110 WATT SWITCHING POWER SUPPLIES PROTEK DESCRIPTION PUP110 SERIES The PUP110 series of AC/DC switching power supplies RoHS are for 110 watts of continuous output power. They are enclosed in a 94V-1 rated polyphenylene-oxide case with an IEC 320 inlet to mate with interchangeable cord for world-wide use. An on/off switch can be added at request. All models meet CISPR 22 and FCC class B emission limits, and comply with UL, CSA, IEC and CE requirements. FEATURES Safety Standard Approvals： ‧ Single, dual, triple or quadruple outputs ‧ Optional output connectors UL 60950-1, CSA C22.2 NO. 60950-1 ‧ Optional on/off switch File No. E137410 ‧ Optional Power Fail Detect (PFD) signal ‧ 100﹪ burn-in TÜV EN60950-1 ‧ Wide input range 85 to 264VAC Certificate No. S9452794 ‧ Input surge current protection ‧ Overvoltage protection ‧ Overcurrent protection ‧ Compliant with RoHS requirements ENVIRONMENTAL SPECIFICATIONS Operating temperature： 0℃ to +70℃ Storage temperature： -40℃to +85℃ Relative humidity： 5﹪ to 95﹪ non-condensing INPUT SPECIFICATIONS Derating： Derate from 100﹪ at +50℃ Input voltage： 85 to 264VAC linearly to 50﹪ at +70℃ Input frequency： 47 to 63Hz Input current： 3.20A（ rms） for 115VAC 1.80A（ rms） for 230VAC GENERAL SPECIFICATIONS Earth leakage current: 0.40mA max. @ 115VAC, 60Hz Switching frequency： 20KHz to 250KHz, varies with load (Touch current) 0.80mA max. @ 230VAC, 50Hz and line Efficiency： 70﹪minimum on single output models with Vo ≥ 12V, 65% minimum on the others Hold-up time： 12 msec minimum at 110VAC Line regulation： ±0.5﹪maximum at full load OUTPUT SPECIFICATIONS Inrush current： 15 amps @ 115VAC or 30 amps Output voltage/current： See rating chart @ 30VAC, at 25℃ cold start 110 watts maximum Total output power： Withstand voltage： 3000VAC from input to output Ripple and noise： 1﹪peak to peak maximum 1500VAC from input to ground Overvoltage protection： Provided on output #1 only; set 500VAC from output to ground at 112-132﹪of its nominal MTBF： 550,000 hours minimum at full load output voltage at 25℃ ambient, calculated per Overcurrent protection： All outputs protected to short circuit conditions MIL-HDBK-217F, excluding DC fan EMC Performance (EN55024) Temperature coefficient： All outputs ±0.04﹪/℃ maximum EN55022: Class B conducted, Class B radiated Transient response： Maximum excursion of 4﹪or FCC: Class B conducted, Class B radiated better on all models, recovering VCCI: Class B conducted, Class B radiated to 1﹪of final value within EN61000-3-2: Harmonic distortion, Class A 500us after a 25﹪step load EN61000-3-3: Line flicker change EN61000-4-2: ESD, ± 8KV air and ± 4KV contact PFD signal (optional)： TTL logic high for normal EN61000-4-3: Radiated immunity, 3V/m operation and TTL logic low upon loss of input power. This EN61000-4-4: Fast transient/burst, ± 1KV signal appears at least 1ms EN61000-4-5: Surge, ± 1KV diff., ± 2KV com. prior to +5V output dropping EN61000-4-6: Conducted immunity, 3Vrms 5% below its nominal value. EN61000-4-8: Magnetic field immunity, 1A/m This signal also provides a minimum delay of 100ms after EN61000-4-11: Voltage dips, 30﹪reduction for +5V is within regulation. 