 deg C; may require additional cooling above 1800m (5905ft), Non-Operating: -300 m to 14,000 m (45931.2 ft)

Compliance/Regulatory

Designed to meet the following environmental, safety and EMC requirements: EN 300 019; Telcordia GR-63; Telcordia SR-3580 level 3; Telcordia GR-1089; Designed to meet Class B emissions limits, for a system-level goal of Class A with 6 dB margin

Dual Multicore Packet Processor Units

Dual Cavium Networks OCTEON II CN68xx MIPS64 v2 processors, each with up to 32-cores at up to 1.5 GHz depending on maximum power configuration; Interlaken lanes x 4 between the two OCTEON II processors

Electromagnetic Compatibility (EMC) and Interference (EMI)

Meets all emission and immunity requirements of FCC Part 15, GR-1089, EN 300 386, EN 55022 and EN 55024, Meets GR-1089 (3.1.2) radiated emissions requirements from 10 kHz to 10 GHz, class A, Meets GR-1089 conducted emissions requirements from 10 kHz to 30 MHz, class A, Meets all requirements of UL/CSA/EN/IEC 60950-1

Ethernet Multilayer Switch

Broadcom BCM56842 switch is connected to the Fabric Interface with configurable 40/10 GbE links [2x (4x Gb / XAUI / 4x 10G-KR / 40G-KR4)], and the Base Interface with two 1GbE links; supports up to 72 serdes ports; and each processor accesses the switch with up to 60Gbps bandwidth using two RXAUI (2x 10Gbps) and two DXAUI (2x 20Gbps) links; Supports bandwidth of 320Gbps; pin compatible upgrades available up to 480Gbps without changes to PCB layout; Supports L2 switching including QoS and static routing via Broadcom FASTPATH “Light version ”; additional protocols are available upon request including L3 routing for IPv4 and IPv6 protocols. Each group of 4 serdes is configurable to support the following options: One 40G-KR4; Four 10G-KR, One 10G-KX4 (XAUI), Four 1000Base-KX (Base-X); Supports 12x serdes lanes for up to 84 Gbps bandwidth to Rear Transition Module (RTM); standard RTM supports 84 Gbps using 8x SFP+ and 4x SFP cages

Humidity

The product meets test profile based on GR-63, EN 300 019-2-3 Class 3.1E, EN 300 019-2-2 Class 2.3 and EN 300 019-2-1, Class 1.2, Operating: 5%-93% (non-condensing) at 40°C; Non-Operating: 5%-93% (non-condensing) at 40°C

I/O Interfaces

Front: 2x RS232 - RJ45 ports, one to each OCTEON II processor, Front: 1x RS232 - RJ45 port to the switch management processor, Front: 1x 10/100/1000Base-T via RJ45 port to switch management processor

IPMI Features

Designed with IPMC, Dual IPMB, IPMI v2.0, Extensive sensor monitoring and event generation on thresholds, Two redundant IPMI firmware with rollover, Serial over LAN (IPMI v2.0) connectivity to the two CN68xx processors and the Management Processor

Mechanical Characteristics

Single slot ATCA blade

Memory

Eight (4 per processor) DDR3 DIMM sockets each supporting 32GB address range for up to 256GB for both processors once 32GB VLP DIMMs are available, Up to 1333 MHz ECC DIMM, USB Flash drive (16GB) per OCTEON II processor

Operation Power

Management TBD Wmax., TBD W typ.; Payload: TBD W max.,TBD W typ.

Rear Transition Module (RTM)

Two RTM options: RTM8242: 84 Gbps total available bandwidth; supports 8 SFP+ (FI) connectors, 4x GbE SFP (BI) connectors; RTM8940: featuring up to 2x 40G QSFP (FI), 2x 1G SFP (BI), 4x 10G SFP+ (FI) with LRM support, and optional Telco PLL (incl. optional SyncE support).

Safety

Compliant with the Low Voltage Directive, EC Council Directive 2006/95/EC; Meets electric strength requirements (5.2): Primary to Chassis 1 kV, Primary to secondary 1kV. (May be higher if maximum working voltage of converter is greater than 72 Vdc); Meets the Telcordia GR-63 material flammability requirement UL 94V-0, or V-1 with oxygen index of 28 % or greater

Shock and Vibration and Bump

Test profile based on EN 300 019-2-3, class 3.2, Shock profile: 11 ms half sine, 3 g, 3 shocks in each direction.; Meets Operational Swept Sine Vibration: test profile based on GR-63, clause 5.4.2, and ETSI EN 300 019-2-3, class 3.2., (5 to 200 Hz at 0.2 g); Meets Operational Random Vibration: test profile based on ETSI EN 300 019-2-3, class 3.2, 5 Hz to 10 Hz @ +12 dB/oct (slope up), 10 Hz to 50 Hz @ 0.02 m2/s3 (0.0002 g2/ Hz) (flat), 50 Hz to 100 Hz @ -12 dB/oct (slope down), 30 minutes per each 3 axes; Free Fall: designed to meet Bellcore GR-63, Section 5.3., Packaged -1000 mm, six surfaces, three edges and four corners, Unpackaged - 100 mm, two sides and two bottom corners

Standards Compliance

This blade is compatible to the following standards:PICMG 3.0 R3.0 specification; PICMG 3.1 R1.0 specification, IPMI v2.0, and RoHS compliant

Switch Management Processor

Single core Freescale P2010 processor, Manages the Broadcom Ethernet switch through a PCIe x1 Gen1 (2.5 Gbps) lane, One serdes lane is routed between SM processor and Broadcom switch, SM processor connected to: DDR3 ECC SODIMM; redundant NOR flash support

Telco Clock

Telco clock support provided

Temperature

Meets test profile based on GR-63, EN 300 019-2-3 Class 3.1E, EN 300 019-2-2 Class 2.3, Air Flow: TBD; Operating short term: 0°C to +55 °C; Operating long term: 0°C to +45 °C; Non-operating: -40 °C to +85 °C