IFC125-42-3 - XP POWER - Industrial Trading

Description

XP Power IFC125-42-3 125 Watts Small Size Power Supply | 3.0" x 5.0" x 1.25" | Quad Outputs | V1: 3.3V/10A | V2: 5V/15A | V3: 12V/5A | V4: -12V/0.5A | Active PFC

Part Number

IFC125-42-3

Price

Request Quote

Manufacturer

XP POWER

Lead Time

Request Quote

Category

Power Supply

Specifications

Conducted Immunity

EN61000-4-6

Cooling

5 CFM airflow required for 125 W

Current Share

Up to 4 supplies to share within 10%

Dips & Interruptions

EN61000-4-11, 30% 10 ms, 60% 100 ms, 100% 5000 ms, Criteria A, B, B

Earth Leakage Current

0.5 mA max at 132 VAC/60Hz; 0.825 mA max at 264 VAC/50Hz

Efficiency

83% typical

EFT/Burst

EN61000-4-4, level 3 Perf Criteria B

Emissions

EN55022/CISPR22 and FCC, Class B conducted

Harmonic Currents

EN61000-3-2

Hold Up Time

>28 ms min at full load

Initial Set Accuracy

±5% maximum

Input Current

0.8 A max at 240 VAC; 1.8 A max at 100 VAC

Input Frequency

47-63 Hz

Input Protection

Internal 2.6 A fuse

Input Voltage

90-264 VAC

Inrush Current

33 A max at 115 VAC; 66 A max at 230 VAC

Isolation

3000 VAC Input to Output; 1500 VAC Input to Ground; 500 VAC Output to Ground

Minimum Load

5 W minimum load on V1 or V2 required to maintain regulation

MTBF

>220 kHrs per Bellcore

Operating Altitude

3000 m

Operating Humidity

5-95% RH, non-condensing

Operating Temperature

-25 °C to +70 °C, derate linearly from 100% at +50 °C to 50% at +70 °C

Output Voltage Trim

Not user-adjustable

Over/Undershoot

10% maximum

Overload Protection

All outputs: 115-135%, auto recovery

Overtemperature Protection

Unit shuts down, recycle input to reset

Overvoltage Protection

V1 & V2: 113-148%, auto recovery

Power Density

6.66 W/In3

Power Factor

0.98 typical

Radiated Immunity

EN61000-4-3, level 3 Perf Criteria B

Remote Sense

V1 only compensates for 0.5 V drop

Ripple & Noise

±1% pk-pk maximum or =5 Vout 50 mV maximum

Safety Approvals

EN60950, UL 60950, CSA950 per cUL, CE Mark LVD

Shock

15 G pk operating

Short Circuit Protection

Trip and restart (Hiccup mode)

Signals

Power Good - On is Logic High

Start Up Delay

1.5 s at 90 VAC

Start Up Rise Time

0.2-20 ms

Storage Temperature

-40 °C to +85 °C

Surge

EN61000-4-5, level 3 Perf Criteria B

Temperature Coefficient

0.04% / °C maximum

Transient Response

5% max. deviation, recovery to within 1% in 500 µs for a 25% load change

Vibration

2.4 G, 5 Hz to 500 Hz, 3 axis

Voltage Flicker

EN61000-3-3

Features

-25 °C to +50 °C Full Power
Active PFC - Meets EN61000-3-2, -3
Current Share up to 4 Units
Overvoltage & Overcurrent Protection
Power Good Signal
Single, Triple and Quad Outputs
Small Size - 3.0” x 5.0” x 1.25”

Datasheet

IFC125-42-3.pdf

207 KiB

Download

Extracted Text

125 Watts xppower.com IFC125 Series • Small Size - 3.0” x 5.0” x 1.25” • Single, Triple and Quad Outputs • Active PFC - Meets EN61000-3-2, -3 • Current Share up to 4 Units • Overvoltage & Overcurrent Protection • Power Good Signal • -25 ˚C to +50 ˚C Full Power Specification Input General Input Voltage • 90-264 VAC Efficiency • 83% typical Input Frequency • 47-63 Hz Isolation • 3000 VAC Input to Output 1500 VAC Input to Ground Input Current • 0.8 A max at 240 VAC 500 VAC Output to Ground 1.8 A max at 100 VAC 3 Power Density • 6.66 W/In Inrush Current • 33 A max at 115 VAC 66 A max at 230 VAC Signals • Power Good - On = Logic High Power Factor • 0.98 typical MTBF • >220 kHrs per Bellcore Earth Leakage Current • 0.5 mA max at 132 VAC/60Hz 0.825 mA max at 264 VAC/50Hz Environmental Input Protection • Internal 2.6 A fuse Operating Temperature • -25 ˚C to +70 ˚C, derate linearly from 100% at +50 ˚C to 50% at +70 ˚C Output Cooling • 5 CFM airflow required for 125 W Output Voltage • See table Operating Humidity • 5-95% RH, non-condensing Output Voltage Trim • Not user-adjustable Storage Temperature • -40 ˚C to +85 ˚C Initial Set Accuracy • ±5% maximum Operating Altitude • 3000 m Minimum Load • 5 W minimum load on V1 or V2 required Shock • 15 G pk operating to maintain regulation Vibration • 2.4 G, 5 Hz to 500 Hz, 3 axis Start Up Delay • 1.5 s at 90 VAC Start Up Rise Time • 0.2-20 ms EMC & Safety Hold Up Time • >28 ms min at full load Emissions • EN55022/CISPR22 and FCC, Class Line Regulation • See table B conducted Load Regulation • See table Harmonic Currents • EN61000-3-2 Over/Undershoot • 10% maximum Voltage Flicker • EN61000-3-3 Transient Response • 5% max. deviation, recovery to within Radiated Immunity • EN61000-4-3, level 3 Perf Criteria B 1% in 500 µs for a 25% load change EFT/Burst • EN61000-4-4, level 3 Perf Criteria B Ripple & Noise • ±1% pk-pk maximum or ≤5 Vout 50 mV Surge • EN61000-4-5, level 3 Perf Criteria B maximum Conducted Immunity • EN61000-4-6 Overvoltage Protection • V1 & V2: 113-148%, auto recovery Dips & Interruptions • EN61000-4-11, 30% 10 ms, 60% 100 ms, Overtemperature • Unit shuts down, recycle input to reset 100% 5000 ms, Criteria A, B, B Protection Safety Approvals • EN60950, UL 60950, CSA950 per cUL, Overload Protection • All outputs: 115-135%, auto recovery CE Mark LVD Short Circuit Protection • Trip and restart (Hiccup mode) Temperature • 0.04% / ˚C maximum Coefficient Remote Sense • V1 only compensates for 0.5 V drop (not available on IFC125-31) Current Share • Up to 4 supplies to share within 10% 1 AC-DC AC-DC IFC125 Models and Ratings Output 1 Output 2 Output 3 Output 4 Model (1) (1) (1) (1) Vnom Imax Vnom Imax Vnom Imax Vnom Imax Number Reg Reg Reg Reg 24.0 V 5.2 A ±3% 12.0 V 0.5 A ±5% IFC125-14 5.0 V 16.5 A ±4% 12.0 V 5.0 A ±5% -12.0 V 0.5 A ±5% IFC125-31 2.5 V 12.5 A ±2% 5.0 V 15.0 A ±4% 12.0 V 5.0 A ±5% -12.0 V 0.5 A ±5% IFC125-40-1 3.3 V 10.0 A ±2% 5.0 V 15.0 A ±4% 12.0 V 5.0 A ±5% -12.0 V 0.5 A ±5% IFC125-42-3 Notes 1. Total regulation includes tolerance, line regulation and load regulation. 2. Maximum output power not to exceed 125W with 5 CFM forced air or 70W with convection cooling. 3. For IFC125-40-1 and -42-3, a maximum of 80W combined +2.5V or +3.3V and +5V outputs with 5CFM of forced air cooling or 40W with convection cooling. 4. 5W minimum load required to maintain regulation. Mechanical Details Connector Pin-outs IFC125-31 IFC125-40-1 IFC125-42-3 Conn Pin 1 Neutral Neutral Neutral J1 2 3 Line Line Line 1 -12 VDC -12 VDC -12 VDC 2 +12 VDC +12 VDC +12 VDC 3 Not Used +2.5 VDC +3.3 VDC 5.00 4 Not Used +2.5 VDC +3.3 VDC (127.0) 5 Not Used +2.5 VDC +3.3 VDC 4.55 6 DC GND DC GND DC GND 0.23 (5.7) (115.6) 7 DC GND DC GND DC GND Ø 0.16 (4.1) J2 8 DC GND DC GND DC GND (4 places) 9 DC GND DC GND DC GND 10 DC GND DC GND DC GND 11 +5 VDC +5 VDC +5 VDC 12 +5 VDC +5 VDC +5 VDC 13 +5 VDC +5 VDC +5 VDC 14 +5 VDC +5 VDC +5 VDC 3.00 3.00 J2 - DC output 1 0 V Sense 0 V Sense 0 V Sense (76.2) (76.2) 2.55 connector for J3 2 Not Used +2.5 V Sense +3.3 V Sense (64.8) IFC125-31, -40-1, Pin #1 3 Power Good Power Good Power Good 42-3. (see pin-out table) J1 - Input connector Safety ground Pin #1 Pin #1 connection point Fastener clearance area (4 places) J3 - Remote Sense/ PG connector Lock washer Screws shown for reference only 1.00 0.06 0.19 1.25 (25.4) (1.5) (4.8) (31.8) PCB Molex Mating Connectors IFC125-31 & -40-1 IFC125-42-3 Housing 09-50-8031 90-50-8033 J1 Pins 08-52-0113 08-52-0113 Notes Housing 09-50-8141 09-50-8143 1. All dimensions in inches (mm). J2 2. Weight 0.68 lb (310 g) approx (-14 models 0.6 lb, 270g). Pins 08-52-0113 08-52-0113 Housing 22-01-3037 22-01-3037 J3 Pins 08-50-0114 08-50-0114 16-Aug-05

Frequently asked questions

Industrial Trading' parent company, GID Industrial, specializes in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

The warranty we offer will be based on what we negotiate with our suppliers. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

We use FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Industrial Trading will definitely serve you. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

Visa, MasterCard, Discover, and American Express are all accepted by Industrial Trading. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

What they say about us

FANTASTIC RESOURCE

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Why buy from GID?

What they say about us

Related Products