26cm COLOUR TFT- LTM10C210 PRODUCT INFORM (a-Si TFT) FEATURES 2 (1) 10.4” VGA color display with High Luminance (400cd/m) TENTATIVE (2) Wide Viewing Angle (Vertical:90, Horizontal: (3) Built in Long Life Lamps(50,000 h) (4) Full mechanical compatible with A, ” MECHANICAL SPECIFICATIONS Item Specifications Dimensional Outline (typ.) 265.0( W) x 188.8( H D) mm Number of Pixels 640( W H) pixels Active Area W) x 158.4( H) mm Pixel Pitch 0.33( W) H) Weight (approximately) 605g Backlight ABSOLUTE MAXIMUM RATINGS Item Unit Supply (V) -0.3 7.0 V (V) 0 2.0 kV(rms) FL FL Driving Frequency ( f) 0 100 FL Input Signal Voltage ( VIN) -0.3 V+0.3 V emperatureOperating T 0 50 °C emperatureStorage T -20 60 °C Storage Humidity 10 90 %(RH) (Max. wet bulb temperature = 39 ° ELECTRICAL SPECIFICATION (T °C) Item Unit Remarks Supply (V) 4.75 5.0 5.25 V (V) (500) (550) (600) V(rms) FL FL Start (1500) --- (1800) V(rms) Ta=0 °C High Level Input Voltage ( VIH) 3.5 --- V Low Level Input Voltage ( V) 0 --- 1.5 V IL Current Consumption ( I) --- 125 250 mA ( I) 3.0 6.0 7.0 mA(rms) FL Consumption --- (7.2) --- W I =6.0mA(rms) FL *1 : 8 color bars pattern OPTICAL SPECIFICATION (T °C) Item Unit Remarks Contrast Ratio ( CR) 100 250 --- --- imeResponse T (t) --- --- 50 ms ON (t) --- --- 50 ms OFF 2 Luminance ( L) 300 400 --- cd/m I=6.0mA(rms) FL *The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by oshiba or other rights of the third partieTs which may result from its use. No license is granted by implication or otherwise under any T *The information contained herein may be changed without prior notice. It is therefore advisable to contact T (1/9) -- 21 (Ver.1.0) 082000 proceeding with the design of equipment incorporating this product. before oshiba patent or patent rights of oshiba or others. Max.Typ.Min. a=25 *2 : Except the efficiency of FL inverter Power *1 *2 *2 DD *1 DD Voltage DD Voltage Max.Typ.Min. a=25 C) DD kHz DD Voltage Max.Min. Twin CCFLs, Sidelight type x 0.33( 211.2( ) x 480( ) x 12max( SVGA)LTM10C209H(10.4" VGA), LTM10C273 (10.4LTM10C209 110) ATION LIQUID CRYSTAL DISPLAY DIVISION (10.4 TYPE) LCD MODULE Unit : mm DIMENSIONAL OUTLINE TENTATIVE Standard tolerance : 0.5 8.881 4.0031+_ 0.7215.3 5.3 3 3 3 77 )aeragniweiV(4.261 )aerAevitcA(4.851 )) 0)00 0.)a...4e25a5 2.6r6e505A22r2 2(+_A( )g)9grne5enivt2iwin neet nCci eVAap((e Or A22 l..ge51n z1i1 ew22 eB i(V / 2e v. i6 t 1c 2A ( 0 . 958 5..2.93131 00 ..5.35.3 33 )retneCaerAgniweiV/evitcA(0.56 24.00.031+_. 3 0.11)gninnepOlezeB(4.361 f -1.1617.72 4 x a )m 0.70.70555 .... 2542 (1 0.80.8 (2/9) -- 21 (Ver.1.0) 082000 LTM10C210 Unit : mm DIMENSIONAL OUTLINE TENTATIVE Standard tolerance : 0.5 Pin No.3 Pin No.3 Pin No.1 Pin No.1 (High Voltage) (High Voltage) (Low Voltage) (Low Voltage) CN2 CN3 (3/9) -- 3.0 4.0 3.0 4.0 _+ 80 10 10.0 ; 4 mm MAX. height components are placed No.31 CN1 No.1 No.2 2.5 4.0 3.0 f 4- 3.6 _+ 80 10 4.0 3.0 Bezel Surface PCB I/F Connnector User side Connector Sectional figure of I/F Connector 21 (Ver.1.0) 082000 38.0 15.0 4.0 4.0 4.0 20.0 4.0 _+ 7.7 0.5 3.0 4.0 4.0 3.0 LTM10C210 BLOCK DIAGRAM CN2 Backlight CN1 X- Connector DC/DC driver IC - CN3 Backlight (4/9) -- 21 (Ver.1.0) 082000 Circuit Generation Voltage Manipulation Gray scale 640 x 480 pixels Liquid Crystal Panel Converter Controller Panel driver IC LTM10C210 TIMING CHART D D V 5 . 