500ms and >95﹪reduction for 10ms 3-9 UNIVERSAL INPUT PUP110 SERIES OUTPUT VOLTAGE/CURRENT RATING CHART Maximum Output #1 Output #2 (1) Output #3 Output #4 Output MODEL (2) Vnom. Imin. Imax. Tol. Vnom. Imin. Imax. Ipeak. Tol. Vnom. Imin. Imax. Tol. Vnom. Imin. Imax. Tol. Power PUP110-10 5V 0A 22A 5% (N/A) (N/A) (N/A) 110W PUP110-12 12V 0A 9.0A 4% (N/A) (N/A) (N/A) 110W PUP110-13 15V 0A 7.5A 3% (N/A) (N/A) (N/A) 110W PUP110-14 24V 0A 4.5A 3% (N/A) (N/A) (N/A) 110W PUP110-16 30V 0A 3.6A 3% (N/A) (N/A) (N/A) 110W PUP110-18 48V 0A 2.3A 3% (N/A) (N/A) (N/A) 110W PUP110-23 +5V 0A 10A 5% +12V 0A 5A 9.0A5% (N/A) (N/A) 110W PUP110-31 +5V 0A 10A 5% +12V 0A 5A 9.0A5% -12V 0A 1A5% (N/A) 110W PUP110-32 +5V 0A 10A 5% +15V 0A 4A 7.5A5% -15V 0A 1A5% (N/A) 110W PUP110-40 +5V 0A 10A 5% +12V 0A 5A 9.0A 5% -12V 0A 1A 5% -5V 0A 1A 5% 110W PUP110-41 +5V 0A 10A 5% +15V 0A 4A7.5A5% -15V 0A 1A5%+24V 0A 1A 5% 110W PUP110-42 +5V 0A 10A 5% +12V 0A 5A9.0A5% -12V 0A 1A5%+12V 0A 1A 5% 110W PUP110-45 +5V 0A 10A 5% +12V 0A 5A9.0A5% -12V 0A 1A5%+24V 0A 1A 5% 110W PUP110-45-1 +5V 2A 10A 5% +12V 0A 5A 9.0A5% -12V 0A 1A5%+24V 1.5A 3A 10% 110W PUP110-45-2 +5V 0A 10A 5% +24V 0A 3A 5.0A5% -12V 0A 1A5%+12V 0A 1A 5% 110W PUP110-46 +5V 0A 10A 5% +15V 0A 4A7.5A5% -15V 0A 1A5% -5V 0A 1A 5% 110W NOTES: 1. Peak output current with 10% maximum duty cycle for less than 60 seconds. Total peak power must not exceed 130 watt 2. The output #1 of model PUP110-45-1 needs a minimum current of 2A to support the other output at their maximum rated load MECHANICAL SPECIFICATIONS NOTES: 1. Dimensions shown in inch [mm] 2. Tolerance 0.02 [0.5] maximum 3. Weight: 1.40 kgs (3.08 Lbs.) approx. 4. See pages 6-1 to 6-26 for optional output connectors. Add the suffix assigned for a selected connector to a wanted model number, e.g. PUP110-31-K1, for ordering. 5. To order a model with on/off switch, add suffix “S” to the model number, e.g. PUP110-31-K1-S. 6. To order a model with PFD signal, add suffix “PF” to the model number, e.g. PUP110-31-K1-PF. PIN CHART PIN 1 2 3 4 5 6 7 8 MODEL PUP110-10 PUP110-12 OUTPUT OUTPUT OUTPUT N.C. or PUP110-13 PUP110-14 RETURN RETURN RETURN RETURN #1 #1 #1 PFD PUP110-16 PUP110-18 COMMON OUTPUT OUTPUT COMMON OUTPUT N.C. or PUP110-23 N.C. N.C. RETURN #1 #2 RETURN #1 PFD COMMON OUTPUT OUTPUT OUTPUT COMMON OUTPUT N.C. or PUP110-31 PUP110-32 N.C. RETURN #3 #1 #2 RETURN #1 PFD PUP110-40 PUP110-41 PUP110-42 PUP110-45 COMMON OUTPUT OUTPUT OUTPUT OUTPUT COMMON OUTPUT N.C. or PUP110-45-1 PUP110-45-2 RETURN #3 #1 #4 #2 RETURN #1 PFD PUP110-46 3-10