4KB Serial EEPROM

The 4KB serial EEPROM device is non-volatile memory. This storage area is completely user-defined. For instructions on accessing this device, contact TEKNOR’s Technical Support.

Basic Interface Devices

Supports PS/2 keyboard, PS/2 mouse, AT standard keyboard, speaker, reset switch and hard disk LED.

Battery

A built-in lithium battery is provided for data retention of CMOS memory.

Boot Block Flash BIOS

The 256KB boot block flash device contains all the board’s BIOSs and it is used for storing the nonvolatile configuration required for Plug and Play. Protected boot block section allows for reprogramming of BIOS. The main BIOS is an AWARD BIOS with ACPI, APM, DMI, Green and PnP features.

Bus Support

ISA Bus IEEE P996 Specification: 16-bit standard, high drive ISA buffers. PCI Local Bus Specification, Revision 2.1. PCI Industrial Computer Manufacturers Group (PICMG) 2.0 Specification.

CompactFlash Disk Option

This module is a daughterboard with available capacities of 4, 10, 15, 20 or 24 MB. The CompactFlash is connected to the secondary IDE interface and configured as a master or slave disk. It is bootable and completely user upgradable (will support higher capacities when available).

CPU Module Option

The Intel Mobile Pentium II (MPII) processor at 233, 266, and 300MHz (maximum internal CPU clock speeds). Upgradable with future MPII processor speeds via the 240-pin BGA socket.

Enhanced IDE Ultra DMA/33 Interface

Can drive up to four enhanced IDE devices. Supports PIO mode 4 and Ultra DMA/33 with S.M.A.R.T. capability.

Floppy Interface

Supports two floppy disk drives from 360KB to 2.88MB.

In-Target Probe (ITP) Connector Footprint

The board provides the footprint to allow the user to install an ITP connector, typically used for connection to an In-Circuit Emulator (ICE). For more detail, contact TEKNOR’s Technical Support.

Internal Secondary Cache

512 KB, pipelined burst cache, operates at half the maximum internal CPU clock speed, Error Checking and Correction (ECC) capable.

Operating Systems

Supports all operating systems developed for x86 and Pentium

Parallel Port

Supports multiple modes (Standard, EPP and ECP).

PC/104 and PC/104-Plus

PC/104 ISA expansion header and PC/104-Plus PCI expansion header are available onboard.

PCI Ethernet Interface

Intel 82558 Ethernet controller supports 10Base-T and 100Base-Tx Ethernet interface options via an RJ-45 connector on the board’s I/O bracket. LED indicators are supported on the connector. Software drivers are supported for the most popular operating systems.

PCI SCSI Interface

The SCSI controller - Adaptec AIC-7880 - supports Wide-Ultra SCSI (16-bit, 40MB per second) via the 68-pin Wide-Ultra SCSI connector. It also supports Fast SCSI II (8-bit, 10MB per second) and Fast-20 SCSI II (8-bit, 20MB per second) via the 50-pin SCSI header. Active termination is provided onboard (enabled by jumpers). A SCSISelect Configuration Utility is available. Software drivers are supported for the most popular operating systems.

Serial ID Number Device

The 48-bit serial number device contains the board’s unique serial number. The number can be read by software. For instructions on accessing this device, contact TEKNOR’s Technical Support.

Serial Ports

Supports two RS-232 serial ports, with RS-422/RS-485 available on Serial Port 2. Serial ports are 16C550 compatible with internal 16-byte FIFO buffers for more efficient data transfers.

Supervisor Utilities

Include a two-stage Watchdog Timer supervisory circuit, a power fail / low battery detector circuit, and a CPU temperature sensor / alarm included in the processor module.

System Memory

- From 8 to 384MB using Synchronous DRAM (SDRAM), or from 8 to 768MB

Universal Serial Bus (USB)

Supports two USB ports with optional cable/assembly bracket. The USB is an interface allowing for connectivity to many standard PC peripherals via an external port.

Video Option

The video system includes an integrated PCI 64-bit CRT / Flat Panel video controller (CL-GD7556) with 2 MB video memory (EDO DRAM). Software drivers are available for the most popular operating systems. These onboard video connectors are available: CRT, Flat Panel, PanelLink, TV-OUT and V-PORT. The V-PORT connector supports TEKNOR’s TEK-380 Video Camera Interface Module (VIPer Vision).

Voltage Regulators

Onboard switching regulator used for 1.7V (VCORE and GTL+ termination) and for 3.3VDC (VIO) power supplies. Also linear regulators for L2 cache (1.8V) and processor module CMOS pull-up voltages (2.5V).