For more detailed documentation, visit us online at www.adtran.com ATLAS 830 P/N 1200780L1 (AC)/1200781L1 (DC) Quick Start Guide Network Ports LEDs Option Module LEDs Reviewing the Front Panel Controller LEDs NETW ORK 1 2 MODULES ATLAS 830 POWER OK OK 1 2 3 4 5 6 7 8 STATUS SYSTEM TEST TEST ACO CRAFT ONLINE ETHERNET ERROR ERROR REMOTE ALARM ALARM TEST ACO Switch Craft Interface Craft Pinout Connecting to the ATLAS 830 PIN NAME DESCRIPTION Connecting a VT100 terminal (or VT100 terminal emulator) to the CRAFT 1, 4, 6-9 N/A Not Connected interface (on the front panel of the unit) or the ADMIN interface (on the rear panel 2 RD Receive Data (output) of the unit) allows access to the terminal menus and management features of the ATLAS 830. 3 TD Transmit Data (input) 5 SG Signal Ground Perform Steps Below in the Order Listed: System Status LEDs 1. Configure a VT100 terminal (or terminal emulation software) with the The System Status LEDs display the status of the power supply, controller, and following settings: other system parameters for the ATLAS 830. For a more detailed discussion of the front panel LEDs, refer to Section 2, Engineering Guidelines, of the ATLAS Data Rate: 9600 baud Stop Bits: 1 830 System Manual. Data Bits: 8 Flow Control: None Parity Bits: None LED Description Power Indicates the status of the power supply If the terminal has a parallel setting, disable it and use serial. System Indicates the status of the unit controller and other system parameters. Ethernet Indicates the status of the ethernet port. 2. Connect the DB-9 male end of the data cable into the ATLAS 830 CRAFT or ADMIN port. Make the connection to the VT100 terminal as appropriate for Remote Indicates whether a user (Telnet or VT100) is logged in to the unit. your connection. 3. Initiate a terminal session and the LOGIN screen displays. The default password is password. (Passwords in the ATLAS 830 are case sensitive.) Quick Start Guide, 61200780L1-13A, August 2002 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright  2002 ADTRAN, All Rights Reserved For more detailed documentation, visit us online at www.adtran.com ATLAS 830 P/N 1200780L1 (AC)/1200781L1 (DC) Quick Start Guide Optional DC Reviewing the Rear Panel Design Network T1/PRI Ports T1/PRI Monitor Jacks Power Supply Alarm Relay Connection P/N 1200229L1 CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE AND RATING OF FUSE. Admin Interface ON OFF 12A/125V - + 48 VDC, 6A USE COPPER CONDUCTORS ONLY SEE MANUAL BEFORE REMOVING POWER SUPPLY Power Supply Slot Option Module Slots Alarm Relay Connection Pinout Admin Pinout PIN NAME DESCRIPTION PIN NAME DESCRIPTION 1 Normaly Closed (NC) Opens when a selected alarm condition is present. 1 DCD Data Carrier Detect (output) 2 Normally Open (NO) Closes when a selected alarm condition is present. 2 RD Receive Data (output) 3 Common (COM) Common connection between external circuitry 3 TD Transmit Data (input) and NC or NO terminal. 4 DTR Data Terminal Ready (input) 4 Chassis Ground (GND) 5 SG Signal Ground 6 DSR Data Set Ready (output) -- not connected 7 RTS Request to Send (input) DC Power Supply Connection 8 CTS Clear to Send (output) (Optional P/N 1200229L1) 9 RI Ring Indicate (output) -- not connected PIN NAME DESCRIPTION 1 + Ground (GND) 10/100BaseT Ethernet Pinout 2- -48VDC PIN NAME DESCRIPTION 1 TX1 Transmit Positive 2 TX2 Transmit Negative 3 RX1 Receive Positive 4,5 — Unused 6 RX2 Receive Negative 7, 8 — Unused Quick Start Guide, 61200780L1-13A, August 2002 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright  2002 ADTRAN, All Rights Reserved