DISABLED FAULT ENABLED POWER GOOD ® CompactPCI SYSTEM POWER SUPPLIES CPCI SERIES 150 to 350 Watts, Ac Input with PFC DPCI SERIES 150 to 350 Watts, 48 Vdc Input EXECUTIVE MEMBER FEATURES:  150 W and 200 W in 3U x 8HP, 350 W in 6U x 8HP ®  Fully compliant with PICMG CompactPCI speciŢ cations • Current sharing and internal OR-ing diodes for N+1 redundancy • High current 5 V and 3.3 V outputs ® • CompactPCI package requires only 15 cfm of external cooling air • Universal ac input versions with power factor correction • 48 Vdc input versions The CPCI series (ac input) and DPCI series (dc input) are highly reliable power supplies for CompactPCI systems, which are increasingly used in communications, industrial, military/aerospace, and other applications. These power supplies offer high power density in plug-in modules ® that meet the requirements of the PICMG power interface speciŢ cation for CompactPCI systems. These units may be used as a single power supply for a CompactPCI system, or multiple units may be used in parallel for higher power capabil- ity as needed. In addition, all units include current sharing, internal OR-ing diodes, and a hot plug input/output connector to offer full hot swap capability and N+1 redundancy. Also, compatible ac and dc input units offer standardization on a single power supply series for a system mechanical conŢ guration. 3U x 8 HP 6U x 8 HP INPUT FAULT Connector Input Power Model No. Connector Input Power Model No. 47 Pin Modular 150 W CPCI-154-1203 47 Pin Modular Ac 350 W CPCI-354T-1203 Ac 200 W CPCI-204-1203 Dc 350 W DPCI-354T-1203 150 W DPCI-154-1203 38 Pin Modular Ac 350 W CPCI-354-1203 Dc 200 W DPCI-204-1203 Dc 350 W DPCI-354-1203 DIN “M” 150 W CPCI-154-1203M Ac 200 W CPCI-204-1203M 150 W DPCI-154-1203M Dc 200 W DPCI-204-1203M Condor D.C. Power Supplies, Inc.  2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com ® CompactPCI SYSTEM POWER SUPPLIES CPCI SERIES 150 to 350 WATTS, AC INPUT WITH PFC, QUAD OUTPUT, HOT SWAP SPECIFICATIONS EMI: CONDUCTED RFI AC INPUT: 90-264 Vac continuous range, 47 to 63 Hz. Meets FCC Part 15, Subpart J, class A; POWER FACTOR: 0.99 typical at full load. Meets EN61000-3-2. EN55022 class A; CISPR 22 class A. INRUSH: CPCI-154, 204 MODELS: Cold start ac current is less than 15 A at FAIL# SIGNAL: TTL compatible signal. Signal goes low 115 Vac, and 30 A at 230 Vac. Limited by thermistor. under the following conditions: CPCI-354 MODELS: Cold start ac current is less than 30 A at CPCI-154 & CPCI-204 Models (all connector types): 115 Vac, and 60 A at 230 Vac. Limited by thermistor. Outputs #1 or #2 fail; an overcurrent condition on outputs #1, #2, or #3; an overtemperature shutdown; an overvoltage BROWNOUT PROTECTION: Holds regulation to 85 Vac shutdown; or an ac input failure (5 ms warning before outputs (30 seconds