VMIC VME-1128
Specifications
Altitude Operating
0 – 10,000 ft (3,000 m)
Depth
6.3 in. (160 mm)
Height
9.2 in. (233.4 mm)
Operating Temperature
: 0° to +55° C
Power Requirements
+5 VDC (±5 percent), 2.31 A (typical)
Relative Humidity Range
20% to 80%, noncondensing
Storage Temperature
-20° to +85° C
Features
- 128 bits of high-voltage digital inputs
- A24:A16:D32/D16/D08 (EO): slave: 39/3D:29/2D
- Complies with the VMEbus Specification Rev. C.1
- Double Eurocard form factor (6U)
- Each group of eight inputs is jumper selectable to monitor voltage source or current sinking signals
- Front panel with fail LED
- High reliability DIN-type I/O connectors
- On-board Built-in-Test logic for fault detection and isolation
- Open circuit provides logic zero or (jumper-selectable) logic one
Datasheet
General electric-VME-1128-datasheet1-1562664917.pdf
328 KiB
Extracted Text
GE Intelligent Platforms VMIVME-1128* Specifications 128-bit High-Voltage Digital Input Board with Built-in-Test Features: • 128 bits of high-voltage digital inputs • Each group of eight inputs is jumper selectable to monitor voltage source or current sinking signals • Open circuit provides logic zero or (jumper-selectable) logic one • Built-in-Test logic for fault detection and isolation • Front panel with fail LED • User-selectable input voltage thresholds (0.61 to 34 V) with inputs of 0 to 66 V (see Table 1) • Complies with the VMEbus Specification Rev. C.1 • A24:A16:D32/D16/D08 (EO): slave: 39/3D:29/2D • Double Eurocard form factor (6U) • High reliability DIN-type I/O connectors • Compatible with GE’s Intelligent I/O Controllers (VMIVME-90xx series) and Universal I/O Controllers (VMIVME-9300 series) VMIVME-1128 128-bit High-Voltage Digital Input Board with Built-in-Test Addressing Scheme: Thirty-two bytes individually Ordering Options addressable on 8-, 16-, or 32-bit boundaries. A Board ID August 12, 2010 800-001128-000 J A B C D E F Register is located at the base address of the board. A Control and Status Register (CSR) is stacked above the ID VMIVME-1128 – 0 0 0 Register. The sixteen input bytes are placed above the CSR. ABC = 000 (Options reserved for future use) Twenty jumpers establish the base address of the board. Connector Data Another jumper is used for standard or short I/O accesses. The following address map shows the relative locations of all Style Description I/O Connectors the registers used by the board. Mating Connector ERNI No. 913 031 96-pin (96-pin Mass Terminated) Decoded Register Name or IDC 0.033-inch Ribbon Cable ERNI No. 913 049 Address Bits Description (96-pin Mass Terminated) Mating Connector 96-pin Harting No. 09 03 096 3214 A4 A3 A2 A1 (96-pin Discrete) Discrete Female Crimp Contacts Wire 0 0 0 0 Board ID Harting No. 09 02 000 8484 (For 96-pin Discrete) Connector Shell Housing 0 0 0 1 Control and Status Register Harting No. 09 03 096 0501 (For 96-pin Connectors) (CSR) Both PC Board Connector ERNI No. 913 216 Part Number 0 0 1 0 Not Used *The Harting crimp tool part number is 09 99 000 0075. 0 0 1 1 Not Used For Ordering Information, Call: 1-800-322-3616 or 1-256-880-0444 • FAX (256) 882-0859 0 1 0 0 Not Used Email: info.embeddedsystems.ip@ge.com Web Address: www.ge-ip.com 0 1 0 1 Not Used Copyright © 2010 GE Intelligent Platforms Embedded Systems, Inc. All Rights Reserved. 0 1 1 0 Not Used Specifications subject to change without notice. 0 1 1 1 Not Used 1 0 0 0 Input Data Word (16 bits) 0 Functional Characteristics 1 0 0 1 Input Data Word (16 bits) 1 Compliance: This product complies with the VMEbus 1 0 1 0 Input Data Word (16 bits) 2 specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297) with the following mnemonics: A24:A16:D32/D16/D08 (EO): 1 0 1 1 Input Data Word (16 bits) 3 Slave: 39/3D:29/2D Form factor: 6U 1 1 0 0 Input Data Word (16 bits) 4 Input Connector Type: Two 96-pin female connectors are 1 1 0 1 Input Data Word (16 bits) 5 used with this board. For mass terminations (IDC), an ERNI 1 1 1 0 Input Data Word (16 bits) 6 IDC DIN connector and 0.033-inch 30 AWG ribbon cable are recommended. The ERNI order