0% 0 1 _+ 0 5 : ) bb , a ( y at u D K L C N D D V 5 . YN0 ,3,: XY0l t,4e 96v 13e -6L NY,,rX8eY 3,t 67n2 3e-6CN ,))))XlVVVV a(((( nY5555 g,....1234YiX3131 ,Stt::::Xtt )))) tNXNX uIAIA pMMMMYn((((,I7LHLH IIIIY4VVVV,, 6X Y , 53 ,YX, 4 Y2,,3X cYg, 31t2n,YtXgi, 1n9m tDiiIA mTLT AAi VD78Tltt5a tlt6 ant co iz ti000000 rKBRGBrKBRGB eLA---oLA--- CN555CN555VH 000NERGBNERGB KBRGB ))LA--- 1CN5552 NERGB(( (5/9) -- 21 (Ver.1.0) 082000 LTM10C210 TIMING SPECIFICATION Item Symbol Unit Remarks Frame Period t1 249+N/2 x t3 t3 t3 --- 16.68 17.85 ms t2 t3 t3 48 t3 --- t t3 Displayerm T One Line t3 t5 t5 t5 --- Scanningime T 31.5 31.78 --- ms Horizontal t4 t5 t5 t5 --- Displayerm T Clock Period t5 35.0 39.72 --- ns Clock “L”ime T t6 10.0 --- --- ns Clock “H”ime T t7 7.0 --- --- ns t8 5.0 --- --- ns imeHold T t9 10.0 --- --- ns Note 1) When ENAB is fixed to “H” level or “L” level after NCLK input, the panel is displayed as black. However, it may be occurred a flicker on the displa.y Note 2) When NCLK is fixed to “H” level or “L” level, the panel becomes white stage after several seconds. Note 3) Do not change t1 and t3 values in the operation. When t1 or t3 is changed, the panel is displayed as black. Note 4) Please adjust LCD operating signal timing and FL driving frequency, to optimize the display quality. There is a possibility that flicker is observed by the interference of LCD operating signal timing and FL driving condition (especially driving frequency). Note 5) When the vertical display period (N) is shorter than 480 lines, the actual display area is shifted to the cente Non-display areas become dark as follows. Note 5) The following conditions should be met. a. NCLK count of each Horizontal Scanning Time should be always the same. b. V-Blanking period should be "n" x "Horizontal Scanning Time". (n=integer) c. Frame period should be always the same. x, 1 (6/9) -- 21 (Ver.1.0) 082000 640, N1, N x, y1, y 480 lines 1, 2 640, 12, 11, 1 640 pixels r. Set Up Time 640 x 640 x 640 x 860 x 800 x 684 x 2=N x 0 x 480 x 300 x Vertical 525 x 525 x Max.Typ.Min. 1) 2) 3) 4) 5) 6) LTM10C210 CONNECTOR PIN ASSIGNMENT FOR INTERFACE CN1 INPUT SIGNAL Connector : DF9B-31P- Mating Connector : DF9*-31S-1V / HIRO erminal No.T Symbol Function 1 2 3 4 R0 RED DISPL 5 R1 RED DISPL 6 R2 RED DISPL 7 8 R3 RED DISPL 9 R4 RED DISPL 10 R5 RED DISPL 12 13 14 15 16 17 18 19 20 21 22 B0 BLUE DISPL 23 B1 BLUE DISPL 24 B2 BLUE DISPL 25 26 B3 BLUE DISPL 27 B4 BLUE DISPL 28 B5 BLUE DISPL 29 V 30 +5V POWER SUPP 31 V +5V POWER SUPP CN2 CCFLWER SOURCE Connector : BHR-03VS-1 / JA Mating Connector : SM02(8.0)B--1 / JA erminal No.T Symbol Function 1 V Supply ( high voltage) FLH1 1) 2 NC Non Connection (open) V 3 FLL1CCFL Power Supply (low voltage) CN3 CCFLWER SOURCE Connector : BHR-03VS-1 / JA Mating Connector : SM02(8.0)B--1 / JA erminal No.T Symbol Function 1 V CCFL Power Supply ( high voltage) FLH2 1) 2 NC Non Connection (open) 3 V CCFL Power Supply (low voltage) FLL2 Note 1) NC terminal should be open. (7/9) -- 21 (Ver.1.0) 082000 AL MFG CO., LTD.PAN SOLDERLESS TERMINBHS PAN SOLDERLESS TERMINAL MFG CO., LTD. PO CCFL Power PAN SOLDERLESS TERMINAL MFG CO., LTD.BHS PAN SOLDERLESS TERMINAL MFG CO., LTD. PO LYDD LY DD GND AY DATA (MSB) AY DATA AY DATA GND AY DATA AY DATA AY DATA (LSB) GND ND SYNCHRONIZATION SIGNALCOMPOUENAB GND GREEN DISPLAY DATA (MSB)G5 GREEN DISPLAY DATAG4 GREEN DISPLAY DATAG3 GND GREEN DISPLAY DATAG2 GREEN DISPLAY DATAG1 GREEN DISPLAY DATA (LSB)G0 GND11 AY DATA (MSB) ATA AY D AY DATA GND AY DATA AY DATA AY DATA (LSB) GND SAMPLING CLOCKNCLK GND SE ELECTRIC CO., LTD. ( * : option mark) 1V / HIROSE ELECTRIC CO., LTD. LTM10C210 TM10C210 256k (k=1024) COLORS COMBINATION TABLE Gray Scale Display Level R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 Black L L L L L L L L L L L L L L L L L L - Blue L L L L L L L L L L L L H H H H H H - Green L L L L L L H H H H H H L L L L L L - Basic Light Blue L L L L L L H H H H H H H H H H H H - Color Red H H H H H H L L L L L L L L L L L L - Purple H H H H H H L L L L L L H H H H H H - H H H H H H H H H H H H L L L L L L - White H H H H H H H H H H H H H H H H H H - Black L L L L L L L L L L L L L L L L L L L 0 L L L L L H L L L L L L L L L L L L L 1 Dark L L L L H L L L L L L L L L L L L L L 2 Scale of ­ : : : L3¼ Red ¯ : : : L60 Light H H H H L H L L L L L L L L L L L L L61 H H H H H L L L L L L L L L L L L L L62 Red H H H H H H L L L L L L L L L L L L Red L63 Black L L L L L L L L L L L L L L L L L L L 0 L L L L L L L L L L L H L L L L L L L 1 Dark L L L L L L L L L L H L L L L L L L L 2 Scale of ­ : : : L3¼ Green ¯ : : : L60 Light L L L L L L H H H H L H L L L L L L L61 L L L L L L H H H H H L L L L L L L L62 Green L L L L L L H H H H H H L L L L L L Green L63 Black L L L L L L L L L L L L L L L L L L L 0 L L L L L L L L L L L L L L L L L H L 1 Dark L L L L L L L L L L L L L L L L H L L 2 Scale of ­ : : : L3¼ Blue ¯ : : : L60 Light L L L L L L L L L L L L H H H H L H L61 L L L L L L L L L L L L H H H H H L L62 Blue L L L L L L L L L L L L H H H H H H Blue L63 Black L L L L L L L L L L L L L L L L L L L 0 L L L L L H L L L L L H L L L L L H L 1 Scale of Dark L L L L H L L L L L H L L L L L H L L 2 White & ­ : : : L3¼ Black ¯ : : : L60 Light H H H H L H H H H H L H H H H H L H L61 H H H H H L H H H H H L H H H H H L L62 White H H H H H H H H H H H H H H H H H H White L63 (8/9) -- 21 (Ver.1.0) 082000 Gray Gray Gray Gray Yellow ! FOR SAFETY In using our Modules, make certain that you fully understand and put into practice the warnings and safety precautions - Refer to individual specifications and TECHNICAL DA sheets (hereinafter called "TD") for more detailed technical 1) SPECIAL PURPOSES A) Toshiba's Standard LCD Modules have not been customized for operation in extreme environments or for use in - Toshiba's Standard LCD Modules have not been designed for operation in extreme environB) Since ments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which exceed Toshiba's published specification limits. C) In addition, since Toshiba Standard LCD Modules have not been designed for use in applications where performance failures could be life-threatening or catastrophic, they must never be installed in aircraft navigation control systems (such as, but not limited to Traffic Collision Avoidance System and Air Traffic Indicator), in military defense or weapons systems, in critical industrial process-control systems (e.g., those involved in the production of nuclear energy), or in critical medical -support systems. 2) DISASSEMBLING OR MODIFICATION DO NOT DISASSEMBLE OR MODIFY the module. It may damage sensitive parts inside LCD module, and may cause .scratches or dust on the display T 3) BREAKAGE OF LCD PANEL DO NOT INGEST liquid crystal material, DO NOT INHALE this material, and DO NOT CONTACT the material with skin, if .y If this material contact wi 4) GLASS OF LCD PANEL 5) ELECTRIC SHOCK DO NOT TOUCH the parts inside LCD module and the fluorescent lamp's connector or cables in order to prevent electric 6) ABSOLUTE MAXIMUM RATINGS AND POWER PROTECTION CIRCUIT DO NOT EXCEED the absolute maximum rating values under the worst probable conditions caused by the supply voltage variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise LCD module may y 7) DISPOSAL (9/9) -- 21 (Ver.1.0) 082000 icable environmental regulations.When dispose LCD module, obey to the appl Suitable protection circuit should be applied for each system design. Employ protection circuit for power suppl, whenever the specification or TD specifies it. be damaged. shock, because high voltage is supplied to these parts from the inverter unit while power supply is turned on. handling LCD module.DISCONNECT POWER SUPPLY before BE CAREFUL WITH CHIPS OF GLASS that may cause injuring fingers or skin, when the glass is broken. th skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water. If liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediatel LCD panel is broken and liquid crystal material spills out. the module, if customer disassembled or modified it.doses not warrantoshiba device or patient life threatening or otherwise catastrophic.applications where performance failures could be life information. AT FOR TOSHIBA LCD MODULES".N001,"CAUTIONS AND INSTRUCTIONSNo.EEdetailed in Engineering Information thin mechanical dimensions.weightedodule is generally designed with precise parts to achieve light LCD m LTM10C210