maximum) shutdown). HOLDUP TIME: 16 ms minimum after removal of power at full load. CPCI-354 & CPCI-354T Models: 10 ms minimum for CPCI 200s. Any of 4 outputs fail; an overtemperature shutdown; an EFFICIENCY: 70% typical. overvoltage shutdown; or an ac input failure (5 ms warning before outputs shut down). AC INPUT Min. Load Maximum Output Model Power Output 1 Output 2 Output 3 Output 4 on V1* From V1 & V2 CPCI-154-1203 150 W 5.0 V @ 25A 3.3 V @ 20 A 12 V @ 5.5 A -12 V @ 0.5 A 2.5 A 25 A CPCI-154-1203M 150 W 5.0 V @ 25 A 3.3 V @ 20 A 12 V @ 5.5 A -12 V @ 0.5 A 2.5 A 25 A CPCI-204-1203 200 W 5.0 V @ 25 A 3.3V @ 30 A 12 V @ 5.5 A -12 V @ 0.5 A 3.0 A 35 A CPCI-204-1203M 200 W 5.0 V @ 25 A 3.3 V @ 25 A 12 V @ 5.5 A -12 V @ 0.5 A 2.5 A 35 A CPCI-354-1203 350 W 5.0 V @ 50 A 3.3 V @ 40 A 12 V @ 12 A -12 V @ 4 A 5.0 A 65 A CPCI-354T-1203 350 W 5.0 V @ 50 A 3.3 V @ 40 A 12 V @ 12 A -12 V @ 4 A 5.0 A 65 A * For full output current capability on V2, V3, V4. DPCI SERIES 150 to 350 WATTS, QUAD OUTPUT, 48 VDC INPUT, HOT SWAP SPECIFICATIONS DC INPUT: 36-72 Vdc EFFICIENCY: 75% typical FAIL# SIGNAL: TTL compatible signal. Signal goes low under the following conditions: Any of 4 outputs fail; an overtemperature shutdown; or an overvoltage shutdown. 48 VDC INPUT Min. Load Maximum Output Model Power Output 1 Output 2 Output 3 Output 4 on V1* From V1 & V2 DPCI-154-1203 150 W 5 V @ 25 A 3.3 V @ 20 A 12 V @ 5.5 A -12 V @ 0.5 A 2.5 A 25 A DPCI-154-1203M 150 W 5 V @ 25 A 3.3 V @ 20 A 12 V @ 5.5 A -12 V @ 0.5 A 2.5 A 25 A DPCI-204-1203 200 W 5 V @ 25 A 3.3 V @ 30 A 12 V @ 5.5 A -12 V @ 0.5 A 3.0 A 35 A DPCI-204-1203M 200 W 5 V @ 25 A 3.3 V @ 25 A 12 V @ 5.5 A -12 V @ 0.5 A 2.5 A 35 A DPCI-354-1203 350 W 5 V @ 50 A 3.3 V @ 40 A 12 V @ 12 A -12 V @ 4 A 5.0 A 65 A DPCI-354T-1203 350 W 5 V @ 50 A 3.3 V @ 40 A 12 V @ 12 A -12 V @ 4 A 5.0 A 65 A * For full output current capability on V2, V3, V4. Condor D.C. Power Supplies, Inc.  2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com ® CompactPCI SYSTEM POWER SUPPLIES GENERAL SPECIFICATIONS OUTPUT ENVIRONMENTAL LINE & LOAD REGULATION: COOLING ± 2% over input range and 0 to 100% load change. 150 to 200 Watt: 15 cfm, 225 lfm airţ ow required for cooling. RIPPLE & NOISE 350 Watt: 1% p-p or 50 mV, whichever is greater. 30 cfm, 450 lfm airţ ow required for cooling. Measured at mating connector with 20 µF OUTPUT ISOLATION REMOTE SENSE Isolated from ground 50 Vdc (leakage current <20 µA) Open sense lead protection THERMAL PROTECTION TEMPERATURE COEFFICIENT Shuts down power supply if overheated. (Outputs #1 and 2): 0.03% per degree centigrade Automatic recovery. STABILITY TEMPERATURE RANGE 0.1% over 8 hours after 30 minutes warm-up. 0 to 40º centigrade at full ratings; derate 2.5% per degree centigrade from 40º to 70º centigrade. TRANSIENT RESPONSE Unit will start up at -20º centigrade. (Outputs #1 and 2): Output voltage returns to within 1% in less than 1 ms for a 50% load change. Peak transient MISCELLANEOUS does not exceed 5%. SAFETY AGENCY APPROVALS OVERVOLTAGE PROTECTION Models are approved to UL1950; CSA 22.2 #234; (Outputs #1 and #2): Protects load against power supply IEC 950 and TUV EN60950, Class 1 SELV., induced overvoltage. Trip-point is factory set so that CE 72/23/EEC/93/68EEC (low voltage directive). output voltage cannot exceed 136% of nominal. Input power must be recycled to reset. GUARANTEED FOR 2 YEARS Two year guarantee includes labor and parts. OVERLOAD PROTECTION Guarantee applies to operation at full published All outputs are protected against overload and short speciŢ cations at the end of 2 years. circuit, Automatic recovery upon removal of fault. DEG# SIGNAL : OPTIONS TTL compatible signal. Signal goes low 20ºC before an overtemperature shutdown. LOW LEAKAGE FAIL LED : (CPCI Models only) Amber LED illuminates upon a failure condition as per “L” option: Leakage current less than 0.5 mA per unit. Will the CPCI and DPCI series speciŢ cations. require additional Ţ ltering for compliance to EMI speciŢ ca- tions. STATUS LED : Green LED illuminates with no presence of any failure condition. MECHANICAL DIMENSIONS REMOTE ENABLE CPCI-154, CPCI-204, DPCI-154 & DPCI-204 Models: Contact closure to common turns on dc outputs. 3U x 8HP W, 160 mm board depth (see outline drawing). Recessed pin for “make last, break Ţ rst” connection. Utilizes a 47 pin modular connector in accordance with ® PICMG Power Interface SpeciŢ cation 2.11. REMOTE INHIBIT Contact closure to the negative sense line or a TTL CPCI-154M, CPCI-204M, DPCI-154M & level “0” turns off dc outputs. DPCI-204M Models: 3U x 8HP W, 160 mm board depth (see outline drawing). ® REDUNDANCY Utilizes a DIN “M” connector as referenced in the PICMG Built-in ORing diodes, slope program current sharing on Power Interface SpeciŢ cation 2.11. all outputs, and self aligning connector provide hot swap and N+1 capabilities. Current sharing remains within CPCI-354, DPCI-354 Models: 10% of the unit’s full output rating while units are in 6U x 8HP W, 160 mm board depth (see outline drawing). thermal equilibrium. Utilizes a 38 pin modular connector as referenced in the ® PICMG Power Interface SpeciŢ cation 2.11. REVERSE VOLTAGE Protected against reverse voltage up to supply CPCI-354T, DPCI-354T Models: current rating. except for reverse voltage on output #4 6U x 8HP W, 160 mm board depth (see outline drawing). on CPCI-200. Utilizes a 47 pin modular connector in accordance with Condor D.C. Power Supplies, Inc.  2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com ® CompactPCI SYSTEM POWER SUPPLIES POWER SUPPLY PIN ASSIGNMENTS Model: CPCI-354-1203 Model: DPCI-354-1203 Connector: Positronics PCI38M400A1 Connector: Positronics PCI38M400A1 Mating Connector: PCI38F300A1 Mating Connector: PCI38F300A1 Pin No. Designation Pin No. Designation Pin No. Designation Pin No. Designation 1 +5 V 20 Not Used 1 +5 V 20 Not Used 2 +5 V 21 -12 V 2 +5 V 21 -12 V 3 +5 V 22* GND 3 +5 V 22* GND 4 +5 V 23 GND 4 +5 V 23 GND 5 GND 24 +5 V Sense 5 GND 24 +5 V Sense 6 GND 25* Enable 6 GND 25* Enable 7 GND 26 Sense Return 7 GND 26 Sense Return 8 GND 27 +3.3 V Sense 8 GND 27 +3.3 V Sense 9 GND 28* Not Used 9 GND 28* Not Used 10 GND 29 DEG# 10 GND 29 DEG# 11 GND 30 +12 V Sense 11 GND 30 +12 V Sense 12 GND 31 Inhibit 12 GND 31 Inhibit 13 +3.3 V 32 Not Used 13 +3.3 V 32 Not Used 14 +3.3 V 33 Not Used 14 +3.3 V 33 Not Used 15 +3.3 V 34 Not Used 15 +3.3 V 34 Not Used 16 +3.3 V 35 Fail # 16 +3.3 V 35 Fail # 17 GND 36** Safety Ground 17 GND 36** Safety Ground 18 +12 V 37 Ac Neutral 18 +12 V 37 -48 Vdc Input Return 19 Not Used 38 Ac Line 19 Not Used 38 -48 Vdc Input * Pins 22,25, and 28 are last mate, Ţ rst break pins. * Pins 22, 25, and 28 are last mate, Ţ rst break pins. ** Pin 36 is a Ţ rst mate, last break pin. ** Pins 36 is a Ţ rst mate, last break pin. Model: CPCI-354T-1203 Model: DPCI-354T-1203 CPCI-154-1203 DPCI-154-1203 CPCI-204-1203 DPCI-204-1203 Connector: Positronics PCI47M400A1 Connector: Positronics PCI47M400A1 Mating Connector: PCI47F300A1 Mating Connector: PCI47F300A1 Pin No. Designation Pin No. Designation Pin No. Designation Pin No. Designation 1 +5 V 25 Not Used 1 +5 V 25 Not Used 2 +5 V 26 Not Used 2 +5 V 26 Not Used 3 +5 V 27* Enable 3 +5 V 27* Enable 4 +5 V 28 Not Used 4 +5 V 28 Not Used 5 GND 29 Not Used 5 GND 29 Not Used 6 GND 30 +5 V Sense 6 GND 30 +5 V Sense 7 GND 31 Not Used 7 GND 31 Not Used 8 GND 32 Not Used 8 GND 32 Not Used 9 GND 33 +3.3 V Sense 9 GND 33 +3.3 V Sense 10 GND 34 Sense Return 10 GND 34 Sense Return 11 GND 35 Not Used 11 GND 35 Not Used 12 GND 36 +12 V Sense 12 GND 36 +12 V Sense 13 +3.3 V 37 Not Used 13 +3.3 V 37 Not Used 14 +3.3 V 38 DEG# 14 +3.3 V 38 DEG# 15 +3.3 V 39 Inhibit 15 +3.3 V 39 Inhibit 16 +3.3 V 40 Not Used 16 +3.3 V 40 Not Used 17 +3.3 V 41 Not Used 17 +3.3 V 41 Not Used 18 +3.3 V 42 Fail # 18 +3.3 V 42 Fail # 19 GND 43 Not Used 19 GND 43 Not Used 20 +12 V 44 Not Used 20 +12 V Output 44 Not Used 21 -12 V 45** Safety Ground 21 -12 V Output 45** Safety Ground 22 GND 46 Ac Neutral 22 GND 46 -48 Vdc Input Return 23 Not Used 47 Ac Line 23 Not Used 47 -48 Vdc Input 24 GND 24 GND * Pin 27 is a last mate, Ţ rst break pin. * Pin 27 is a last mate, Ţ rst break pin. ** Pin 45 is a Ţ rst mate, last break pin. ** Pin 45 is a Ţ rst mate, last break pin. Model: CPCI-154-1203M Model: DPCI-154-1203M CPCI-204-1203M DPCI-204-1203M Male Connector: DIN 41612 Type “M” Male Connector: DIN 41612 Type “M” Mating Connector: ERNI #914374 or AMP#148370 Mating Connector: ERNI #914374 or AMP#148370 Pin No. Designation Pin No. Designation Pin No. Designation Pin No. Designation A13 Not Used B17 +3.3 V A13 Not Used B17 +3.3 V A14 Inhibit B18 +3.3 V A14 Inhibit B18 +3.3 V A15 Not Used B19 +12 V Output A15 Not Used B19 +12 V Output A16 Sense Return B20 -12 V Output A16 Sense Return B20 -12 V Output A17 +5 V Sense B22 +5 V A17 +5 V Sense B22 +5 V A18 +3.3 V Sense B25 GND A18 +3.3 V Sense B25 GND A19 +12 V Output B28 Not Used A19 +12 V Output B28 -48 Vdc Input Return A20 -12 V Output B31 Not Used A20 -12 V Output B31 -48 Vdc Input B2 Ac Line C13 Enable B2 Not Used C13 Enable B5 Not Used C14 DEG# B5 Ac Neutral C14 DEG# B8 Not Used C15 Fail # B8 Not Used C15 Fail # B11 Chassis Ground C16 +3.3 V B11 Chassis Ground C16 +3.3 V B13 +3.3 V C17 +3.3 V B13 +3.3 V C17 +3.3 V B14 +3.3 V C18 +3.3 V B14 +3.3 V C18 +3.3 V B15 +3.3 V C19 +12 V Output B15 +3.3 V C19 +12 V Ouput B16 +3.3 V C20 -12 V Output B16 +3.3 V C20 -12 V Ouput Condor D.C. Power Supplies, Inc.  2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com ® CompactPCI SYSTEM POWER SUPPLIES MECHANICAL SPECIFICATIONS: CPCI-154, DPCI-154 CPCI-204, DPCI-204 150-200 Watts WEIGHT 1.5 LBS - 0.68 KG FRONT VIEW SIDE VIEW REAR VIEW .57 14.47 C L 1.26 .23 1.59 32.00 5.8 40.39 .199 5.06 P47 .642 16.3 INPUT FAULT 6.67 169.58 5.06 128.5 3.93 99.8 3U x 8HP EMC FRONT PANEL CARD EXTRACTOR DIMENSIONS: INCHES MILLIMETERS CPCI-154M, DPCI-154M CPCI-204M, DPCI-204M 150-200 Watts WEIGHT 1.58 LBS .72 KG SIDE VIEW REAR VIEW FRONT VIEW 1.59 40.39 1.00 .80 C L 1.37 .12 .50 .25 1.441 B11 (36.61mm) FAULT 6.62 A13 INPUT C13 4.82 168.14 J1 5.06 128.5 B31 .12 3.930 99.82 PANEL FASTENER M2.5 COLLAR SCREW 4PL. 3U x 8HP EMC FRONT PANEL DIMENSIONS: INCHES MILLIMETERS Condor D.C. Power Supplies, Inc.  2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com DISABLED FAULT ENABLED POWER GOOD ® CompactPCI SYSTEM POWER SUPPLIES MECHANICAL SPECIFICATIONS: CPCI-350T, DPCI-350T WEIGHT 3.8 LBS 1.7 KGS CENTER OF THE GUIDE RAIL TO THE .228±.010 CENTER OF PIN 47 (POSITRONIC INC. 350 Watts CONNECTOR, PN PCI47M400A1) 1.59 40.39 6U X 8HP PIN 47 MAX POSITRONICS CONNECTOR PCI47M400A1 TO MATE WITH PCI47F300A1 .485 GUIDE RAIL TO CENTER OF PIN 47 9.19 233.43 10.32MAX 261.90MAX 8.99 228.35 .56 6.504 .258 1.27 165.20 1.37 CARD EXTRACTOR DIMENSIONS: INCHES RAIL 2PL C MILLIMETERS L WEIGHT 3.8 LBS 1.7 KGS 350 Watts .29±.010 CENTER OF THE GUIDE RAIL TO 1.59 THE CENTER OF PIN 38 7.54 40.34 PIN 38 POSITRONICS CONNECTOR PCI138400A1 TO MATE WITH PCI138F300A1 .49 12.5 GUIDE RAIL TO CENTER OF PIN 38 9.19 233.43 10.31 261.90 8.99 228.35 .56 6.50 1.34 .26 34.04 165.20 6.55 6U X 8HP 1.46 CARD EXTRACTOR 37.08 DIMENSIONS: INCHES RAIL 2PL MILLIMETERS 3/01 Condor D.C. Power Supplies, Inc.  2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com