HEAVY DUTY ™ SERIES SL85 NorthStar brand Bearingless Encoder Key Features • Bearingless Design Mounts to 180 C-Face Motors • Magneto-Resistive Technology Resists Dust, Dirt, Oil, Water, and Other Contaminants • Dual-C-Face Versions Available for “Sandwich” Mounting • Single or Dual Isolated Outputs Available EN 61326 SPECIFICATIONS STANDARD OPERATING CHARACTERISTICS MECHANICAL ENVIRONMENTAL Code: Incremental Max: Shaft Speed: 5,000 RPM Operating Temperature Range: -40°C to +90°C Pulses per Revolution: 64-2048 Mounting Configuration: 8.5” 180C face mount Storage Temperature Range: -40°C to +120°C Phasing Sense: A leads B for Counter-Clockwise for NEMA MG1 standards Humidity: to 98% RH (non-condensing) rotation (CCW) viewing encoder-mounted end Housing Material: Cast Aluminum Shock (Sensor Module): 1 meter drop test, Quadrature Phasing: 90° ± 22° Acceleration Rate: 3600 rpm/sec max 30 G’s Min Symmetry: 180° ± 54° Shaft Length Required: 1.0” min Vibration: 18 G’s @ 5-2000 Hz spectrum Index: 270°, ungated (optional gated to Allowable Shaft End-Play: ± 0.050” falling B edge) Allowable Shaft Runout: 0.003” TIR Number of Output Modules: Single or Dual Redundant ELECTRICAL ELECTRICAL CONNECTIONS Input Power Requirements: 5-15 Volts DC, 45 Signal Connector Pin Pigtail Cable MS 3102E18-IT# mA typical per sensor module plus line driver Common F 1 Black load Output Signals: Line Driver, 150mA source/sink B 2 Green B Frequency Response: 0 - 120kHz Data & Index A 3 A Blue Electrical Immunity: 2kV ESD, Reverse Polarity, Z * 4 Violet C Short Circuit No Connection 5 — E Connector: 10 pin industrial duty latching, sealed NEMA 4 &12, IP65 Vcc (5-15 VDC) D 6 Red — B 7 Yellow I — A 8 H Gray — Z * 9 Orange J Shield 10 Braid G * Index (Z) optional. See Ordering Information 1.46 HEAVY DUTY by SERIES SL85 Ordering Information To order, complete the model number with code numbers from the table below: Code 4: Wheel Bore Code 5: Termination Code 6: Electrical Code 7: Cover/Adapter Code 1: Model Code 2: PPR Code 3: Index 8 Ordering Information J04 5/8" bore C Latching L 5-15V in, 5-15V 0064 C Standard Flat Cover S8 Motor L No Index J05 7/8" bore Industrial Line Driver Mount E Extra heavy duty steel 0128 J06 1.00" bore Available when Connector with (4428) out Ring, for pie pan cover J07 1-1/8" bore 0256 1/2” NPT 8 1/2" Code 2 is 0512, H Same as L with F Flat Thru-hole cover K09 1-3/8" bore C-Face 0512 1024 or 2048 extended temp. to K10 1-1/2" bore M 10 pin MS Motors G Gated K11 1-5/8" bore 120°C 1024 Connector — (180C) K12 1-3/4" bore Index (Z, Z) Grounding brush kits 2048 V 5-26V in, 5-26V Single K13 1-7/8" bore Double C-face available for End of Z Differential Line Driver (IC- Output — K14 2.00" bore Sandwich Version Shaft Mounting, Index (Z, Z) WE) out K15 2-1/8" bore Consult Factory for D 1" Extended K16 2-1/4" bore 5 5-15V in, 5V Line ordering K17 2-3/8" bore height connector D8 Motor Driver (4428) out K18 2-1/2" bore Mount E 3” extended K19 2-7/8" bore Differential, Ring, for height connector Additional Shaft bidirectional signals 8 1/2" — — Sizes Available (A, A, B, B) P 18” pigtail cable C-Face Up to 3.75" Maximum Motors Q Latching End of Shaft Mounting (180C) Industrial for GE & Emerson Dual Connector on 18” Motors Output pigtail cable N01 1.125" EOS N06 2.375" EOS N08 2.625" EOS N10 2.875" EOS Note: See ACCESSORIES Section For Connectors, Spare Parts and Pulse Wheels inch [mm] DIMENSIONS STANDARD HOUSING – SINGLE C-FACE C DECODE: 2.08 P DECODE: M DECODE: LATCHING [52.9] INDUSTRIAL 18" PIGTAIL 10 PIN MS-3102 CONNECTOR CABLE CONNECTOR FOR "Q" OPTION SEE BELOW 4X 1/2-13 UNC ON 7.250 BOLT CIRCLT 7.61 [193.3] 12.21 45° [310.1] 10.65 Ş8.500 [270.6] [215.90] 8.74 8.74 [221.9] [221.9] 4.37 [110.9] 8.73 1.35 [34.3] [221.8] PLEASE REFER TO NORTHSTAR PLEASE REFER TO 2.00 [50.7] PULSE WHEEL PAGE NORTHSTAR 2.15 [54.6] ("J" SERIES WHEEL IS SHOWN) COVER PAGE "Q" OPTION 3.50 4X COUNTERBORE [88.9] FOR 1/4 SHCS 3.24 [82.3] 3.47 [88.2] 1.50 [38.1] 0.75 [19.1] 1.47 HEAVY DUTY ™ SERIES SL85 NorthStar brand inch [mm] DIMENSIONS DOUBLE C-FACE HOUSING D-DECODE: DOUBLE C-FACE INDUSTRIAL 1" EXTENDED HEIGHT LATCHING CONNECTOR 2.08 [52.9] 8.82 8.58 [218.1] [224.0] 5.35 12.95 [135.8] [328.9] 4.37 [111.0] 8.500 [215.90] 4.37 [111.0] 1/2-13 UNC ON 45° 0.19 [4.8] 1.10 [27.9] 7.25 BOLT CIRCLE PLEASE REFER TO NORTHSTAR COVER PAGE PLEASE REFER TO 1.90 [48.3] NORTHSTAR PULSE WHEEL PAGE ("J" SERIES WHEEL IS SHOWN) P-DECODE: E-DECODE: DOUBLE C-FACE DOUBLE C-FACE 18" PIGTAIL 3" EXTENDED HEIGHT SEE "Q" INDUSTRIAL OPTION BELOW LATCHING CONNECTOR "Q" OPTION 3.50 [88.9] 3.47 [88.2] 3.24 [82.3] 14.98 [380.4] 1.50 4X COUNTERBORE FOR 1/4 SHCS [38.1] 0.75 [19.1] 8.74 [221.9] 1.48 HEAVY DUTY by SERIES SL85 inch [mm] DUAL OUTPUT HOUSING DIMENSIONS 4.37 4.37 [111.0] [111.0] PLEASE REFER TO NORTHSTAR PULSE WHEEL PAGE ("J" SERIES WHEEL IS SHOWN) 4.37 [111.0] 2.08 [52.9] 2.08 [52.9] 4.36 45° E DECODE: [110.9] DOUBLE C-FACE 1/3-13 UNC ON 3" EXTENDED HEIGHT Ş7.25 BOLT CIRCLE INDUSTRIAL PLEASE REFER TO NORTHSTAR LATCHING CONNECTOR COVER PAGE 10.61 10.61 [269.5] [269.5] 0.19 [4.8] 2.10 [53.3] 1.10 [27.9] 8.58 8.58 D DECODE: [218.1] [218.1] DOUBLE C-FACE 1" EXTENDED HEIGHT INDUSTRIAL LATCHING CONNECTOR 4.37 4.37 P DECODE: [111.0] [111.0] DOUBLE C-FACE 18" PIGTAIL SEE "Q" OPTION AT RIGHT "Q" OPTION 3.50 4X COUNTERBORE [88.9] FOR 1/4 SHCS 1.50 [38.1] 3.47 [88.2] 0.75 [19.1] 1.49