numbers are: 1 1 1 1 Input Data Word (16 bits) 7 96-pin connector 913 031 Input Circuit Characteristics: The inputs are single-ended 96-conductor 0.033-inch cable 913 049 with a high input impedance (15 kΩ) and a threshold For discrete wire use, Harting connectors are recommended. accuracy of 10 percent (typical) for 3 through 66 V input This connector consists of a contact housing with female range and ±200 mV for 0 V up to 3 V input range. Refer to crimp-on contacts. Harting order numbers are: Figures 3 through 5 for typical single-ended signal conditioning configurations. Table 1 lists the threshold levels 96-pin connector 09 03 096 3214 for inputs using the stated input range. Female crimp-on contacts 09 02 000 8484 Built-in-Test: This board is designed with built-in-test logic Crimp tool (for stripped wire) 09 99 000 0075 that supports a board-level diagnostic which exercises all of Either connector needs a shell housing with holding levers. the on-board active components. Special output registers We recommend the Harting housing. Its order number is are provided to test the input circuitry. These registers are 09 03 096 0501. This shell is used with the discrete wire controlled by a test mode bit in the CSR. Thus, the user can cable, latching the discrete wire cable to the board connector monitor the data written to this board and determine if it is and providing a strain relief. functioning properly. A front panel Fail LED is provided to help in isolating a faulty board. This LED is illuminated at I/O Organization: Sixteen input ports, eight bits wide for a powerup and can be extinguished under program control total of 128 inputs, addressable to any address within the upon the successful completion of user-defined diagnostic short supervisory and/or short nonprivileged or the standard software. supervisory data and/or standard nonprivileged data I/O map. 2 VMIVME-1128 128-bit High-Voltage Digital Input Board with Built-in-Test Physical/Environmental Specifications Trademarks Dimensions: 6U Double Eurocard form factor * indicates a trademark of GE Intelligent Platforms, Inc. and/or its affiliates. All other trademarks are the property of Height 9.2 in. (233.4 mm) their respective owners. Depth 6.3 in. (160 mm) Power Requirements: +5 VDC (±5 percent), 2.31 A (typical) This power requirement is determined by the user load. Connections can be made at either the front panel (P3 or P4) or at P2. To facilitate connections made at P2, GE offers the VMIACC-0129* P2 power accessory which is recommended, but not required. Temperature: Operating: 0° to +55° C Storage: -20° to +85° C Altitude: Operating: 0 – 10,000 ft (3,000 m) Relative Humidity Range: 20% to 80%, noncondensing Cooling: Forced air convection MTBF: Contact factory Figure 1. VMIVME-1128 Block Diagram 3 VMIVME-1128 128-bit High-Voltage Digital Input Board with Built-in-Test Figure 2. Typical Input Signal Conditioning Figure 3. Input Configuration for Voltage Sourcing Inputs at TTL Levels 4 VMIVME-1128 128-bit High-Voltage Digital Input Board with Built-in-Test Figure 4. Input Configuration for Voltage Sourcing Inputs Figure 5. Input Configuration for Current Sinking Inputs 5 VMIVME-1128 128-bit High-Voltage Digital Input Board with Built-in-Test Table 1. Threshold Voltages V = 0.51 VR + 0.61 t L VRL Vt 0 V 0.61 V 1.25 V 1.25 V 5 V 3.2 V 12 V 6.7 V 24 V 12.9 V 28 V 14.8 V 48 V 25.1 V 66 V 34.3 V GE Intelligent Platforms Additional Resources Information Centers Americas: For more information, please visit the 1 800 322 3616 or 1 256 880 0444 GE Intelligent Platforms Embedded Systems web site at: Asia Pacific: 86 10 6561 1561 www.ge-ip.com Europe, Middle East and Africa: Germany +49 821 5034-0 UK +44 1327 359444 6
Frequently asked questions
How does Industrial Trading differ from its competitors?
Is there a warranty for the VME-1128?
Which carrier will Industrial Trading use to ship my parts?
Can I buy parts from Industrial Trading if I am outside the USA?
Which payment methods does Industrial Trading accept?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods