✄ VMIACC-0576 CompactPCI Rear Transition Utility Board for VMIC’s CompactPCI SBC Boards ✪✄✰✮✄✯❊❘�✄✬❙◗❚❊❘ • Transitions parallel port, two serial ports, USB port, PMC I/O, IDE, and floppy signals from CompactPCI® (CPCI) J3 and J5 connectors to standard I/O connectors for the VMICPCI-7696, -7697, and -7710 • Provides one micro DB-25 parallel port connector • Provides two RJ45 serial port connectors • Provides enhanced IDE 40-pin connector • Provides 34-pin floppy disk drive connector • Provides one standard USB connector • Provides two standard 34-pin connectors for PMC I/O • IEEE P1101.11 compliant • CPCI Rev. 2.1 compliant • 6U height, 80 mm minimum depth INTRODUCTION — The VMIACC-0576 is designed to be used in conjunction with the VMICPCI-7696, -7697, and -7710, VMIC’s CPCI single-board computer (SBC) products. The VMIACC-0576 mounts in the rear transition area of the backplane and provides access to the serial, USB, parallel, enhanced IDE, and floppy disk connectors by way of the J3 connector, and provides PMC I/O signals by way of the Power Requirements: Power for the VMIACC-0576 J5 connector. is +5 V, supplied through the J3 connector on the CPCI The CPCI J3 and J5 connectors carry all associated backplane. signals from the 6U front mount SBCs through the backplane Temperature Range: 0 to 70 C˚ operating, forced air to the VMIACC-0576 J3 and J5 connectors (see Figure 1). cooling required HEADERS AND CONNECTORS — The two serial Relative Humidity Range: 10 to 90 percent, ports use RJ45 connectors. RJ45-to-DB9 adapter cables are noncondensing provided to connect standard D9 serial peripherals. The USB port is a standard USB connector. TRADEMARKS The serial port has jumper-selectable data carrier detect The VMIC logo is a registered trademark of VMIC. (DCD), or ring indicator (RI) signals defined by jumpers E1 CompactPCI and PICMG are registered trademarks of PCI (COM1) and E2 (COM2). Industrial Computer Manufacturers’ Group. Other registered trademarks are the property of their respective owners. The IDE and floppy are standard 40- and 34-pin header connectors, respectively. The parallel port is a micro DB-25 connector with an adapter cable supplied to a standard 25-pin D connector. Ordering Options Sept. 14, 2000 800-800576-000 B ABC – D E F IDE and floppy cabling should be limited to a maximum VMIACC-0576 –000 – of 19 inches. ABC = 000 (Options reserved for future use) The PMC I/O signals are supported on two 34-pin mass For Ordering Information, Call: 1-800-322-3616 or 1-256-880-0444 • FAX (256) 882-0859 termination connectors (AMP 103310-7). Available on the E-mail: info@vmic.com Web Address: www.vmic.com rear panel. Copyright © April 1999 by VMIC Specifications subject to change without notice. PHYSICAL/ENVIRONMENTAL Physical Dimensions: 6U single Eurocard format, single slot Height: 9.2 in. (233.4 mm) Depth: 3.15 in. (80 mm) Thickness: 0.8 in. (20.3 mm) VMIC • 12090 South Memorial Parkway • Huntsville, Alabama 35803-3308 1 ✄ VMIACC-0576 ✪✄✰✮✄✯❊❘�✄✬❙◗❚❊❘ VMICPCI-7696 Backplane VMICPCI-7697 Rear I/O VMICPCI-7710 VMIACC-0576 P5 P5 J5 J5 P4 P4 Two 34-pin PMC I/O J4 Connectors P3 J3 P3 J3 Standard USB J2 P2 Connector Micro DB-25 Floppy Parallel Port Header IDE Header P1 J1 Two RJ-45 Serial Port Connectors VMIACC-0576 Figure 1. VMIACC-0576 and Rear I/O with VMICPCI-7696, -7697, or -7710 2 For Ordering Information, Call: 1-800-322-3616 or 1-256-880-0444 • FAX (256) 882-0859