PCM-DSPIO Dual Serial PC/104 MODULE and Parallel I/O F FE EA AT TU UR RE ES S � PC/104 compliant dual serial/parallel I/O module � Two independent 8250-compatible serial channels � 16-byte transmit FIFO on each channel � 16-byte receive FIFO with error flags � Modem control signals: CTS, RTS, DSR, DTR, RI, and DCD on each channel � Programmable serial interface characteristics for each channel • 5-, 6-, 7-, or 8-bit character lengths • Even, odd, or no parity generation and checking • 1, 1.5, or 2 stop bits • Local internal loopback for diagnostics � RS-232 and optional RS-485, RS-422 or J1708 electrical interface levels on both channels � Asynchronous data rates to 115,200 bps � Software programmable baud rate generator � PC-compatible parallel printer interface � Jumper selectable board I/O address � +5 volt only operation First-In First-Out (FIFO) buffer for use with high speed � 8-bit or 16-bit PC/104 stackthrough connector data communication applications. � Small size: 3.6" x 3.8" (90mm x 96mm) o o � Operating temperature: -40 C to +85 C Each channel will support 5-, 6-, 7- or 8-bit characters with even, odd or no parity generation and checking. It The PCM-DSPIO dual serial and printer interface adds will handle 1, 1.5, or 2 stop bits. Each channel can be two PC-compatible COM ports and one parallel printer set up to provide internal diagnostics such as loopback port to a PC/104 expandable system. Both serial chan- and echo mode on the data stream. nels support RS-232. As an option, RS-422/485 plus the Society of Automotive Engineers (SAE) J1708 interface Electrical Interface Levels - The board is shipped in a levels are also supported. Because of its compatibility standard configuration that supports RS-232. Only +5 with the standard PC serial and parallel ports, the PCM- volts is required for the module since it uses an inter- DSPIO is supported by operating systems, drivers, utili- face chip with a charge pump to generate the plus and ties and 3rd party libraries. minus voltages required for RS-232 levels. FUNCTIONAL CAPABILITY Optionally, RS-422/485 electrical levels can be support- ed on both serial channels. The RS-422/485 configura- PC/104 Interface - The PCM-DSPIO is I/O mapped to tion provides separate balanced transmit and receive various jumper selectable locations. Each serial channel signal pairs. For RS-485 multidrop lines, one signal requires 8 port addresses and is independently decoded pair can be used for "party line" networks. within the I/O map from COM1 to COM8. The bidirec- tional parallel port requires 4 port addresses and can be Both the RS-422/485 transmitter and receiver lines per- jumper selected for LPT1 or LPT3. mit user-installable termination resistors for impedance matching and biasing. The PCM-DSPIO card is available with either an 8-bit or 16-bit PC/104 stackthrough connector for additional WinSystems' CK-75176-2 chip kit can be ordered for interrupt support. each channel that contains two 75176B devices. The parts can be easily installed by the user. Serial Controller - A 16C552 serves as the serial com- munication controller. It has two independent, asyn- J1708 - The PCM-DSPIO can be ordered with the serial chronous channels that are 8250 hardware compatible. channels configured to support the SAE J1708 The unit contains on-chip software programmable baud electrical standard and is designated PCM-J1708. This rate generators selectable through 115,200 bits per sec- is a serial data communications link between micro- ond. Each channel has a 16-byte transmit and receive computer systems in heavy duty vehicle applications to Interrupts - Interrupts are generated on error condi- tions or receive/transmit buffer status for each of the serial channels or from the parallel I/O. Each of the 3 interrupt request channels from the 16C552 can be rout- ed to the PC/104 Bus connector. The PCM-DSPIO sup- ports IRQ channels 2, 3, 4, 5, and 7 on the 8-bit PC/104 connector plus IRQ channels 10, 11, 12, and 15 on the 16-bit PC/104 connector. Custom Configurations - For OEM applications, the PCM-DSPIO can be shipped from the factory with your specific RS-232/422/485 or J1708 configuration. Contact the factory for pricing and delivery. SPECIFICATIONS Electrical PC/104 Bus: 8- or 16-bit, stackthrough Serial: 2 RS-232 asynchronous channels. Optional RS-422/485 with the CK-75176-2 installed per channel Baud rates: 50, 110, 150, 300, 600, 1200, 2400, 4800, 7200, 9600, 19.2K, 38.4K, 56K, 115.2K Parallel: Bi-directional PC-compatible printer port PCM-DSPIO BLOCK DIAGRAM ± Vcc = +5V 5% @ 90mA typ. RS-232 channels ± +5V 5% @ 120mA typ. RS-422 channels share data cost effectively among stand-alone modules. Mechanical SAE J1708 is a modification of the RS-485 standard with Dimensions: 3.6" x 3.8" (90mm x 96mm) additional passive termination for transient and EMI PC board: 2 layer FR4 epoxy glass with suppression at the module. screened component legend Serial I/O Connector - Both serial channels are config- Connectors ured as Data Terminal Equipment (DTE) and wired Serial: One, 20-pin 0.100" grid to a 20-pin right angle connector. WinSystems offers Parallel: One, 26-pin 0.100" grid the optional CBL-173-1 which adapts each RS-232 PC/104: 64-pin, 0.100" (32-pin double row) serial channel pair to two standard 9-pin male “D” type 40-pin 0.100" (20-pin double row) connectors. Environmental o o Parallel I/O - The 16C552 chip also provides a direct Operating Temperature: -40 to +85 Celsius 26-pin Centronics parallel I/O interface from the PCM- Non-condensing relative humidity: 5% to 95% DSPIO. The port is wired as a parallel printer port but can be used for other devices. The 8 data lines are bidi- ORDERING INFORMATION rectional with a 24 mA sink capability. The additional handshake lines are dedicated with 5 bits as input only PCM-DSPIO-8 Dual Serial and Parallel, 8-bit and 4 bits as output only. PC/104 module PCM-DSPIO-16 Dual Serial and Parallel, 16-bit The parallel signal lines are wired to a 26-pin right angle PC/104 module connector. The optional WinSystems' CBL-101-3 pro- PCM-J1708 Dual SAE J1708 interface module vides a 3 foot long adapter cable designed to convert a CBL-101-3 26-pin ribbon to 25-pin male "D" 26-pin ribbon cable to a 25-pin female “D” type con- adapter to a parallel printer nector with strain relief. CBL-173-1 20-pin ribbon to two male 9-pin "D" CK-75176-2 RS-422/485 chip kit for one channel 715 Stadium Drive • Arlington, Texas 76011 • (817) 274-7553 • http://www.winsystems.com