Manufacturers
XP POWER IFC125
Description
XP Power IFC125 Series 125 Watts Small Size Power Supply | 3.0" x 5.0" x 1.25" | Single, Triple & Quad Outputs | Active PFC
Part Number
IFC125
Price
Request Quote
Manufacturer
XP POWER
Lead Time
Request Quote
Category
Power Supply
Features
- -25 °C to +50 °C Full Power
- Active PFC - Meets EN61000-3-2, -3
- Current Share up to 4 Units
- Overvoltage & Overcurrent Protection
- Power Good Signal
- Single, Triple and Quad Outputs
- Small Size - 3.0" x 5.0" x 1.25"
Datasheet
Extracted Text
125 Watts xppower.com IFC125 Series • Small Size - 3.0” x 5.0” x 1.25” • Single, Triple and Quad Outputs • Active PFC - Meets EN61000-3-2, -3 • Current Share up to 4 Units • Overvoltage & Overcurrent Protection • Power Good Signal • -25 ˚C to +50 ˚C Full Power Specification Input General Input Voltage • 90-264 VAC Efficiency • 83% typical Input Frequency • 47-63 Hz Isolation • 3000 VAC Input to Output 1500 VAC Input to Ground Input Current • 0.8 A max at 240 VAC 500 VAC Output to Ground 1.8 A max at 100 VAC 3 Power Density • 6.66 W/In Inrush Current • 33 A max at 115 VAC 66 A max at 230 VAC Signals • Power Good - On = Logic High Power Factor • 0.98 typical MTBF • >220 kHrs per Bellcore Earth Leakage Current • 0.5 mA max at 132 VAC/60Hz 0.825 mA max at 264 VAC/50Hz Environmental Input Protection • Internal 2.6 A fuse Operating Temperature • -25 ˚C to +70 ˚C, derate linearly from 100% at +50 ˚C to 50% at +70 ˚C Output Cooling • 5 CFM airflow required for 125 W Output Voltage • See table Operating Humidity • 5-95% RH, non-condensing Output Voltage Trim • Not user-adjustable Storage Temperature • -40 ˚C to +85 ˚C Initial Set Accuracy • ±5% maximum Operating Altitude • 3000 m Minimum Load • 5 W minimum load on V1 or V2 required Shock • 15 G pk operating to maintain regulation Vibration • 2.4 G, 5 Hz to 500 Hz, 3 axis Start Up Delay • 1.5 s at 90 VAC Start Up Rise Time • 0.2-20 ms EMC & Safety Hold Up Time • >28 ms min at full load Emissions • EN55022/CISPR22 and FCC, Class Line Regulation • See table B conducted Load Regulation • See table Harmonic Currents • EN61000-3-2 Over/Undershoot • 10% maximum Voltage Flicker • EN61000-3-3 Transient Response • 5% max. deviation, recovery to within Radiated Immunity • EN61000-4-3, level 3 Perf Criteria B 1% in 500 µs for a 25% load change EFT/Burst • EN61000-4-4, level 3 Perf Criteria B Ripple & Noise • ±1% pk-pk maximum or ≤5 Vout 50 mV Surge • EN61000-4-5, level 3 Perf Criteria B maximum Conducted Immunity • EN61000-4-6 Overvoltage Protection • V1 & V2: 113-148%, auto recovery Dips & Interruptions • EN61000-4-11, 30% 10 ms, 60% 100 ms, Overtemperature • Unit shuts down, recycle input to reset 100% 5000 ms, Criteria A, B, B Protection Safety Approvals • EN60950, UL 60950, CSA950 per cUL, Overload Protection • All outputs: 115-135%, auto recovery CE Mark LVD Short Circuit Protection • Trip and restart (Hiccup mode) Temperature • 0.04% / ˚C maximum Coefficient Remote Sense • V1 only compensates for 0.5 V drop (not available on IFC125-31) Current Share • Up to 4 supplies to share within 10% 1 AC-DC AC-DC IFC125 Models and Ratings Output 1 Output 2 Output 3 Output 4 Model (1) (1) (1) (1) Vnom Imax Vnom Imax Vnom Imax Vnom Imax Number Reg Reg Reg Reg 24.0 V 5.2 A ±3% 12.0 V 0.5 A ±5% IFC125-14 5.0 V 16.5 A ±4% 12.0 V 5.0 A ±5% -12.0 V 0.5 A ±5% IFC125-31 2.5 V 12.5 A ±2% 5.0 V 15.0 A ±4% 12.0 V 5.0 A ±5% -12.0 V 0.5 A ±5% IFC125-40-1 3.3 V 10.0 A ±2% 5.0 V 15.0 A ±4% 12.0 V 5.0 A ±5% -12.0 V 0.5 A ±5% IFC125-42-3 Notes 1. Total regulation includes tolerance, line regulation and load regulation. 2. Maximum output power not to exceed 125W with 5 CFM forced air or 70W with convection cooling. 3. For IFC125-40-1 and -42-3, a maximum of 80W combined +2.5V or +3.3V and +5V outputs with 5CFM of forced air cooling or 40W with convection cooling. 4. 5W minimum load required to maintain regulation. Mechanical Details Connector Pin-outs IFC125-31 IFC125-40-1 IFC125-42-3 Conn Pin 1 Neutral Neutral Neutral J1 2 3 Line Line Line 1 -12 VDC -12 VDC -12 VDC 2 +12 VDC +12 VDC +12 VDC 3 Not Used +2.5 VDC +3.3 VDC 5.00 4 Not Used +2.5 VDC +3.3 VDC (127.0) 5 Not Used +2.5 VDC +3.3 VDC 4.55 6 DC GND DC GND DC GND 0.23 (5.7) (115.6) 7 DC GND DC GND DC GND Ø 0.16 (4.1) J2 8 DC GND DC GND DC GND (4 places) 9 DC GND DC GND DC GND 10 DC GND DC GND DC GND 11 +5 VDC +5 VDC +5 VDC 12 +5 VDC +5 VDC +5 VDC 13 +5 VDC +5 VDC +5 VDC 14 +5 VDC +5 VDC +5 VDC 3.00 3.00 J2 - DC output 1 0 V Sense 0 V Sense 0 V Sense (76.2) (76.2) 2.55 connector for J3 2 Not Used +2.5 V Sense +3.3 V Sense (64.8) IFC125-31, -40-1, Pin #1 3 Power Good Power Good Power Good 42-3. (see pin-out table) J1 - Input connector Safety ground Pin #1 Pin #1 connection point Fastener clearance area (4 places) J3 - Remote Sense/ PG connector Lock washer Screws shown for reference only 1.00 0.06 0.19 1.25 (25.4) (1.5) (4.8) (31.8) PCB Molex Mating Connectors IFC125-31 & -40-1 IFC125-42-3 Housing 09-50-8031 90-50-8033 J1 Pins 08-52-0113 08-52-0113 Notes Housing 09-50-8141 09-50-8143 1. All dimensions in inches (mm). J2 2. Weight 0.68 lb (310 g) approx (-14 models 0.6 lb, 270g). Pins 08-52-0113 08-52-0113 Housing 22-01-3037 22-01-3037 J3 Pins 08-50-0114 08-50-0114 16-Aug-05
Frequently asked questions
How does Industrial Trading differ from its competitors?
Is there a warranty for the IFC125?
Which carrier will Industrial Trading use to ship my parts?
Can I buy parts from Industrial Trading if I am outside the USA?
Which payment methods does Industrial Trading accept?
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods