® PowerLogic Series 800 Power Meter PM820, PM850, and PM870 63230-500-225A1 Retain for future use. Reference manual HAZARD CATEGORIES AND SPECIAL SYMBOLS Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this bulletin or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure. The addition of either symbol to a “Danger” or “Warning” safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING WARNING indicates a potentially hazardous situation which, if not avoided, can result in death or serious injury. CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury. CAUTION CAUTION, used without the safety alert symbol, indicates a potentially hazardous situation which, if not avoided, can result in property damage. NOTE: Provides additional information to clarify or simplify a procedure. PLEASE NOTE Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. i © 2006 Schneider Electric. All Rights Reserved. CLASS A FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This Class A digital apparatus complies with Canadian ICES-003. © 2006 Schneider Electric. All Rights Reserved. ii 63230-500-225A1 Power Meter PM800 Series 6/2006 Table of Contents CHAPTER 1—TABLE OF CONTENTS CHAPTER 1—INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Topics Not Covered in This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 What is the Power Meter? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Power Meter Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Power Meter With Integrated Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Power Meter Without Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Power Meter With Remote Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Power Meter Parts and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Box Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 CHAPTER 2—SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 CHAPTER 3—OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Operating the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 How the Buttons Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Changing Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Menu Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Set Up the Power Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Power Meter With Integrated Display Communications Setup . . . . . . . . . . . . . . . . . . . . 17 Power Meter With Remote Display Communications Setup . . . . . . . . . . . . . . . . . . . . . . 18 Comm1 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Comm2 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Set Up the Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Set Up the Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Set Up the Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Set Up CTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Set Up PTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Set Up Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Set Up the Meter System Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Set Up Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Set Up I/Os . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Set Up the Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Set Up the Operating Time Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Advanced Power Meter Setup Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Set Up the Phase Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Set Up the Incremental Energy Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Set Up the THD Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Set Up the VAR/PF Convention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Set Up the Lock Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Set Up the Alarm Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Set Up the Bar Graph . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Set Up the Power Demand Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Set Up the EN50160 Evaluation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Power Meter Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Initialize the Power Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 © 2006 Schneider Electric All Rights Reserved iii Power Meter PM800 Series 63230-500-225A1 Table of Contents 6/2006 Reset the Accumulated Energy Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Reset the Accumulated Demand Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Reset the Minimum/Maximum Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Change the Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Reset the Accumulated Operating Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Power Meter Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 View the Meter Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Check the Health Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Read and Write Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 View the Meter Date and TIme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 CHAPTER 4—METERING CAPABILITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Real-Time Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Min/Max Values for Real-time Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Power Factor Min/Max Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Power Factor Sign Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Demand Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Demand Power Calculation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Block Interval Demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Synchronized Demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Thermal Demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Demand Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Predicted Demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Peak Demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Generic Demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Input Metering Demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Energy Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Energy-Per-Shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Power Analysis Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 CHAPTER 5—INPUT/OUTPUT CAPABILITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Demand Synch Pulse Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Relay Output Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Solid-state KY Pulse Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 2-wire Pulse Initiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Calculating the Kilowatthour-Per-Pulse Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Analog Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 CHAPTER 6—BASIC ALARMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 About Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Basic Alarm Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Setpoint-driven Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Priorities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Viewing Alarm Activity and History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Types of Setpoint-controlled Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Scale Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 © 2006 Schneider Electric All Rights Reserved iv 63230-500-225A1 Power Meter PM800 Series 6/2006 Table of Contents Scaling Alarm Setpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 Alarm Conditions and Alarm Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 CHAPTER 7—ADVANCED ALARMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Alarm Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Advanced Alarm Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Alarm Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 Viewing Alarm Activity and History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Alarm Conditions and Alarm Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 CHAPTER 8—LOGGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Memory Allocation for Log Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Alarm Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Alarm Log Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Maintenance Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Data Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Alarm-driven Data Log Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Organizing Data Log Files (PM850, PM870) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Billing Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 Configure the Billing Log Logging Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 CHAPTER 9—WAVEFORM CAPTURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Waveform Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 Initiating a Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 Waveform Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 Waveform Storage Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 How the Power Meter Captures an Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 Channel Selection in SMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 CHAPTER 10—DISTURBANCE MONITORING (PM870) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 About Disturbance Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 Capabilities of the PM870 During an Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Using the Power Meter with SMS to Perform Disturbance Monitoring . . . . . . . . . . . . . . . . 114 CHAPTER 11—MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . 115 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Power Meter Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Identifying the Firmware Version, Model, and Serial Number . . . . . . . . . . . . . . . . . . . . . . . 116 Viewing the Display in Different Languages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 Heartbeat LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 APPENDIX A—POWER METER REGISTER LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 About Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Floating-point Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 How Power Factor is Stored in the Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 How Date and Time are Stored in Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Register List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 © 2006 Schneider Electric All Rights Reserved v Power Meter PM800 Series 63230-500-225A1 Table of Contents 6/2006 APPENDIX B—USING THE COMMAND INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 Overview of the Command Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 Issuing Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 I/O Point Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 Operating Outputs from the Command Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212 Using the Command Interface to Change Configuration Registers . . . . . . . . . . . . . . . . . . 213 Conditional Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 Command Interface Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 Digital Input Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 Incremental Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 Using Incremental Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 Setting Up Individual Harmonic Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218 Changing Scale Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219 Enabling Floating-point Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 APPENDIX C—EN50160 EVALUATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 How Results of the Evaluations Are Reported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 Possible Configurations Through Register Writes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 Evaluation During Normal Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 Power Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 Supply Voltage Variations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Supply Voltage Unbalance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Harmonic Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Evaluations During Abnormal Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 Count of Magnitude of Rapid Voltage Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 Detection and Classification of Supply Voltage Dips . . . . . . . . . . . . . . . . . . . . . . . . . . 227 Detection of Interruptions of the Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Detecting and Classifying Temporary Power Frequency Overvoltages . . . . . . . . . . . . 228 Operation with EN50160 Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 Resetting Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 Alarms Allocated for Evaluations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 Harmonic Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 Time Intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 EN50160 Evaluation System Configuration and Status Registers . . . . . . . . . . . . . . . . . . . 231 Evaluation Data Available Over a Communications Link . . . . . . . . . . . . . . . . . . . . . . . . . . 233 Portal Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233 Setting Up EN50160 Evaluation from the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241 APPENDIX D—GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243 Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243 Abbreviations and Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249 © 2006 Schneider Electric All Rights Reserved vi ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 1—Introduction CHAPTER 1—INTRODUCTION About This Manual This reference manual explains how to operate and configure a ® PowerLogic Series 800 Power Meter. Unless otherwise noted, the information contained in this manual refers to the following Power Meters: Power Meter with integrated display Power Meter without a display Power Meter with a remote display. Refer to “Power Meter Parts and Accessories” on page 7 for all models and model numbers. For a list of supported features, see “Features” on page 9. © 2006 Schneider Electric. All Rights Reserved. 1 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 1—Introduction 6/2006 Topics Not Covered in This Manual Some of the power meter’s advanced features, such as onboard data logs and alarm log files, can only be set up over the communications TM link using System Manager Software (SMS) from PowerLogic. This power meter instruction bulletin describes these advanced features, but does not explain how to set them up. For instructions on using SMS, refer to the SMS online help and the SMS setup guide, which is available in English, French, and Spanish. See Table 1–1 for a list of power meter models supported by SMS. Table 1–1: Power Meter Models Supported By SMS SMS Type SMS Version PM820 PM850 PM870 SMS121 3.3.2.2 or higher 99 — SMS1500 3.3.2.2 or higher 99 — SMS3000 3.3.2.2 or higher 99 — 4.0 or 4.0 with Service Update 1 99 — SMSDL 4.0 with Service Update 2 or higher 99 9 4.0 or 4.0 with Service Update 1 99 — SMSSE 4.0 with Service Update 2 or higher 99 9 4.0 or 4.0 with Service Update 1 99 — SMSPE 4.0 with Service Update 2 or higher 99 9 © 2006 Schneider Electric. All Rights Reserved. 2 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 1—Introduction What is the Power Meter? The power meter is a multifunction, digital instrumentation, data acquisition and control device. It can replace a variety of meters, relays, transducers and other components. The power meter can be installed at multiple locations within a facility. The power meter is equipped with RS485 communications for integration into any power monitoring and control system. However, System Manager™ software (SMS) from PowerLogic, which is written specifically for power monitoring and control, best supports the power meter’s advanced features. The power meter is a true rms meter capable of exceptionally accurate measurement of highly nonlinear loads. A sophisticated sampling technique enables accurate, true rms measurement through the 63rd harmonic. You can view over 50 metered values plus minimum and maximum data from the display or remotely using software. Table 1–2 summarizes the readings available from the power meter. Table 1–2: Summary of power meter Instrumentation Real-time Readings Power Analysis Current (per phase, residual, 3-Phase)Displacement Power Factor (per phase, 3-Phase ) Voltage (L–L, L–N, 3-Phase)Fundamental Voltages (per phase) Real Power (per phase, 3-Phase )Fundamental Currents (per phase) Reactive Power (per phase, 3-Phase )Fundamental Real Power (per phase) Apparent Power (per phase, 3-Phase )Fundamental Reactive Power (per phase) Power Factor (per phase, 3-Phase )Unbalance (current and voltage) FrequencyPhase Rotation THD (current and voltage)Current and Voltage Harmonic Magnitudes & Angles (per phase) Sequence Components Energy Readings Demand Readings Accumulated Energy, RealDemand Current (per phase present, 3-Phase Accumulated Energy, Reactive avg.) Accumulated Energy, Apparent Average Power Factor (3-Phase total) Bidirectional Readings Demand Real Power (per phase present, peak) Reactive Energy by QuadrantDemand Reactive Power (per phase present, Incremental Energy peak) Conditional EnergyDemand Apparent Power (per phase present, peak) Coincident Readings Predicted Power Demands © 2006 Schneider Electric. All Rights Reserved. 3 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 1—Introduction 6/2006 Power Meter Hardware Power Meter With Integrated Display Figure 1–1: Parts of the Series 800 Power Meter with integrated display Bottom View 2 4 3 1 5 6 8 7 Back View Table 1–3: Parts of the Series 800 Power Meter With Integrated Display No. Part Description 1 Control power supply connector Connection for control power to the power meter. 2 Voltage inputs Voltage metering connections. 3 I/O connector KY pulse output/digital input connections 4 Heartbeat LED A green flashing LED indicates the power meter is ON. The RS-485 port is used for communications with a monitoring and 5 RS-485 port (COM1) control system. This port can be daisy-chained to multiple devices. 6 Option module connector Used to connect an option module to the power meter. 7 Current inputs Current metering connections. 8 Integrated display Visual interface to configure and operate the power meter. © 2006 Schneider Electric. All Rights Reserved. 4 PLSD110042 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 1—Introduction Power Meter Without Display Figure 1–2: Parts of the Series 800 Power Meter without display Bottom View 3 4 2 1 5 6 7 Back View Table 1–4: Parts of the Series 800 Power Meter Without Display No. Part Description 1 Control power supply connector Connection for control power to the power meter. 2 Voltage inputs Voltage metering connections. 3 I/O connector KY pulse output/digital input connections 4 Heartbeat LED A green flashing LED indicates the power meter is ON. The RS-485 port is used for communications with a monitoring and 5 RS-485 port (COM1) control system. This port can be daisy-chained to multiple devices. 6 Option module connector Used to connect an option module to the power meter. 7 Current inputs Current metering connections. © 2006 Schneider Electric. All Rights Reserved. 5 PLSD110317 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 1—Introduction 6/2006 Power Meter With Remote Display NOTE: The remote display kit (PM8RD) is used with a power meter without a display. See “Power Meter Without Display” on page 5 for the parts of the power meter without a display. Figure 1–3: Parts of the remote display and the remote display adapter 1 2 4 5 6 7 8 3 TX/RX PM8RDA Top View Table 1–5: Parts of the Remote Display No. Part Description Provides the connection between the remote display and the 1 Remote display adapter (PM8RDA) power meter. Also provides an additional RS232/RS485 connection (2- or 4-wire). 2 Cable CAB12 Connects the remote display to the remote display adapter. 3 Remote display (PM8D) Visual interface to configure and operate the power meter. 4 Communications mode button Use to select the communications mode (RS232 or RS485). When lit the LED indicates the communications port is in RS232 5 Communications mode LED mode. The RS485 port is used for communications with a monitoring and 6 RS232/RS485 port control system. This port can be daisy-chained to multiple devices. 7 Tx/Rx Activity LED The LED flashes to indicate communications activity. Port for the CAB12 cable used to connect the remote display to 8 CAB12 port the remote display adapter. © 2006 Schneider Electric. All Rights Reserved. 6 PLSD110318 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 1—Introduction Power Meter Parts and Accessories Table 1–6: Power Meter Parts and Accessories Model Number Description Square D Merlin Gerin Power Meters ➀ ➀ PM820 PM820MG ➁ ➁ Power Meter with Integrated Display PM850 PM850MG ➂ ➂ PM870 PM870MG ➀ ➀ PM820U PM820UMG ➁ ➁ Power Meter without Display PM850U PM850UMG ➂ ➂ PM870U PM870UMG ➀ ➀ PM820RD PM820RDMG ➁ ➁ Power Meter with Remote Display PM850RD PM850RDMG ➂ ➂ PM870RD PM870RDMG Accessories Remote Display with Remote Display PM8RD PM8RDMG Adapter Remote Display Adapter PM8RDA Input/Output Modules PM8M22, PM8M26, PM8M2222 Cable (12 inch) Extender Kit for RJ11EXT displays Retrofit Gasket (for 4 in. round hole PM8G mounting) CM2000 Retrofit Mounting Adapter PM8MA ➀ The Power Meter units for these models are identical and support the same features (see “Features” on page 9). ➁ The Power Meter units for these models are identical and support the same features (see “Features” on page 9). ➂ The Power Meter units for these models are identical and support the same features (see “Features” on page 9). © 2006 Schneider Electric. All Rights Reserved. 7 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 1—Introduction 6/2006 Box Contents Table 1–7: Box contents based on model Model Description Box Contents Power Meter with integrated display Hardware kit (63230-500-16) containing: — Two retainer clips — Template — Install sheet Power Meter with Integrated Display —Lugs — Plug set — Terminator MCT2W Power Meter installation manual Power Meter without display Hardware kit (63230-500-42) containing: — Two retainer clips — Template — Install sheet Power Meter without Display —Lugs — DIN Slide — Plug set — Terminator MCT2W Power Meter installation manual Power Meter without display Remote display (PM8D) Remote display adapter (PM8RDA) Hardware kit (63230-500-42) containing: — Two retainer clips — Template — Install sheet —Lugs Power Meter with Remote Display — DIN Slide — Plug set — Terminator MCT2W Hardware kit (63230-500-96) containing: — Communication cable (CAB12) — Mounting screws Power Meter installation manual © 2006 Schneider Electric. All Rights Reserved. 8 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 1—Introduction Features Table 1–8: Series 800 Power Meter Features PM820 PM850 PM870 True rms metering to the 63rd harmonic 99 9 Accepts standard CT and PT inputs 99 9 600 volt direct connection on voltage inputs 99 9 High accuracy — 0.075% current and voltage (typical conditions) 99 9 Min/max readings of metered data 99 9 Input metering (five channels) with PM8M22, PM8M26, or PM8M2222 99 9 installed Power quality readings — THD 99 9 Downloadable firmware 99 9 Easy setup through the integrated or remote display (password protected) 99 9 Setpoint-controlled alarm and relay functions 99 9 Onboard alarm logging 99 9 Wide operating temperature range: –25° to +70°C for the power meter 99 9 unit Communications: 9 9 9 Onboard: one Modbus RS485 (2-wire) PM8RD: one configurable Modbus RS232/RS485 (2- or 4-wire) 9 9 9 Active energy accuracy: IEC 62053-22 and ANSI C12.20 Class 0.5S 99 9 Nonvolatile clock 99 9 Onboard data logging 80 KB 800 KB 800 KB Real-time harmonic magnitudes and angles (I and V): — — To the 31st harmonic 9 To the 63rd harmonic 9 9 — Waveform capture 9 Standard — 9 Advanced — — 9 EN50160 evaluations NOTE: The PM850 performs EN50160 evaluations — 99 based on standard alarms, while the PM870 performs EN50160 evaluations based on disturbance alarms. Current and voltage sag/swell detection and logging — — 9 © 2006 Schneider Electric. All Rights Reserved. 9 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 1—Introduction 6/2006 Firmware This instruction bulletin is written to be used with firmware version 10.5x. See “Identifying the Firmware Version, Model, and Serial Number” on page 116 for instructions on how to determine the firmware version. To download the latest firmware version, follow the steps below: 1. Using a web browser, go to http://www.powerlogic.com. 2. Select United States. 3. Click downloads. 4. Enter your login information, then click LogIn. 5. Click PM8 Firmware under the POWERLOGIC section. 6. Follow the instructions on the web page that explains how to download and install the new firmware. © 2006 Schneider Electric. All Rights Reserved. 10 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 2—Safety Precautions CHAPTER 2—SAFETY PRECAUTIONS DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH Apply appropriat e personal protective equipment (PPE) and follow safe electrical practices. For example, in the United States, see NFPA 70E. This equipment must only be installed and serviced by qualified electrical personnel. NEVER work alone. Before performing visual inspections, te sts, or maintenance on this equipment, disconnect all sources of electric power. Assume that all circuits are live until they have been completely de-energized, tested, and tagged. Pay particular attention to the design of the power system. Consider all sources of power, including the possibility of backfeeding. Turn off all power supplying this equipment before working on or inside equipment. Always use a properly rated voltage sensing device to confirm that all power is off. Beware of potential hazards and carefully inspect the work area for tools and objects that may have been left inside the equipment. Use caution while removing or installing panels so that they do not extend into the energized bus; avoid handling the panels, which could cause personal injury. The successful operation of this equipment depends upon proper handling, installation, and operation. Neglecting fundamental installation requirements may lead to personal injury as well as damage to electrical equipment or other property. Before performing Dielectric (Hi-Pot) or Megger testing on any equipment in which the power meter is installed, disconnect all input and output wires to the power meter. High voltage testing may damage electronic components contained in the power meter. Failure to follow this instruction will result in death or serious injury. © 2006 Schneider Electric. All Rights Reserved. 11 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 2—Safety Precautions 6/2006 © 2006 Schneider Electric. All Rights Reserved. 12 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 3—Operation CHAPTER 3—OPERATION This section explains how to use a display with a power meter. For a list of all power meter models using an integrated display or a remote display, see Table 1–6 on page 7. Operating the Display The power meter is equipped with a large, back-lit LCD display. It can display up to five lines of information plus a sixth row of menu options. Figure 3–1 shows the different parts of the power meter. Figure 3–1: Power Meter Display A. Type of measurement AB CD B. Screen Title C. Alarm indicator �������������� ��� � D. Maintenance icon ����������� E �������������� E. Bar Chart (%) � ��� �� F F. Units M ����������� �������������� � ��� �� G. Display more menu items ����������� H. Menu item �������������� � ��� � I. Selected menu indicator � L � ��� � J. Button ��� ����� ������ ���� K. Return to previous menu L. Values G M. Phase K J I H © 2006 Schneider Electric. All Rights Reserved. 13 PLSD110097 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 3—Operation 6/2006 How the Buttons Work The buttons are used to select menu items, display more menu items in a menu list, and return to previous menus. A menu item appears over one of the four buttons. Pressing a button selects the menu item and displays the menu item’s screen. When you have reached the highest menu level, a black triangle appears beneath the selected menu item. To return to the previous menu level, press the button below 1;. To cycle through the menu items in a menu list, press the button below ###: (see Figure 3–1). NOTE: Each time you read “press” in this manual, press and release the appropriate button beneath the menu item. For example, if you are asked to “Press PHASE,” you would press the button below the PHASE menu item. Changing Values When a value is selected, it flashes to indicate that it can be modified. A value is changed by doing the following: Press + or – to change numbers or scroll through available options. If you are entering more than one number, press <-- to move to the next number in the sequence. To save your changes and move to the next field, press OK. Menu Overview The figures below show the menu items of the first two levels of the power meter. Level 1 contains all of the menu items available on the first screen of the power meter. Selecting a Level 1 menu item takes you to the next screen level containing the Level 2 menu items. NOTE: The ###: is used to scroll through all menu items on a level. © 2006 Schneider Electric. All Rights Reserved. 14 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 3—Operation Figure 3–2: Abbreviated List of PM820(RD), PM850(RD), and PM870(RD) Menu Items LEVEL 1 LEVEL 2 AMPS (I) PHASE DMD UNBAL VOLTS (U-V) V L-L V L-N PWR (PQS) PWR PHASE DMD ENERG (E) WH VAH VARH INC PF TRUE DISPL HZ (F) THD V L-L (U) V L-N (V) I MINMX MINMX AMPS (I) VOLTS (U-V) UNBAL PWR (PQS) PF HZ (F) THD V THD I HARM V L-L (U) V L-N (V) I ALARM ACTIV HIST I/O D OUT D IN A OUT A IN PM8M2222 TIMER 1 CONTR 2 MAINT RESET METER ENERG (E) DMD MINMX MODE TIMER SETUP DATE TIME LANG COMMS (COM) METER ALARM I/O PASSW TIMER ADVAN COMM1 DIAGN. METER REG CLOCK D OUT [Digital KY Out] PM8RD COMM2 D IN [Digital In] PM8M2222, PM8M26, and PM8M22 PM8M2222 A OUT [Analog Out] A IN [Analog In] ➀ Available with some models. ➁ IEC is the default for Merlin Gerin branded power meters, and IEEE is the default mode for Square D branded power meters. © 2006 Schneider Electric. All Rights Reserved. 15 PLSD110078 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 3—Operation 6/2006 Set Up the Power Meter This section explains how to setup a Power Meter using a display. To configure a Power Meter without a display use System Manager Software (SMS). NOTE: If you are setting up the Power Meter using SMS, it is recommended you set up communications first. The default settings are 1) Protocol: Modbus RTU, 2) Address: 1, 3) Baud rate: 9600, and 4) Parity: Even. To begin power meter setup, do the following: 1. Scroll through the Level 1 menu list until you see MAINT. 2. Press MAINT. 3. Press SETUP. 4. Enter your password. NOTE: The default password is 0000. 5. To save the changes, press1; until the SAVE CHANGES? prompt appears, then press YES. Follow the directions in the following sections to set up the meter. © 2006 Schneider Electric. All Rights Reserved. 16 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 3—Operation Power Meter With Integrated Display Communications Setup Table 3–1: Communications Default Settings Communications Setting Default Protocol MB.RTU (Modbus RTU) Address 1 Baud Rate 9600 Parity Even 1. Press ###: until COMMS (communications) is visible. ����������� 2. Press COMMS (communications). 3. Select the protocol: MB.RTU (Modbus ������ RTU), Jbus, MB. A.8 (Modbus ASCII 8 bits), MB. A.7 (Modbus ASCII 7 bits). ��� ����� 4. Press OK. ����� !"#� 5. Enter the ADDR (power meter address). 6. Press OK. �$�% �� �� � � 7. Select the BAUD (baud rate). 8. Press OK. 9. Select the parity: EVEN, ODD, or NONE. 10. Press OK. 11. Press1; until you are asked to save your changes. 12. Press YES to save the changes. © 2006 Schneider Electric. All Rights Reserved. 17 PLSD110100 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 3—Operation 6/2006 Power Meter With Remote Display Communications Setup Comm1 Setup 1. Press ###: until COMMS (communications) is visible. ������������ 2. Press COMM1 (communications). 3. Select the protocol: MB.RTU (Modbus ������ RTU), Jbus, MB. A.8 (Modbus ASCII 8 bits), MB. A.7 (Modbus ASCII 7 bits). ��� ����� 4. Press OK. ����� !"#� 5. Enter the ADDR (power meter address). �$�% 6. Press OK. �� �� � � 7. Select the BAUD (baud rate). 8. Press OK. 9. Select the parity: EVEN, ODD, or NONE. 10. Press OK. 11. Press1; until you are asked to save your changes. 12. Press YES to save the changes. Comm2 Setup 1. Press ###: until COMMS (communications) is visible. �����&������ 2. Press COMM2 (communications). 3. Select the protocol: MB.RTU (Modbus ��� ������ RTU), Jbus, MB. A.8 (Modbus ASCII 8 �� bits), MB. A.7 (Modbus ASCII 7 bits). ����� 4. Press OK. ���� !"#� 5. Enter the ADDR (power meter address). �’�� 6. Press OK. �� �� � � 7. Select the BAUD (baud rate). 8. Press OK. 9. Select the parity: EVEN, ODD, or NONE. 10. Press OK. 11. Press1; until you are asked to save your changes. 12. Press YES to save the changes. © 2006 Schneider Electric. All Rights Reserved. 18 PLSD110321 PLSD110273 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 3—Operation Set Up the Date 1. Press ###: until DATE is visible. 2. Press DATE. ���������� 3. Enter the MONTH number. �� ����� 4. Press OK. 5. Enter the DAY number. �� ��( 6. Press OK. ���� 7. Enter the YEAR number. (��� 8. Press OK. �������� �)�)( 9. Select how the date is displayed: M/D/Y, �� �� � � Y/M/D, or D/M/Y). 10. Press 1; to return to the SETUP MODE screen. 11. To verify the new settings, press MAINT > DIAGN > CLOCK. NOTE: Set Up the Time 1. Press ###: until TIME is visible. 2. Press TIME. ���������� 3. Enter the HOUR. �� 4. Press OK. �$#, 5. Enter the MIN (minutes). �� ��� 6. Press OK. �� 7. Enter the SEC (seconds). �%* 8. Press OK. &+� 9. Select how the time is displayed: 24H or �� �� � � AM/PM. 10. Press 1; to return to the SETUP MODE screen. 11. To verify the new settings, press MAINT > DIAGN > CLOCK. NOTE: © 2006 Schneider Electric. All Rights Reserved. 19 PLSD110227 PLSD110218 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 3—Operation 6/2006 Set Up the Language 1. Press ###: until LANG is visible. 2. Press LANG. -��.��.� 3. Select the language: ENGL (English), SPAN (Spanish), FREN (French), ��.-� GERMN (German), or RUSSN (Russian). 4. Press OK. 5. Press1; until you are asked to save your changes. 6. Press YES to save the changes. �� �� � � Set Up CTs 1. Press ###: until METER is visible. 2. Press METER. �������� 3. Press CT. 4. Enter the PRIM (primary CT) number. 5. Press OK. ��� ��� ���� 6. Enter the SEC. (secondary CT) number. ��� � 7. Press OK. ���� 8. Press1; until you are asked to save your changes. �� �� � � 9. Press YES to save the changes. © 2006 Schneider Electric. All Rights Reserved. 20 PLSD110103 PLSD110106 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 3—Operation Set Up PTs 1. Press ###: until METER is visible. 2. Press METER. �������� 3. Press PT. / � ���-� 4. Enter the SCALE value: x1, x10, x100, NO PT (for direct connect). ���� ��� 5. Press OK. 6. Enter the PRIM (primary) value. ���� ��� 7. Press OK. 8. Enter the SEC. (secondary) value. �� �� � � 9. Press OK. 10. Press1; until you are asked to save your changes. 11. Press YES to save the changes. Set Up Frequency 1. Press ###: until METER is visible. 2. Press METER. �(�����0,%1#%�*2���� 3. Press ###: until HZ is visible. 4. Press HZ. 5. Select the frequency. �� �3 6. Press OK. �� 0��4� 7. Press1; until you are asked to save your changes. 8. Press YES to save the changes. �� �� � � © 2006 Schneider Electric. All Rights Reserved. 21 PLSD110112 PLSD110109 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 3—Operation 6/2006 Set Up the Meter System Type 1. Press ###: until METER is visible. 2. Press METER. 5��������(�������� 3. Press ###: until SYS is visible. A � 4. Press SYS. 6��� 5. Select your system type based on the (A) B � �� number of wires, (B) number of CTs, (C) C the number of voltage connections (either � �� direct connect or with PT), and (D) the D SMS system type. �� �(�� 6. Press OK. �� � � � 7. Press1; until you are asked to save your changes. 8. Press YES to save the changes. © 2006 Schneider Electric. All Rights Reserved. 22 PLSD110324 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 3—Operation Set Up Alarms 1. Press ###: until ALARM is visible. 2. Press ALARM. �’���’�� ���� 3. Press <- or -> to select the alarm you want to edit. ����-� 4. Press EDIT. ��� ��.� 5. Select to enable or disable the alarm: ENABL (enable) or DISAB (disable). ����- 6. Press OK. 7. Select the PR (priority): NONE, HIGH, �� �� � � MED, or LOW. 8. Press OK. 9. Select how the alarm values are displayed: ABSOL (absolute value) or RELAT (percentage relative to the running average). 10. Enter the PU VALUE (pick-up value). 11. Press OK. �’���’�� ���� 12. Enter the PU DELAY (pick-up delay). 13. Press OK. ��� ��.� ��� 14. Enter the DO VALUE (drop-out value). ��� � ��-�( 15. Press OK. ��� 16. Enter the DO DELAY (drop-out delay). � ��.� 17. Press OK. ��� ��-�( � 18. Press 1; to return to the alarm summary �� ����� � � screen. 19. Press 1; to return to the SETUP screen. © 2006 Schneider Electric. All Rights Reserved. 23 PLSD110311 PLSD110212 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 3—Operation 6/2006 Set Up I/Os 1. Press ###: until I/O is visible. 2. Press I/O. ( ���� 3. Press D OUT for digital output or D IN for digital input, or press A OUT for analog ���� output or A IN for analog input. Use the ###: button to scroll through these � ��-�� selections. � ����� NOTE: Analog inputs and outputs are available only with the PM8222 option �/�� module. �� �� � � 4. Press EDIT. 5. Select the I/O mode based on the I/O type and the user selected mode: NORM., LATCH, TIMED, PULSE, or END OF. 6. Depending on the mode selected, the power meter will prompt you to enter the pulse weight, timer, and control. 7. Press OK. 8. Select EXT. (externally controlled via communications) or ALARM (controlled by an alarm). 9. Press1; until you are asked to save your changes. 10. Press YES to save the changes. © 2006 Schneider Electric. All Rights Reserved. 24 PLSD110221 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 3—Operation Set Up the Passwords 1. Press ###: until PASSW (password) is visible. ����6������������� 2. Press PASSW. ���� 3. Enter the SETUP password. ����� 4. Press OK. ���� ���.� 5. Enter the DIAG (diagnostics) password. 6. Press OK. ���� ����. 7. Enter the ENERG (energy reset) ���� ��)�/ password. �� �� � � 8. Press OK. 9. Enter the MN/MX (minimum/maximum reset) password. 10. Press OK. 11. Press1; until you are asked to save your changes. 12. Press YES to save the changes. Set Up the Operating Time Threshold 1. Press ###: until TIMER is visible. 2. Press TIMER. ��������������� � 3. Enter the 3-phase current average. NOTE: The power meter begins counting 5�� ����’. the operating time whenever the readings � are equal to or above the average. � 4. Press OK. 5. Press1; until you are asked to save your changes. �� ����� � � 6. Press YES to save the changes. © 2006 Schneider Electric. All Rights Reserved. 25 PLSD110257 PLSD110224 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 3—Operation 6/2006 Advanced Power Meter Setup Options To setup the advanced power meter options, do the following: 1. Scroll through the Level 1 menu list until you see MAINT. 2. Press MAINT. 3. Press SETUP. 4. Enter your password. NOTE: The default password is 0000. 5. Press ###: until ADVAN (advanced setup) is visible. 6. Press ADVAN. Follow the directions in the following sections to set up the meter. Set Up the Phase Rotation 1. Press ###: until ROT (phase rotation) is visible. �������$7"78$� 2. Press ROT. 3. Select the phase rotation: ABC or CBA. ��� 4. Press OK. 5. Press1; until you are asked to save your changes. 6. Press YES to save the changes. �� �� � © 2006 Schneider Electric. All Rights Reserved. 26 PLSD110203 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 3—Operation Set Up the Incremental Energy Interval 1. Press ###: until E-INC is visible. 2. Press E-INC (incremental energy). ���������.( 3. Enter the INTVL (interval). Range is 00 to 1440. 4. Press OK. �� ���’- 5. Press1; until you are asked to save your changes. 6. Press YES to save the changes. �� �� � � Set Up the THD Calculation 1. Press ###: until THD is visible. 2. Press THD. �����"9*#9"78$� 3. Select the THD calculation: FUND or RMS. 4. Press OK. :#�� 5. Press1; until you are asked to save your changes. 6. Press YES to save the changes. �� �� � © 2006 Schneider Electric. All Rights Reserved. 27 PLSD110206 PLSD110197 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 3—Operation 6/2006 Set Up the VAR/PF Convention 1. Press ###: until PF is visible. 2. Press PF. �0��$�;%�78$� 3. Select the Var/PF convention: IEEE or IEC. 4. Press OK. 8%%% 5. Press1; until you are asked to save your changes. 6. Press YES to save the changes. �� �� � Set Up the Lock Resets 1. Press ###: until LOCK is visible. 2. Press LOCK. 9$*<��%=%7=> 3. Select Y (yes) or N (no) to enable or disable resets for PK.DMD, ENERG, � � ���� MN/MX, and METER. ( ����. 4. Press OK. 5. Press1; until you are asked to save your � �?)@A changes. � � �%7%, 6. Press YES to save the changes. �� ��� � � © 2006 Schneider Electric. All Rights Reserved. 28 PLSD110200 PLSD110209 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 3—Operation Set Up the Alarm Backlight 1. Press ###: until BLINK is visible. 2. Press BLINK. �-������� -�.��> 3. Enter ON or OFF. 4. Press OK. 5. Press1; until you are asked to save your �� changes. 6. Press YES to save the changes. �� �� � � Set Up the Bar Graph 1. Press ###: until BARGR is visible. 2. Press BARGR. �",�B,"C��=*"9% 3. Press AMPS or PWR. 4. Select AUTO or MAN. If MAN is selected, press OK and enter the %CT*PT and KW (for PWR) or the %CT and A (for AMPS). 5. Press OK. 6. Press1; until you are asked to save your changes. �� ���� �6� 7. Press YES to save the changes. © 2006 Schneider Electric. All Rights Reserved. 29 PLSD110231 PLSD110215 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 3—Operation 6/2006 Set Up the Power Demand Configuration 1. Press ###: until DMD is visible. 2. Press DMD. �$D%,��������0�. � 3. Select the demand configuration. Choices are COMMS, RCOMM, CLOCK, RCLCK, ��-� IENGY, THERM, SLIDE, BLOCK, RBLCK, INPUT, and RINPUT. �� ���’- 4. Press OK. � ����� 5. Enter the INTVL (interval) and press OK. 6. Enter the SUB-I (sub-interval) and press OK. �� �� � � 7. Press1; until you are asked to save your changes. 8. Press YES to save the changes. Set Up the EN50160 Evaluation 1. Press ###: until 50160 is visible. 2. Press 50160. �����E������� 3. Select ON. 4. Press OK. �� 5. Change the nominal voltage (NOM V) ����’ ��� value if desired (230 is the default). 6. Press OK to return to the SETUP MODE screen. 7. Press 1; until you are prompted to save � �� ����� � your changes. 8. Press YES to save your changes and reset the power meter. © 2006 Schneider Electric. All Rights Reserved. 30 PLSD110316 PLSD110232 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 3—Operation Power Meter Resets To access the reset options of the power meter, do the following: 1. Scroll through the Level 1 menu list until you see MAINT (maintenance). 2. Press MAINT. 3. Press RESET. 4. Continue by following the instructions in the sections below. Initialize the Power Meter Initializing the power meter resets the energy readings, minimum/maximum values, and ������������> operating times. Do the following to initialize the power meter: 1. Press ###: until METER is visible. 2. Press METER. 3. Enter the password (the default is 0000). 4. Press YES to initialize the power meter and to return to the RESET MODE screen. �� (�� NOTE: We recommend initializing the power meter after you make changes to any of the following: CTs, PTs, frequency, or system type. © 2006 Schneider Electric. All Rights Reserved. 31 PLSD110285 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 3—Operation 6/2006 Reset the Accumulated Energy Readings 1. Press ###: until ENERG is visible. 2. Press ENERG. ����������.(�> 3. Enter the password (the default is 0000). ������ 4. Press YES to reset the accumulated <6F energy readings and to return to the ������ <’��F RESET MODE screen. ������ <’�F �������� ������ �� (�� Reset the Accumulated Demand Readings 1. Press ###: until DMD is visible. 2. Press DMD. �������������> 3. Enter the password (the default is 0000). � �< <6G 4. Press YES to reset the accumulated demand readings and to return to the � �< <’��G RESET MODE screen. �� �< ����� �������� ����� �� (�� © 2006 Schneider Electric. All Rights Reserved. 32 PLSD110281 PLSD110280 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 3—Operation Reset the Minimum/Maximum Values 1. Press ###: until MINMX is visible. 2. Press MINMX. ���������)��/�> 3. Enter the password (the default is 0000). 4. Press YES to reset the minimum/maximum values and to return to the RESET MODE screen. �������� ������ �� (�� Change the Mode 1. Press ###: until MODE is visible. 2. Press MODE. ��������0��-��> 3. Press IEEE (default for Square D branded power meters) or IEC (default for Merlin Gerin branded power meters) depending on the operating mode you want to use. NOTE: Resetting the mode changes the menu labels, power factor conventions, and THD calculations to match the standard mode selected. To customize the mode changes, 4��� ���� ��� see the register list. © 2006 Schneider Electric. All Rights Reserved. 33 PLSD110283 PLSD110282 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 3—Operation 6/2006 Reset the Accumulated Operating Time 1. Press ###: until TIMER is visible. 2. Press TIMER. ����������������> 3. Enter the password (the default is 0000). ��� 4. Press YES to reset the accumulated ��(� operating time and to return to the RESET �� ����� MODE screen. NOTE: The accumulated days, hours, and �� ���� minutes of operation are reset to zero when YES is pressed. �� (�� © 2006 Schneider Electric. All Rights Reserved. 34 PLSD110284 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 3—Operation Power Meter Diagnostics To begin viewing the power meter’s model, firmware version, serial number, read and write registers, or check the health status, do the following: 1. Scroll through the Level 1 menu list until you see MAINT (maintenance). 2. Press MAINT. 3. Press DIAG (diagnostics) to open the HEALTH STATUS screen. 4. Continue by following the instructions in the sections below. View the Meter Information 1. On the HEALTH STATUS screen, press METER (meter information). ��������0� 2. View the meter information. 3. Press --> to view more meter information. ��� ��� ����- 4. Press 1; to return to the HEALTH ��’ ������ ���� STATUS screen. ��’ ������ ����� �������� ���� �� �� �H © 2006 Schneider Electric. All Rights Reserved. 35 PLSD110094c ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 3—Operation 6/2006 Check the Health Status 1. Press MAINT. (maintenance). 2. Press DIAG. The health status is ���-��������� displayed on the screen. 3. Press 1; to return to the MAINTENANCE screen. NOTE: The wrench icon and the health status code displays when a health problem is detected. For code 1, set up the Date/Time (see “Set Up the Date” and “Set Up the Time” � on page 19). For other codes, contact �� ����� ��.� �-�� technical support. Read and Write Registers 1. On the HEALTH STATUS screen, Press REG (register). �)6���.����� 2. Enter the password (the default is 0000). 3. Enter the REG. (register) number. ���� ��.� The HEX (hexadecimal) and DEC ����� (decimal) values of the register number ��/ you entered displays. � ��� 4. Press OK. 5. Enter the DEC number if necessary. �� �� � � 6. Press 1; to return to the DIAGNOSTICS screen. NOTE: For more information about using registers, see Appendix A—Power Meter Register List on page 121. © 2006 Schneider Electric. All Rights Reserved. 36 PLSD110194 PLSD110191 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 3—Operation View the Meter Date and TIme 1. On the HEALTH STATUS screen, press CLOCK (current date and time). ��I���������� 2. View the date and time. 3. Press 1; to return to the HEALTH �� ��� ���� STATUS screen. ��’ �� ��� ��’ � ��� �������� ���� �� �� �H © 2006 Schneider Electric. All Rights Reserved. 37 PLSD110327 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 3—Operation 6/2006 © 2006 Schneider Electric. All Rights Reserved. 38 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 4—Metering Capabilities CHAPTER 4—CHAPTER 4—METERING CAPABILITIES Real-Time Readings The power meter measures currents and voltages and reports in real time the rms values for all three phases and neutral. In addition, the power meter calculates power factor, real power, reactive power, and more. Table 4–1 lists some of the real-time readings that are updated every second along with their reportable ranges. Table 4–1: One-second, Real-time Readings Real-time Readings Reportable Range Current Per-Phase 0 to 32,767 A Neutral 0 to 32,767 A 3-Phase Average 0 to 32,767 A % Unbalance 0 to 100.0% Voltage Line-to-Line, Per-Phase 0 to 1,200 kV Line-to-Line, 3-Phase Average 0 to 1,200 kV Line-to-Neutral, Per-Phase 0 to 1,200 kV Line-to-Neutral, 3-Phase Average 0 to 1,200 kV % Unbalance 0 to 100.0% Real Power Per-Phase 0 to ± 3,276.70 MW 3-Phase Total 0 to ± 3,276.70 MW Reactive Power Per-Phase 0 to ± 3,276.70 MVAR 3-Phase Total 0 to ± 3,276.70 MVAR Apparent Power Per-Phase 0 to ± 3,276.70 MVA 3-Phase Total 0 to ± 3,276.70 MVA Power Factor (True) Per-Phase –0.002 to 1.000 to +0.002 3-Phase Total –0.002 to 1.000 to +0.002 Power Factor (Displacement) Per-Phase –0.002 to 1.000 to +0.002 3-Phase Total –0.002 to 1.000 to +0.002 Frequency 45–65 Hz 23.00 to 67.00 Hz 350–450 Hz 350.00 to 450.00 Hz © 2006 Schneider Electric. All Rights Reserved. 39 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 4—Metering Capabilities 6/2006 Min/Max Values for Real-time Readings When certain one-second real-time readings reach their highest or lowest value, the Power Meter saves the values in its nonvolatile memory. These values are called the minimum and maximum (min/max) values. The Power Meter stores the min/max values for the current month and previous month. After the end of each month, the Power Meter moves the current month’s min/max values into the previous month’s register space and resets the current month’s min/max values. The current month’s min/max values can be reset manually at any time using the Power Meter display or SMS. After the min/max values are reset, the Power Meter records the date and time. The real-time readings evaluated are: Min/Max Voltage L-L Min/Max Voltage L-N Min/Max Current Min/Max Voltage L-L, Unbalance Min/Max Voltage L-N, Unbalance Min/Max Total True Power Factor Min/Max Total Displacement Power Factor Min/Max Real Power Total Min/Max Reactive Power Total Min/Max Apparent Power Total Min/Max THD/thd Voltage L-L Min/Max THD/thd Voltage L-N Min/Max THD/thd Current Min/Max Frequency Min/Max Voltage N-ground (see the note below) Min/Max Current, Neutral (see the note below) NOTE: Min/Max values for Vng and In are not available from the display. Use the display to read registers (see “Read and Write Registers” on page 36) or the PM800 Min/Max Reading Table in SMS (refer to SMS Help for more information). © 2006 Schneider Electric. All Rights Reserved. 40 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 4—Metering Capabilities For each min/max value listed above, the following attributes are recorded by the Power Meter: Date/Time of minimum value Minimum value Phase of recorded minimum value Date/Time of maximum value Maximum value Phase of recorded maximum value NOTE: Phase of recorded min/max only applies to multi-phase quantities. NOTE: There are a couple of ways to view the min/max values. The Power Meter display can be used to view the min/max values since the meter was last reset. Using SMS, an instantaneous table with the current month’s and previous month’s min/max values can be viewed. © 2006 Schneider Electric. All Rights Reserved. 41 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 4—Metering Capabilities 6/2006 Power Factor Min/Max Conventions All running min/max values, except for power factor, are arithmetic minimum and maximum values. For example, the minimum phase A-B voltage is the lowest value in the range 0 to 1200 kV that has occurred since the min/max values were last reset. In contrast, because the power factor’s midpoint is unity (equal to one), the power factor min/max values are not true arithmetic minimums and maximums. Instead, the minimum value represents the measurement closest to -0 on a continuous scale for all real-time readings -0 to 1.00 to +0. The maximum value is the measurement closest to +0 on the same scale. Figure 4–1 below shows the min/max values in a typical environment in which a positive power flow is assumed. In the figure, the minimum power factor is -0.7 (lagging) and the maximum is 0.8 (leading). Note that the minimum power factor need not be lagging, and the maximum power factor need not be leading. For example, if the power factor values ranged from -0.75 to -0.95, then the minimum power factor would be -0.75 (lagging) and the maximum power factor would be -0.95 (lagging). Both would be negative. Likewise, if the power factor ranged from +0.9 to +0.95, the minimum would be +0.95 (leading) and the maximum would be +0.90 (leading). Both would be positive in this case. Figure 4–1: Power factor min/max example Minimum Maximum Power Factor Range of Power Power Factor -.7 (lagging) Factor Value .8 (leading) Unity 1.00 .8 .8 .6 .6 Lag Lead .4 .4 (–) (+) .2 .2 -0 +0 NOTE: Assumes a positive power flow © 2006 Schneider Electric. All Rights Reserved. 42 PLSD110165 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 4—Metering Capabilities An alternate power factor storage method is also available for use with analog outputs and trending. See the footnotes in “Register List” on page 124 for the applicable registers. Power Factor Sign Conventions The power meter can be set to one of two power factor sign conventions: IEEE or IEC. The Series 800 Power Meter defaults to the IEEE power factor sign convention. Figure 4–2 illustrates the two sign conventions. For instructions on changing the power factor sign convention, refer to “Advanced Power Meter Setup Options” on page 26. Figure 4–2: Power factor sign convention Reactive Reactive Power In Power In Quadrant Quadrant Quadrant Quadrant 2 2 1 1 watts negative (–) watts positive (+) watts negative (–) watts positive (+) vars positive (+) vars positive (+) vars positive (+) vars positive (+) power factor (–) power factor (+) power factor (+) power factor (–) Reverse Normal Reverse Normal Real Real Power Flow Power Flow Power Flow Power Flow Power Power In In watts negative (–) watts positive (+) watts negative (–) watts positive (+) vars negative (–) vars negative (–) vars negative (–) vars negative (–) power factor (–) power factor (+) power factor (–) power factor (+) Quadrant Quadrant Quadrant Quadrant 3 4 3 4 IEC Power Factor Sign Convention IEEE Power Factor Sign Convention Figure 4–3: Power Factor Display Example �,#%��0 ���� J The power ����� � factor sign is visible next to J ����� � the power factor reading. J ����� � J ����� ����- �� ���� ����- © 2006 Schneider Electric. All Rights Reserved. 43 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 4—Metering Capabilities 6/2006 Demand Readings The power meter provides a variety of demand readings, including coincident readings and predicted demands. Table 4–2 lists the available demand readings and their reportable ranges. Table 4–2: Demand Readings Demand Readings Reportable Range Demand Current, Per-Phase, 3Ø Average, Neutral Last Complete Interval 0 to 32,767 A Peak 0 to 32,767 A Average Power Factor (True), 3Ø Total Last Complete Interval –0.002 to 1.000 to +0.002 Coincident with kW Peak –0.002 to 1.000 to +0.002 Coincident with kVAR Peak –0.002 to 1.000 to +0.002 Coincident with kVA Peak –0.002 to 1.000 to +0.002 Demand Real Power, 3Ø Total Last Complete Interval 0 to ± 3276.70 MW Predicted 0 to ± 3276.70 MW Peak 0 to ± 3276.70 MW Coincident kVA Demand 0 to ± 3276.70 MVA Coincident kVAR Demand 0 to ± 3276.70 MVAR Demand Reactive Power, 3Ø Total Last Complete Interval 0 to ± 3276.70 MVAR Predicted 0 to ± 3276.70 MVAR Peak 0 to ± 3276.70 MVAR Coincident kVA Demand 0 to ± 3276.70 MVA Coincident kW Demand 0 to ± 3276.70 MW Demand Apparent Power, 3Ø Total Last Complete Interval 0 to ± 3276.70 MVA Predicted 0 to ± 3276.70 MVA Peak 0 to ± 3276.70 MVA Coincident kW Demand 0 to ± 3276.70 MW Coincident kVAR Demand 0 to ± 3276.70 MVAR © 2006 Schneider Electric. All Rights Reserved. 44 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 4—Metering Capabilities Demand Power Calculation Methods Demand power is the energy accumulated during a specified period divided by the length of that period. How the power meter performs this calculation depends on the method you select. To be compatible with electric utility billing practices, the power meter provides the following types of demand power calculations: Block Interval Demand Synchronized Demand Thermal Demand The default demand calculation is set to sliding block with a 15 minute interval. You can set up any of the demand power calculation methods from SMS. See the SMS online help to perform the set up using the software. Block Interval Demand In the block interval demand method, you select a “block” of time that the power meter uses for the demand calculation. You choose how the power meter handles that block of time (interval). Three different modes are possible: Sliding Block. In the sliding block interval, you select an interval from 1 to 60 minutes (in 1-minute increments). If the interval is between 1 and 15 minutes, the demand calculation updates every 15 seconds. If the interval is between 16 and 60 minutes, the demand calculation updates every 60 seconds. The power meter displays the demand value for the last completed interval. Fixed Block. In the fixed block interval, you select an interval from 1 to 60 minutes (in 1-minute increments). The power meter calculates and updates the demand at the end of each interval. Rolling Block. In the rolling block interval, you select an interval and a subinterval. The subinterval must divide evenly into the interval. For example, you might set three 5-minute subintervals for a 15-minute interval. Demand is updated at each subinterval. The power meter displays the demand value for the last completed interval. Figure 4–4 below illustrates the three ways to calculate demand power using the block method. For illustration purposes, the interval is set to 15 minutes. © 2006 Schneider Electric. All Rights Reserved. 45 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 4—Metering Capabilities 6/2006 Figure 4–4: Block Interval Demand Examples Calculation updates Demand value is the every 15 or 60 average for the last seconds completed interval 15-minute interval Time (sec) 15 3045 60 . . . Sliding Block Demand value is the average for Calculation updates at the last the end of the interval completed interval 15-minute interval 15-minute interval 15-min Time (min) 15 3045 Fixed Block Demand value is Calculation updates at the end of the average for the subinterval (5 minutes) the last completed interval 15-minute interval Time (min) 20 25 3540 15 3045 Rolling Block © 2006 Schneider Electric. All Rights Reserved. 46 PLSD110131 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 4—Metering Capabilities Synchronized Demand The demand calculations can be synchronized by accepting an external pulse input, a command sent over communications, or by synchronizing to the internal real-time clock. Input Synchronized Demand. You can set up the power meter to accept an input such as a demand synch pulse from an external source. The power meter then uses the same time interval as the other meter for each demand calculation. You can use the standard digital input installed on the meter to receive the synch pulse. When setting up this type of demand, you select whether it will be input-synchronized block or input-synchronized rolling block demand. The rolling block demand requires that you choose a subinterval. Command Synchronized Demand. Using command synchronized demand, you can synchronize the demand intervals of multiple meters on a communications network. For example, if a PLC input is monitoring a pulse at the end of a demand interval on a utility revenue meter, you could program the PLC to issue a command to multiple meters whenever the utility meter starts a new demand interval. Each time the command is issued, the demand readings of each meter are calculated for the same interval. When setting up this type of demand, you select whether it will be command-synchronized block or command-synchronized rolling block demand. The rolling block demand requires that you choose a subinterval. See Appendix B—Using the Command Interface on page 205 for more information. Clock Synchronized Demand . You can synchronize the demand interval to the internal real-time clock in the power meter. This enables you to synchronize the demand to a particular time, typically on the hour. The default time is 12:00 am. If you select another time of day when the demand intervals are to be synchronized, the time must be in minutes from midnight. For example, to synchronize at 8:00 am, select 480 minutes. When setting up this type of demand, you select whether it will be clock- synchronized block or clock-synchronized rolling block demand. The rolling block demand requires that you choose a subinterval. © 2006 Schneider Electric. All Rights Reserved. 47 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 4—Metering Capabilities 6/2006 Thermal Demand The thermal demand method calculates the demand based on a thermal response, which mimics thermal demand meters. The demand calculation updates at the end of each interval. You select the demand interval from 1 to 60 minutes (in 1-minute increments). In Figure 4–5 the interval is set to 15 minutes for illustration purposes. Figure 4–5: Thermal Demand Example The interval is a window of time that moves across the timeline 99% 90% Last completed demand interval 0% Time (minutes) 15-minute next interval 15-minute interval Calculation updates at the end of each interval Demand Current The power meter calculates demand current using the thermal demand method. The default interval is 15 minutes, but you can set the demand current interval between 1 and 60 minutes in 1-minute increments. Predicted Demand The power meter calculates predicted demand for the end of the present interval for kW, kVAR, and kVA demand. This prediction takes into account the energy consumption thus far within the present (partial) interval and the present rate of consumption. The prediction is updated every second. Figure 4–6 illustrates how a change in load can affect predicted demand for the interval. © 2006 Schneider Electric. All Rights Reserved. 48 PLSD110134 % of Lead ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 4—Metering Capabilities Figure 4–6: Predicted Demand Example Predicted demand is updated every second. Beginning of interval 15-minute interval Demand Predicted demand if load is for last Partial Interval added during interval; completed Demand predicted demand increases interval to reflect increase demand Predicted demand if no load is added. Time 1:00 1:06 1:15 Change in Load Peak Demand In nonvolatile memory, the power meter maintains a running maximum for power demand values, called “peak demand.” The peak is the highest average for each of these readings: kWD, kVARD, and kVAD since the last reset. The power meter also stores the date and time when the peak demand occurred. In addition to the peak demand, the power meter also stores the coinciding average 3-phase power factor. The average 3-phase power factor is defined as “demand kW/demand kVA” for the peak demand interval. Table 4–2 on page 44 lists the available peak demand readings from the power meter. You can reset peak demand values from the power meter display. From the Main Menu, select MAINT > RESET > DMD. You can also reset the values over the communications link by using SMS. See the SMS online help for instructions. NOTE: You should reset peak demand after changes to basic meter setup, such as CT ratio or system type. The power meter also stores the peak demand during the last incremental energy interval. See “Energy Readings” on page 53 for more about incremental energy readings. © 2006 Schneider Electric. All Rights Reserved. 49 PLSD110137 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 4—Metering Capabilities 6/2006 Generic Demand The power meter can perform any of the demand calculation methods, described earlier in this chapter, on up to 10 quantities that you choose. For generic demand, you do the following in SMS: Select the demand calculation method (thermal, block interval, or synchronized). Select the demand interval (from 5–60 minutes in 1–minute increments) and select the demand subinterval (if applicable). Select the quantities on which to perform the demand calculation. You must also select the units and scale factor for each quantity. Use the Device Setup > Basic Setup tab in SMS to create the generic demand profiles.For each quantity in the demand profile, the power meter stores four values: Partial interval demand value Last completed demand interval value Minimum values (date and time for each is also stored) Peak demand value (date and time for each is also stored) You can reset the minimum and peak values of the quantities in a generic demand profile by using one of two methods: Use SMS (see the SMS online help file), or Use the command interface. Command 5115 resets the generic demand profile. See Appendix B—Using the Command Interface on page 205 for more about the command interface. © 2006 Schneider Electric. All Rights Reserved. 50 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 4—Metering Capabilities Input Metering Demand The power meter has five input pulse metering channels, but only one digital input. Digital inputs can be added by installing one or more option modules (PM8M22, PM8M26, or PM8M2222). The input pulse metering channels count pulses received from one or more digital inputs assigned to that channel. Each channel requires a consumption pulse weight, consumption scale factor, demand pulse weight, and demand scale factor. The consumption pulse weight is the number of watt-hours or kilowatt-hours per pulse. The consumption scale factor is a factor of 10 multiplier that determines the format of the value. For example, if each incoming pulse represents 125 Wh, and you want consumption data in watt-hours, the consumption pulse weight is 125 and the consumption scale 0 factor is zero. The resulting calculation is 125 x 10 , which equals 125 watt-hours per pulse. If you want the consumption data in kilowatt- -3 hours, the calculation is 125 x 10 , which equals 0.125 kilowatt-hours per pulse.Time must be taken into account for demand data so you begin by calculating demand pulse weight using the following formula: watt-hours 3600 seconds pulse ----------------- ---------- - ---------------- ----------------- ---- ----- -------------- watts = × × pulse hour second If each incoming pulse represents 125 Wh, using the formula above you get 450,000 watts. If you want demand data in watts, the demand pulse weight is 450 and the demand scale factor is three. The 3 calculation is 450 x 10 , which equals 450,000 watts. If you want the 0 demand data in kilowatts, the calculation is 450 x 10 , which equals 450 kilowatts. NOTE: The power meter counts each input transition as a pulse. Therefore, for an input transition of OFF-to-ON and ON-to-OFF will be counted as two pulses.For each channel, the power meter maintains the following information: Total consumption Last completed interval demand—calculated demand for the last completed interval. Partial interval demand—demand calculation up to the present point during the interval. © 2006 Schneider Electric. All Rights Reserved. 51 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 4—Metering Capabilities 6/2006 Peak demand—highest demand value since the last reset of the input pulse demand. The date and time of the peak demand is also saved. Minimum demand—lowest demand value since the last reset of the input pulse demand. The date and time of the minimum demand is also saved. To use the channels feature, first set up the digital inputs from the display (see “Set Up I/Os” on page 24). Then using SMS, you must set the I/O operating mode to Normal and set up the channels. The demand method and interval that you select applies to all channels. See the SMS online help for instructions on device set up of the power meter. © 2006 Schneider Electric. All Rights Reserved. 52 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 4—Metering Capabilities Energy Readings The power meter calculates and stores accumulated energy values for real and reactive energy (kWh and kVARh) both into and out of the load, and also accumulates absolute apparent energy. Table 4–3 lists the energy values the power meter can accumulate. Table 4–3: Energy Readings Energy Reading, 3-Phase Reportable Range Shown on the Display Accumulated Energy Real (Signed/Absolute) ➀ -9,999,999,999,999,999 to 9,999,999,999,999,999 Wh Reactive (Signed/Absolute) ➀ -9,999,999,999,999,999 to 9,999,999,999,999,999 VARh 0000.000 kWh to 99,999.99 MWh Real (In) 0 to 9,999,999,999,999,999 Wh and Real (Out) ➀ 0 to 9,999,999,999,999,999 Wh 0000.000 to 99,999.99 MVARh Reactive (In) 0 to 9,999,999,999,999,999 VARh Reactive (Out) ➀ 0 to 9,999,999,999,999,999 VARh Apparent 0 to 9,999,999,999,999,999 VAh Accumulated Energy, Conditional Real (In) ➀ 0 to 9,999,999,999,999,999 Wh Real (Out) ➀ 0 to 9,999,999,999,999,999 Wh Not shown on the display. Reactive (In) ➀ 0 to 9,999,999,999,999,999 VARh Readings are obtained only through the communications link. Reactive (Out) ➀ 0 to 9,999,999,999,999,999 VARh Apparent ➀ 0 to 9,999,999,999,999,999 VAh Accumulated Energy, Incremental Real (In) ➀ 0 to 999,999,999,999 Wh Not shown on the display. Real (Out) ➀ 0 to 999,999,999,999 Wh Readings are obtained only Reactive (In) ➀ 0 to 999,999,999,999 VARh through the communications link. Reactive (Out) ➀ 0 to 999,999,999,999 VARh Apparent ➀ 0 to 999,999,999,999 VAh Reactive Energy Quadrant 1 ➀ 0 to 999,999,999,999 VARh Not shown on the display. Quadrant 2 ➀ 0 to 999,999,999,999 VARh Readings are obtained only Quadrant 3 ➀ 0 to 999,999,999,999 VARh through the communications link. Quadrant 4 ➀ 0 to 999,999,999,999 VARh ➀ Not shown on the power meter display. © 2006 Schneider Electric. All Rights Reserved. 53 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 4—Metering Capabilities 6/2006 The power meter can accumulate the energy values shown in Table 4–3 in one of two modes: signed or unsigned (absolute). In signed mode, the power meter considers the direction of power flow, allowing the magnitude of accumulated energy to increase and decrease. In unsigned mode, the power meter accumulates energy as a positive value, regardless of the direction of power flow. In other words, the energy value increases, even during reverse power flow. The default accumulation mode is unsigned. You can view accumulated energy from the display. The resolution of the energy value will automatically change through the range of 000.000 kWh to 000,000 MWh (000.000 kVAh to 000,000 MVARh), or it can be fixed. See Appendix A—Power Meter Register List on page 121 for the contents of the registers. For conditional accumulated energy readings, you can set the real, reactive, and apparent energy accumulation to OFF or ON when a particular condition occurs. You can do this over the communications link using a command, or from a digital input change. For example, you may want to track accumulated energy values during a particular process that is controlled by a PLC. The power meter stores the date and time of the last reset of conditional energy in nonvolatile memory. Also, the power meter provides an additional energy reading that is only available over the communications link: Four-quadrant reactive accumulated energy readings. The power meter accumulates reactive energy (kVARh) in four quadrants as shown in Figure 4–7. The registers operate in unsigned (absolute) mode in which the power meter accumulates energy as positive. © 2006 Schneider Electric. All Rights Reserved. 54 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 4—Metering Capabilities Figure 4–7: Reactive energy accumulates in four quadrants Reactive Power In Quadrant Quadrant 2 1 watts negative (–) watts positive (+) vars positive (+) vars positive (+) Reverse Normal Power Flow Real Power Flow Power In watts negative (–) watts positive (+) vars negative (–) vars negative (–) Quadrant Quadrant 3 4 © 2006 Schneider Electric. All Rights Reserved. 55 PLSD110171 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 4—Metering Capabilities 6/2006 Energy-Per-Shift The energy-per-shift feature allows the power meter to group energy usage based on three groups: 1st shift, 2nd shift, and 3rd shift. These groups provide a quick, historical view of energy usage and energy cost during each shift. All data is stored in nonvolatile memory. Table 4–4: Energy-per-shift recorded values Category Recorded Values Today Yesterday This Week Time Scales Last Week This Month Last Month Real Energy Apparent Today Yesterday This Week Energy Cost Last Week This Month Last Month Meter Reading Date User ConfigurationMeter Reading Time of Day 1st Day of the Week Configuration The start time of each shift is configured by setting registers using the display or by using SMS. The table below summarizes the quantities needed to configure energy-per-shift using register numbers. For SMS setup, refer to SMS Help. © 2006 Schneider Electric. All Rights Reserved. 56 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 4—Metering Capabilities Table 4–5: Energy-per-shift recorded values Quantity Register Number(s) Description 1st shift: 16171 For each shift, enter the minutes from 2nd shift: 16172 midnight at which the shift starts. 3rd shift: 16173 Defaults: Shift Start Time 1st shift = 420 minutes (7:00 am) 2nd shift = 900 minutes (3:00 pm) 3rd shift = 1380 minutes (11:00 pm) 1st shift: 16174 Cost per kWHr2nd shift: 16175 Enter the cost per kWHr for each shift. 3rd shift: 16176 The scale factor multiplied by the monetary units to determine the energy cost. Monetary Scale Factor 16177 Values: -3 to 3 Default: 0 © 2006 Schneider Electric. All Rights Reserved. 57 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 4—Metering Capabilities 6/2006 Power Analysis Values The power meter provides a number of power analysis values that can be used to detect power quality problems, diagnose wiring problems, and more. Table 4–6 on page 59 summarizes the power analysis values. THD. Total Harmonic Distortion (THD) is a quick measure of the total distortion present in a waveform and is the ratio of harmonic content to the fundamental. It provides a general indication of the “quality” of a waveform. THD is calculated for both voltage and current. The power meter uses the following equation to calculate THD where H is the harmonic distortion: 2 2 2 ++ + H H H 2 3 4 THD = x 100% H 1 thd. An alternate method for calculating Total Harmonic Distortion, used widely in Europe. It considers the total harmonic current and the total rms content rather than fundamental content in the calculation. The power meter calculates thd for both voltage and current. The power meter uses the following equation to calculate thd where H is the harmonic distortion: 2 2 2 ++ + H H H 2 3 4 x 100% thd = Total rms Displacement Power Factor. Power factor (PF) represents the degree to which voltage and current coming into a load are out of phase. Displacement power factor is based on the angle between the fundamental components of current and voltage. Harmonic Values. Harmonics can reduce the capacity of the power system. The power meter determines the individual per-phase harmonic magnitudes and angles through the: — 31st harmonic (PM820) or — 63rd harmonic (PM850, PM870) for all currents and voltages. The harmonic magnitudes can be formatted as either a percentage of the fundamental (default), a percentage of the rms value, or the actual rms value. Refer to © 2006 Schneider Electric. All Rights Reserved. 58 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 4—Metering Capabilities “Setting Up Individual Harmonic Calculations” on page 218 for information on how to configure harmonic calculations. Table 4–6: Power Analysis Values Value Reportable Range THD—Voltage, Current 3-phase, per-phase, neutral 0 to 3,276.7% thd—Voltage, Current 3-phase, per-phase, neutral 0 to 3,276.7% Fundamental Voltages (per phase) Magnitude 0 to 1,200 kV Angle 0.0 to 359.9° Fundamental Currents (per phase) Magnitude 0 to 32,767 A Angle 0.0 to 359.9° Miscellaneous Displacement P.F. (per phase, 3-phase) –0.002 to 1.000 to +0.002 Phase Rotation ABC or CBA Unbalance (current and voltage) ➀ 0.0 to 100.0% Individual Current and Voltage Harmonic Magnitudes ➁ 0 to 327.67% Individual Current and Voltage Harmonic Angles ➁ 0.0° to 359.9° ➀ Readings are obtained only through communications. ➁ Current and Voltage Harmonic Magnitude and Angles 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, and 13 are shown on the display. © 2006 Schneider Electric. All Rights Reserved. 59 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 4—Metering Capabilities 6/2006 © 2006 Schneider Electric. All Rights Reserved. 60 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 5—Input/Output Capabilities CHAPTER 5—INPUT/OUTPUT CAPABILITIES Digital Inputs The power meter includes one solid-state digital input. A digital input is used to detect digital signals. For example, the digital input can be used to determine circuit breaker status, count pulses, or count motor starts. The digital input can also be associated with an external relay. You can log digital input transitions as events in the power meter’s on-board alarm log. The event is date and time stamped with resolution to the second. The power meter counts OFF-to-ON transitions for each input. You can view the count for each input using the Digital Inputs screen, and you can reset this value using the command interface. Figure 5–1 is an example of the Digital Inputs screen. Figure 5–1: Digital Inputs Screen A. Lit bargraph indicates that the input is ON. For analog inputs or outputs, the bargraph indicates the output ��.���-������� percentage. A B. S1 is common to all meters and ��������� represents standard digital input. �������������� ��� C. A-S1 and A-S2 represent I/O point =� B numbers on the first (A) module. ��������� D. Use the arrow buttons to scroll through �������������� ��� the remaining I/O points. Point numbers "���� beginning with “B” are on the second C ��������� module. See Table B–3 on page 211 for �������������� ��� a complete list of I/O point numbers. ���& ��� ���� D © 2006 Schneider Electric. All Rights Reserved. 61 PLSD110233 ���� ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 5—Input/Output Capabilities 6/2006 The digital input has three operating modes: Normal—Use the normal mode for simple on/off digital inputs. In normal mode, digital inputs can be used to count KY pulses for demand and energy calculation. Demand Interval Synch Pulse—you can configure any digital input to accept a demand synch pulse from a utility demand meter (see “Demand Synch Pulse Input” on page 63 of this chapter for more about this topic). For each demand profile, you can designate only one input as a demand synch input. Conditional Energy Control—you can configure one digital input to control conditional energy (see “Energy Readings” on page 53 in Chapter 4—Metering Capabilities for more about conditional energy). NOTE: By default, the digital input is named DIG IN S02 and is set up for normal mode. For custom setup, use SMS to define the name and operating mode of the digital input. The name is a 16-character label that identifies the digital input. The operating mode is one of those listed above. See the SMS online help for instructions on device set up of the power meter. © 2006 Schneider Electric. All Rights Reserved. 62 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 5—Input/Output Capabilities Demand Synch Pulse Input You can configure the power meter to accept a demand synch pulse from an external source such as another demand meter. By accepting demand synch pulses through a digital input, the power meter can make its demand interval “window” match the other meter’s demand interval “window.” The power meter does this by “watching” the digital input for a pulse from the other demand meter. When it sees a pulse, it starts a new demand interval and calculates the demand for the preceding interval. The power meter then uses the same time interval as the other meter for each demand calculation. Figure 5–2 illustrates this point. See “Synchronized Demand” on page 47 in Chapter 4—Metering Capabilities for more about demand calculations. When in demand synch pulse operating mode, the power meter will not start or stop a demand interval without a pulse. The maximum allowable time between pulses is 60 minutes. If 66 minutes (110% of the demand interval) pass before a synch pulse is received, the power meter throws out the demand calculations and begins a new calculation when the next pulse is received. Once in synch with the billing meter, the power meter can be used to verify peak demand charges. Important facts about the power meter’s demand synch feature are listed below: Any installed digital input can be set to accept a demand synch pulse. Each system can choose whether to use an external synch pulse, but only one demand synch pulse can be brought into the meter for each demand system. One input can be used to synchronize any combination of the demand systems. The demand synch feature can be set up from SMS. See the SMS online help for instructions on device set up of the power meter. © 2006 Schneider Electric. All Rights Reserved. 63 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 5—Input/Output Capabilities 6/2006 Figure 5–2: Demand synch pulse timing Normal Demand Mode External Synch Pulse Demand Timing Billing Meter Billing Meter Demand Timing Demand Timing Utility Meter Synch Pulse Power Meter Power Meter Demand Timing Demand Timing (Slave to Master) Relay Output Operating Modes The relay output defaults to external control, but you can choose whether the relay is set to external or internal control: Remote (external) control—the relay is controlled either from a PC using SMS or a programmable logic controller using commands via communications. Power meter (internal) control—the relay is controlled by the power meter in response to a set-point controlled alarm condition, or as a pulse initiator output. Once you’ve set up a relay for power meter control, you can no longer operate the relay remotely. However, you can temporarily override the relay, using SMS. NOTE: If any basic setup parameters or I/O setup parameters are modified, all relay outputs will be de-energized. The 11 relay operating modes are as follows: Normal — Remotely Controlled: Energize the relay by issuing a command from a remote PC or programmable controller. The relay remains energized until a command to de-energize is issued from the remote PC or programmable controller, or until the power meter loses control power. When control power is restored, the relay is not automatically re-energized. — Power Meter Controlled: When an alarm condition assigned to the relay occurs, the relay is energized. The relay is not de- energized until all alarm conditions assigned to the relay have dropped out, the power meter loses control power, or the © 2006 Schneider Electric. All Rights Reserved. 64 PLSD110140 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 5—Input/Output Capabilities alarms are over-ridden using SMS software. If the alarm condition is still true when the power meter regains control power, the relay will be re-energized. Latched — Remotely Controlled: Energize the relay by issuing a command from a remote PC or programmable controller. The relay remains energized until a command to de-energize is issued from a remote PC or programmable controller, or until the power meter loses control power. When control power is restored, the relay will not be re-energized. — Power Meter Controlled: When an alarm condition assigned to the relay occurs, the relay is energized. The relay remains energized—even after all alarm conditions assigned to the relay have dropped out—until a command to de-energize is issued from a remote PC or programmable controller, until the high priority alarm log is cleared from the display, or until the power meter loses control power. When control power is restored, the relay will not be re-energized if the alarm condition is not TRUE. Timed — Remotely Controlled: Energize the relay by issuing a command from a remote PC or programmable controller. The relay remains energized until the timer expires, or until the power meter loses control power. If a new command to energize the relay is issued before the timer expires, the timer restarts. If the power meter loses control power, the relay will not be re-energized when control power is restored and the timer will reset to zero and begin timing again. — Power Meter Controlled: When an alarm condition assigned to the relay occurs, the relay is energized. The relay remains energized for the duration of the timer. When the timer expires, the relay will de-energize and remain de-energized. If the relay is on and the power meter loses control power, the relay will not be re-energized when control power is restored and the timer will reset to zero and begin timing again. End Of Power Demand Interval This mode assigns the relay to operate as a synch pulse to another device. The output operates in timed mode using the timer setting and turns on at the end of a power demand interval. It turns off when the timer expires. © 2006 Schneider Electric. All Rights Reserved. 65 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 5—Input/Output Capabilities 6/2006 Absolute kWh Pulse This mode assigns the relay to operate as a pulse initiator with a user-defined number of kWh per pulse. In this mode, both forward and reverse real energy are treated as additive (as in a tie circuit breaker). Absolute kVARh Pulse This mode assigns the relay to operate as a pulse initiator with a user-defined number of kVARh per pulse. In this mode, both forward and reverse reactive energy are treated as additive (as in a tie circuit breaker). kVAh Pulse This mode assigns the relay to operate as a pulse initiator with a user-defined number of kVAh per pulse. Since kVA has no sign, the kVAh pulse has only one mode. kWh In Pulse This mode assigns the relay to operate as a pulse initiator with a user-defined number of kWh per pulse. In this mode, only the kWh flowing into the load is considered. kVARh In Pulse This mode assigns the relay to operate as a pulse initiator with a user-defined number of kVARh per pulse. In this mode, only the kVARh flowing into the load is considered. kWh Out Pulse This mode assigns the relay to operate as a pulse initiator with a user-defined number of kWh per pulse. In this mode, only the kWh flowing out of the load is considered. kVARh Out Pulse This mode assigns the relay to operate as a pulse initiator with a user-defined number of kVARh per pulse. In this mode, only the kVARh flowing out of the load is considered. The last seven modes in the list above are for pulse initiator applications. All Series 800 Power Meters are equipped with one solid-state KY pulse output rated at 100 mA. The solid-state KY output provides the long life—billions of operations—required for pulse initiator applications. The KY output is factory configured with Name = KY, Mode = Normal, and Control = External. To set up custom values, press SETUP > I/O. For detailed instructions, see “Set Up I/Os” on page 24. Then using © 2006 Schneider Electric. All Rights Reserved. 66 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 5—Input/Output Capabilities SMS, you must define the following values for each mechanical relay output: Name—A 16-character label used to identify the digital output. Mode—Select one of the operating modes listed above. Pulse Weight—You must set the pulse weight, the multiplier of the unit being measured, if you select any of the pulse modes (last 7 listed above). Timer—You must set the timer if you select the timed mode or end of power demand interval mode (in seconds). Control—You must set the relay to be controlled either remotely or internally (from the power meter) if you select the normal, latched, or timed mode. For instructions on setting up digital I/Os in SMS, see the SMS online help on device set up of the power meter. © 2006 Schneider Electric. All Rights Reserved. 67 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 5—Input/Output Capabilities 6/2006 Solid-state KY Pulse Output This section describes the pulse output capabilities of the power meter. For instructions on wiring the KY pulse output, see “Wiring the Solid-State KY Output” in Chapter 5—Wiring of the installation manual. The power meter units are equipped with one onboard, solid-state KY pulse output. This solid-state relay provides the extremely long life— billions of operations—required for pulse initiator applications. The KY output is a Form-A contact with a maximum rating of 100 mA. Because most pulse initiator applications feed solid-state receivers with low burdens, this 100 mA rating is adequate for most applications. To set the kilowatthour-per-pulse value, use SMS or the display. When setting the kWh/pulse value, set the value based on a 2-wire pulse output. For instructions on calculating the correct value, see “Calculating the Kilowatthour-Per-Pulse Value” on page 69 in this chapter. The KY pulse output can be configured to operate in one of 11 operating modes. See “Relay Output Operating Modes” on page 64 for a description of the modes. 2-wire Pulse Initiator Figure 5–3 shows a pulse train from a 2-wire pulse initiator application. Figure 5–3: Two-wire pulse train Y K 3 12 KY ΔT In Figure 5–3, the transitions are marked as 1 and 2. Each transition represents the time when the relay contact closes. Each time the relay transitions, the receiver counts a pulse. The power meter can deliver up to 12 pulses per second in a 2-wire application. © 2006 Schneider Electric. All Rights Reserved. 68 PLSD110122 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 5—Input/Output Capabilities Calculating the Kilowatthour-Per-Pulse Value This section shows an example of how to calculate kilowatthours per pulse. To calculate this value, first determine the highest kW value you can expect and the required pulse rate. In this example, the following assumptions are made: The metered load should not exceed 1600 kW. About two KY pulses per second should occur at full scale. Step 1: Convert 1600 kW load into kWh/second. (1600 kW)(1 Hr) = 1600 kWh (1600 kWh) X kWh ------ ----- ----- ------ ----- --- - = ----- ----- ------ ----- --- 1 hour 1 second (1600 kWh) X kWh --- ----- ------ ----- ----- ------ ----- -- = -- ------ ----- ----- ------ 3600 seconds 1 second X== 1600/3600 0.444 kWh/second Step 2: Calculate the kWh required per pulse. 0.444 kWh/second ----- ------ ----- ----- ------ ----- ----- ----- ------ - = 0.2222 kWh/pulse 2 pulses/second Step 3: Adjust for the KY initiator (KY will give one pulse per two transitions of the relay). 0.2222 kWh/second ----- ----- ----- ------ ----- ----- ------ ----- ----- ----- - = 0.1111 kWh/pulse 2 Step 4: Round to nearest hundredth, since the power meter only accepts 0.01 kWh increments. Ke = 0.11 kWh/pulse © 2006 Schneider Electric. All Rights Reserved. 69 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 5—Input/Output Capabilities 6/2006 Analog Inputs With a PM8M2222 option module installed, a power meter can accept either voltage or current signals through the analog inputs on the option module. The Power Meter stores a minimum and a maximum value for each analog input. For technical specifications and instructions on installing and configuring the analog inputs on the PM8M2222, refer to the instruction bulletin (63230-502-200) that ships with the option module. To set up an analog input, you must first set it up from the display. From the SUMMARY screen, select MAINT > SETUP > I/O, then select the appropriate analog input option. Then, in SMS define the following values for each analog input: Name—a 16-character label used to identify the analog input. Units—the units of the monitored analog value (for example, “psi”). Scale factor—multiplies the units by this value (such as tenths or hundredths). Report Range Lower Limit—the value the Power Meter reports when the input reaches a minimum value. When the input current is below the lowest valid reading, the Power Meter reports the lower limit. Report Range Upper Limit—the value the circuit monitor reports when the input reaches the maximum value. When the input current is above highest valid reading, the Power Meter reports the upper limit. For instructions on setting up analog inputs in SMS, see device set up of the Power Meter in the SMS online Help. © 2006 Schneider Electric. All Rights Reserved. 70 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 5—Input/Output Capabilities Analog Outputs This section describes the analog output capabilities when a PM8M2222 is installed on the Power Meter. For technical specifications and instructions on installing and configuring the analog outputs on the PM8M2222, refer to the instruction bulletin (63230-502-200) that ships with the option module. To set up an analog output, you must first set it up from the display. From the SUMMARY screen, select MAINT > SETUP > I/O, then select the appropriate analog output option. Then, in SMS define the following values for each analog input Name—A 16-character label used to identify the output. Default names are assigned, but can be customized Output register—The Power Meter register assigned to the analog output. Lower Limit—The value equivalent to the minimum output current. When the register value is below the lower limit, the Power Meter outputs the minimum output current. Upper Limit—The value equivalent to the maximum output current. When the register value is above the upper limit, the Power Meter outputs the maximum output current. For instructions on setting up an analog output in SMS, see the SMS online help on device set up of the Power Meter. © 2006 Schneider Electric. All Rights Reserved. 71 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 5—Input/Output Capabilities 6/2006 © 2006 Schneider Electric. All Rights Reserved. 72 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 6—Basic Alarms CHAPTER 6—BASIC ALARMS This section describes the basic alarm features on all Series 800 Power Meters. For information about advanced alarm features, see Chapter 7—Advanced Alarms on page89. About Alarms The power meter can detect over 50 alarm conditions, including over or under conditions, digital input changes, phase unbalance conditions, and more. It also maintains a counter for each alarm to keep track of the total number of occurrences. A complete list of default alarm configurations are described in Table 6–4 on page 84. When one or more alarm conditions are true, the power meter will execute a task automatically. An ! alarm icon appears in the upper- right corner of the power meter display, indicating that an alarm is active. Using SMS, you can set up each alarm condition to force data log entries in up to three user-defined data log files. See Chapter 8— Logging on page95 for more about data logging. NOTE: PM820 only supports one data log. Table 6–1: Basic alarm features by model Basic Alarm Feature PM820 PM850 PM870 Standard alarms 33 33 33 Open slots for additional standard alarms 7 7 7 ➀ ➀ ➀ Digital 12 12 12 Custom alarms Yes Yes Yes ➀ Requires an input/output option module (PM8M22, PM8M26, or the PM8M2222). © 2006 Schneider Electric. All Rights Reserved. 73 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 6—Basic Alarms 6/2006 Basic Alarm Groups Whether you are using a default alarm or creating a custom alarm, you first choose the alarm group that is appropriate for the application. Each alarm condition is assigned to one of these alarm groups: Standard—Standard alarms have a detection rate of 1 second and are useful for detecting conditions such as over current and under voltage. Up to 40 alarms can be set up in this alarm group. Digital—Digital alarms are triggered by an exception such as the transition of a digital input or the end of an incremental energy interval. Up to 12 alarms can be set up in this group. Custom—The power meter has many pre-defined alarms, but you can also set up your own custom alarms using SMS. For example, you may need to alarm on the ON-to-OFF transition of a digital input. To create this type of custom alarm: 1. Select the appropriate alarm group (digital in this case). 2. Select the type of alarm (described in Table 6–5 on page 85). 3. Give the alarm a name. 4. Save the custom alarm. After creating a custom alarm, you can configure it by applying priorities, setting pickups and dropouts (if applicable), and so forth. SMS and the Power Meter display can be used to setup standard, digital, and custom alarm types. © 2006 Schneider Electric. All Rights Reserved. 74 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 6—Basic Alarms Setpoint-driven Alarms Many of the alarm conditions require that you define setpoints. This includes all alarms for over, under, and phase unbalance alarm conditions. Other alarm conditions such as digital input transitions and phase reversals do not require setpoints. For those alarm conditions that require setpoints, you must define the following information: Pickup Setpoint Pickup Delay Dropout Setpoint Dropout Delay NOTE: Alarms with both Pickup and Dropout setpoints set to zero are invalid. To understand how the power meter handles setpoint-driven alarms, see Figure 6–2 on page 76. Figure 6–1 shows what the actual alarm Log entries for Figure 6–2 might look like, as displayed by SMS. NOTE: The software does not actually display the codes in parentheses—EV1, EV2, Max1, Max2. These are references to the codes in Figure 6–2. Figure 6–1: Sample alarm log entry EV2 Max2 EV1 Max1 © 2006 Schneider Electric. All Rights Reserved. 75 PLSD110219 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 6—Basic Alarms 6/2006 Figure 6–2: How the power meter handles setpoint-driven alarms Max2 Max1 Pickup Setpoint Dropout Setpoint Pickup Delay Dropout Delay EV2 EV1 Alarm Period EV1—The power meter records the date and time that the pickup setpoint and time delay were satisfied, and the maximum value reached (Max1) during the pickup delay period (ΔT). Also, the power meter performs any tasks assigned to the event such as waveform captures or forced data log entries. EV2—The power meter records the date and time that the dropout setpoint and time delay were satisfied, and the maximum value reached (Max2) during the alarm period. The power meter also stores a correlation sequence number (CSN) for each event (such as Under Voltage Phase A Pickup, Under Voltage Phase A Dropout). The CSN lets you relate pickups and dropouts in the alarm log. You can sort pickups and dropouts by CSN to correlate the pickups and dropouts of a particular alarm. The pickup and dropout entries of an alarm will have the same CSN. You can also calculate the duration of an event by looking at pickups and dropouts with the same CSN. © 2006 Schneider Electric. All Rights Reserved. 76 PLSD110143 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 6—Basic Alarms Priorities Each alarm also has a priority level. Use the priorities to distinguish between events that require immediate action and those that do not require action. High priority—if a high priority alarm occurs, the display informs you in two ways: the LED backlight on the display flashes until you acknowledge the alarm and the alarm icon blinks while the alarm is active. Medium priority—if a medium priority alarm occurs, the alarm icon blinks only while the alarm is active. Once the alarm becomes inactive, the alarm icon stops blinking and remains on the display. Low priority—if a low priority alarm occurs, the alarm icon blinks only while the alarm is active. Once the alarm becomes inactive, the alarm icon disappears from the display. No priority—if an alarm is setup with no priority, no visible representation will appear on the display. Alarms with no priority are not entered in the Alarm Log. See Chapter 8—Logging for alarm logging information. If multiple alarms with different priorities are active at the same time, the display shows the alarm message for the last alarm that occurred. For instructions on setting up alarms from the power meter display, see “Set Up Alarms” on page 23. Viewing Alarm Activity and History 1. Press ###: until ALARM is visible. 2. Press ALARM. �’���’�� �� 3. View the active alarm listed on the power meter display. If there are no active alarms, ����� ����� the screen reads, “NO ACTIVE ALARMS.” ��� ; 4. If there are active alarms, press <--or --> to view a different alarm. ��� �"2= 5. Press HIST. �������� �K�5� 6. Press <-- or --> to view a different alarm’s history. �� ��� ��H ����’ 7. Press 1; to return to the SUMMARY screen. © 2006 Schneider Electric. All Rights Reserved. 77 PLSD110258 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 6—Basic Alarms 6/2006 Types of Setpoint-controlled Functions This section describes some common alarm functions to which the following information applies: Values that are too large to fit into the display may require scale factors. For more information on scale factors, refer to “Changing Scale Factors” on page 219. Relays can be configured as normal, latched, or timed. See “Relay Output Operating Modes” on page 64 in Chapter 5— Input/Output Capabilities for more information. When the alarm occurs, the power meter operates any specified relays. There are two ways to release relays that are in latched mode: — Issue a command to de-energize a relay. See Appendix B— Using the Command Interface for instructions on using the command interface, or — Acknowledge the alarm in the high priority log to release the relays from latched mode. From the main menu of the display, press ALARM to view and acknowledge unacknowledged alarms. The list that follows shows the types of alarms available for some common alarm functions: NOTE: Voltage based alarm setpoints depend on your system configuration. Alarm setpoints for 3-wire systems are V values L-L while 4-wire systems are V values. L-N Undervoltage: Pickup and dropout setpoints are entered in volts. The per-phase undervoltage alarm occurs when the per-phase voltage is equal to or below the pickup setpoint long enough to satisfy the specified pickup delay (in seconds). The undervoltage alarm clears when the phase voltage remains above the dropout setpoint for the specified dropout delay period. Overvoltage: Pickup and dropout setpoints are entered in volts. The per-phase overvoltage alarm occurs when the per-phase voltage is equal to or above the pickup setpoint long enough to satisfy the specified pickup delay (in seconds). The overvoltage alarm clears when the phase voltage remains below the dropout setpoint for the specified dropout delay period. Unbalance Current: Pickup and dropout setpoints are entered in tenths of percent, based on the percentage difference between each © 2006 Schneider Electric. All Rights Reserved. 78 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 6—Basic Alarms phase current with respect to the average of all phase currents. For example, enter an unbalance of 7% as 70. The unbalance current alarm occurs when the phase current deviates from the average of the phase currents, by the percentage pickup setpoint, for the specified pickup delay. The alarm clears when the percentage difference between the phase current and the average of all phases remains below the dropout setpoint for the specified dropout delay period. Unbalance Voltage: Pickup and dropout setpoints are entered in tenths of percent, based on the percentage difference between each phase voltage with respect to the average of all phase voltages. For example, enter an unbalance of 7% as 70. The unbalance voltage alarm occurs when the phase voltage deviates from the average of the phase voltages, by the percentage pickup setpoint, for the specified pickup delay. The alarm clears when the percentage difference between the phase voltage and the average of all phases remains below the dropout setpoint for the specified dropout delay (in seconds). Phase Loss—Current: Pickup and dropout setpoints are entered in amperes. The phase loss current alarm occurs when any current value (but not all current values) is equal to or below the pickup setpoint for the specified pickup delay (in seconds). The alarm clears when one of the following is true: All of the phases remain above the dropout setpoint for the specified dropout delay, or All of the phases drop below the phase loss pickup setpoint. If all of the phase currents are equal to or below the pickup setpoint, during the pickup delay, the phase loss alarm will not activate. This is considered an under current condition. It should be handled by configuring the under current alarm functions. Phase Loss—Voltage: Pickup and dropout setpoints are entered in volts. The phase loss voltage alarm occurs when any voltage value (but not all voltage values) is equal to or below the pickup setpoint for the specified pickup delay (in seconds). The alarm clears when one of the following is true: All of the phases remain above the dropout setpoint for the specified dropout delay (in seconds), OR All of the phases drop below the phase loss pickup setpoint. © 2006 Schneider Electric. All Rights Reserved. 79 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 6—Basic Alarms 6/2006 If all of the phase voltages are equal to or below the pickup setpoint, during the pickup delay, the phase loss alarm will not activate. This is considered an under voltage condition. It should be handled by configuring the under voltage alarm functions. Reverse Power: Pickup and dropout setpoints are entered in kilowatts or kVARs. The reverse power alarm occurs when the power flows in a negative direction and remains at or below the negative pickup value for the specified pickup delay (in seconds). The alarm clears when the power reading remains above the dropout setpoint for the specified dropout delay (in seconds). Phase Reversal: Pickup and dropout setpoints and delays do not apply to phase reversal. The phase reversal alarm occurs when the phase voltage rotation differs from the default phase rotation. The power meter assumes that an ABC phase rotation is normal. If a CBA phase rotation is normal, the user must change the power meter’s phase rotation from ABC (default) to CBA. To change the phase rotation from the display, from the main menu select Setup > Meter > Advanced. For more information about changing the phase rotation setting of the power meter, refer to “Advanced Power Meter Setup Options” on page 26. © 2006 Schneider Electric. All Rights Reserved. 80 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 6—Basic Alarms Scale Factors A scale factor is the multiplier expressed as a power of 10. For example, a multiplier of 10 is represented as a scale factor of 1, since 1 10 =10; a multiplier of 100 is represented as a scale factor of 2, since 2 10 =100. This allows you to make larger values fit into the register. Normally, you do not need to change scale factors. If you are creating custom alarms, you need to understand how scale factors work so that you do not overflow the register with a number larger than what the register can hold. When SMS is used to set up alarms, it automatically handles the scaling of pickup and dropout setpoints. When creating a custom alarm using the power meter’s display, do the following: Determine how the corresponding metering value is scaled, and Take the scale factor into account when entering alarm pickup and dropout settings. Pickup and dropout settings must be integer values in the range of -32,767 to +32,767. For example, to set up an under voltage alarm for a 138 kV nominal system, decide upon a setpoint value and then convert it into an integer between -32,767 and +32,767. If the under voltage setpoint were 125,000 V, this would typically be converted to 12500 x 10 and entered as a setpoint of 12500. Six scale groups are defined (A through F). The scale factor is preset for all factory-configured alarms. Table 6–2 on page 82 lists the available scale factors for each of the scale groups. If you need either an extended range or more resolution, select any of the available scale factors to suit your need. Refer to “Changing Scale Factors” on page 219 of Appendix B—Using the Command Interface. © 2006 Schneider Electric. All Rights Reserved. 81 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 6—Basic Alarms 6/2006 Table 6–2: Scale Groups Scale Group Measurement Range Scale Factor Amperes 0–327.67 A –2 Scale Group A—Phase Current 0–3,276.7 A –1 0–32,767 A 0 (default) 0–327.67 kA 1 Amperes 0–327.67 A –2 Scale Group B—Neutral Current 0–3,276.7 A –1 0–32,767 A 0 (default) 0–327.67 kA 1 Voltage 0–3,276.7 V –1 Scale Group D—Voltage 0–32,767 V 0 (default) 0–327.67 kV 1 0–3,276.7 kV 2 Power 0–32.767 kW, kVAR, kVA –3 0–327.67 kW, kVAR, kVA –2 0–3,276.7 kW, kVAR, kVA –1 Scale Group F—Power kW, kVAR, kVA 0–32,767 kW, kVAR, kVA 0 (default) 0–327.67 MW, MVAR, MVA 1 0–3,276.7 MW, MVAR, MVA 2 0–32,767 MW, MVAR, MVA 3 © 2006 Schneider Electric. All Rights Reserved. 82 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 6—Basic Alarms Scaling Alarm Setpoints This section is for users who do not have SMS and must set up alarms from the power meter display. It explains how to scale alarm setpoints. When the power meter is equipped with a display, most metered quantities are limited to five characters (plus a positive or negative sign). The display will also show the engineering units applied to that quantity. To determine the proper scaling of an alarm setpoint, view the register number for the associated scale group. The scale factor is the number in the Dec column for that register. For example, the register number for Scale D to Phase Volts is 3212. If the number in 1 the Dec column is 1, the scale factor is 10 (10 =10). Remember that scale factor 1 in Table 6–3 on page 83 for Scale Group D is measured in kV. Therefore, to define an alarm setpoint of 125 kV, enter 12.5 because 12.5 multiplied by 10 is 125. Below is a table listing the scale groups and their register numbers. Table 6–3: Scale Group Register Numbers Scale Group Register Number Scale Group A—Phase Current 3209 Scale Group B—Neutral Current 3210 Scale Group C—Ground Current 3211 Scale Group D—Voltage 3212 Scale Group F—Power kW, kVAR, kVA 3214 Alarm Conditions and Alarm Numbers This section lists the power meter’s predefined alarm conditions. For each alarm condition, the following information is provided. Alarm No.—a position number indicating where an alarm falls in the list. Alarm Description—a brief description of the alarm condition Abbreviated Display Name—an abbreviated name that describes the alarm condition, but is limited to 15 characters that fit in the window of the power meter’s display. Test Register—the register number that contains the value (where applicable) that is used as the basis for a comparison to alarm pickup and dropout settings. Units—the unit that applies to the pickup and dropout settings. © 2006 Schneider Electric. All Rights Reserved. 83 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 6—Basic Alarms 6/2006 Scale Group—the scale group that applies to the test register’s metering value (A–F). For a description of scale groups, see “Scale Factors” on page 81. Alarm Type—a reference to a definition that provides details on the operation and configuration of the alarm. For a description of alarm types, refer to Table 6–5 on page 85. Table 6–4 on page 84 lists the preconfigured alarms by alarm number. Table 6–5 on page 87 lists the default alarm configurations. Table 6–4: List of Default Basic Alarms by Alarm Number Alarm Abbreviated Test Scale Alarm Alarm Description Units ➀ ➁ Number Display Name Register Group Type Standard Speed Alarms (1 Second) 01 Over Current Phase A Over Ia 1100 Amperes A 010 02 Over Current Phase B Over Ib 1101 Amperes A 010 03 Over Current Phase C Over Ic 1102 Amperes A 010 04 Over Current Neutral Over In 1103 Amperes B 010 05 Current Unbalance, Max I Unbal Max 1110 Tenths % — 010 06 Current Loss Current Loss 3262 Amperes A 053 07 Over Voltage Phase A–N Over Van 1124 Volts D 010 08 Over Voltage Phase B–N Over Vbn 1125 Volts D 010 09 Over Voltage Phase C–N Over Vcn 1126 Volts D 010 10 Over Voltage Phase A–B Over Vab 1120 Volts D 010 11 Over Voltage Phase B–C Over Vbc 1121 Volts D 010 12 Over Voltage Phase C–A Over Vca 1122 Volts D 010 13 Under Voltage Phase A Under Van 1124 Volts D 020 14 Under Voltage Phase B Under Vbn 1125 Volts D 020 15 Under Voltage Phase C Under Vcn 1126 Volts D 020 16 Under Voltage Phase A–B Under Vab 1120 Volts D 020 17 Under Voltage Phase B–C Under Vbc 1121 Volts D 020 18 Under Voltage Phase C–A Under Vca 1122 Volts D 020 19 Voltage Unbalance L–N, Max V Unbal L-N Max 1136 Tenths % — 010 20 Voltage Unbalance L–L, Max V Unbal L-L Max 1132 Tenths % — 010 Voltage Loss (loss of A,B,C, but 21 Voltage Loss 3262 Volts D 052 not all) 22 Phase Reversal Phase Rev 3228 — — 051 23 Over kW Demand Over kW Dmd 2151 kW F 011 24 Lagging true power factor Lag True PF 1163 Thousandths — 055 ➀ Scale groups are described in Table 6–2 on page 82. ➁ Alarm types are described in Table 6–5 on page 85. © 2006 Schneider Electric. All Rights Reserved. 84 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 6—Basic Alarms Table 6–4: List of Default Basic Alarms by Alarm Number Alarm Abbreviated Test Scale Alarm Alarm Description Units ➀ ➁ Number Display Name Register Group Type 25 Over THD of Voltage Phase A–N Over THD Van 1207 Tenths % 26 Over THD of Voltage Phase B–N Over THD Vbn 1208 Tenths % 27 Over THD of Voltage Phase C–N Over THD Vcn 1209 Tenths % 28 Over THD of Voltage Phase A–B Over THD Vab 1211 Tenths % 29 Over THD of Voltage Phase B–C Over THD Vbc 1212 Tenths % 30 Over THD of Voltage Phase C–A Over THD Vca 1213 Tenths % 31 Over kVA Demand Over kVA Dmd 2181 32 Over kW Total Over kW Total 1143 33 Over kVA Total Over kVA Total 1151 34-40 Reserved for custom alarms. — — — — — Digital End of incremental energy 01 End Inc Enr Int N/A — — 070 interval 02 End of power demand interval End Dmd Int N/A — — 070 03 Power up/Reset Pwr Up/Reset N/A — — 070 04 Digital Input OFF/ON DIG IN S02 2 — — 060 05-12 Reserved for custom alarms — — — — — ➀ Scale groups are described in Table 6–2 on page 82. ➁ Alarm types are described in Table 6–5 on page 85. Table 6–5: Alarm Types Type Description Operation Standard Speed If the test register value exceeds the setpoint long enough to satisfy the pickup delay period, the alarm condition will be true. When the value in 010 Over Value Alarm the test register falls below the dropout setpoint long enough to satisfy the dropout delay period, the alarm will dropout. Pickup and dropout setpoints are positive, delays are in seconds. If the absolute value in the test register exceeds the setpoint long enough to satisfy the pickup delay period, the alarm condition will be true. When absolute the value in the test register falls below the dropout 011 Over Power Alarm setpoint long enough to satisfy the dropout delay period, the alarm will dropout. Pickup and dropout setpoints are positive, delays are in seconds. If the absolute value in the test register exceeds the setpoint long enough to satisfy the pickup delay period, the alarm condition will be true. When absolute the value in the test register falls below the dropout 012 Over Reverse Power Alarm setpoint long enough to satisfy the dropout delay period, the alarm will dropout. This alarm will only hold true for reverse power conditions. Positive power values will not cause the alarm to occur. Pickup and dropout setpoints are positive, delays are in seconds. © 2006 Schneider Electric. All Rights Reserved. 85 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 6—Basic Alarms 6/2006 Table 6–5: Alarm Types Type Description Operation If the test register value is below the setpoint long enough to satisfy the pickup delay period, the alarm condition will be true. When the value in 020 Under Value Alarm the test register rises above the dropout setpoint long enough to satisfy the dropout delay period, the alarm will dropout. Pickup and dropout setpoints are positive, delays are in seconds. If the absolute value in the test register is below the setpoint long enough to satisfy the pickup delay period, the alarm condition will be true. When the absolute value in the test register rises above the 021 Under Power Alarm dropout setpoint long enough to satisfy the dropout delay period, the alarm will dropout. Pickup and dropout setpoints are positive, delays are in seconds. The phase reversal alarm will occur whenever the phase voltage waveform rotation differs from the default phase rotation. The ABC phase rotation is assumed to be normal. If a CBA phase rotation is 051 Phase Reversal normal, the user should reprogram the power meter’s phase rotation ABC to CBA phase rotation. The pickup and dropout setpoints and delays for phase reversal do not apply. The phase loss voltage alarm will occur when any one or two phase voltages (but not all) fall to the pickup value and remain at or below the pickup value long enough to satisfy the specified pickup delay. When all 052 Phase Loss, Voltage of the phases remain at or above the dropout value for the dropout delay period, or when all of the phases drop below the specified phase loss pickup value, the alarm will dropout. Pickup and dropout setpoints are positive, delays are in seconds. The phase loss current alarm will occur when any one or two phase currents (but not all) fall to the pickup value and remain at or below the pickup value long enough to satisfy the specified pickup delay. When all 053 Phase Loss, Current of the phases remain at or above the dropout value for the dropout delay period, or when all of the phases drop below the specified phase loss pickup value, the alarm will dropout. Pickup and dropout setpoints are positive, delays are in seconds. The leading power factor alarm will occur when the test register value becomes more leading than the pickup setpoint (such as closer to 0.010) and remains more leading long enough to satisfy the pickup delay period. When the value becomes equal to or less leading than the dropout setpoint, that is 1.000, and remains less leading for the dropout 054 Leading Power Factor delay period, the alarm will dropout. Both the pickup setpoint and the dropout setpoint must be positive values representing leading power factor. Enter setpoints as integer values representing power factor in thousandths. For example, to define a dropout setpoint of 0.5, enter 500. Delays are in seconds. The lagging power factor alarm will occur when the test register value becomes more lagging than the pickup setpoint (such as closer to – 0.010) and remains more lagging long enough to satisfy the pickup delay period. When the value becomes equal to or less lagging than the dropout setpoint and remains less lagging for the dropout delay period, 055 Lagging Power Factor the alarm will dropout. Both the pickup setpoint and the dropout setpoint must be positive values representing lagging power factor. Enter setpoints as integer values representing power factor in thousandths. For example, to define a dropout setpoint of –0.5, enter 500. Delays are in seconds. © 2006 Schneider Electric. All Rights Reserved. 86 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 6—Basic Alarms Table 6–5: Alarm Types Type Description Operation Digital The digital input transition alarms will occur whenever the digital input changes from off to on. The alarm will dropout when the digital input 060 Digital Input On changes back to off from on. The pickup and dropout setpoints and delays do not apply. The digital input transition alarms will occur whenever the digital input changes from on to off.The alarm will dropout when the digital input 061 Digital Input Off changes back to on from off. The pickup and dropout setpoints and delays do not apply. This is a internal signal from the power meter and can be used, for 070 Unary example, to alarm at the end of an interval or when the power meter is reset. Neither the pickup and dropout delays nor the setpoints apply. Table 6–5: Default Alarm Configuration - Factory-enabled Alarms Pickup Dropout Alarm Pickup Dropout Standard Alarm Limit Time Limit Time No. Limit Limit Delay Delay 19 Voltage Unbalance L-N 20 (2.0%) 300 20 (2.0%) 300 20 Max. Voltage Unbalance L-L 20 (2.0%) 300 20 (2.0%) 300 End of Incremental Energy 53 00 0 0 Interval © 2006 Schneider Electric. All Rights Reserved. 87 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 6—Basic Alarms 6/2006 © 2006 Schneider Electric. All Rights Reserved. 88 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 7—Advanced Alarms CHAPTER 7—ADVANCED ALARMS This section describes the advanced alarm features found on the PM850 and the PM870. For information about basic alarm features, see Chapter 6—Basic Alarms on page73. Alarm Summary Table 7–1: Advanced alarm features by model Advanced Alarm Feature PM850 PM870 Boolean alarms 10 10 Disturbance alarms — 12 Alarm levels Yes Yes Custom alarms Yes Yes © 2006 Schneider Electric. All Rights Reserved. 89 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 7—Advanced Alarms 6/2006 Advanced Alarm Groups In addition to the basic alarm groups (see “Basic Alarm Groups” on page 74) the following advanced alarm groups are available. Boolean—Boolean alarms use Boolean logic to combine up to four enabled alarms. You can choose from the Boolean logic operands: AND, NAND, OR, NOR, or XOR to combine your alarms. Up to 10 alarms can be set up in this group. Disturbance (PM870)—Disturbance alarms have a detection rate of half a cycle and are useful for detecting voltage sags and swells. The Power Meter comes configured with 12 default voltage sag and swell alarms; current sag and swell alarms are available by configuring custom alarms. Up to 12 disturbance alarms can be set up in this group. For more information about disturbance monitoring, see Chapter 10—Disturbance Monitoring (PM870) on page109. Custom—The power meter has many pre-defined alarms, but you can also set up your own custom alarms using SMS. For example, you may need to alarm on a sag condition for current A. To create this type of custom alarm: 1. Select the appropriate alarm group (Disturbance in this case). 2. Delete any of the default alarms you are not using from the disturbance alarms group (for example, Sag Vbc). The Add button should be available now. 3. Click Add, then select Disturbance, Sag, and Current A. 4. Give the alarm a name. 5. Save the custom alarm. After creating a custom alarm, you can configure it by applying priorities, setting pickups and dropouts (if applicable), and so forth. SMS can be used to configure any of the advanced alarm types within the Series 800 Power Meter, but the Power Meter display cannot be used. Also, use SMS to delete an alarm and create a new alarm for evaluating other metered quantities. © 2006 Schneider Electric. All Rights Reserved. 90 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 7—Advanced Alarms Alarm Levels Using SMS with a PM850 or PM870, multiple alarms can be set up for one particular quantity (parameter) to create alarm “levels”. You can take different actions depending on the severity of the alarm. For example, you could set up two alarms for kW Demand. A default alarm already exists for kW Demand, but you could create another custom alarm for kW Demand, selecting different pickup points for it. The custom kW Demand alarm, once created, will appear in the standard alarm list. For illustration purposes, let’s set the default kW Demand alarm to 120 kW and the new custom alarm to 150 kW. One alarm named kW Demand ; the other kW Demand 150kW as shown in Figure 7–1. Note that if you choose to set up two alarms for the same quantity, use slightly different names to distinguish which alarm is active. The display can hold up to 15 characters for each name. You can create up to 10 alarm levels for each quantity. Figure 7–1: Two alarms set up for the same quantity with different pickup and dropout set points kW Demand 150 Alarm #43 Pick Up Alarm #43 Drop Out 140 130 Alarm #26 Pick Up 120 Alarm #26 Drop Out 100 Time Demand OK Approaching Peak Demand Below Peak Demand OK Peak Demand Exceeded Demand kW Demand (default) kW Demand 150 kW (custom) Alarm #26 kW Demand with pickup Alarm #43 kW Demand with pickup of 120 kWd, medium priority of 150 kWd, high priority © 2006 Schneider Electric. All Rights Reserved. 91 PLSD110156 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 7—Advanced Alarms 6/2006 Viewing Alarm Activity and History 1. Press ###: until ALARM is visible. 2. Press ALARM. �’���’�� �� 3. View the active alarm listed on the power meter display. If there are no active alarms, ����� ����� the screen reads, “NO ACTIVE ALARMS.” ��� ; 4. If there are active alarms, press <--or -- > to view a different alarm. ��� �"2= 5. Press HIST. �������� �K�5� 6. Press <-- or --> to view a different alarm’s history. �� ��� ��H ����’ 7. Press 1; to return to the SUMMARY screen. Alarm Conditions and Alarm Numbers This section lists the power meter’s predefined alarm conditions. For each alarm condition, the following information is provided. Alarm No.—a position number indicating where an alarm falls in the list. Alarm Description—a brief description of the alarm condition Abbreviated Display Name—an abbreviated name that describes the alarm condition, but is limited to 15 characters that fit in the window of the power meter’s display. Test Register—the register number that contains the value (where applicable) that is used as the basis for a comparison to alarm pickup and dropout settings. Units—the unit that applies to the pickup and dropout settings. Scale Group—the scale group that applies to the test register’s metering value (A–F). For a description of scale groups, see “Scale Factors” on page 81. Alarm Type—a reference to a definition that provides details on the operation and configuration of the alarm. For a description of advanced alarm types, refer to Table 7–3 on page 94. Table 7–2 on page 93 lists the preconfigured alarms by alarm number. © 2006 Schneider Electric. All Rights Reserved. 92 PLSD110258 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 7—Advanced Alarms Table 7–2: List of Default Disturbance Alarms by Alarm Number Alarm Abbreviated Test Scale Alarm Alarm Description Units ➀ ➁ Number Display Name Register Group Type Disturbance Monitoring (1/2 Cycle) (PM870) 41 Voltage Swell A Swell Van Volts D 080 42 Voltage Swell B Swell Vbn Volts D 080 43 Voltage Swell C Swell Vcn Volts D 080 44 Voltage Swell A–B Swell Vab Volts D 080 45 Voltage Swell B–C Swell Vbc Volts D 080 46 Voltage Swell C–A Swell Vca Volts D 080 47 Voltage Sag A–N Sag Van Volts D 080 48 Voltage Sag B–N Sag Vbn Volts D 080 49 Voltage Sag C–N Sag Vcn Volts D 080 50 Voltage Sag A–B Sag Vab Volts D 080 51 Voltage Sag B–C Sag Vbc Volts D 080 52 Voltage Sag C–A Sag Vca Volts D 080 ➀ Scale groups are described in Table 6–2 on page 82. ➁ Alarm types are described in Table 7–3 on page 94. NOTE: Current sag and swell alarms are enabled using SMS or by setting up custom alarms. To do this, delete any of the above default disturbance alarms, and then create a new current sag or swell alarm (see the example under the “Custom” alarm group on page 90.). Sag and swell alarms are available for all channels. © 2006 Schneider Electric. All Rights Reserved. 93 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 7—Advanced Alarms 6/2006 Table 7–3: Advanced Alarm Types Type Description Operation Boolean Logic The AND alarm will occur when all of the combined enabled alarms are AND 100 true (up to 4). The alarm will dropout when any of the enabled alarms drops out. Logic The NAND alarm will occur when any, but not all, or none of the NAND 101 combined enabled alarms are true. The alarm will dropout when all of the enabled alarms drop out, or all are true. Logic The OR alarm will occur when any of the combined enabled alarms are OR 102 true (up to 4). The alarm will dropout when all of the enabled alarms are false. Logic The NOR alarm will occur when none of the combined enabled alarms NOR 103 are true (up to 4). The alarm will dropout when any of the enabled alarms are true. Logic The XOR alarm will occur when only one of the combined enabled XOR 104 alarms is true (up to 4). The alarm will dropout when the enabled alarm drops out or when more than one alarm becomes true. Disturbance (PM870) The voltage swell alarms will occur whenever the continuous rms calculation is above the pickup setpoint and remains above the pickup setpoint for the specified number of cycles. When the continuous rms 080 Voltage Swell calculations fall below the dropout setpoint and remain below the setpoint for the specified number of cycles, the alarm will dropout. Pickup and dropout setpoints are positive and delays are in cycles. The voltage sag alarms will occur whenever the continuous rms calculation is below the pickup setpoint and remains below the pickup setpoint for the specified number of cycles. When the continuous rms 080 Voltage Sag calculations rise above the dropout setpoint and remain above the setpoint for the specified number of cycles, the alarm will drop out. Pickup and dropout setpoints are positive and delays are in cycles. © 2006 Schneider Electric. All Rights Reserved. 94 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 8—Logging CHAPTER 8—LOGGING Introduction This chapter briefly describes the following logs of the power meter: Alarm log Maintenance log Billing log User-defined data logs See the table below for a summary of logs supported by each power meter model. Table 8–1: Number of logs supported by model Number of Logs Per Model Log Type PM820 PM850 PM870 Alarm Log 1 1 1 Maintenance Log 1 1 1 Billing Log 1 1 1 Data Log 1 1 1 1 Data Log 2 — 1 1 Data Log 3 — 1 1 Logs are files stored in the nonvolatile memory of the power meter and are referred to as “onboard logs.” The amount of memory available depends on the model (see Table 8–2). Data and billing log files are preconfigured at the factory. You can accept the preconfigured logs or change them to meet your specific needs. Use SMS to set up and view all the logs. See the SMS online Help for information about working with the power meter’s onboard logs. Table 8–2: Available Memory for Onboard Logs Power Meter Model Total Memory Available PM820 80 KB PM850 800 KB PM870 800 KB Waveform captures are stored in the power meter’s memory, but they are not considered logs (see Chapter 9—Waveform Capture on page105). Refer to “Memory Allocation for Log Files” for information about memory allocation in the power meter. © 2006 Schneider Electric. All Rights Reserved. 95 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 8—Logging 6/2006 Memory Allocation for Log Files Each file in the power meter has a maximum memory size. Memory is not shared between the different logs, so reducing the number of values recorded in one log will not allow more values to be stored in a different log. The following table lists the memory allocated to each log: Table 8–3: Memory Allocation for Each Log Max. Records Max. Register Storage Power Meter Log Type Stored Values Recorded (Bytes) Model Alarm Log 100 11 2,200 All models Maintenance Log 40 4 320 All models PM820 Billing Log 5000 96 + 3 D/T 65,536 PM850 PM870 PM820 Data Log 1 5000 96 + 3 D/T 14,808 PM850 PM870 PM850 Data Log 2 5000 96 + 3 D/T 393,216 PM870 PM850 Data Log 3 5000 96 + 3 D/T 393,216 PM870 © 2006 Schneider Electric. All Rights Reserved. 96 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 8—Logging Alarm Log By default, the power meter can log the occurrence of any alarm condition. Each time an alarm occurs it is entered into the alarm log. The alarm log in the power meter stores the pickup and dropout points of alarms along with the date and time associated with these alarms. You select whether the alarm log saves data as first-in-first- out (FIFO) or fill and hold. With SMS, you can view and save the alarm log to disk, and reset the alarm log to clear the data out of the power meter’s memory. Alarm Log Storage The power meter stores alarm log data in nonvolatile memory. The size of the alarm log is fixed at 100 records. Maintenance Log The power meter stores a maintenance log in nonvolatile memory. The file has a fixed record length of four registers and a total of 40 records. The first register is a cumulative counter over the life of the power meter. The last three registers contain the date/time of when the log was updated. Table 8–4 describes the values stored in the maintenance log. These values are cumulative over the life of the power meter and cannot be reset. NOTE: Use SMS to view the maintenance log. Refer to the SMS online help for instructions. Table 8–4: Values Stored in the Maintenance Log Record Value Stored Number 1 Time stamp of the last change 2 Date and time of the last power failure 3 Date and time of the last firmware download 4 Date and time of the last option module change Date and time of the latest LVC update due to configuration errors 5 detected during meter initialization 6–11 Reserved 12 Date and time the Present Month Min/Max was last reset 13 Date and time the Previous Month Min/Max was last reset 14 Date and time the Energy Pulse Output was overdriven ➀ Additional outputs require option modules and are based on the I/O configuration of that particular module. © 2006 Schneider Electric. All Rights Reserved. 97 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 8—Logging 6/2006 Table 8–4: Values Stored in the Maintenance Log Record Value Stored Number 15 Date and time the Power Demand Min/Max was last reset 16 Date and time the Current Demand Min/Max was last reset 17 Date and time the Generic Demand Min/Max was last reset 18 Date and time the Input Demand Min/Max was last reset 19 Reserved 20 Date and time the Accumulated Energy value was last reset 21 Date and time the Conditional Energy value was last reset 22 Date and time the Incremental Energy value was last reset 23 Reserved 24 Date and time of the last Standard KY Output operation 25 Date and time of the last Discrete Output @A01 operation➀ 26 Date and time of the last Discrete Output @A02 operation➀ 27 Date and time of the last Discrete Output @A03 operation➀ 28 Date and time of the last Discrete Output @A04 operation➀ 29 Date and time of the last Discrete Output @A05 operation➀ 30 Date and time of the last Discrete Output @A06 operation➀ 31 Date and time of the last Discrete Output @A07 operation➀ 32 Date and time of the last Discrete Output @A08 operation➀ 33 Date and time of the last Discrete Output @B01 operation➀ 34 Date and time of the last Discrete Output @B02 operation➀ 35 Date and time of the last Discrete Output @B03 operation➀ 36 Date and time of the last Discrete Output @B04 operation➀ 37 Date and time of the last Discrete Output @B05 operation➀ 38 Date and time of the last Discrete Output @B06 operation➀ 39 Date and time of the last Discrete Output @B07 operation➀ 40 Date and time of the last Discrete Output @B08 operation➀ ➀ Additional outputs require option modules and are based on the I/O configuration of that particular module. © 2006 Schneider Electric. All Rights Reserved. 98 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 8—Logging Data Logs The PM820 records and stores readings at regularly scheduled intervals in one independent data log. The PM850 and PM870 record and store meter readings at regularly scheduled intervals in up to three independent data logs. Some data log files are preconfigured at the factory. You can accept the preconfigured data logs or change them to meet your specific needs. You can set up each data log to store the following information: Timed Interval—1 second to 24 hours for Data Log 1, and 1 minute to 24 hours for Data Logs 2 and 3 (how often the values are logged) First-In-First-Out (FIFO) or Fill and Hold Values to be logged—up to 96 registers along with the date and time of each log entry START/STOP Time—each log has the ability to start and stop at a certain time during the day The default registers for Data Log 1 are listed in Table 8–5 below. © 2006 Schneider Electric. All Rights Reserved. 99 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 8—Logging 6/2006 Table 8–5: Default Data Log 1 Register List Number of Description Data Type➀ Register Number Registers Start Date/Time 3 D/T Current D/T Current, Phase A 1 integer 1100 Current, Phase B 1 integer 1101 Current, Phase C 1 integer 1102 Current, Neutral 1 integer 1103 Voltage A-B 1 integer 1120 Voltage B-C 1 integer 1121 Voltage C-A 1 integer 1122 Voltage A-N 1 integer 1124 Voltage B-N 1 integer 1125 Voltage C-N 1 integer 1126 True Power Factor, Phase A 1 signed integer 1160 True Power Factor, Phase B 1 signed integer 1161 True Power Factor, Phase C 1 signed integer 1162 True Power Factor, Total 1 signed integer 1163 Last Demand, Current, 1 integer 2000 3-Phase Average Last Demand, Real Power, 1 integer 2150 3-Phase Total Last Demand, Reactive 1 integer 2165 Power, 3-Phase Total Last Demand, Apparent 1 integer 2180 Power 3-Phase Total ➀ Refer to Appendix A for more information about data types. Use SMS to clear each data log file, independently of the others, from the power meter’s memory. For instructions on setting up and clearing data log files, refer to the SMS online help file. © 2006 Schneider Electric. All Rights Reserved. 100 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 8—Logging Alarm-driven Data Log Entries The PM820, PM850, and PM870 can detect over 50 alarm conditions, including over/under conditions, digital input changes, phase unbalance conditions, and more. (See Chapter 6—Basic Alarms on page73 for more information.) Use SMS to assign each alarm condition one or more tasks, including forcing data log entries into one or more data log files. For example, assume you have defined three data log files. Using SMS, you could select an alarm condition such as “Overcurrent Phase A” and set up the power meter to force data log entries into any of the three log files each time the alarm condition occurs. Organizing Data Log Files (PM850, PM870) You can organize data log files in many ways. One possible way is to organize log files according to the logging interval. You might also define a log file for entries forced by alarm conditions. For example, you could set up three data log files as follows: Data Log 1: Log voltage every minute. Make the file large enough to hold 60 entries so that you could look back over the last hour’s voltage readings. Data Log 2: Log energy once every day. Make the file large enough to hold 31 entries so that you could look back over the last month and see daily energy use. Data Log 3: Report by exception. The report by exception file contains data log entries that are forced by the occurrence of an alarm condition. See the previous section “Alarm-driven Data Log Entries” for more information. NOTE: The same data log file can support both scheduled and alarm- driven entries. © 2006 Schneider Electric. All Rights Reserved. 101 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 8—Logging 6/2006 Billing Log The Power Meter stores a configurable billing log that updates every 10 to 1,440 minutes (the default interval 60 minutes). Data is stored by month, day, and the specified interval in minutes. The log contains 24 months of monthly data and 32 days of daily data, but because the maximum amount of memory for the billing log is 64 KB, the number of recorded intervals varies based on the number of registers recorded in the billing log. For example, using all of the registers listed in Table 8–6, the billing log holds 12 days of data at 60-minute intervals. This value is calculated by doing the following: 1. Calculate the total number of registers used (see Table 8–6 on page 103 for the number of registers). In this example, all 26 registers are used. 2. Calculate the number of bytes used for the 24 monthly records. 24 records (26 registers x 2 bytes/register) = 1,248 3. Calculate the number of bytes used for the 32 daily records. 32 (26 x 2) = 1,664 4. Calculate the number of bytes used each day. 96 (26 x 2) = 4,992 5. Calculate the number of days of 60-minute interval data recorded by subtracting the values from steps 2 and 3 from the total log file size of 65,536 bytes and then dividing by the value in step 4. (65,536 – 1,248 – 1,664) ÷ 4,992 = 12 days © 2006 Schneider Electric. All Rights Reserved. 102 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 8—Logging Table 8–6: Billing Log Register List Number of Description Data Type➀ Register Number Registers Start Date/Time 3 D/T Current D/T Real Energy In 4 MOD10L4 1700 Reactive Energy In 4 MOD10L4 1704 Real Energy Out 4 MOD10L4 1708 Reactive Energy Out 4 MOD10L4 1712 Apparent Energy Total 4 MOD10L4 1724 Total PF 1 INT16 1163 3P Real Power Demand 1 INT16 2151 3P Apparent Power Demand 1 INT16 2181 ➀ Refer to Appendix A for more information about data types. Configure the Billing Log Logging Interval The billing log can be configured to update every 10 to 1,440 minutes. The default logging interval is 60 minutes. To set the logging interval you can use SMS (see the SMS online Help for setup details) or you can use the power meter to write the logging interval to register 3085 (see “Read and Write Registers” on page 36). © 2006 Schneider Electric. All Rights Reserved. 103 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 8—Logging 6/2006 © 2006 Schneider Electric. All Rights Reserved. 104 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 9—Waveform Capture CHAPTER 9—WAVEFORM CAPTURE Introduction This section explains the waveform capture capabilities of the following Power Meter models: PM850 PM870 See Table 9–1 for a summary of waveform capture features. Table 9–1: Waveform capture summary by model Waveform Capture Feature PM850 PM870 Number of waveform captures 5 5 Waveform initiated: 9 9 Manually By alarm 9 9 Samples per cycle 128 Configurable* Channels (1 to 6) Configurable Configurable* Cycles 3 Configurable* Precycles 1 Configurable* * See Figure 9–1 on page 106. © 2006 Schneider Electric. All Rights Reserved. 105 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 9—Waveform Capture 6/2006 Waveform Capture A waveform capture can be initiated manually or by an alarm trigger to analyze steady-state or disturbance events. This waveform provides information about individual harmonics, which SMS calculates through the 63rd harmonic. It also calculates total harmonic distortion (THD) and other power quality parameters. NOTE: Disturbance waveform captures are available in the PM870 only. In the PM850, the waveform capture records five individual three-cycle captures at 128 samples per cycle simultaneously on all six metered channels (see “Channel Selection in SMS” on page 107). In the PM870, there is a range of one to five waveform captures, but the number of cycles captured varies based on the number of samples per cycle and the number of channels selected in SMS. Use Figure 9–1 to determine the number of cycles captured. Figure 9–1: PM870 Number of Cycles Captured 6 30 15 7 3 5 35 15 9 4 4 45 20 10 5 Number of 3 60 30 15 7 Channels 2 90 45 20 10 1 185 90 45 20 16 32 64 128 Number of Samples per Cycle NOTE: The number of cycles shown above are the total number of cycles allowed (pre-event cycles + event cycles = total cycles). © 2006 Schneider Electric. All Rights Reserved. 106 PLSD110333 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 9—Waveform Capture Initiating a Waveform Using SMS from a remote PC, initiate a waveform capture manually by selecting the power meter and issuing the acquire command. SMS will automatically retrieve the waveform capture from the power meter. You can display the waveform for all three phases, or zoom in on a single waveform, which includes a data block with extensive harmonic data. See the SMS online help for instructions. Waveform Storage The power meter can store multiple captured waveforms in its nonvolatile memory. The number of waveforms stored is based on the number selected. There are a maximum of five stored waveforms. All stored waveform data is retained on power-loss. Waveform Storage Modes There are two ways to store waveform captures: “FIFO” and “Fill and Hold.” FIFO mode allows the file to fill up the waveform capture file. After the file is full, the oldest waveform capture is removed, and the most recent waveform capture is added to the file. The Fill and Hold mode fills the file until the configured number of waveform captures is reached. New waveform captures cannot be added until the file is cleared. How the Power Meter Captures an Event When the power meter senses the trigger—that is, when the digital input transitions from OFF to ON, or an alarm condition is met—the power meter transfers the cycle data from its data buffer into the memory allocated for event captures. Channel Selection in SMS Using SMS, you can select up to six channels to include in the waveform capture. From the Waveform Capture dialog within SMS, select the check box(es) for the desired channel(s) and click OK, as shown in Figure 9–2. © 2006 Schneider Electric. All Rights Reserved. 107 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 9—Waveform Capture 6/2006 Figure 9–2: Channel Selection for Waveform Capture in SMS © 2006 Schneider Electric. All Rights Reserved. 108 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 10—Disturbance Monitoring (PM870) CHAPTER 10—DISTURBANCE MONITORING (PM870) This chapter gives you background information about disturbance monitoring and describes how to use the PM870 to continuously monitor for disturbances on the current and voltage inputs. It also provides an overview of using SMS to gather data when a disturbance event occurs. About Disturbance Monitoring Momentary voltage disturbances are an increasing concern for industrial plants, hospitals, data centers, and other commercial facilities because modern equipment used in those facilities tends to be more sensitive to voltage sags, swells, and momentary interruptions. The power meter can detect these events by continuously monitoring and recording current and voltage information on all metered channels. Using this information, you can diagnose equipment problems resulting from voltage sags or swells and identify areas of vulnerability, enabling you to take corrective action. The interruption of an industrial process because of an abnormal voltage condition can result in substantial costs, which manifest themselves in many ways: labor costs for cleanup and restart lost productivity damaged product or reduced product quality delivery delays and user dissatisfaction The entire process can depend on the sensitivity of a single piece of equipment. Relays, contactors, adjustable speed drives, programmable controllers, PCs, and data communication networks are all susceptible to power quality problems. After the electrical system is interrupted or shut down, determining the cause may be difficult. Several types of voltage disturbances are possible, each potentially having a different origin and requiring a separate solution. A momentary interruption occurs when a protective device interrupts the circuit that feeds a facility. Swells and overvoltages can damage equipment or cause motors to overheat. Perhaps the biggest power quality problem is the momentary voltage sag caused by faults on remote circuits. © 2006 Schneider Electric. All Rights Reserved. 109 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 10—Disturbance Monitoring (PM870) 6/2006 A voltage sag is a brief (1/2 cycle to 1 minute) decrease in rms voltage magnitude. A sag is typically caused by a remote fault somewhere on the power system, often initiated by a lightning strike. In Figure 10–1, the utility circuit breaker cleared the fault near plant D. The fault not only caused an interruption to plant D, but also resulted in voltage sags to plants A, B, and C. NOTE: The PM870 is able to detect sag and swell events less than 1/2 cycle duration. However, it may be impractical to have setpoints more sensitive than 10% for voltage and current fluctuations. Figure 10–1: A fault can cause a voltage sag on the whole system Utility Circuit Breakers with Reclosers 1 Plant A Utility 2 Plant B Transformer 3 Plant C 4 Plant D X Fault A fault near plant D, cleared by the utility circuit breaker, can still affect plants A, B, and C, resulting in a voltage sag. System voltage sags are much more numerous than interruptions, since a wider part of the distribution system is affected. And, if reclosers are operating, they may cause repeated sags. The PM870 can record recloser sequences, too. The waveform in Figure 10–2 shows the magnitude of a voltage sag, which persists until the remote fault is cleared. © 2006 Schneider Electric. All Rights Reserved. 110 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 10—Disturbance Monitoring (PM870) Figure 10–2: Waveform showing voltage sag caused by a remote fault and lasted five cycles With the information obtained from the PM870 during a disturbance, you can solve disturbance-related problems, including the following: Obtain accurate measurement from your power system — Identify the number of sags, swells, or interruptions for evaluation — Accurately distinguish between sags and interruptions, with accurate recording of the time and date of the occurrence — Provide accurate data in equipment specification (ride- through, etc.) Determine equipment sensitivity — Compare equipment sensitivity of different brands (contactor dropout, drive sensitivity, etc.) — Diagnose mysterious events such as equipment malfunctions, contactor dropout, computer glitches, etc. — Compare actual sensitivity of equipment to published standards — Use waveform capture to determine exact disturbance characteristics to compare with equipment sensitivity — Justify purchase of power conditioning equipment — Distinguish between equipment malfunctions and power system related problems © 2006 Schneider Electric. All Rights Reserved. 111 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 10—Disturbance Monitoring (PM870) 6/2006 Develop disturbance prevention methods — Develop solutions to voltage sensitivity-based problems using actual data Work with the utility — Discuss protection practices with the serving utility and negotiate suitable changes to shorten the duration of potential sags (reduce interruption time delays on protective devices) — Work with the utility to provide alternate “stiffer” services (alternate design practices) © 2006 Schneider Electric. All Rights Reserved. 112 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 10—Disturbance Monitoring (PM870) Capabilities of the PM870 During an Event The PM870 calculates rms magnitudes, based on 128 data points per cycle, every 1/2 cycle. This ensures that even sub-cycle duration rms variations are not missed. The power meter is configured with 12 default voltage disturbance alarms for all voltage channels. Current sag and swell alarms are available by configuring custom alarms. A maximum of 12 disturbance alarms are available. When the PM870 detects a sag or swell, it can perform the following actions: Perform a waveform capture with a resolution from 185 cycles at 16 samples per cycle on one channel down to 3 cycles at 128 samples per cycle on all six channels of the metered current and voltage inputs (see Figure 9–1 on page 106). Use SMS to setup the event capture and retrieve the waveform. Record the event in the alarm log. When an event occurs, the PM870 updates the alarm log with an event date and time stamp with 1 millisecond resolution for a sag or swell pickup, and an rms magnitude corresponding to the most extreme value of the sag or swell during the event pickup delay. Also, the PM870 can record the sag or swell dropout in the alarm log at the end of the disturbance. Information stored includes: a dropout time stamp with 1 millisecond resolution and a second rms magnitude corresponding to the most extreme value of the sag or swell. Use SMS to view the alarm log. NOTE: The Power Meter display has a 1 second resolution. Force a data log entry in up to 3 independent data logs. Use SMS to set up and view the data logs. Operate any output relays when the event is detected. Indicate the alarm on the display by flashing the maintenance icon to show that a sag or swell event has occurred. © 2006 Schneider Electric. All Rights Reserved. 113 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 10—Disturbance Monitoring (PM870) 6/2006 Using the Power Meter with SMS to Perform Disturbance Monitoring This section gives you an overview of the steps to set up the power meter for disturbance monitoring. For detailed instructions, see the SMS online Help. In SMS under Setup > Devices > Routing, select the device. The Device Setup dialog box contains the tabs for setting up disturbance monitoring. After you have performed basic set up of the power meter, perform three setup steps: 1. Using the Onboard Files tab in SMS, select Enable in the Log Files section. This activates the Waveform Event Capture section. 2. Fill in the Waveform Event Capture section using values from the chart in Figure 9–1 on page 106. 3. Using the Onboard Alarms/Events tab, do the following: a. Select one of the Disturbance alarms in the Alarms list box. b. Configure the Alarm Setpoints/Delays section. c. Select the Data Logs and WFC. d. Click the Outputs button, then configure the relay outputs. e. Select Enable to enable the Disturbance alarm. NOTE: To enable current sag and swell alarms, see “Custom” in “Advanced Alarm Groups” on page 90 © 2006 Schneider Electric. All Rights Reserved. 114 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 11—Maintenance and Troubleshooting CHAPTER 11—MAINTENANCE AND TROUBLESHOOTING Introduction This chapter describes information related to maintenance of your power meter. The power meter does not contain any user-serviceable parts. If the power meter requires service, contact your local sales representative. Do not open the power meter. Opening the power meter voids the warranty. DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Do not attempt to service the pow er meter. CT and PT inputs may contain hazardous currents and voltages. Only authorized service personnel from the manufacturer should service the power meter. Failure to follow this instruction will result in death or serious injury. CAUTION HAZARD OF EQUIPMENT DAMAGE Do not perform a Dielectric (Hi-Po t) or Megger test on the power meter. High voltage testing of the power meter may damage the unit. Before performing Hi-Pot or Megger testing on any equipment in which the power meter is installed, disconnect all input and output wires to the power meter. Failure to follow this instruction can result in injury or equipment damage. © 2006 Schneider Electric. All Rights Reserved. 115 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 11—Maintenance and Troubleshooting 6/2006 Power Meter Memory The power meter uses its nonvolatile memory (RAM) to retain all data and metering configuration values. Under the operating temperature range specified for the power meter, this nonvolatile memory has an expected life of up to 100 years. The power meter stores its data logs on a memory chip, which has a life expectancy of up to 20 years under the operating temperature range specified for the power meter. The life of the internal battery-backed clock is over 10 years at 25°C. NOTE: Life expectancy is a function of operating conditions; this does not constitute any expressed or implied warranty. Identifying the Firmware Version, Model, and Serial Number 1. From the first menu level, press ###: until MAINT is visible. ��������0� 2. Press DIAG. 3. Press METER. ��� ��� ����- 4. View the model, firmware (OS) version, ��’ ������ ���� and serial number. 5. Press 1; to return to the MAINTENANCE ��’ ������ ����� screen. �������� ���� �� �� �H Viewing the Display in Different Languages The power meter can be set to use one of three different languages: English, French, and Spanish. Other languages are available. Please contact your local sales representative for more information about other language options. The power meter language can be selected by doing the following: © 2006 Schneider Electric. All Rights Reserved. 116 PLSD110094c ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 11—Maintenance and Troubleshooting 1. From the first menu level, press ###: until MAINT is visible. -��.��.� 2. Press MAINT. 3. Press SETUP. ��.-� 4. Enter your password, then press OK. 5. Press ###: until LANG is visible. 6. Press LANG. 7. Select the language: ENGL (English), SPAN (Spanish), FREN (French), GERMN �� �� � � (German), or RUSSN (Russian). 8. Press OK. 9. Press1;. 10. Press YES to save your changes. Technical Support Please refer to the Technical Support Contacts provided in the power meter shipping carton for a list of support phone numbers by country. © 2006 Schneider Electric. All Rights Reserved. 117 PLSD110103 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 11—Maintenance and Troubleshooting 6/2006 Troubleshooting The information in Table 11–1 on page 119 describes potential problems and their possible causes. It also describes checks you can perform or possible solutions for each. After referring to this table, if you cannot resolve the problem, contact the your local Square D/Schneider Electric sales representative for assistance. DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Apply appropriate pe rsonal protective equipment (PPE) and follow safe electrical practices. For example, in the United States, see NFPA 70E. This equipment must be installed and serviced only by qualified personnel. Turn off all power supplying this equipment before working on or inside. Always use a properly rated voltage sensing device to confirm that all power is off. Carefully inspect the work area for tools and objects that may have been left inside the equipment. Use caution while removing or installing panels so that they do not extend into the energized bus; avoid handling the panels, which could cause personal injury. Failure to follow this instruction will result in death or serious injury. © 2006 Schneider Electric. All Rights Reserved. 118 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Chapter 11—Maintenance and Troubleshooting Heartbeat LED The heartbeat LED helps to troubleshoot the power meter. The LED works as follows: Normal operation — the LED flashes at a steady rate during normal operation. Communications — the LED flash rate changes as the communications port transmits and receives data. If the LED flash rate does not change when data is sent from the host computer, the power meter is not receiving requests from the host computer. Hardware — if the heartbeat LED remains lit and does not flash ON and OFF, there is a hardware problem. Do a hard reset of the power meter (turn OFF power to the power meter, then restore power to the power meter). If the heartbeat LED remains lit, contact your local sales representative. Control power and display — if the heartbeat LED flashes, but the display is blank, the display is not functioning properly. If the display is blank and the LED is not lit, verify that control power is connected to the power meter. Table 11–1: Troubleshooting Potential Problem Possible Cause Possible Solution When the maintenance icon is illuminated, go to DIAGNOSTICS > MAINTENANCE. When the maintenance icon is The maintenance icon is Error messages display to indicate the illuminated, it indicates a potential illuminated on the power reason the icon is illuminated. Note these hardware or firmware problem in the meter display. error messages and call Technical Support power meter. or contact your local sales representative for assistance. Verify that the power meter line (L) and The display is blank after neutral (N) terminals (terminals 25 and applying control power to The power meter may not be 27) are receiving the necessary power. the power meter. receiving the necessary power.Verify that the heartbeat LED is blinking. Check the PLSD110074. © 2006 Schneider Electric. All Rights Reserved. 119 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Chapter 11—Maintenance and Troubleshooting 6/2006 Table 11–1: Troubleshooting Potential Problem Possible Cause Possible Solution Verify that the power meter is grounded as Power meter is grounded incorrectly. described in “Grounding the Power Meter” in the installation manual. Check that the correct values have been entered for power meter setup parameters (CT and PT ratings, System Type, Nominal Incorrect setup values. Frequency, and so on). See “Set Up the Power Meter” on page 16 for setup The data being displayed is instructions. inaccurate or not what you Check power meter voltage input terminals expect. Incorrect voltage inputs. L (8, 9, 10, 11) to verify that adequate voltage is present. Check that all CTs and PTs are connected correctly (proper polarity is observed) and that they are energized. Check shorting Power meter is wired improperly. terminals. See Chapter 4 — Wiring in the installation manual. Initiate a wiring check using SMS. Check to see that the power meter is correctly addressed. See “Power Meter Power meter address is incorrect. With Integrated Display Communications Setup” on page 17 for instructions. Verify that the baud rate of the power meter matches the baud rate of all other devices on its communications link. See Power meter baud rate is incorrect. “Power Meter With Integrated Display Communications Setup” on page 17 for instructions. Cannot communicate with Verify the power meter communications power meter from a remote Communications lines are improperly connections. Refer to Chapter 5 — personal computer. connected. Communications in the installation manual for instructions. Check to see that a multipoint communications terminator is properly Communications lines are improperly installed. See “Terminating the terminated. Communications Link” on page 28 in the installation manual for instructions. Check the route statement. Refer to the Incorrect route statement to power SMS online help for instructions on meter. defining route statements. © 2006 Schneider Electric. All Rights Reserved. 120 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List APPENDIX A—POWER METER REGISTER LIST About Registers The four tables in this appendix contain an abbreviated listing of power meter registers. For registers defined in bits, the rightmost bit is referred to as bit 00. Figure A–1 shows how bits are organized in a register. Figure A–1: Bits in a register High Byte Low Byte 0 0 000010 0 010 0 100 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 Bit No. 00 The power meter registers can be used with MODBUS or JBUS protocols. Although the MODBUS protocol uses a zero-based register addressing convention and JBUS protocol uses a one-based register addressing convention, the power meter automatically compensates for the MODBUS offset of one. Regard all registers as holding registers where a 30,000 or 40,000 offset can be used. For example, Current Phase A will reside in register 31,100 or 41,100 instead of 1,100 as listed in Table A–3 on page 124. Floating-point Registers Floating-point registers are also available. See Table A–7 on page 183 for an abbreviated list of floating-point registers. To enable floating-point registers, see “Enabling Floating-point Registers” on page 220. © 2006 Schneider Electric All Rights Reserved 121 PLSD110174 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 How Power Factor is Stored in the Register Each power factor value occupies one register. Power factor values are stored using signed magnitude notation (see Figure A–2 below). Bit number 15, the sign bit, indicates leading/lagging. A positive value (bit 15=0) always indicates leading. A negative value (bit 15=1) always indicates lagging. Bits 0–9 store a value in the range 0–1,000 decimal. For example the power meter would return a leading power factor of 0.5 as 500. Divide by 1,000 to get a power factor in the range 0 to 1.000. Figure A–2: Power factor 15 14 13 12 11 10 9 8 7 6 5 4 3 2 10 00000 Unused Bits Power Factor Sign Bit Set to 0 0=Leading in the range 100-1000 (thousandths) 1=Lagging When the power factor is lagging, the power meter returns a high negative value—for example, -31,794. This happens because bit 15=1 (for example, the binary equivalent of -31,794 is 1000001111001110). To get a value in the range 0 to 1,000, you need to mask bit 15. You do this by adding 32,768 to the value. An example will help clarify. Assume that you read a power factor value of -31,794. Convert this to a power factor in the range 0 to 1.000, as follows: -31,794 + 32,768 = 974 974/1,000 = .974 lagging power factor © 2006 Schneider Electric All Rights Reserved 122 P SD110168 L ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List How Date and Time are Stored in Registers The date and time are stored in a three-register compressed format. Each of the three registers, such as registers 1810 to 1812, contain a high and low byte value to represent the date and time in hexadecimal. Table A–1 lists the register and the portion of the date or time it represents. Table A–1: Date and Time Format Register Hi Byte Lo Byte Register 0 Month (1-12) Day (1-31) Register 1 Year (0-199) Hour (0-23) Register 2 Minute (0-59) Second (0-59) For example, if the date was 01/25/00 at 11:06:59, the Hex value would be 0119, 640B, 063B. Breaking it down into bytes we have the following: NOTE: Date format is a 3 (6-byte) register compressed format. (Year 2001 is represented as 101 in the year byte.) Table A–2: Date and Time Byte Example Hexadecimal Value Hi Byte Lo Byte 0119 01 = month 19 = day 640B 64 = year 0B = hour 063B 06 = minute 3B = seconds © 2006 Schneider Electric All Rights Reserved 123 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Register List Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes 1s Metering 1s Metering — Current 1100 Current, Phase A A Amps/Scale 0 – 32,767 RMS 1101 Current, Phase B A Amps/Scale 0 – 32,767 RMS 1102 Current, Phase C A Amps/Scale 0 – 32,767 RMS 0 – 32,767 1103 Current, Neutral B Amps/Scale RMS (4-wire system only) (-32,768 if N/A) Current, 3-Phase 1105 A Amps/Scale 0 – 32,767 Calculated mean of Phases A, B & C Average Current, Unbalance, 1107 — 0.10% 0 – 1,000 Phase A Current, Unbalance, 1108 — 0.10% 0 – 1,000 Phase B Current, Unbalance, 1109 — 0.10% 0 – 1,000 Phase C Current, Unbalance, 1110 — 0.10% 0 – 1,000 Percent Unbalance, Worst Max 1s Metering — Voltage 1120 Voltage, A-B D Volts/Scale 0 – 32,767 RMS Voltage measured between A & B 1121 Voltage, B-C D Volts/Scale 0 – 32,767 RMS Voltage measured between B & C 1122 Voltage, C-A D Volts/Scale 0 – 32,767 RMS Voltage measured between C & A 1123 Voltage, L-L Average D Volts/Scale 0 – 32,767 RMS 3 Phase Average L-L Voltage 0 – 32,767 RMS Voltage measured between A & N 1124 Voltage, A-N D Volts/Scale (-32,768 if N/A) 4-wire system, system 10, and system 12 0 – 32,767 RMS Voltage measured between B & N 1125 Voltage, B-N D Volts/Scale (-32,768 if N/A) 4-wire system and system 12 0 – 32,767 RMS Voltage measured between C & N 1126 Voltage, C-N D Volts/Scale (-32,768 if N/A) 4-wire system only RMS Voltage measured between N & meter 0 – 32,767 reference 1127 Voltage, N-R E Volts/Scale (-32,768 if N/A) 4-wire system with 4 element metering only RMS 3-Phase Average L-N Voltage (2-phase 1128 Voltage, L-N Average D Volts/Scale 0 – 32,767 average for system 12) Voltage, Unbalance, A- 1129 — 0.10% 0 – 1,000 Percent Voltage Unbalance, Phase A-B B Voltage, Unbalance, B- 1130 — 0.10% 0 – 1,000 Percent Voltage Unbalance, Phase B-C C Voltage, Unbalance, C- 1131 — 0.10% 0 – 1,000 Percent Voltage Unbalance, Phase C-A A Voltage, Unbalance, 1132 — 0.10% 0 – 1,000 Percent Voltage Unbalance, Worst L-L Max L-L © 2006 Schneider Electric All Rights Reserved 124 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes 0 – 1,000 Percent Voltage Unbalance, Phase A-N Voltage, Unbalance, A- 1133 — 0.10% N (-32,768 if N/A) 4-wire system only 0 – 1,000 Percent Voltage Unbalance, Phase B-N Voltage, Unbalance, B- 1134 — 0.10% N (-32,768 if N/A) 4-wire system only 0 – 1,000 Percent Voltage Unbalance, Phase C-N Voltage, Unbalance, C- 1135 — 0.10% N (-32,768 if N/A) 4-wire system only 0 – 1,000 Percent Voltage Unbalance, Worst L-N Voltage, Unbalance, 1136 — 0.10% Max L-N (-32,768 if N/A) 4-wire system only 1s Metering — Power -32,767 – 32,767 Real Power (PA) 1140 Real Power, Phase A F kW/Scale (-32,768 if N/A) 4-wire system only -32,767 – 32,767 Real Power (PB) 1141 Real Power, Phase B F kW/Scale (-32,768 if N/A) 4-wire system only -32,767 – 32,767 Real Power (PC) 1142 Real Power, Phase C F kW/Scale (-32,768 if N/A) 4-wire system only 4-wire system = PA+PB+PC 1143 Real Power, Total F kW/Scale -32,767 – 32,767 3-wire system = 3-Phase real power -32,767 – 32,767 Reactive Power (QA) Reactive Power, Phase 1144 F kVAr/Scale A (-32,768 if N/A) 4-wire system only -32,767 – 32,767 Reactive Power (QB) Reactive Power, Phase 1145 F kVAr/Scale B (-32,768 if N/A) 4-wire system only -32,767 – 32,767 Reactive Power (QC) Reactive Power, Phase 1146 F kVAr/Scale C (-32,768 if N/A) 4-wire system only 4-wire system = QA+QB+QC 1147 Reactive Power, Total F kVAr/Scale -32,767 – 32,767 3 wire system = 3-Phase reactive power -32,767 – 32,767 Apparent Power (SA) Apparent Power, 1148 F kVA/Scale Phase A (-32,768 if N/A) 4-wire system only -32,767 – 32,767 Apparent Power (SB) Apparent Power, 1149 F kVA/Scale Phase B (-32,768 if N/A) 4-wire system only -32,767 – 32,767 Apparent Power (SC) Apparent Power, 1150 F kVA/Scale Phase C (-32,768 if N/A) 4-wire system only 4-wire system = SA+SB+SC 1151 Apparent Power, Total F kVA/Scale -32,767 – 32,767 3-wire system = 3-Phase apparent power 1s Metering — Power Factor -0.002 to 1.000 Derived using the complete harmonic content True Power Factor, to +0.002 of real and apparent power. 1160 — 0.001 Phase A (-32,768 if N/A) 4-wire system only -0.002 to 1.000 Derived using the complete harmonic content True Power Factor, to +0.002 of real and apparent power. 1161 — 0.001 Phase B (-32,768 if N/A) 4-wire system only © 2006 Schneider Electric All Rights Reserved 125 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes -0.002 to 1.000 Derived using the complete harmonic content True Power Factor, to +0.002 of real and apparent power. 1162 — 0.001 Phase C (-32,768 if N/A) 4-wire system only -0.002 to 1.000 True Power Factor, Derived using the complete harmonic content to +0.002 1163 — 0.001 Total of real and apparent power (-32,768 if N/A) Derived using the complete harmonic content of real and apparent power (4-wire system 0 – 2,000 Alternate True Power only). The reported value is mapped from 0- 1164 — 0.001 Factor, Phase A 2000, with 1000 representing unity, values (-32,768 if N/A) below 1000 representing lagging, and values above 1000 representing leading. Derived using the complete harmonic content of real and apparent power (4-wire system only). The reported value is mapped from 0- 0 – 2,000 Alternate True Power 2000, with 1000 representing unity, values 1165 — 0.001 Factor, Phase B (-32,768 if N/A) below 1000 representing lagging, and values above 1000 representing leading . Derived using the complete harmonic content of real and apparent power (4-wire system 0 – 2,000 Alternate True Power only). The reported value is mapped from 0- 1166 — 0.001 Factor, Phase C 2000, with 1000 representing unity, values (-32,768 if N/A) below 1000 representing lagging, and values above 1000 representing leading. Derived using the complete harmonic content of real and apparent power. The reported value Alternate True Power 1167 — 0.001 0 – 2,000 is mapped from 0-2000, with 1000 representing Factor, Total unity, values below 1000 representing lagging, and values above 1000 representing leading. -0.002 to 1.000 Derived using only fundamental frequency of Displacement Power to +0.002 the real and apparent power. 1168 — 0.001 Factor, Phase A (-32,768 if N/A) 4-wire system only -0.002 to 1.000 Derived using only fundamental frequency of Displacement Power to +0.002 the real and apparent power. 1169 — 0.001 Factor, Phase B (-32,768 if N/A) 4-wire system only -0.002 to 1.000 Derived using only fundamental frequency of Displacement Power to +0.002 the real and apparent power. 1170 — 0.001 Factor, Phase C (-32,768 if N/A) 4-wire system only -0.002 to 1.000 Displacement Power Derived using only fundamental frequency of to +0.002 1171 — 0.001 Factor, Total the real and apparent power (-32,768 if N/A) Derived using only fundamental frequency of the real and apparent power (4-wire system 0 – 2,000 Alternate Displacement only). The reported value is mapped from 0- 1172 — 0.001 Power Factor, Phase A 2000, with 1000 representing unity, values (-32,768 if N/A) below 1000 representing lagging, and values above 1000 representing leading. © 2006 Schneider Electric All Rights Reserved 126 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Derived using only fundamental frequency of the real and apparent power (4-wire system 0 – 2,000 Alternate Displacement only). The reported value is mapped from 0- 1173 — 0.001 Power Factor, Phase B 2000, with 1000 representing unity, values (-32,768 if N/A) below 1000 representing lagging, and values above 1000 representing leading. Derived using only fundamental frequency of the real and apparent power (4-wire system 0 – 2,000 Alternate Displacement only). The reported value is mapped from 0- 1174 — 0.001 Power Factor, Phase C 2000, with 1000 representing unity, values (-32,768 if N/A) below 1000 representing lagging, and values above 1000 representing leading. Derived using only fundamental frequency of the real and apparent power. The reported Alternate Displacement value is mapped from 0-2000, with 1000 1175 — 0.001 0 – 2,000 Power Factor, Total representing unity, values below 1000 representing lagging, and values above 1000 representing leading. 1s Metering — Frequency (50/60Hz) Frequency of circuits being monitored. If the 0.01Hz 2,300 – 6,700 frequency is out of range, the register is - 32,768. 1180 Frequency — (400Hz) 0.10Hz 3,500 – 4,500 (-32,768 if N/A) Power Quality THD Total Harmonic Distortion, Phase A Current THD/thd Current, 1200 — 0.10% 0 – 32,767 Phase A See register 3227 for THD/ thd definition Total Harmonic Distortion, Phase B Current THD/thd Current, 1201 — 0.10% 0 – 32,767 Phase B See register 3227 for THD/ thd definition Total Harmonic Distortion, Phase C Current THD/thd Current, 1202 — 0.10% 0 – 32,767 Phase C See register 3227 for THD/ thd definition Total Harmonic Distortion, Phase N Current 0 – 32,767 THD/thd Current, 1203 — 0.10% (4-wire system only) Phase N (-32,768 if N/A) See register 3227 for THD/ thd definition Total Harmonic Distortion Phase A-N 0 – 32,767 THD/thd Voltage, 1207 — 0.10% (4-wire system only) Phase A-N (-32,768 if N/A) See register 3227 for THD/ thd definition Total Harmonic Distortion Phase B-N 0 – 32,767 THD/thd Voltage, 1208 — 0.10% (4-wire system only) Phase B-N (-32,768 if N/A) See register 3227 for THD/ thd definition Total Harmonic Distortion Phase C-N 0 – 32,767 THD/thd Voltage, 1209 — 0.10% (4-wire system only) Phase C-N (-32,768 if N/A) See register 3227 for THD/ thd definition © 2006 Schneider Electric All Rights Reserved 127 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Total Harmonic Distortion Phase A-B THD/thd Voltage, 1211 — 0.10% 0 – 32,767 Phase A-B See register 3227 for THD/ thd definition Total Harmonic Distortion Phase B-C THD/thd Voltage, 1212 — 0.10% 0 – 32,767 Phase B-C See register 3227 for THD/ thd definition Total Harmonic Distortion Phase C-A THD/thd Voltage, 1213 — 0.10% 0 – 32,767 Phase C-A See register 3227 for THD/ thd definition Fundamental Magnitudes and Angles Current Current Fundamental 1230 RMS Magnitude, A Amps/Scale 0 – 32,767 Phase A Current Fundamental 1231 Coincident Angle, — 0.1° 0 – 3,599 Referenced to A-N/A-B Voltage Angle Phase A Current Fundamental 1232 RMS Magnitude, A Amps/Scale 0 – 32,767 Phase B Current Fundamental 1233 Coincident Angle, — 0.1° 0 – 3,599 Referenced to A-N/A-B Voltage Angle Phase B Current Fundamental 1234 RMS Magnitude, A Amps/Scale 0 – 32,767 Phase C Current Fundamental 1235 Coincident Angle, — 0.1° 0 – 3,599 Referenced to A-N/A-B Voltage Angle Phase C Current Fundamental 0 – 32,767 1236 RMS Magnitude, B Amps/Scale 4-wire system only (-32,768 if N/A) Neutral Current Fundamental 0 – 3,599 Referenced to A-N 1237 Coincident Angle, — 0.1° (-32,768 if N/A) 4-wire system only Neutral Voltage Voltage Fundamental Voltage A-N (4-wire system) 1244 RMS Magnitude, A- D Volts/Scale 0 – 32,767 Voltage A-B (3-wire system) N/A-B Voltage Fundamental 1245 Coincident Angle, A- — 0.1° 0 – 3,599 Referenced to A-N (4-wire) or A-B (3-wire) N/A-B Voltage Fundamental Voltage B-N (4-wire system) 1246 RMS Magnitude, B- D Volts/Scale 0 – 32,767 Voltage B-C (3-wire system) N/B-C Voltage Fundamental 1247 Coincident Angle, B- — 0.1° 0 – 3,599 Referenced to A-N (4-wire) or A-B (3-wire) N/B-C Voltage Fundamental Voltage C-N (4-wire system) 1248 RMS Magnitude, C- D Volts/Scale 0 – 32,767 Voltage C-A (3-wire system) N/C-A © 2006 Schneider Electric All Rights Reserved 128 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Voltage Fundamental 1249 Coincident Angle, C- — 0.1° 0 – 3,599 Referenced to A-N (4-wire) or A-B (3-wire) N/C-A Sequence Components Current, Positive 1284 A Amps/Scale 0 – 32,767 Sequence, Magnitude Current, Positive Sequence, 1285 — 0.1 0 – 3,599 Angle Current, Negative 1286 A Amps/Scale 0 – 32,767 Sequence, Magnitude Current, Negative Sequence, 1287 — 0.1 0 – 3,599 Angle Current, Zero 1288 A Amps/Scale 0 – 32,767 Sequence, Magnitude Current, Zero Sequence, 1289 — 0.1 0 – 3,599 Angle Voltage, Positive 1290 D Volts/Scale 0 – 32,767 Sequence, Magnitude Voltage, Positive Sequence, 1291 — 0.1 0 – 3,599 Angle Voltage, Negative 1292 D Volts/Scale 0 – 32,767 Sequence, Magnitude Voltage, Negative Sequence, 1293 — 0.1 0 – 3,599 Angle Voltage, Zero 1294 D Volts/Scale 0 – 32,767 Sequence, Magnitude Voltage, Zero Sequence, 1295 — 0.1 0 – 3,599 Angle Current, Sequence, 1296 — 0.10% 0 – 10,000 Unbalance Voltage, Sequence, 1297 — 0.10% 0 – 10,000 Unbalance Current, Sequence 1298 — 0.10% 0 – 10,000 Negative Sequence / Positive Sequence Unbalance Factor Voltage, Sequence 1299 — 0.10% 0 – 10,000 Negative Sequence / Positive Sequence Unbalance Factor © 2006 Schneider Electric All Rights Reserved 129 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Minimum/Maximum Present Month Min/Max Group 1 See “Minimum/Maximum Template” on 1300 Min/Max Voltage L-L — — — page 131 See “Minimum/Maximum Template” on 1310 Min/Max Voltage L-N — — — page 131 See “Minimum/Maximum Template” on 1320 Min/Max Current — — — page 131 Min/Max Voltage L-L, See “Minimum/Maximum Template” on 1330 — — — Unbalance page 131 Min/Max Voltage L-N See “Minimum/Maximum Template” on 1340 — — — Unbalance page 131 Min/Max True Power See “Minimum/Maximum Template” on 1350 — — — Factor Total page 131 Min/Max Displacement See “Minimum/Maximum Template” on Power Factor 1360 — — — page 131 Total Min/Max Real Power See “Minimum/Maximum Template” on 1370 — — — Total page 131 Min/Max Reactive See “Minimum/Maximum Template” on 1380 — — — Power Total page 131 Min/Max Apparent See “Minimum/Maximum Template” on 1390 — — — Power Total page 131 Min/Max THD/thd See “Minimum/Maximum Template” on 1400 — — — Voltage L-L page 131 Min/Max THD/thd See “Minimum/Maximum Template” on 1410 — — — Voltage L-N page 131 Min/Max THD/thd See “Minimum/Maximum Template” on 1420 — — — Current page 131 See “Minimum/Maximum Template” on 1430 Min/Max Frequency — — — page 131 Date/Time of last See See Table A–1 Date/Time of last Present Month Min/Max 1440 Present Month — Table A–1 on page 123 Update Min/Max Update on page 123 Previous Month Min/Max Group 1 See “Minimum/Maximum Template” on 1450 Min/Max Voltage L-L — — — page 131 See “Minimum/Maximum Template” on 1460 Min/Max Voltage L-N — — — page 131 See “Minimum/Maximum Template” on 1470 Min/Max Current — — — page 131 Min/Max Voltage L-L, See “Minimum/Maximum Template” on 1480 — — — Unbalance page 131 Min/Max Voltage L-N See “Minimum/Maximum Template” on 1490 — — — Unbalance page 131 © 2006 Schneider Electric All Rights Reserved 130 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Min/Max True Power See “Minimum/Maximum Template” on 1500 — — — Factor Total page 131 Min/Max Displacement See “Minimum/Maximum Template” on 1510 — — — Power Factor Total page 131 Min/Max Real Power See “Minimum/Maximum Template” on 1520 — — — Total page 131 Min/Max Reactive See “Minimum/Maximum Template” on 1530 — — — Power Total page 131 Min/Max Apparent See “Minimum/Maximum Template” on 1540 — — — Power Total page 131 Min/Max THD/thd See “Minimum/Maximum Template” on 1550 — — — Voltage L-L page 131 Min/Max THD/thd See “Minimum/Maximum Template” on 1560 — — — Voltage L-N page 131 Min/Max THD/thd See “Minimum/Maximum Template” on 1570 — — — Current page 131 See “Minimum/Maximum Template” on 1580 Min/Max Frequency — — — page 131 See See “Minimum/Ma “Minimum/Maxim 1590 Min/Max End Time — ximum um Template” on Template” on page 131 page 131 Present Month Min/Max Group 2 Min/Max Voltage See “Minimum/Maximum Template” on 1600 — — — N-ground page 131 Min/Max Current, See “Minimum/Maximum Template” on 1610 — — — Neutral page 131 Previous Month Min/Max Group 2 Min/Max Voltage See “Minimum/Maximum Template” on 1650 — — — N-ground page 131 Min/Max Current, See “Minimum/Maximum Template” on 1660 — — — Neutral page 131 Minimum/Maximum Template Table A–1 Table A–1 Base Date/Time of Min — Date/Time when Min was recorded on page 123 on page 123 Base+3 Min Value 0 – 32,767 Min value metered for all phases Base+4 Phase of recorded Min* — 1 to 3 Phase of Min recorded Table A–1 Table A–1 Base+5 Date/Time of Max — Date/Time when Max was recorded on page 123 on page 123 Base+8 Max Value 0 – 32,767 Max value metered for all phases Phase of recorded Base+9 — 1 to 3 Phase of Max recorded Max* * Only applicable for multi-phase quantities © 2006 Schneider Electric All Rights Reserved 131 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Energy 1700 Energy, Real In — WH (1) 3-Phase total real energy into the load 1704 Energy, Reactive In — VArH (1) 3-Phase total reactive energy into the load 1708 Energy, Real Out — WH (1) 3-Phase total real energy out of the load 1712 Energy, Reactive Out — VArH (1) 3-Phase total reactive energy out of the load Energy, Real Total 1716 — WH (2) Total Real Energy In, Out or In + Out (signed/absolute) Energy, Reactive Total 1720 — VArH (2) Total Reactive Energy In, Out or In + Out (signed/absolute) 1724 Energy, Apparent — VAH (1) 3-Phase total apparent energy Energy, Conditional 3-Phase total accumulated conditional real 1728 — WH (1) Real In energy into the load Energy, Conditional 3-Phase total accumulated conditional reactive 1732 — VArH (1) Reactive In energy into the load Energy, Conditional 3-Phase total accumulated conditional real 1736 — WH (1) Real Out energy out of the load Energy, Conditional 3-Phase total accumulated conditional reactive 1740 — VArH (1) Reactive Out energy out of the load Energy, Conditional 3-Phase total accumulated conditional 1744 — VAH (1) Apparent apparent energy Energy, Incremental 3-Phase total accumulated incremental real 1748 Real In, Last Complete — WH (3) energy into the load Interval Energy. Incremental 3-Phase total accumulated incremental 1751 Reactive In, Last — VArH (3) reactive energy into the load Complete Interval Energy, Incremental 3-Phase total accumulated incremental real 1754 Real Out, Last — WH (3) energy out of the load Complete Interval Energy, Incremental 3-Phase total accumulated incremental 1757 Reactive Out, Last — VArH (3) reactive energy out of the load Complete Interval Energy, Incremental 3-Phase total accumulated incremental 1760 Apparent, Last — VAH (3) apparent energy Complete Interval Last Complete Interval Table A–1 Table A–1 Date/Time of last completed incremental 1763 — DateTime on page 123 on page 123 energy interval Energy, Incremental 3-Phase total accumulated incremental real 1767 Real In, Present — WH (3) energy into the load Interval Energy. Incremental 3-Phase total accumulated incremental 1770 Reactive In, Present — VArH (3) reactive energy into the load Interval Energy, Incremental 3-Phase total accumulated incremental real 1773 Real Out, Present — WH (3) energy out of the load Interval © 2006 Schneider Electric All Rights Reserved 132 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Energy, Incremental 3-Phase total accumulated incremental 1776 Reactive Out, Present — VArH (3) reactive energy out of the load Interval Energy, Incremental 3-Phase total accumulated incremental 1779 Apparent, Present — VAH (3) apparent energy Interval Energy, Reactive, 3-Phase total accumulated incremental 1782 — VArH (3) Quadrant 1 reactive energy – quadrant 1 Energy, Reactive, 3-Phase total accumulated incremental 1785 — VArH (3) Quadrant 2 reactive energy – quadrant 2 Energy, Reactive, 3-Phase total accumulated incremental 1788 — VArH (3) Quadrant 3 reactive energy – quadrant 3 Energy, Reactive, 3-Phase total accumulated incremental 1791 — VArH (3) Quadrant 4 reactive energy – quadrant 4 0 = Off (default) Conditional Energy 1794 — — 0 – 1 Control Status 1 = On (1) 0 – 9,999,999,999,999,999 (2) -9,999,999,999,999,999 – 9,999,999,999,999,999 (3) 0 – 999,999,999,999 Demand Demand — Current Demand System Configuration and Data 0 = Thermal Demand (default) 1 = Timed Interval Sliding Block 2 = Timed Interval Block 4 = Timed Interval Rolling Block 8 = Input Synchronized Block Demand Calculation 16 = Input Synchronized Rolling Block Mode 1800 — — 0 – 1024 32 = Command Synchronized Block Current 64 = Command Synchronized Rolling Block 128 = Clock Synchronized Block 256 = Clock Synchronized Rolling Block 512 = Slave to Power Demand Interval 1024 = Slave to Incremental Energy Interval Demand Interval 1801 — Minutes 1 – 60 Default = 15 Current Demand Subinterval 1802 — Minutes 1 – 60 Default = 1 Current Demand Sensitivity Adjusts the sensitivity of the thermal demand 1803 — 1% 1 – 99 calculation. Default = 90 Current Short Demand Interval Sets the interval for a running average demand 1805 — Seconds 0 – 60 calculation of short duration. Default = 15 Current Time Elapsed in Interval 1806 — Seconds 0 – 3,600 Time elapsed in the present demand interval. Current © 2006 Schneider Electric All Rights Reserved 133 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Time Elapsed in Time elapsed in the present demand Subinterval 1807 — Seconds 0 – 3,600 subinterval. Current Interval Count Count of demand intervals. Rolls over at 1808 — 1.0 0 – 32,767 32,767. Current Subinterval Count Count of demand subintervals. Rolls over at 1809 — 1.0 0 – 60 interval. Current Min/Max Reset Table A–1 Table A–1 Date/Time of last reset of Current Demand DateTime 1810 — on page 123 on page 123 Min/Max demands Current Min/Max Reset Count Count of Min/Max demand resets. Rolls over at 1814 — 1.0 0 – 32,767 32,767. Current Bit 00 = end of demand subinterval Demand System Bit 01 = end of demand interval Status 1815 — — 0x0000 – 0x000F Bit 02 = start of first complete interval Current Bit 03 = end of first complete interval Demand — Power Demand System Configuration and Data 0 = Thermal Demandlt) 1 = Timed Interval Sliding Block 2 = Timed Interval Block 4 = Timed Interval Rolling Block 8 = Input Synchronized Block Demand Calculation Mode 1840 — — 0 – 1024 16 = Input Synchronized Rolling Block Power 32 = Command Synchronized Block 64 = Command Synchronized Rolling Block 128 = Clock Synchronized Block 256 = Clock Synchronized Rolling Block 1024 = Slave to Incremental Energy Interval Demand Interval 1841 — Minutes 1 – 60 Default = 15 Power Demand Subinterval 1842 — Minutes 1 – 60 Default = 1 Power Demand Sensitivity Adjusts the sensitivity of the thermal demand 1843 — 1% 1 – 99 calculation. Default = 90 Power Predicted Demand Adjusts sensitivity of predicted demand Sensitivity 1844 — 1.0 1 – 10 calculation to recent changes in power consumption. Default = 5. Power Short Demand Interval Sets the interval for a running average demand 1845 — Seconds 0 – 60 calculation of short duration. Default = 15 Power Time Elapsed in Interval 1846 — Seconds 0 – 3,600 Time elapsed in the present demand interval. Power © 2006 Schneider Electric All Rights Reserved 134 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Time Elapsed in Time elapsed in the present demand Subinterval 1847 — Seconds 0 – 3,600 subinterval. Power Interval Count Count of demand intervals. Rolls over at 1848 — 1.0 0 – 32,767 32,767. Power Subinterval Count Count of demand subintervals. Rolls over at 1849 — 1.0 0 – 60 interval. Power Min/Max Reset Table A–1 Table A–1 Date/Time of last reset of Power Demand DateTime 1850 — on page 123 on page 123 Min/Max demands Power Min/Max Reset Count Count of Min/Max demand resets. Rolls over at 1854 — 1.0 0 – 32,767 32,767. Power Bit 00 = end of demand subinterval Demand System Bit 01 = end of demand interval Status 1855 — — 0x0000 – 0x000F Bit 02 = start of first complete interval Power Bit 03 = end of first complete interval Demand — Input Metering Demand System Configuration and Data 0 = Thermal Demand 1 = Timed Interval Sliding Block 2 = Timed Interval Block (default) 4 = Timed Interval Rolling Block 8 = Input Synchronized Block Demand Calculation 16 = Input Synchronized Rolling Block Mode 1860 — — 0 – 1024 32 = Command Synchronized Block Input Pulse Metering 64 = Command Synchronized Rolling Block 128 = Clock Synchronized Block 256 = Clock Synchronized Rolling Block 512 = Slave to Power Demand Interval 1024 = Slave to Incremental Energy Interval Demand Interval 1861 — Minutes 1 – 60 Default = 15 Input Pulse Metering Demand Subinterval 1862 — Minutes 1 – 60 Default = 1 Input Pulse Metering Demand Sensitivity Adjusts the sensitivity of the thermal demand 1863 — 1% 1 – 99 calculation. Default = 90 Input Pulse Metering Short Demand Interval Sets the interval for a running average demand 1865 — Seconds 0 – 60 calculation of short duration. Default = 15 Input Pulse Metering Time Elapsed in Interval 1866 — Seconds 0 – 3,600 Input Pulse Metering Time Elapsed in Subinterval 1867 — Seconds 0 – 3,600 Input Pulse Metering © 2006 Schneider Electric All Rights Reserved 135 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Interval Count 1868 — 1.0 0 – 32,767 Rolls over at 32,767. Input Pulse Metering Subinterval Count 1869 — 1.0 0 – 60 Rolls over at interval. Input Pulse Metering Min/Max Reset Table A–1 Table A–1 DateTime 1870 — on page 123 on page 123 Input Pulse Metering Min/Max Reset Count 1874 — 1.0 0 – 32,767 Rolls over at 32,767. Input Pulse Metering Bit 00 = end of demand subinterval Demand System Bit 01 = end of demand interval Status 1875 — — 0x0000 – 0x000F Bit 02 = start of first complete interval Input Pulse Metering Bit 03 = end of first complete interval Demand — Generic Demand System Configuration and Data 0 = Thermal Demand (default) 1 = Timed Interval Sliding Block 2 = Timed Interval Block 4 = Timed Interval Rolling Block 8 = Input Synchronized Block Demand Calculation 16 = Input Synchronized Rolling Block Mode 1880 — — 0 – 1024 32 = Command Synchronized Block Generic Group 1 64 = Command Synchronized Rolling Block 128 = Clock Synchronized Block 256 = Clock Synchronized Rolling Block 512 = Slave to Power Demand Interval 1024 = Slave to Incremental Energy Interval Demand Interval 1881 — Minutes 1 – 60 Default = 15 Generic Demand Subinterval 1882 — Minutes 1 – 60 Default = 1 Generic Demand Sensitivity Adjusts the sensitivity of the thermal demand 1883 — 1% 1 – 99 calculation. Default = 90 Generic Short Demand Interval Sets the interval for a running average demand 1885 — Seconds 0 – 60 calculation of short duration. Default = 15 Generic Time Elapsed in Interval 1886 — Seconds 0 – 3,600 Time elapsed in the present demand interval. Generic Time Elapsed in Time elapsed in the present demand Subinterval 1887 — Seconds 0 – 3,600 subinterval. Generic Interval Count Count of demand intervals. Rolls over at 1888 — 1.0 0 – 32,767 32,767. Generic © 2006 Schneider Electric All Rights Reserved 136 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Subinterval Count Count of demand subintervals. Rolls over at 1889 — 1.0 0 – 60 interval. Generic Min/Max Reset Table A–1 Table A–1 Date/Time of last reset of Generic Group 1 DateTime 1890 — on page 123 on page 123 Demand Min/Max demands Generic Min/Max Reset Count Count of Min/Max demand resets. Rolls over at 1894 — 1.0 0 – 32,767 32,767. Generic Bit 00 = end of demand subinterval Demand System Bit 01 = end of demand interval Status 1895 — — 0x0000 – 0x000F Bit 02 = start of first complete interval Generic Bit 03 = end of first complete interval Demand — Miscellaneous Demand System Configuration and Data Demand Forgiveness Duration of time after a power outage, during 1920 — Seconds 0 – 3,600 Duration which power demand is not calculated Duration of time that metered voltage must be Demand Forgiveness 1921 — Seconds 0 – 3,600 lost to be considered a power outage for Outage Definition demand forgiveness Time of day, in minutes from midnight, to which Clock Sync Time of the demand interval is to be synchronized. 1923 — Minutes 0 – 1,440 Day Applies to demand intervals configured as Clock Synchronized. -0.001 to 1000 to Power Factor Average 0.001 1924 Over Last Power — 0.001 Demand Interval (-32,768 if N/A) Cumulative Demand Table A–1 Table A–1 Date/Time of the last reset of cumulative 1925 — Reset DateTime on page 123 on page 123 demand Cumulative Input Pulse Table A–1 Table A–1 Date/Time of last reset of input pulse metering 1929 Metering Reset — on page 123 on page 123 accumulation DateTime Last Incremental Maximum real 3-phase power demand over the 1940 Interval, Real Demand F kW/Scale -32,767 – 32,767 last incremental energy interval Peak Last Incremental Date/Time of the Real Power Demand peak Table A–1 Table A–1 1941 Interval, Real Demand — during the last completed incremental energy on page 123 on page 123 Peak DateTime interval Last Incremental Maximum reactive 3-phase power demand 1945 Interval, Reactive F kVAr/Scale -32,767 – 32,767 over the last incremental energy interval Demand Peak Last Incremental Date/Time of the Reactive Power Demand Interval, Reactive Table A–1 Table A–1 1946 — peak during the last completed incremental Demand Peak on page 123 on page 123 energy interval DateTime Last Incremental Maximum apparent 3-phase power demand 1950 Interval, Apparent F kVA/Scale 0 – 32,767 over the last incremental energy interval Demand Peak Last Incremental Date/Time of the Apparent Power Demand Interval, Apparent Table A–1 Table A–1 1951 — peak during the last completed incremental Demand Peak on page 123 on page 123 energy interval DateTime © 2006 Schneider Electric All Rights Reserved 137 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Demand — Current Demand Channels Last Demand 1960 A Amps/Scale 0 – 32,767 Phase A current demand, last complete interval Current, Phase A Present Demand 1961 A Amps/Scale 0 – 32,767 Phase A current demand, present interval Current, Phase A Running Average Phase A current demand, running average Demand 1962 A Amps/Scale 0 – 32,767 demand calculation of short duration Current, Phase A Peak Demand 1963 A Amps/Scale 0 – 32,767 Phase A peak current demand Current, Phase A Peak Demand Table A–1 Table A–1 DateTime 1964 — Date/Time of Peak Current Demand, Phase A on page 123 on page 123 Current, Phase A Last Demand 1970 A Amps/Scale 0 – 32,767 Phase B current demand, last complete interval Current, Phase B Present Demand 1971 A Amps/Scale 0 – 32,767 Phase B current demand, present interval Current, Phase B Running Average Phase B current demand, running average Demand 1972 A Amps/Scale 0 – 32,767 demand calculation of short duration Current, Phase B Peak Demand 1973 A Amps/Scale 0 – 32,767 Phase B peak current demand Current Phase B Peak Demand DateTime Table A–1 Table A–1 1974 — Date/Time of Peak Current Demand, Phase B Current Phase B on page 123 on page 123 Last Demand Phase C current demand, last complete 1980 A Amps/Scale 0 – 32,767 interval Current, Phase C Present Demand 1981 A Amps/Scale 0 – 32,767 Phase C current demand, present interval Current, Phase C Running Average Phase C current demand, running average Demand 1982 A Amps/Scale 0 – 32,767 demand calculation of short duration Current, Phase C Peak Demand 1983 A Amps/Scale 0 – 32,767 Phase C peak current demand Current Phase C Peak Demand Table A–1 Table A–1 DateTime 1984 — Date/Time of Peak Current Demand, Phase C on page 123 on page 123 Current Phase C Last Demand 0 – 32,767 Neutral current demand, last complete interval 1990 A Amps/Scale Current, Neutral (-32,768 if N/A) 4-wire system only Present Demand 0 – 32,767 Neutral current demand, present interval 1991 A Amps/Scale Current, Neutral (-32,768 if N/A) 4-wire system only © 2006 Schneider Electric All Rights Reserved 138 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Running Average Neutral current demand, running average 0 – 32,767 Demand demand calculation of short duration 1992 A Amps/Scale (-32,768 if N/A) Current, Neutral 4-wire system only Peak Demand 0 – 32,767 Neutral peak current demand 1993 A Amps/Scale Current, Neutral (-32,768 if N/A) 4-wire system only Peak Demand Table A–1 Date/Time of Peak Current Demand, Neutral Table A–1 DateTime on page 123 1994 — on page 123 4-wire system only Current, Neutral (-32,768 if N/A) Last Demand 3-Phase Average current demand, last 2000 A Amps/Scale 0 – 32,767 Current, 3-Phase complete interval Average Present Demand 3-Phase Average current demand, present 2001 A Amps/Scale 0 – 32,767 Current, 3-Phase interval Average Running Average Demand 3-Phase Average current demand, short sliding 2002 A Amps/Scale 0 – 32,767 block Current, 3-Phase Average Peak Demand 2003 A Amps/Scale 0 – 32,767 3-Phase Average peak current demand Current, 3-Phase Average Peak Demand DateTime Table A–1 Table A–1 Date/Time of Peak Current Demand, 3-Phase 2004 Current, 3-Phase — on page 123 on page 123 Average Average Demand — Power Demand Channels Last Demand 3-Phase total present real power demand for 2150 F kW/Scale -32,767 – 32,767 last completed demand interval – updated Real Power, 3-Phase every sub-interval Total Present Demand 3-Phase total present real power demand for 2151 F kW/Scale -32,767 – 32,767 Real Power, 3-Phase present demand interval Total Running Average Demand 2152 F kW/Scale -32,767 – 32,767 Updated every second Real Power, 3-Phase Total Predicted Demand Predicted real power demand at the end of the 2153 F kW/Scale -32,767 – 32,767 Real Power, 3-Phase present interval Total Peak Demand 2154 F kW/Scale -32,767 – 32,767 Real Power, 3-Phase Total Peak Demand DateTime Table A–1 Table A–1 2155 — on page 123 on page 123 Real Power, 3-Phase Total © 2006 Schneider Electric All Rights Reserved 139 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Cumulative Demand -2147483648 – 2159 F kW/Scale Real Power, 3-Phase 2147483647 Total 1,000 Power Factor, Average Average True Power Factor at the time of the 2161 @ Peak Demand, Real — 0.001 -100 to 100 Peak Real Demand Power (-32,768 if N/A) Power Demand, Reactive Power Demand at the time of the 2162 Reactive @ Peak F kVAr/Scale -32,767 – 32,767 Peak Real Demand Demand, Real Power Power Demand, Apparent Power Demand at the time of the 2163 Apparent @ Peak F kVA/Scale 0 – 32,767 Peak Real Demand Demand, Real Power Last Demand 3-Phase total present reactive power demand 2165 F kVAr /Scale -32,767 – 32,767 for last completed demand interval – updated Reactive Power, 3- every sub-interval Phase Total Present Demand 3-Phase total present real power demand for 2166 F kVAr /Scale -32,767 – 32,767 Reactive Power, 3- present demand interval Phase Total Running Average 3-Phase total present reactive power demand, Demand 2167 F kVAr /Scale -32,767 – 32,767 running average demand calculation of short Reactive Power, 3- duration – updated every second Phase Total Predicted Demand Predicted reactive power demand at the end of 2168 F kVAr /Scale -32,767 – 32,767 Reactive Power, 3- the present interval Phase Total Peak Demand 2169 F kVAr /Scale -32,767 – 32,767 Reactive Power, 3- Phase Total Peak Demand DateTime Table A–1 Table A–1 2170 — on page 123 on page 123 Reactive Power, 3- Phase Total Cumulative Demand -2147483648 – 2174 F kVAr /Scale Reactive Power, 3- 2147483647 Phase Total 1,000 Power Factor, Average Average True Power Factor at the time of the 2176 @ Peak Demand, — 0.001 -100 to 100 Peak Reactive Demand Reactive Power (-32,768 if N/A) Power Demand, Real @ Real Power Demand at the time of the Peak 2177 F kW/Scale -32,767 – 32,767 Reactive Demand Peak Demand, Reactive Power Power Demand, Apparent @ Peak Apparent Power Demand at the time of the 2178 F kVA/Scale 0 – 32,767 Demand, Reactive Peak Reactive Demand Power © 2006 Schneider Electric All Rights Reserved 140 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Last Demand 3-Phase total present apparent power demand 2180 F kVA /Scale -32,767 – 32,767 for last completed demand interval – updated Apparent Power 3- every sub-interval Phase Total Present Demand 3-Phase total present apparent power demand 2181 F kVA /Scale -32,767 – 32,767 Apparent Power, 3- for present demand interval Phase Total Running Average 3-Phase total present apparent power demand, Demand 2182 F kVA /Scale -32,767 – 32,767 running average demand calculation of short Apparent Power, 3- duration – updated every second Phase Total Predicted Demand Predicted apparent power demand at the end 2183 F kVA /Scale -32,767 – 32,767 Apparent Power, 3- of the present interval Phase Total Peak Demand 3-Phase total peak apparent power demand 2184 F kVA /Scale -32,767 – 32,767 Apparent Power, 3- peak Phase Total Peak Demand DateTime Table A–1 Table A–1 Date/Time of 3-Phase peak apparent power 2185 — on page 123 on page 123 demand Apparent Power, 3- Phase Total Cumulative Demand -2,147,483,648 – 2189 F kVA /Scale Cumulative Demand, Apparent Power Apparent Power, 3- 2,147,483,647 Phase Total 1,000 Power Factor, Average Average True Power Factor at the time of the 2191 @ Peak Demand, — 0.001 -100 to 100 Peak Apparent Demand Apparent Power (-32,768 if N/A) Power Demand, Real Real Power Demand at the time of the Peak 2192 @ Peak Demand, F kW/Scale -32,767 – 32,767 Apparent Demand Apparent Power Power Demand, Reactive @ Peak Reactive Power Demand at the time of the 2193 F kVAr/Scale 0 – 32,767 Demand, Apparent Peak Apparent Demand Power Demand — Input Metering Demand Channels Consumption Units Units in which consumption is to be Code accumulated 2200 — — See Unit Codes Input Channel #1 Default = 0 Units in which demand (rate) is to be Demand Units Code expressed 2201 — — See Unit Codes Input Channel #1 Default = 0 Last Demand Last complete interval, updated every sub- 2202 Input Channel #1 — — 0 – 32,767 interval Present Demand 2203 — — 0 – 32,767 Present interval Input Channel #1 © 2006 Schneider Electric All Rights Reserved 141 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Running Average Running average demand calculation of short Demand 2204 — — 0 – 32,767 duration, updated every second Input Channel #1 Peak Demand 2205 Input Channel #1 — — 0 – 32,767 Peak Demand Table A–1 Table A–1 Date/Time 2206 — on page 123 on page 123 Input Channel #1 Minimum Demand 2210 — — 0 – 32,767 Input Channel #1 Minimum Demand Table A–1 Table A–1 Date/Time 2211 — on page 123 on page 123 Input Channel #1 Cumulative Usage The user must identify the units to be used in 2215 — (2) (1) the accumulation. Input Channel #1 Same as registers 2200 – 2219 except for 2220 Input Channel #2 Channel #2 Same as registers 2200 – 2219 except for 2240 Input Channel #3 Channel #3 Same as registers 2200 – 2219 except for 2260 Input Channel #4 Channel #4 Same as registers 2200 – 2219 except for 2280 Input Channel #5 Channel #5 Demand — Generic Group 1 Demand Channels Input Register Register selected for generic demand 2400 — — — calculation Generic Channel #1 Unit Code 2401 — — -32,767 – 32,767 Used by software Generic Channel #1 Scale Code 2402 — — -3 – 3 Generic Channel #1 Last Demand 2403 — — 0 – 32,767 Generic Channel #1 Present Demand 2404 Generic Channel #1 — — 0 – 32,767 Running Average Demand 2405 — — 0 – 32,767 Updated every second Generic Channel #1 Peak Demand 2406 Generic Channel #1 — — 0 – 32,767 © 2006 Schneider Electric All Rights Reserved 142 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Peak Demand Table A–1 Table A–1 Date/Time 2407 — on page 123 on page 123 Generic Channel #1 Minimum Demand 2411 — — 0 – 32,767 Generic Channel #1 Minimum Demand Table A–1 Table A–1 Date/Time 2412 — on page 123 on page 123 Generic Channel #1 Same as registers 2400 – 2419 except for 2420 Generic Channel #2 Channel #2 Same as registers 2400 – 2419 except for 2440 Generic Channel #3 Channel #3 Same as registers 2400 – 2419 except for 2460 Generic Channel #4 Channel #4 Same as registers 2400 – 2419 except for 2480 Generic Channel #5 Channel #5 Same as registers 2400 – 2419 except for 2500 Generic Channel #6 Channel #6 Same as registers 2400 – 2419 except for 2520 Generic Channel #7 Channel #7 Same as registers 2400 – 2419 except for 2540 Generic Channel #8 Channel #8 Same as registers 2400 – 2419 except for 2560 Generic Channel #9 Channel #9 Same as registers 2400 – 2419 except for 2580 Generic Channel #10 Channel #10 Phase Extremes Current, Highest Phase 2800 A Amps/Scale 0 – 32,767 Highest value of Phases A, B, C or N Value Current, Lowest Phase 2801 A Amps/Scale 0 – 32,767 Lowest value of Phases A, B, C or N Value Voltage, L-L, Highest 2802 D Volts/Scale 0 – 32,767 Highest value of Phases A-B, B-C or C-A Value Voltage, L-L, Lowest 2803 D Volts/Scale 0 – 32,767 Lowest value of Phases A-B, B-C or C-A Value 0 – 32,767 Highest value of Phases A-N, B-N or C-N Voltage, L-N, Highest 2804 D Volts/Scale Value (-32,768 if N/A) 4-wire system only 0 – 32,767 Lowest value of Phases A-N, B-N or C-N Voltage, L-N, Lowest 2805 D Volts/Scale Value (-32,768 if N/A) 4-wire system only System Configuration Power Meter 3002 — — — Nameplate Power Meter Present Operating System 0x0000 – 3014 — — Firmware Revision 0xFFFF Level © 2006 Schneider Electric All Rights Reserved 143 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Table A–1 Table A–1 3034 Present Date/Time — on page 123 on page 123 Table A–1 Table A–1 3039 Last Unit Restart — Last unit restart time on page 123 on page 123 Number of Metering 3043 — 1.0 0 – 32,767 System Restarts Number of Control 3044 — 1.0 0 – 32,767 Power Failures Control Power Failure Table A–1 Table A–1 3045 — Date/Time of last control power failure Date/Time on page 123 on page 123 1 = shutdown & soft reset (restart F/W) 2 = shutdown & hard reset (load from flash and run) 3 = shutdown & hard reset and set memory to Cause of Last Meter default 3049 — — 1 – 20 Reset 10 = shutdown with no reset (used by DLF) 12 = already shutdown, hard reset only (used by DLF) 20 = Power failure 0 = Normal; 1 = Error Bit 00 = Is set to “1” if any failure occurs Bit 01 = RTC failure Bit 02 = Reserved Bit 03 = Reserved Bit 04 = Reserved Bit 05 = Metering Collection overrun failure Bit 06 = Reserved 0x0000 – 3050 Self-Test Results — — 0xFFFF Bit 07 = Metering Process 1.0 overrun failure Bit 08 = Reserved Bit 09 = Reserved Bit 10 = Reserved Bit 11 = Reserved Bit 12 = Reserved Bit 13 = Reserved Bit 14 = Reserved Bit 15 = Reserved © 2006 Schneider Electric All Rights Reserved 144 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes 0 = Normal; 1 = Error Bit 00 = tbd Aux I/O failure Bit 01 = tbd Option Slot A module failure Bit 02 = tbd Option Slot B module failure Bit 03 = Bit 04 = Bit 05 = Bit 06 = 0x0000 – 3051 Self Test Results — — Bit 07 = 0xFFFF Bit 08 = OS Create failure Bit 09 = OS Queue overrun failure Bit 10 = Bit 11 = Bit 12 = Bit 13 = Systems shut down due to continuous reset Bit 14 = Unit in Download, Condition A Bit 15 = Unit in Download, Condition B Used by sub-systems to indicate that a value used within that system has been internally modified 0 = No modifications; 1 = Modifications Bit 00 = Summary bit 0x0000 – 3052 Configuration Modified — — Bit 01 = Metering System 0xFFFF Bit 02 = Communications System Bit 03 = Alarm System Bit 04 = File System Bit 05 = Auxiliary I/O System Bit 06 = Display System 3093 Present Month — Months 1 – 12 3094 Present Day — Days 1 – 31 3095 Present Year — Years 2,000 – 2,043 3096 Present Hour — Hours 0 – 23 3097 Present Minute — Minutes 0 – 59 3098 Present Second — Seconds 0 – 59 3099 Day of Week — 1.0 1 – 7 Sunday = 1 © 2006 Schneider Electric All Rights Reserved 145 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Current/Voltage Configuration CT Ratio, Phase A 3138 — 0.00001 -20,000 – 20,000 Default = 0 Correction Factor CT Ratio, Phase B 3139 — 0.00001 -20,000 – 20,000 Default = 0 Correction Factor CT Ratio, Phase C 3140 — 0.00001 -20,000 – 20,000 Default = 0 Correction Factor PT Ratio, Phase A 3142 — 0.00001 -20,000 – 20,000 Default = 0 Correction Factor PT Ratio, Phase B 3143 — 0.00001 -20,000 – 20,000 Default = 0 Correction Factor PT Ratio, Phase C 3144 — 0.00001 -20,000 – 20,000 Default = 0 Correction Factor Field Calibration Table A–1 Table A–1 3150 — Date/Time on page 123 on page 123 Phase A Current 3154 — 0.00001 -20,000 – 20,000 Default = 0 Field Calibration Coefficient Phase B Current 3155 — 0.00001 -20,000 – 20,000 Default = 0 Field Calibration Coefficient Phase C Current 3156 — 0.00001 -20,000 – 20,000 Default = 0 Field Calibration Coefficient Phase A Voltage 3158 — 0.00001 -20,000 – 20,000 Default = 0 Field Calibration Coefficient Phase B Voltage 3159 — 0.00001 -20,000 – 20,000 Default = 0 Field Calibration Coefficient Phase C Voltage Default = 0 3160 — 0.00001 -20,000 – 20,000 Field Calibration Coefficient Neutral-Ground Voltage 3161 — 0.00001 -20,000 – 20,000 Default = 0 Field Calibration Coefficient Phase Shift Correction in the range of –10º to CT Phase Shift 3170 — — -1,000 – 1,000 +10º. A negative shifts in the lag direction. Correction @ 1 amp Default = 0 Phase Shift Correction in the range of –10º to CT Phase Shift 3171 — — -1,000 – 1,000 +10º. A negative shifts in the lag direction. Correction @ 5 amps Default = 0 © 2006 Schneider Electric All Rights Reserved 146 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Metering Configuration and Status Metering Configuration and Status — Basic 30 = 3PH3W2CT 31 = 3PH3W3CT 3200 Metering System Type — 1.0 30, 31, 40, 42 40 = 3PH4W3CT (default) 42 = 3PH4W3CT2PT CT Ratio, 3-Phase 3201 — 1.0 1 – 32,767 Default = 5 Primary CT Ratio, 3-Phase 3202 — 1.0 1, 5 Default = 5 Secondary PT Ratio, 3-Phase 3205 — 1.0 1 – 32,767 Default = 120 Primary Default = 0 PT Ratio, 3-Phase 3206 — 1.0 -1 – 2 Primary Scale Factor -1 = Direct Connect PT Ratio, 3-Phase 100, 110, 115, 3207 — 1.0 Default = 120 Secondary 120 Nominal System 3208 — Hz 50, 60, 400 Default = 60 Frequency Power of 10 Scale A – 3 Phase 3209 — 1.0 -2 – 1 Amps Default = 0 Power of 10 Scale B – Neutral 3210 — 1.0 -2 – 1 Amps Default = 0 Power of 10 Scale D – 3 Phase 3212 — 1.0 -1 – 2 Volts Default = 0 Power of 10 3213 Scale E – Neutral Volts — 1.0 -2 – 2 Default = -1 Power of 10 3214 Scale F – Power — 1.0 -3 – 3 Default = 0 © 2006 Schneider Electric All Rights Reserved 147 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Default = 0 Bit 00 = Reserved Bit 01 = Reactive Energy & Demand Accumulation 0 = Fund. Only; 1 = Harmonics Included Bit 02 = PF Sign Convention 0 = IEEE Convention 1 = IEC Convention Bit 03 = Reserved Bit 04 = Reserved Bit 05 = Reserved Bit 06 = Conditional Energy Accumulation Operating Mode 0x0000 – 3227 — Binary Control Parameters 0x0FFF 0 = Inputs; 1 = Command Bit 07 = Reserved Bit 08 = Display Setup 0 = Enabled 1 = Disabled Bit 09 = Normal Phase Rotation 0 = ABC 1 = CBA Bit 10 = Total Harmonic Distortion Calculation 0 = THD (% Fundamental) 1 = thd (% Total RMS) Bit 11 = Reserved 0 = ABC Phase Rotation 3228 — 1.0 0 – 1 Direction 1 = CBA Default = 60 Incremental Energy 3229 — Minutes 0 – 1440 Interval 0 = Continuous Accumulation Minutes from midnight Incremental Energy 3230 — Minutes 0 – 1440 Interval Start Time Default = 0 Minutes from midnight Incremental Energy 3231 — Minutes 0 – 1440 Interval End Time Default = 1440 0 = Absolute (default) Energy Accumulation 3232 — 1.0 0 – 1 Mode 1 = Signed Peak Current Demand Entered by the user for use in calculation of Over Last Year Total Demand Distortion. 3233 — Amps 0 – 32,767 (currently not 0 = Calculation not performed (default) calculated) © 2006 Schneider Electric All Rights Reserved 148 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Metering Configuration and Status — Harmonics 0 = Disabled Harmonic Quantity 3240 — 1.0 0 – 3 1 = Harmonic magnitudes only (default) Selection 2 = Harmonic magnitudes and angles 0 = % of Fundamental (default) Voltage Harmonic 3241 — 1.0 0 - 2 1 = % of RMS Magnitude Format 2 = RMS 0 = % of Fundamental (default) Current Harmonic 3242 — 1.0 0 - 2 1 = % of RMS Magnitude Format 2 = RMS Harmonic Refresh 3243 — Seconds 10 – 60 Default = 30 Interval Time Remaining Until The user may write to this register to stretch 3244 — Seconds 10 – 60 Harmonic Refresh the hold time. Bitmap indicating active Harmonic Channels 0 = Inactive 1 = Active Bit 00 = Vab Bit 01 = Vbc Bit 02 = Vca Bit 03 = Van Harmonic Channel 0x0000 – 3245 — Binary Map 0x7FFF Bit 04 = Vbn Bit 05 = Vcn Bit 06 = Reserved (Neutral to Ref) Bit 07 = Ia Bit 08 = Ib Bit 09 = Ic Bit 10 = In Bit 11-15 = Reserved 0 = Processing (default) Harmonic Report 3246 — 1.0 0 – 1 Status 1 = Holding 0 = Disabled (default) Display 1 second 3248 Metering Floating Point — — 0 –1 1 = Enabled Values Values begin at register 11700 © 2006 Schneider Electric All Rights Reserved 149 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Metering Configuration and Status — Diagnostics 0 = Normal 1 = Error Bit 00 = Summary Bit (On if any other bit is on) Bit 01 = Configuration Error Metering System 0x0000 – 3254 — Binary Bit 02 = Scaling Error Diagnostic Summary 0xFFFF Bit 03 = Phase Loss Bit 04 = Wiring Error Bit 05 = Incremental Energy may be incorrect due to meter reset Bit 06 = External Demand Sync Timeout 0 = Normal 1 = Error Bit 00 = Summary Bit (On if any other bit is on) Metering System 0x0000 – 3255 Configuration Error — Binary Bit 01 = Logical Configuration Error 0xFFFF Summary Bit 02 = Demand System Configuration Error Bit 03 = Energy System Configuration Error Bit 04 = Reserved Bit 05 = Metering Configuration Error 0 = Normal 1 = Error Bit 00 = Summary Bit (On if any other bit is on) Bit 01 = Wiring Check Aborted Bit 02 = System type setup error Bit 03 = Frequency out of range Bit 04 = No voltage Bit 05 = Voltage imbalance Wiring Error Detection 0x0000 – Bit 06 = Not enough load to check connections 3257 — Binary 1 0xFFFF Bit 07 = Check meter configured for direct connect Bit 08 = All CT reverse polarity Bit 09 = Reserved Bit 10 = Reserved Bit 11 = Reserved Bit 12 = Reserved Bit 13 = Reserved Bit 14 = Phase rotation not as expected Bit 15 = Negative kW is usually abnormal © 2006 Schneider Electric All Rights Reserved 150 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes 0 = Normal 1 = Error Bit 00 = Van magnitude error Bit 01 = Vbn magnitude error Bit 02 = Vcn magnitude error Bit 03 = Vab magnitude error Bit 04 = Vbc magnitude error Bit 05 = Vca magnitude error Wiring Error Detection 0x0000 – 3258 — Binary Bit 06 = Van angle not as expected 2 0xFFFF Bit 07 = Vbn angle not as expected Bit 08 = Vcn angle not as expected Bit 09 = Vab angle not as expected Bit 10 = Vbc angle not as expected Bit 11 = Vca angle not as expected Bit 12 = Vbn is reversed polarity Bit 13 = Vcn is reversed polarity Bit 14 = Vbc is reversed polarity Bit 15 = Vca is reversed polarity 0 = Normal 1 = Error Bit 00 = Move VTa to VTb Bit 01 = Move VTb to VTc Bit 02 = Move VTc to VTa Bit 03 = Move VTa to VTc Bit 04 = Move VTb to VTa Bit 05 = Move VTc to VTb Wiring Error Detection 0x0000 – 3259 — Binary Bit 06 = Reserved 3 0xFFFF Bit 07 = Reserved Bit 08 = Reserved Bit 09 = Reserved Bit 10 = Ia is < 1% of CT Bit 11 = Ib is < 1% of CT Bit 12 = Ic is < 1% of CT Bit 13 = Ia angle not in expected range Bit 14 = Ib angle not in expected range Bit 15 = Ic angle not in expected range © 2006 Schneider Electric All Rights Reserved 151 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes 0 = Normal 1 = Error Bit 00 = CTa reversed polarity Bit 01 = CTb reversed polarity Bit 02 = CTc reversed polarity Bit 03 = Reserved Bit 04 = Move CTa to CTb Bit 05 = Move CTb to CTc Wiring Error Detection 0x0000 – 3260 — Binary Bit 06 = Move CTc to Cta 4 0xFFFF Bit 07 = Move CTa to CTc Bit 08 = Move CTb to Cta Bit 09 = Move CTc to CTb Bit 10 = Move CTa to CTb & reverse polarity Bit 11 = Move CTb to CTc & reverse polarity Bit 12 = Move CTc to CTa & reverse polarity Bit 13 = Move CTa to CTc & reverse polarity Bit 14 = Move CTb to CTa & reverse polarity Bit 15 = Move CTc to CTb & reverse polarity Indicates potential over range due to scaling error 0 = Normal 1 = Error Bit 00 = Summary Bit (On if any other bit is on) 3261 Scaling Error — Binary 0x0000 – 0x003F Bit 01 = Scale A – Phase Current Error Bit 02 = Scale B – Neutral Current Error Bit 03 = Unused Bit 04 = Scale D – Phase Voltage Error Bit 05 = Scale E – Neutral Voltage Error Bit 06 = Scale F – Power Error © 2006 Schneider Electric All Rights Reserved 152 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes 0 = OK 1 = Phase Loss Bit 00 = Summary Bit (On if any other bit is on) Bit 01 = Voltage Phase A Bit 02 = Voltage Phase B Bit 03 = Voltage Phase C 0x0000 – 0x007F 3262 Phase Loss Bitmap — Binary Bit 04 = Current Phase A (-32,768 if N/A) Bit 05 = Current Phase B Bit 06 = Current Phase C This register is controlled by the voltage and current phase loss alarms. These alarms must be configured and enabled for this register to be populated. Metering Configuration and Status — Resets Previous Month Table A–1 Table A–1 3266 Minimum/Maximum — on page 123 on page 123 Start Date/Time Present Month Table A–1 Table A–1 3270 Minimum/Maximum — on page 123 on page 123 Reset Date/Time Accumulated Energy Table A–1 Table A–1 Reset 3274 — on page 123 on page 123 Date/Time Conditional Energy Table A–1 Table A–1 Reset 3278 — on page 123 on page 123 Date/Time Incremental Energy Table A–1 Table A–1 Reset 3282 — on page 123 on page 123 Date/Time Input Metering Table A–1 Table A–1 3286 Accumulation Reset — on page 123 on page 123 Date/Time Accumulated Energy Table A–1 Table A–1 Preset 3290 — on page 123 on page 123 Date/Time © 2006 Schneider Electric All Rights Reserved 153 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–3: Abbreviated Register List Reg Name Scale Units Range Notes Communications Communications — RS485 0 = Modbus (default) 3400 Protocol — — 0 – 2 1 = Jbus Valid Addresses: (Default = 1) 3401 Address — — 0 – 255 Modbus: 0 – 247 Jbus: 0 – 255 3 = 9600 (default) 3402 Baud Rate — — 0 – 5 4 = 19200 5 = 38400 0 = Even (default) 3403 Parity — — 0 – 2 1 = Odd 2 = None Number of valid messages addressed to this 3410 Packets To This Unit — — 0 – 32,767 unit Number of valid messages addressed to other 3411 Packets To Other Units — — 0 – 32,767 units Packets With Invalid Number of messages received with invalid 3412 — — 0 – 32,767 Address address 3413 Packets With Bad CRC — — 0 – 32,767 Number of messages received with bad CRC 3414 Packets With Error — — 0 – 32,767 Number of messages received with errors Packets With Illegal Number of messages received with an illegal 3415 — — 0 – 32,767 Opcode opcode Packets With Illegal Number of messages received with an illegal 3416 — — 0 – 32,767 Register register Invalid Write 3417 — — 0 – 32,767 Number of invalid write responses Responses Packets With Illegal Number of messages received with an illegal 3418 — — 0 – 32,767 Counts count Packets With Frame Number of messages received with a frame 3419 — — 0 – 32,767 Error error 3420 Broadcast Messages — — 0 – 32,767 Number of broadcast messages received 3421 Number Of Exceptions — — 0 – 32,767 Number of exception replies Messages With Good Number of messages received with a good 3422 — — 0 – 32,767 CRC CRC 3423 Modbus Event Counter — — 0 – 32,767 Modbus Event Counter © 2006 Schneider Electric All Rights Reserved 154 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–4: Registers for Inputs and Outputs Reg Name Scale Units Range Notes Auxiliary Inputs and Outputs 0 = Off 1 = On Discrete Input Status 4000 — — — Standard Discrete Bit 00 = Not Used Input Bit 01 = Standard discrete input I/O Point 2 Remaining bits unused 0 = Off 1 = On Discrete Input Status 4000 — — — Standard Discrete Bit 00 = Not Used Input Bit 01 = Standard discrete input I/O Point 2 Remaining bits unused 0 = Off 1 = On Bit 00 = On/Off Status of I/O Point 3 Bit 01 = On/Off Status of I/O Point 4 Discrete Input Status Bit 02 = On/Off Status of I/O Point 5 4001 — — 0x0000 – 0xFFFF Position A Bit 03 = On/Off Status of I/O Point 6 Bit 04 = On/Off Status of I/O Point 7 Bit 05 = On/Off Status of I/O Point 8 Bit 06 = On/Off Status of I/O Point 9 Bit 07 = On/Off Status of I/O Point 10 Remaining bits unused 0 = Off 1 = On Bit 00 = On/Off Status of I/O Point 11 Bit 01 = On/Off Status of I/O Point 12 Bit 02 = On/Off Status of I/O Point 13 Discrete Input Status 4002 — — 0x0000 – 0xFFFF Bit 03 = On/Off Status of I/O Point 14 Position B Bit 04 = On/Off Status of I/O Point 15 Bit 05 = On/Off Status of I/O Point 16 Bit 06 = On/Off Status of I/O Point 17 Bit 07 = On/Off Status of I/O Point 18 Remaining bits unused 4003 Reserved — — — Reserved for future development © 2006 Schneider Electric All Rights Reserved 155 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–4: Registers for Inputs and Outputs Reg Name Scale Units Range Notes 0 = Off 1= On Discrete Output Status 4005 Standard Discrete — — 0x0000 – 0x0001 Bit 00 = Standard discrete output, I/O Output Point 1 Remaining bits unused 0 = Off 1 = On Bit 00 = On/Off Status of I/O Point 3 Bit 01 = On/Off Status of I/O Point 4 Discrete Output Status Bit 02 = On/Off Status of I/O Point 5 4006 — — 0x0000 – 0xFFFF Position A Bit 03 = On/Off Status of I/O Point 6 Bit 04 = On/Off Status of I/O Point 7 Bit 05 = On/Off Status of I/O Point 8 Bit 06 = On/Off Status of I/O Point 9 Bit 07 = On/Off Status of I/O Point 10 Remaining bits unused 0 = Off 1 = On Bit 00 = On/Off Status of I/O Point 11 Bit 01 = On/Off Status of I/O Point 12 Discrete Output Status Bit 02 = On/Off Status of I/O Point 13 4007 — — 0x0000 – 0xFFFF Position B Bit 03 = On/Off Status of I/O Point 14 Bit 04 = On/Off Status of I/O Point 15 Bit 05 = On/Off Status of I/O Point 16 Bit 06 = On/Off Status of I/O Point 17 Bit 07 = On/Off Status of I/O Point 18 Remaining bits unused 4008 Reserved — — — Reserved for future development 0 = OK 1 = Error Bit 00 = Summary bit IO System Diagnostic 4010 — — 0x0000 – 0x007F Summary Bit 01 = I/O Error – Standard Bit 02 = I/O Error – I/O Position A Bit 03 = I/O Error – I/O Position B Remaining bits unused © 2006 Schneider Electric All Rights Reserved 156 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–4: Registers for Inputs and Outputs Reg Name Scale Units Range Notes 0 = OK 1 = Error IO Module Health Bit 00 = Module error summary Status 4011 — — 0x0000 – 0x000F Bit 01 = Point error summary Standard IO Bit 02 = Module removed while meter is running Bit 03 = Module change validation failed Remaining bits unused 0 = OK 1 = Error IO Module Health Bit 00 = Module error summary Status 4012 — — 0x0000 – 0x000F Bit 01 = Point error summary Bit Position A Bit 02 = Module removed while meter is running Bit 03 = Module change validation failed Remaining bits unused 0 = OK 1 = Error IO Module Health Bit 00 = Module error summary Status 4013 — — 0x0000 – 0x000F Bit 01 = Point error summary Bit Position B Bit 02 = Module removed while meter is running Bit 03 = Module change validation failed Remaining bits unused 4014 Reserved — — — Reserved for future development Present Module Type 4020 — — 255 Should always be 255 Standard IO 0 = Not Installed 1 = Reserved Present Module Type 4021 — — 0 – 7 2 = IO-22 Position A 3 = IO-26 4 = IO-2222 0 = Not Installed 1 = Reserved Present Module Type 4022 — — 0 – 7 2 = IO-22 Position B 3 = IO-26 4 = IO-2222 Extended MBUS 4023 — — — 0x39 = Logging Module Device 4024 Reserved — — — Reserved for future development Previous Module Type 4025 — — 255 Should always be 255 Standard IO © 2006 Schneider Electric All Rights Reserved 157 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–4: Registers for Inputs and Outputs Reg Name Scale Units Range Notes Indicates the I/O option module present the last time the meter was reset. 0 = Not Installed Previous Module Type 4026 — — 0 – 7 1 = Reserved Position A 2 = IO-22 3 = IO-26 4 = IO-2222 Indicates the I/O option module present the last time the meter was reset. 0 = Not Installed Previous Module Type 4027 — — 0 – 7 1 = Reserved Position B 2 = IO-22 3 = IO-26 4 = IO-2222 4028 Reserved — — — Reserved for future development Last Module Type 4030 — — 255 Should always be 255 Standard IO Indicates the last valid I/O module type successfully installed 0 = Not Installed Last Module Type 4031 — — 0 – 7 1 = Reserved Position A 2 = IO-22 3 = IO-26 4 = IO-2222 Indicates the last valid I/O module type successfully installed 0 = Not Installed Last Module Type 4032 — — 0 – 7 1 = Reserved Position B 2 = IO-22 3 = IO-26 4 = IO-2222 4033 Reserved — — — Reserved for future development 4080 Reserved — — — Reserved for future development Hardware Revision Number 4081 Analog I/O Option — — ASCII/HEX 4 ASCII bytes Module Position A © 2006 Schneider Electric All Rights Reserved 158 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–4: Registers for Inputs and Outputs Reg Name Scale Units Range Notes Firmware Revision Number 4083 Analog I/O Option — — Module Position A Date/Time of Mfg and/or Calibration 4084 Analog I/O Option — — Module Position A 4087 Reserved — — — Reserved for future development Serial Number Analog I/O Option 4088 — — Module Position A Process Registers Analog I/O Option 4090 — — Module Position A 4100 Reserved — — — Reserved for future development Hardware Revision Number 4101 Analog I/O Option — — ASCII 4 ASCII bytes Module Position B Firmware Revision Number 4103 Analog I/O Option — — Module Position B Date/Time of Mfg and/or Calibration 4104 Analog I/O Option — — Module Position B 4107 Reserved — — — Reserved for future development Serial Number Analog I/O Option 4108 — — Module Position B Process Registers Analog I/O Option 4110 — — Module Position B 4111 Reserved — — — Reserved for future development © 2006 Schneider Electric All Rights Reserved 159 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–4: Registers for Inputs and Outputs Reg Name Scale Units Range Notes Table of discrete output/alarm associations. Discrete Output/Alarm 4200 — — 0 – 4682 Upper byte is the I/O Point Number (1 – 18). Table Lower byte is the Alarm Index Number (1 – 74). Standard and Option Modules IO Point Number 1 4 300 Refer to Discrete Output template below. Standard Discrete Output I/O point 1 IO Point Number 2 4330 Refer to Discrete Input template below. Standard Discrete Input I/O point 2 Register contents depend on the I/O Point Type. 4360 IO Point Number 3 Refer to the I/O templates in this table. Register contents depend on the I/O Point Type. 4390 IO Point Number 4 Refer to the I/O templates in this table. Register contents depend on the I/O Point Type. 4420 IO Point Number 5 Refer to the I/O templates in this table. Register contents depend on the I/O Point Type. 4450 IO Point Number 6 Refer to the I/O templates in this table. Register contents depend on the I/O Point Type. 4480 IO Point Number 7 Refer to the I/O templates in this table. Register contents depend on the I/O Point Type. 4510 IO Point Number 8 Refer to the I/O templates in this table. Register contents depend on the I/O Point Type. 4540 IO Point Number 9 Refer to the I/O templates in this table. Register contents depend on the I/O Point Type. 4570 IO Point Number 10 Refer to the I/O templates in this table. Register contents depend on the I/O Point Type. 4600 IO Point Number 11 Refer to the I/O templates in this table. Register contents depend on the I/O Point Type. 4630 IO Point Number 12 Refer to the I/O templates in this table. Register contents depend on the I/O Point Type. 4660 IO Point Number 13 Refer to the I/O templates in this table. Register contents depend on the I/O Point Type. 4690 IO Point Number 14 Refer to the I/O templates in this table. Register contents depend on the I/O Point Type. 4720 IO Point Number 15 Refer to the I/O templates in this table. Register contents depend on the I/O Point Type. 4750 IO Point Number 16 Refer to the I/O templates in this table. Register contents depend on the I/O Point Type. 4780 IO Point Number 17 Refer to the I/O templates in this table. Register contents depend on the I/O Point Type. 4810 IO Point Number 18 Refer to the I/O templates in this table. © 2006 Schneider Electric All Rights Reserved 160 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–4: Registers for Inputs and Outputs Reg Name Scale Units Range Notes 4840 Reserved — — — Reserved for future development Discrete Input Template First digit (1) indicates point is discrete input Second digit indicates module type 0 = Generic discrete input Base IO Point Type — — 100 – 199 Third digit indicates input type 1 = Unused 2 = AC/DC Base +1 IO Point Label — — ASCII 16 Characters 0 = Normal (default) 1 = Demand Interval Sync Pulse 2 = N/A 3 = Conditional Energy Control 4 = Input Metering, used only with external option modules Discrete Input Base +9 — — 0 – 3 Operating Mode Only one Time Sync input and one Conditional Energy Control are allowed. If the user attempts to configure more than one of each of these modes, the lowest I/O Point Number takes precedence. The modes of the other points will be set to default. Bitmap indicating Demand System(s) to which input is assigned. (Default = 0) Bit 00 = Power Demand Bit 01 = Current Demand Bit 02 = NA Bit 03 = Input Metering Demand Demand Interval Sync Base +10 — — 0x0000 – 0x001F Bit 04 = Generic Demand 1 System Assignments Only one Demand Sync Pulse is allowed per Demand System. If the user attempts to configure more than one input for each system, the lowest I/O Point Number takes precedence. The corresponding bits of the other points are set to 0. Base +11 Reserved — — — Reserved for future development Up to 5 channels are supported Default = 0 Bit 00 = Channel 1 Bit 01 = Channel 2 Metering Pulse Base +14 — — 0x0000 – 0x001F Channel Assignments Bit 02 = Channel 3 Bit 03 = Channel 4 Bit 04 = Channel 5 Bit 05 – 15 Unused © 2006 Schneider Electric All Rights Reserved 161 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–4: Registers for Inputs and Outputs Reg Name Scale Units Range Notes Pulse weight associated with the change of Metering Pulse Weight Base +15 — 1.0 1– 32,767 state of the input. Used for demand metering. Demand (Default = 1) Pulse weight scale factor (power of 10) to apply Metering Pulse Scale Base +16 — 1.0 -3 – 3 to metering pulse weight. Used for demand Factor Demand metering. (Default = 0) Pulse weight associated with the change of Metering Pulse Weight Base +17 — 1.0 1– 32,767 state of the input. Used for consumption Consumption metering. (Default = 1) Metering Pulse Scale Pulse weight scale factor (power of 10) to apply Factor Base +18 — 1.0 -3 – 3 to metering pulse weight. Used for consumption metering. (Default = 0) Consumption Consumption Units See Defines the units associated with the Base +19 — 0 - 100 Code Template Consumption Pulse Weight/Scale (Default = 0) Base +20 Reserved — — — Reserved for future development 0 = OK, 1 = Error IO Point Diagnostic Base +22 — — 0x0000 – 0xFFFF Bit 00 = I/O Point diagnostic summary Bitmap Bit 01 = Configuration invalid – default value used Base +23 Reserved — — — Reserved for future development 0 = Off Discrete Input On/Off Base +25 — — 0 – 1 Status 1 = On Number of times input has transitioned from Off Base +26 Count — — 0 – 99,999,999 to On Base +28 On Time — Seconds 0 – 99,999,999 Duration that discrete input has been On Discrete Output Template First digit (2) indicates point is discrete output Second digit indicates module type 0 = Generic discrete output Base IO Point Type — — 200 – 299 Third digit indicates output type 1 = solid state relay 2 = electromechanical relay Base +1 IO Point Label — — ASCII 16 Characters © 2006 Schneider Electric All Rights Reserved 162 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–4: Registers for Inputs and Outputs Reg Name Scale Units Range Notes 0 = Normal (default) 1 = Latched 2 = Timed 11 = End of power demand interval The following modes are only supported by the standard output (KY). No support is provided for the I/O option modules: Discrete Output Base +9 — — 0 – 11 3 = Absolute kWh pulse Operating Mode 4 = Absolute kVARh pulse 5 = kVAh pulse 6 = kWh In pulse 7 = kVArh In pulse 8 = kWh out pulse 9 = kVARh out pulse 10 = Register-based pulse (future) The time for the output to remain energized On Time For Timed Base +10 — Seconds 1 – 32,767 when the output is in timed mode or end of Mode power demand interval. (Default = 1) kWh / Pulse kVArH / Pulse Specifies the kWh, kVARh and kVAh per pulse Base +11 Pulse Weight — 1 – 32,767 for output when in these modes. (Default = 1) kVAH / Pulse in 100ths 0 = Internal Control Internal/External Base +12 — — 0 – 1 Control 1 = External Control (default) 0 = Normal Control (default) Normal/Override Base +13 — — 0 – 1 Control 1 = Override Control Base +14 Reference Register — — — Reserved for future development Base +15 Reserved — — — Reserved for future development Base +16 Reserved — — — Reserved for future development Base +17 Reserved — — — Reserved for future development Base +18 Reserved — — — Reserved for future development Base +19 Reserved — — — Reserved for future development Base +20 Reserved — — — Reserved for future development State of Discrete Indicates On/Off state of the discrete output Base +21 — — 0 – 1 Output at Reset when meter reset/shutdown occurs © 2006 Schneider Electric All Rights Reserved 163 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–4: Registers for Inputs and Outputs Reg Name Scale Units Range Notes 0 = OK, 1 = Error Bit 00 = I/O Point diagnostic summary Bit 01 = Configuration invalid – default value used IO Point Diagnostic Base +22 — — 0x0000 – 0x000F Bit 02 = Discrete output energy pulse – time Bitmap between transitions exceeds 30 seconds Bit 03 = Discrete output energy pulse – time between transitions limited to 20 milliseconds Base +23 Reserved — — — Reserved for future development Base +24 Reserved — — — Reserved for future development 0 = Off Discrete Output On/Off Base +25 — — 0 – 1 Status 1 = On Number of times output has transitioned from Base +26 Count — — 0 – 99,999,999 OFF to ON Base +28 On Time — Seconds 0 – 99,999,999 Duration that discrete output has been ON © 2006 Schneider Electric All Rights Reserved 164 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–4: Registers for Inputs and Outputs Reg Name Scale Units Range Notes Analog Input Template First digit (3) = point is analog input Second digit = range of analog I/O values (used without units) 0 = 0 – 1 1 = 0 – 5 2 = 0 – 10 3 = 0 – 20 4 = 1 – 5 5 = 4 – 20 6 = -5 – 5 7 = -10 – 10 8 = -100 – 100 9 = User defined (values default to 0) Third digit = digital resolution of the I/O Base IO Point Type — — 300 – 399 hardware. The user must select from one of these standard ranges. 0 = 8-Bit, unipolar 1 = 10-Bit, unipolar 2 = 12-Bit, unipolar 3 = 14-Bit, unipolar 4 = 16-Bit, unipolar 5 = 16-Bit, bipolar with sign 6 = reserved 7 = reserved 8 = Resolution for IO2222 Voltage range 0 - 4000 9 = Resolution for IO2222 Current range 800 - 4000 Base +1 IO Point Label — — ASCII 16 Characters Placeholder for a code used by software to Base +9 Units Code — — 0 – 99 identify the SI units of the analog input being metered, i.e. kW, V, etc. Placeholder for the scale code (power of 10) Base +10 Scale Code — — -3 – 3 used by software to place the decimal point. Analog input gain select. Applies only to Option Module 2222. Base +11 Range Select — — 0 – 1 1 = Use calibration constants associated with current (Default) 0 = Use calibration constants associated with voltage Minimum value of the scaled register value for Base +12 Analog Input Minimum — — 0 – ±32,767 the analog input. (Only if Metering Register Number is not 0.) Maximum value of the scaled register value for Base +13 Analog Input Maximum — — 0 – ±32,767 the analog input. (Only if Metering Register Number is not 0.) © 2006 Schneider Electric All Rights Reserved 165 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–4: Registers for Inputs and Outputs Reg Name Scale Units Range Notes Lower Limit Lower limit of the analog input value. Default Base +14 — — 0 – ±327 value based on I/O Point Type. Analog Value Upper Limit Upper limit of the analog input value. Default Base +15 — — 0 – ±327 value based on I/O Point Type. Analog Value Lower Limit Lower limit of the register value associated with Base +16 — — 0 – ±32,767 the lower limit of the analog input value. Register Value Upper Limit Upper limit of the register value associated with Base +17 — — 0 – ±32,767 the upper limit of the analog input value. Register Value Base +18 Reserved — — — Reserved for future development Analog input user gain adjustment in 100ths of a Base +19 User Gain Adjustment — 0.0001 8,000 – 12,000 percent. Default = 10,000. Analog input user offset adjustment in Bits of Base +20 User Offset Adjustment — — 0 – ±30,000 digital resolution. Default = 0. Base +21 Reserved — — — Reserved for future development 0 = OK, 1 = Error IO Point Diagnostic Base +22 — — 0x0000 – 0x0007 Bit 00 = I/O Point diagnostic summary Bitmap Bit 01 = Configuration invalid – default value used Lower limit of the digital value associated with Lower Limit Base +23 — — 0 – ±32,767 the lower limit of the analog input value. Value Digital Value based on I/O Point Type. Upper limit of the digital value associated with Upper Limit Base +24 — — 0 – ±32,767 the upper limit of the analog input value. Value Digital Value based on I/O Point Type. Base +25 Present Raw Value — — 0 – ±32,767 Raw digital value read from analog input. Raw value corrected by calibration gain and Base +26 Present Scaled Value — — 0 – ±32,767 offset adjustments and scaled based on range of register values. Base +27 Calibration Offset — — 0 – ±32,767 Analog input offset adjustment Calibration Gain Base +28 — 0.0001 8,000 – 12,000 Analog input gain adjustment (Voltage) Calibration Gain Base +29 — 0.0001 8,000 – 12,000 Analog input gain adjustment (Current) © 2006 Schneider Electric All Rights Reserved 166 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–4: Registers for Inputs and Outputs Reg Name Scale Units Range Notes Analog Output Template First digit (4) indicates point is analog output Second digit indicates the range of analog I/O values (used without units) 0 = 0 – 1 1 = 0 – 5 2 = 0 – 10 3 = 0 – 20 4 = 1 – 5 5 = 4 – 20 6 = -5 – 5 7 = -10 – 10 8 = -100 – 100 9 = User defined (values default to 0) Third digit indicates the digital resolution of Base IO Point Type — — 400 – 499 the I/O hardware. The user must select from one of these standard ranges. 0 = 8-Bit, unipolar 1 = 10-Bit, unipolar 2 = 12-Bit, unipolar 3 = 14-Bit, unipolar 4 = 16-Bit, unipolar 5 = 16-Bit, bipolar with sign 6 = reserved 7 = reserved 8 = Resolution for IO2222 Voltage range 0 - 4000 9 = Resolution for IO2222 Current range 800 - 4000 Base +1 IO Point Label — — ASCII 16 Characters Base +9 Reserved — — — Reserved for future development Base +10 Reserved — — — Reserved for future development Base +11 Reserved — — — Reserved for future development 0 = Enable (default) Base +12 Output Enable — — 0 – 1 1 = Disable Base +13 Reserved — — — Reserved for future development Lower Limit Analog Lower limit of the analog output value. Default Base +14 — — 0 – ±327 Value value based on I/O Point Type. Upper Limit Analog Upper limit of the analog output value. Default Base +15 — — 0 – ±327 Value value based on I/O Point Type. Lower Limit Register Lower limit of the register value associated with Base +16 — — 0 – ±32,767 Value the lower limit of the analog output value. Upper Limit Register Upper limit of the register value associated with Base +17 — — 0 – ±32,767 Value the upper limit of the analog output value. Reference Register Register location of value upon which to base Base +18 — — 1000 – 32000 Number the analog output. © 2006 Schneider Electric All Rights Reserved 167 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–4: Registers for Inputs and Outputs Reg Name Scale Units Range Notes Analog output user gain adjustment in 100ths of Base +19 User Gain Adjustment — 0.0001 8000 – 12,000 a percent. Default = 10,000. Analog output user offset adjustment in Bit s of Base +20 User Offset Adjustment — — 0 – ±30000 digital resolution. Default = 0. Base +21 Reserved — — — Reserved for future development 0 = OK, 1 = Error IO Point Diagnostic Base +22 — — 0x0000 – 0xFFFF Bit 00 = I/O Point diagnostic summary Bitmap Bit 01 = Configuration invalid – default value used Lower limit of the digital value associated with Lower Limit Digital Base +23 — — 0 – ±32,767 the lower limit of the analog output value. Value Value based on I/O Point Type. Upper limit of the digital value associated with Upper Limit Digital Base +24 — — 0 – ±32,767 the upper limit of the analog output value. Value Value based on I/O Point Type. Analog value expected to be present at the Base +25 Present Analog Value — 0.01 0 – ±32,767 output terminals of the analog output module. Present Raw Base +26 — — 0 – ±32,767 Value in Reference Register. (Register) Value Analog output offset adjustment in bits of digital Base +27 Calibration Offset — — 0 – ±32,767 resolution. Calibration Gain Analog output gain adjustment in 100ths of a Base +28 — 0.0001 8000 – 12,000 (Voltage) percent. Base +29 Present Digital Value — — — Table A–5: Registers for Alarm Logs Reg Name Scale Units Range Notes Active Alarm Log Bits 0 -7 = Alarm Number Bits 8 = Active/Inactive 0=active 1=inactive Bits 9-11 = Unused Acknowledge/Relay/Pri 5850 — — Bits 12-13 = Priority ority Entry 1 Bit 14 = relay (1 = association) Bit 15 = Alarm Acknowledge (1 = acknowledged) Bits 00 – 07 = Level (0 – 9) 5851 Unique Identifier — — 0 – 0xFFFFFFFF Bits 08 – 15 = Alarm Type Bits 16 – 31 = Test Register 5853 Label — — ASCII 16 Characters Pickup Value for Entry 5861 A-F Units/Scale 0 – 32,767 Does not apply to digital or unary alarms 1 © 2006 Schneider Electric All Rights Reserved 168 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–5: Registers for Alarm Logs Reg Name Scale Units Range Notes Pickup Date/Time Table A–1 Table A–1 5862 — Entry 1 on page 123 on page 123 Active Alarm Log Entry 5865 Same as 5850 – 5864 except for entry 2 2 Active Alarm Log Entry 5880 Same as 5850 – 5864 except for entry 3 3 Active Alarm Log Entry 5895 Same as 5850 – 5864 except for entry 4 4 Active Alarm Log Entry 5910 Same as 5850 – 5864 except for entry 5 5 Active Alarm Log Entry 5925 Same as 5850 – 5864 except for entry 6 6 Active Alarm Log Entry 5940 Same as 5850 – 5864 except for entry 7 7 Active Alarm Log Entry 5955 Same as 5850 – 5864 except for entry 8 8 Active Alarm Log Entry 5970 Same as 5850 – 5864 except for entry 9 9 Active Alarm Log Entry 5985 Same as 5850 – 5864 except for entry 10 10 Active Alarm Log Entry 6000 Same as 5850 – 5864 except for entry 11 11 Active Alarm Log Entry 6015 Same as 5850 – 5864 except for entry 12 12 Active Alarm Log Entry 6030 Same as 5850 – 5864 except for entry 13 13 Active Alarm Log Entry 6045 Same as 5850 – 5864 except for entry 14 14 Active Alarm Log Entry 6060 Same as 5850 – 5864 except for entry 15 15 Active Alarm Log Entry 6075 Same as 5850 – 5864 except for entry 16 16 Active Alarm Log Entry 6090 Same as 5850 – 5864 except for entry 17 17 Active Alarm Log Entry 6105 Same as 5850 – 5864 except for entry 18 18 Active Alarm Log Entry 6120 Same as 5850 – 5864 except for entry 19 19 Active Alarm Log Entry 6135 Same as 5850 – 5864 except for entry 20 20 Active Alarm Log Entry 6150 Same as 5850 – 5864 except for entry 21 21 Active Alarm Log Entry 6165 Same as 5850 – 5864 except for entry 22 22 Active Alarm Log Entry 6180 Same as 5850 – 5864 except for entry 23 23 Active Alarm Log Entry 6195 Same as 5850 – 5864 except for entry 24 24 © 2006 Schneider Electric All Rights Reserved 169 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–5: Registers for Alarm Logs Reg Name Scale Units Range Notes Active Alarm Log Entry 6210 Same as 5850 – 5864 except for entry 25 25 Number of The number of active alarms added to the active unacknowledged 6225 — 1.0 0 – 50 alarm log since reset that have not been alarms in active alarm acknowledged log Number of unacknowledged The number of alarms that have not been 6226 — 1.0 0 – 50 alarms in active alarm acknowledged since reset list Alarm History Log Bits 0 -7 = Alarm Number Bits 8-11 = Unused Acknowledge/Relay/Pri 6250 — — Bits 12-13 = Priority ority Entry 1 Bit 14 = relay (1 = association) Bit 15 = Alarm Acknowledged Bits 00 – 07 = Level (0 – 9) 6251 Unique Identifier — — 0 – 0xFFFFFFFF Bits 08 – 15 = Alarm Type Bits 16 – 31 = Test Register 6253 Label — — ASCII 16 Characters Extreme Value for 6261 A-F Units/Scale 0 – 32,767 Does not apply to digital or unary alarms History Log Entry 1 Dropout Date/Time Table A–1 Table A–1 6262 — Entry 1 on page 123 on page 123 Elapsed Seconds for 6265 — Seconds 0 – 2147483647 History Log Entry 1 Alarm History Log 6267 Same as 6250 – 6266 except for entry 2 Entry 2 Alarm History Log 6284 Same as 6250 – 6266 except for entry 3 Entry 3 Alarm History Log 6301 Same as 6250 – 6266 except for entry 4 Entry 4 Alarm History Log 6318 Same as 6250 – 6266 except for entry 5 Entry 5 Alarm History Log 6335 Same as 6250 – 6266 except for entry 6 Entry 6 Alarm History Log 6352 Same as 6250 – 6266 except for entry 7 Entry 7 Alarm History Log 6369 Same as 6250 – 6266 except for entry 8 Entry 8 Alarm History Log 6386 Same as 6250 – 6266 except for entry 9 Entry 9 Alarm History Log 6403 Same as 6250 – 6266 except for entry 10 Entry 10 Alarm History Log 6420 Same as 6250 – 6266 except for entry 11 Entry 11 © 2006 Schneider Electric All Rights Reserved 170 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–5: Registers for Alarm Logs Reg Name Scale Units Range Notes Alarm History Log 6437 Same as 6250 – 6266 except for entry 12 Entry 12 Alarm History Log 6454 Same as 6250 – 6266 except for entry 13 Entry 13 Alarm History Log 6471 Same as 6250 – 6266 except for entry 14 Entry 14 Alarm History Log 6488 Same as 6250 – 6266 except for entry 15 Entry 15 Alarm History Log 6505 Same as 6250 – 6266 except for entry 16 Entry 16 Alarm History Log 6522 Same as 6250 – 6266 except for entry 17 Entry 17 Alarm History Log 6539 Same as 6250 – 6266 except for entry 18 Entry 18 Alarm History Log 6556 Same as 6250 – 6266 except for entry 19 Entry 19 Alarm History Log 6573 Same as 6250 – 6266 except for entry 20 Entry 20 Alarm History Log 6590 Same as 6250 – 6266 except for entry 21 Entry 21 Alarm History Log 6607 Same as 6250 – 6266 except for entry 22 Entry 22 Alarm History Log 6624 Same as 6250 – 6266 except for entry 23 Entry 23 Alarm History Log 6641 Same as 6250 – 6266 except for entry 24 Entry 24 Alarm History Log 6658 Same as 6250 – 6266 except for entry 25 Entry 25 Number of unacknowledged The number of unacknowledged alarms added 6675 — 1.0 0 – 50 alarms in alarm history to the alarm history log since reset log The number of alarm pickups FIFOed from the 6676 Lost Alarms — 1.0 0 – 32767 internal active alarm list before a correlating pickup is received © 2006 Schneider Electric All Rights Reserved 171 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–6: Registers for Alarm Position Counters Reg Name Scale Units Range Notes Alarms Alarms — System Status 0 = Inactive, 1 = Active 0x0000 – 10011 Active Alarm Map — Binary 0xFFFF Bit00 = Alarm #01 Bit01 = Alarm #02 … … etc. Bit00 = 1 if any priority 1-3 alarm is active Bit01 = 1 if a “High” (1) priority alarm is active 0x0000 – 10023 Active Alarm Status — Binary 0x000F Bit02 = 1 if a “Medium” (2) priority alarm is active Bit03 = 1 if a “Low” (3) priority alarm is active Latched Active Alarms: (from the last time the register was cleared) Latched Active Alarm 0x0000 – 10024 —Binary Bit00 = 1 if any priority 1-3 alarm is active Status 0x000F Bit01 = 1 if a “High” (1) priority alarm is active Bit02 = 1 if a “Medium” (2) priority alarm is active Bit03 = 1 if a “Low” (3) priority alarm is active Total alarm counter, including all priorities 1, 2 and 10025 Total Counter — 1.0 0 – 32,767 3 10026 P3 Counter — 1.0 0 – 32,767 Low alarm counter, all priority 3s 10027 P2 Counter — 1.0 0 – 32,767 Medium alarm counter, all priority 2s 10028 P1 Counter — 1.0 0 – 32,767 High alarm counter, all priority 1s Selection of absolute or relative pickup test for each of the alarm positions (if applicable, based on type) Alarm #01 is least significant bit in register 10040 10029 Pickup Mode Selection — Binary 0x0 – 0xFFFF 0 = Absolute (default) 1 = Relative Bit00 = Alarm #01 Bit01 = Alarm #02, etc. Number of 1-second update intervals used to Number Of Samples In compute the RMS average value used in relative 10041 Relative Threshold — 1.0 5 – 30 pickup alarms Average (Default = 30) Alarms — Counters Alarm Position #001 10115 — 1.0 0 – 32,767 Standard Speed Alarm Position #001 Counter Alarm Position #002 10116 — 1.0 0 – 32,767 Standard Speed Alarm Position #002 Counter Alarm Position #003 10117 — 1.0 0 – 32,767 Standard Speed Alarm Position #003 Counter © 2006 Schneider Electric All Rights Reserved 172 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–6: Registers for Alarm Position Counters Reg Name Scale Units Range Notes Alarm Position #004 10118 — 1.0 0 – 32,767 Standard Speed Alarm Position #004 Counter Alarm Position #005 10119 — 1.0 0 – 32,767 Standard Speed Alarm Position #005 Counter Alarm Position #006 10120 — 1.0 0 – 32,767 Standard Speed Alarm Position #006 Counter Alarm Position #007 10121 — 1.0 0 – 32,767 Standard Speed Alarm Position #007 Counter Alarm Position #008 10122 — 1.0 0 – 32,767 Standard Speed Alarm Position #008 Counter Alarm Position #009 10123 — 1.0 0 – 32,767 Standard Speed Alarm Position #009 Counter Alarm Position #010 10124 — 1.0 0 – 32,767 Standard Speed Alarm Position #010 Counter Alarm Position #011 10125 — 1.0 0 – 32,767 Standard Speed Alarm Position #011 Counter Alarm Position #012 10126 — 1.0 0 – 32,767 Standard Speed Alarm Position #012 Counter Alarm Position #013 10127 — 1.0 0 – 32,767 Standard Speed Alarm Position #013 Counter Alarm Position #014 10128 — 1.0 0 – 32,767 Standard Speed Alarm Position #014 Counter Alarm Position #015 10129 — 1.0 0 – 32,767 Standard Speed Alarm Position #015 Counter Alarm Position #016 10130 — 1.0 0 – 32,767 Standard Speed Alarm Position #016 Counter Alarm Position #017 10131 — 1.0 0 – 32,767 Standard Speed Alarm Position #017 Counter Alarm Position #018 10132 — 1.0 0 – 32,767 Standard Speed Alarm Position #018 Counter Alarm Position #019 10133 — 1.0 0 – 32,767 Standard Speed Alarm Position #019 Counter Alarm Position #020 10134 — 1.0 0 – 32,767 Standard Speed Alarm Position #020 Counter Alarm Position #021 10135 — 1.0 0 – 32,767 Standard Speed Alarm Position #021 Counter Alarm Position #022 10136 — 1.0 0 – 32,767 Standard Speed Alarm Position #022 Counter Alarm Position #023 10137 — 1.0 0 – 32,767 Standard Speed Alarm Position #023 Counter Alarm Position #024 10138 — 1.0 0 – 32,767 Standard Speed Alarm Position #024 Counter Alarm Position #025 10139 — 1.0 0 – 32,767 Standard Speed Alarm Position #025 Counter Alarm Position #026 10140 — 1.0 0 – 32,767 Standard Speed Alarm Position #026 Counter Alarm Position #027 10141 — 1.0 0 – 32,767 Standard Speed Alarm Position #027 Counter © 2006 Schneider Electric All Rights Reserved 173 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–6: Registers for Alarm Position Counters Reg Name Scale Units Range Notes Alarm Position #028 10142 — 1.0 0 – 32,767 Standard Speed Alarm Position #028 Counter Alarm Position #029 10143 — 1.0 0 – 32,767 Standard Speed Alarm Position #029 Counter Alarm Position #030 10144 — 1.0 0 – 32,767 Standard Speed Alarm Position #030 Counter Alarm Position #031 10145 — 1.0 0 – 32,767 Standard Speed Alarm Position #031 Counter Alarm Position #032 10146 — 1.0 0 – 32,767 Standard Speed Alarm Position #032 Counter Alarm Position #033 10147 — 1.0 0 – 32,767 Standard Speed Alarm Position #033 Counter Alarm Position #034 10148 — 1.0 0 – 32,767 Standard Speed Alarm Position #034 Counter Alarm Position #035 10149 — 1.0 0 – 32,767 Standard Speed Alarm Position #035 Counter Alarm Position #036 10150 — 1.0 0 – 32,767 Standard Speed Alarm Position #036 Counter Alarm Position #037 10151 — 1.0 0 – 32,767 Standard Speed Alarm Position #037 Counter Alarm Position #038 10152 — 1.0 0 – 32,767 Standard Speed Alarm Position #038 Counter Alarm Position #039 10153 — 1.0 0 – 32,767 Standard Speed Alarm Position #039 Counter Alarm Position #040 10154 — 1.0 0 – 32,767 Standard Speed Alarm Position #040 Counter Alarm Position #041 10155 — 1.0 0 – 32,767 Disturbance Alarm Position #001 Counter Alarm Position #042 10156 — 1.0 0 – 32,767 Disturbance Alarm Position #002 Counter Alarm Position #043 10157 — 1.0 0 – 32,767 Disturbance Alarm Position #003 Counter Alarm Position #044 10158 — 1.0 0 – 32,767 Disturbance Alarm Position #004 Counter Alarm Position #045 10159 — 1.0 0 – 32,767 Disturbance Alarm Position #005 Counter Alarm Position #046 10160 — 1.0 0 – 32,767 Disturbance Alarm Position #006 Counter Alarm Position #047 10161 — 1.0 0 – 32,767 Disturbance Alarm Position #007 Counter Alarm Position #048 10162 — 1.0 0 – 32,767 Disturbance Alarm Position #008 Counter Alarm Position #049 10163 — 1.0 0 – 32,767 Disturbance Alarm Position #009 Counter Alarm Position #050 10164 — 1.0 0 – 32,767 Disturbance Alarm Position #010 Counter Alarm Position #051 10165 — 1.0 0 – 32,767 Disturbance Alarm Position #011 Counter © 2006 Schneider Electric All Rights Reserved 174 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–6: Registers for Alarm Position Counters Reg Name Scale Units Range Notes Alarm Position #052 10166 — 1.0 0 – 32,767 Disturbance Alarm Position #012 Counter Alarm Position #053 10167 — 1.0 0 – 32,767 Digital Alarm Position #001 Counter Alarm Position #054 10168 — 1.0 0 – 32,767 Digital Alarm Position #002 Counter Alarm Position #055 10169 — 1.0 0 – 32,767 Digital Alarm Position #003 Counter Alarm Position #056 10170 — 1.0 0 – 32,767 Digital Alarm Position #004 Counter Alarm Position #057 10171 — 1.0 0 – 32,767 Digital Alarm Position #005 Counter Alarm Position #058 10172 — 1.0 0 – 32,767 Digital Alarm Position #006 Counter Alarm Position #059 10173 — 1.0 0 – 32,767 Digital Alarm Position #007 Counter Alarm Position #060 10174 — 1.0 0 – 32,767 Digital Alarm Position #008 Counter Alarm Position #061 10175 — 1.0 0 – 32,767 Digital Alarm Position #009 Counter Alarm Position #062 10176 — 1.0 0 – 32,767 Digital Alarm Position #010 Counter Alarm Position #063 10177 — 1.0 0 – 32,767 Digital Alarm Position #011 Counter Alarm Position #064 10178 — 1.0 0 – 32,767 Digital Alarm Position #012 Counter Alarm Position #065 10179 — 1.0 0 – 32,767 Combinatorial (Boolean) Alarm Position #001 Counter Alarm Position #066 10180 — 1.0 0 – 32,767 Combinatorial (Boolean) Alarm Position #002 Counter Alarm Position #067 10181 — 1.0 0 – 32,767 Combinatorial (Boolean) Alarm Position #003 Counter Alarm Position #068 10182 — 1.0 0 – 32,767 Combinatorial (Boolean) Alarm Position #004 Counter Alarm Position #069 10183 — 1.0 0 – 32,767 Combinatorial (Boolean) Alarm Position #005 Counter Alarm Position #070 10184 — 1.0 0 – 32,767 Combinatorial (Boolean) Alarm Position #006 Counter Alarm Position #071 10185 — 1.0 0 – 32,767 Combinatorial (Boolean) Alarm Position #007 Counter Alarm Position #072 10186 — 1.0 0 – 32,767 Combinatorial (Boolean) Alarm Position #008 Counter Alarm Position #073 10187 — 1.0 0 – 32,767 Combinatorial (Boolean) Alarm Position #009 Counter © 2006 Schneider Electric All Rights Reserved 175 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–6: Registers for Alarm Position Counters Reg Name Scale Units Range Notes Alarms — Standard Speed See “Alarms See “Alarms — — Template Standard Speed Alarm Position #001 - See “Alarms 10200 Alarm Position #001 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #002 - See “Alarms 10220 Alarm Position #002 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #003 - See “Alarms 10240 Alarm Position #003 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #004 - See “Alarms 10260 Alarm Position #004 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #005 -See “Alarms 10280 Alarm Position #005 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #006 - See “Alarms 10300 Alarm Position #006 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #007 - See “Alarms 10320 Alarm Position #007 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #008 - See “Alarms 10340 Alarm Position #008 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #009 - See “Alarms 10360 Alarm Position #009 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #010 - See “Alarms 10380 Alarm Position #010 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #011 - See “Alarms 10400 Alarm Position #011 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #012 - See “Alarms 10420 Alarm Position #012 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #013 - See “Alarms 10440 Alarm Position #013 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 © 2006 Schneider Electric All Rights Reserved 176 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–6: Registers for Alarm Position Counters Reg Name Scale Units Range Notes See “Alarms See “Alarms — — Template Standard Speed Alarm Position #014 - See “Alarms 10460 Alarm Position #014 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #015 - See “Alarms 10480 Alarm Position #015 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #016 - See “Alarms 10500 Alarm Position #016 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #017 - See “Alarms 10520 Alarm Position #017 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #018 - See “Alarms 10540 Alarm Position #018 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #019 - See “Alarms 10560 Alarm Position #019 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #020 - See “Alarms 10580 Alarm Position #020 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #021 - See “Alarms 10600 Alarm Position #021 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #022 - See “Alarms 10620 Alarm Position #022 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #023 - See “Alarms 10640 Alarm Position #023 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #024 - See “Alarms 10660 Alarm Position #024 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #025 - See “Alarms 10680 Alarm Position #025 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #026 - See “Alarms 10700 Alarm Position #026 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 © 2006 Schneider Electric All Rights Reserved 177 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–6: Registers for Alarm Position Counters Reg Name Scale Units Range Notes See “Alarms See “Alarms — — Template Standard Speed Alarm Position #027 - See “Alarms 10720 Alarm Position #027 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #028 - See “Alarms 10740 Alarm Position #028 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #029 - See “Alarms 10760 Alarm Position #029 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #030 - See “Alarms 10780 Alarm Position #030 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #031 - See “Alarms 10800 Alarm Position #031 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #032 - See “Alarms 10820 Alarm Position #032 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #033 - See “Alarms 10840 Alarm Position #033 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #034 - See “Alarms 10860 Alarm Position #034 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #035 - See “Alarms 10880 Alarm Position #035 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #036 - See “Alarms 10900 Alarm Position #036 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #037 - See “Alarms 10920 Alarm Position #037 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #038 - See “Alarms 10940 Alarm Position #038 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Standard Speed Alarm Position #039 - See “Alarms 10960 Alarm Position #039 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 © 2006 Schneider Electric All Rights Reserved 178 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–6: Registers for Alarm Position Counters Reg Name Scale Units Range Notes See “Alarms See “Alarms — — Template Standard Speed Alarm Position #040 - See “Alarms 10980 Alarm Position #040 — Template 1” on 1” on — Template 1” on page 182 page 182 page 182 Alarms — Disturbance See “Alarms See “Alarms — — Template Disturbance Alarm Position #001 - See “Alarms — 11000 Alarm Position #041 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Disturbance Alarm Position #002 - See “Alarms — 11020 Alarm Position #042 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Disturbance Alarm Position #003 - See “Alarms — 11040 Alarm Position #043 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Disturbance Alarm Position #004 - See “Alarms — 11060 Alarm Position #044 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Disturbance Alarm Position #005 - See “Alarms — 11080 Alarm Position #045 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Disturbance Alarm Position #006 - See “Alarms — 11100 Alarm Position #046 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Disturbance Alarm Position #007 - See “Alarms — 11120 Alarm Position #047 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Disturbance Alarm Position #0081 - See “Alarms — 11140 Alarm Position #048 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Disturbance Alarm Position #009 - See “Alarms — 11160 Alarm Position #049 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Disturbance Alarm Position #010 - See “Alarms — 11180 Alarm Position #050 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Disturbance Alarm Position #011 - See “Alarms — 11200 Alarm Position #051 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Disturbance Alarm Position #012 - See “Alarms — 11220 Alarm Position #052 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 © 2006 Schneider Electric All Rights Reserved 179 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–6: Registers for Alarm Position Counters Reg Name Scale Units Range Notes Alarms — Digital See “Alarms See “Alarms — — Template Digital Alarm Position #001 - See “Alarms — 11240 Alarm Position #053 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Digital Alarm Position #002 - See “Alarms — 11260 Alarm Position #054 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Digital Alarm Position #003 - See “Alarms — 11280 Alarm Position #055 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Digital Alarm Position #004 - See “Alarms — 11300 Alarm Position #056 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Digital Alarm Position #005 - See “Alarms — 11320 Alarm Position #057 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Digital Alarm Position #006 - See “Alarms — 11340 Alarm Position #058 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Digital Alarm Position #007 - See “Alarms — 11360 Alarm Position #059 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Digital Alarm Position #008 - See “Alarms — 11380 Alarm Position #060 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Digital Alarm Position #009 - See “Alarms — 11400 Alarm Position #061 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Digital Alarm Position #010 - See “Alarms — 11420 Alarm Position #062 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Digital Alarm Position #011 - See “Alarms — 11440 Alarm Position #063 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 See “Alarms See “Alarms — — Template Digital Alarm Position #012 - See “Alarms — 11460 Alarm Position #064 — Template 1” on 1” on Template 1” on page 182 page 182 page 182 © 2006 Schneider Electric All Rights Reserved 180 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–6: Registers for Alarm Position Counters Reg Name Scale Units Range Notes Alarms — Boolean See “Alarms See “Alarms — Combinatorial (Boolean) Alarm Position #001 — Template 11480 Alarm Position #065 — Template 2” on 2” on See “Alarms — Template 2” on page 183 page 183 page 183 See “Alarms See “Alarms — Combinatorial (Boolean) Alarm Position #002 — Template 11500 Alarm Position #066 — Template 2” on 2” on See “Alarms — Template 2” on page 183 page 183 page 183 See “Alarms See “Alarms — Combinatorial (Boolean) Alarm Position #003 — Template 11520 Alarm Position #067 — Template 2” on 2” on See “Alarms — Template 2” on page 183 page 183 page 183 See “Alarms See “Alarms — Combinatorial (Boolean) Alarm Position #004 — Template 11540 Alarm Position #068 — Template 2” on 2” on See “Alarms — Template 2” on page 183 page 183 page 183 See “Alarms See “Alarms — Combinatorial (Boolean) Alarm Position #005 — Template 11560 Alarm Position #069 — Template 2” on 2” on See “Alarms — Template 2” on page 183 page 183 page 183 See “Alarms See “Alarms — Combinatorial (Boolean) Alarm Position #006 — Template 11580 Alarm Position #070 — Template 2” on 2” on See “Alarms — Template 2” on page 183 page 183 page 183 See “Alarms See “Alarms — Combinatorial (Boolean) Alarm Position #007 — Template 11600 Alarm Position #071 — Template 2” on 2” on See “Alarms — Template 2” on page 183 page 183 page 183 See “Alarms See “Alarms — Combinatorial (Boolean) Alarm Position #008 — Template 11620 Alarm Position #072 — Template 2” on 2” on See “Alarms — Template 2” on page 183 page 183 page 183 See “Alarms See “Alarms — Combinatorial (Boolean) Alarm Position #009 — Template 11640 Alarm Position #073 — Template 2” on 2” on See “Alarms — Template 2” on page 183 page 183 page 183 See “Alarms See “Alarms — Combinatorial (Boolean) Alarm Position #010 — Template 11660 Alarm Position #074 — Template 2” on 2” on See “Alarms — Template 2” on page 183 page 183 page 183 © 2006 Schneider Electric All Rights Reserved 181 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–6: Registers for Alarm Position Counters Reg Name Scale Units Range Notes Alarms — Template 1 Bits 00 – 07 = Level (0 – 9) Bits 08 – 15 = Alarm Type Bits 16 – 31 = Test Register For Disturbance alarms Test Register is: 1 = Vab 2 = Vbc 3 = Vca 4 = Van 5 = Vbn 6 = Vcn 7 = Vng 0 – Base Unique Identifier — — 0xFFFFFFFF 8 = Ia 9 = Ib 10 = Ic 11 = In For Unary Alarms, Test Register is: 1 = End of Incremental Energy Interval 2 = End of Power Demand Interval 3 = End of 1s Meter Update Cycle 4 = Reserved 5 = Power up/ Reset MSB: 0x00 = Disabled (Default) MSB: 0 – FF Base +2 Enable/Disable, Priority — — 0xFF = Enabled LSB: 0 – 3 LSB: Specifies the priority level 0 – 3 Base +3 Label — — ASCII 16 Characters Base +11 Pickup Value A-F Units/Scale 0 – 32,767 Does not apply to digital or unary alarms 0 – 32,767 Standard Speed Alarms Base +12 Pickup Delay — 1s Cycle 0 – 999 Disturbance Alarms 0 – 999 Does not apply to digital or unary alarms. A-F Base +13 Dropout Value Units/Scale 0 – 32,767 Does not apply to digital or unary alarms. — 0 – 32,767 Standard Speed Alarms Base +14 Dropout Delay — 1s Cycle 0 – 999 Disturbance Alarms 0 – 999 Does not apply to digital or unary alarms. Base +15 Reserved — — — Reserved for future development Bit 00 = Datalog #1 0 – Base +16 Datalog Specifier — — Bit 01 = Datalog #2 (PM850, PM870) 0xFFFFFFFF Bit 02 = Datalog #3 (PM850, PM870) © 2006 Schneider Electric All Rights Reserved 182 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–6: Registers for Alarm Position Counters Reg Name Scale Units Range Notes Alarms — Template 2 Bits 00 – 07 = Level (0 – 9) 0 – Base Unique Identifier — — Bits 08 – 15 = Alarm Type 0xFFFFFFFF Bits 16 – 31 = Test Register MSB: 0 – FF MSB: 0x00 = Disable; 0xFF = Enable Base +2 Enable/Disable, Priority — — LSB: 0 – 3 LSB: Specifies the priority level 0 – 3 Base +3 Label — — ASCII 16 Characters Base +11 Alarm test list — — 0 – 74 Alarm test list (position # in the normal alarm list) Table A–7: Abbreviated Floating-Point Register List Reg Name Units Notes 1s Metering – Current 11700 Current, Phase A Amps RMS 11702 Current, Phase B Amps RMS 11704 Current, Phase C Amps RMS RMS 11706 Current, Neutral Amps 4-wire system only RMS 11708 Current, Ground Amps 4-wire system only 11710 Current, 3-Phase Average Amps Calculated mean of Phases A, B & C 1s Metering – Voltage 11712 Voltage, A-B Volts RMS Voltage measured between A & B 11714 Voltage, B-C Volts RMS Voltage measured between B & C 11716 Voltage, C-A Volts RMS Voltage measured between C & A 11718 Voltage, L-L Average Volts RMS 3 Phase Average L-L Voltage RMS Voltage measured between A & N 11720 Voltage, A-N Volts 4-wire system only RMS Voltage measured between B & N 11722 Voltage, B-N Volts 4-wire system only RMS Voltage measured between C & N 11724 Voltage, C-N Volts 4-wire system only RMS Voltage measured between N & G 11726 Voltage, N-G Volts 4-wire system with 4 element metering only 11728 Voltage, L-N Average Volts RMS 3-Phase Average L-N Voltage 1s Metering – Power Real Power (PA) 11730 Real Power, Phase A W 4-wire system only Real Power (PB) 11732 Real Power, Phase B W 4-wire system only Real Power (PC) 11734 Real Power, Phase C W 4-wire system only © 2006 Schneider Electric All Rights Reserved 183 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–7: Abbreviated Floating-Point Register List Reg Name Units Notes 4-wire system = PA+PB+PC 11736 Real Power, Total W 3-wire system = 3-Phase real power Reactive Power (QA) 11738 Reactive Power, Phase A VAr 4-wire system only Reactive Power (QB) 11740 Reactive Power, Phase B VAr 4-wire system only Reactive Power (QC) 11742 Reactive Power, Phase C VAr 4-wire system only 4-wire system = QA+QB+QC 11744 Reactive Power, Total VAr 3 wire system = 3-Phase reactive power Apparent Power (SA) 11746 Apparent Power, Phase A VA 4-wire system only Apparent Power (SB) 11748 Apparent Power, Phase B VA 4-wire system only Apparent Power (SC) 11750 Apparent Power, Phase C VA 4-wire system only 4-wire system = SA+SB+SC 11752 Apparent Power, Total VA 3-wire system = 3-Phase apparent power 1s Metering – Power Factor Derived using the complete harmonic content of real 11754 True Power Factor, Phase A and apparent power. 4-wire system only Derived using the complete harmonic content of real 11756 True Power Factor, Phase B and apparent power. 4-wire system only Derived using the complete harmonic content of real 11758 True Power Factor, Phase C and apparent power. 4-wire system only Derived using the complete harmonic content of real 11760 True Power Factor, Total and apparent power 1s Metering – Frequency Frequency of circuits being monitored. If the 11762 Frequency Hz frequency is out of range, the register will be -32,768. Energy 11800 Energy, Real In WH 3-Phase total real energy into the load 11802 Energy, Reactive In VArH 3-Phase total reactive energy into the load 11804 Energy, Real Out WH 3-Phase total real energy out of the load 11806 Energy, Reactive Out VArH 3-Phase total reactive energy out of the load Energy, Real Total 11808 WH Total Real Energy In, Out or In + Out (signed/absolute) Energy, Reactive Total 11810 VArH Total Reactive Energy In, Out or In + Out (signed/absolute) 11812 Energy, Apparent VAH 3-Phase total apparent energy 3-Phase total accumulated conditional real energy into 11814 Energy, Conditional Real In WH the load Energy, Conditional Reactive 3-Phase total accumulated conditional reactive energy 11816 VArH In into the load © 2006 Schneider Electric All Rights Reserved 184 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–7: Abbreviated Floating-Point Register List Reg Name Units Notes 3-Phase total accumulated conditional real energy out 11818 Energy, Conditional Real Out WH of the load Energy, Conditional Reactive 3-Phase total accumulated conditional reactive energy 11820 VArH Out out of the load 3-Phase total accumulated conditional apparent 11822 Energy, Conditional Apparent VAH energy Energy, Incremental Real In, 3-Phase total accumulated incremental real energy 11824 WH Last Complete Interval into the load Energy. Incremental Reactive 3-Phase total accumulated incremental reactive 11826 VArH In, Last Complete Interval energy into the load Energy, Incremental Real 3-Phase total accumulated incremental real energy 11828 WH Out, Last Complete Interval out of the load Energy, Incremental Reactive 3-Phase total accumulated incremental reactive 11830 VArH Out, Last Complete Interval energy out of the load Energy, Incremental 3-Phase total accumulated incremental apparent 11832 Apparent, Last Complete VAH energy Interval Energy, Incremental Real In, 3-Phase total accumulated incremental real energy 11836 WH Present Interval into the load Energy. Incremental Reactive 3-Phase total accumulated incremental reactive 11838 VArH In, Present Interval energy into the load Energy, Incremental Real 3-Phase total accumulated incremental real energy 11840 WH Out, Present Interval out of the load Energy, Incremental Reactive 3-Phase total accumulated incremental reactive 11842 VArH Out, Present Interval energy out of the load Energy, Incremental 3-Phase total accumulated incremental apparent 11844 VAH Apparent, Present Interval energy 3-Phase total accumulated incremental reactive 11846 Energy, Reactive, Quadrant 1 VArH energy – quadrant 1 3-Phase total accumulated incremental reactive 11848 Energy, Reactive, Quadrant 2 VArH energy – quadrant 2 3-Phase total accumulated incremental reactive 11850 Energy, Reactive, Quadrant 3 VArH energy – quadrant 3 3-Phase total accumulated incremental reactive 11852 Energy, Reactive, Quadrant 4 VArH energy – quadrant 4 Cumulative Usage The user must identify the units to be used in the 11854 (2) Input Channel #1 accumulation. Cumulative Usage The user must identify the units to be used in the 11856 (2) Input Channel #2 accumulation. Cumulative Usage The user must identify the units to be used in the 11858 (2) Input Channel #3 accumulation. Cumulative Usage The user must identify the units to be used in the 11860 (2) Input Channel #4 accumulation. Cumulative Usage The user must identify the units to be used in the 11862 (2) Input Channel #5 accumulation. Energy, Real 3-Phase Total 11864 WH Usage Today Energy, Real 3-Phase Total 11866 WH Usage Yesterday © 2006 Schneider Electric All Rights Reserved 185 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–7: Abbreviated Floating-Point Register List Reg Name Units Notes Energy, Real 3-Phase Total 11868 WH Usage This Week Energy, Real 3-Phase Total 11870 WH Usage Last Week Energy, Real 3-Phase Total 11872 WH Usage This Month Energy, Real 3-Phase Total 11874 WH Usage Last Month Energy, Apparent 3-Phase 11876 Total WH Usage Today Energy, Apparent 3-Phase 11878 Total WH Usage Yesterday Energy, Apparent 3-Phase 11880 Total VAH Usage This Week Energy, Apparent 3-Phase 11882 Total VAH Usage Last Week Energy, Apparent 3-Phase 11884 Total VAH Usage This Month Energy, Apparent 3-Phase 11886 Total VAH Usage Last Month Energy, Real 3-Phase Total 11888 VAH Usage – First Shift – Today Energy, Real 3-Phase Total 11890 Usage – Second Shift – VAH Today Energy, Real 3-Phase Total 11892 VAH Usage – Third Shift – Today Energy, Real 3-Phase Total 11894 Usage – First Shift – VAH Yesterday Energy, Real 3-Phase Total 11896 Usage – Second Shift – WH Yesterday Energy, Real 3-Phase Total 11898 Usage – Third Shift – WH Yesterday Energy, Real 3-Phase Total 11900 Usage – First Shift – This WH Week Energy, Real 3-Phase Total 11902 Usage – Second Shift – This WH Week Energy, Real 3-Phase Total 11904 Usage – Third Shift – This WH Week © 2006 Schneider Electric All Rights Reserved 186 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–7: Abbreviated Floating-Point Register List Reg Name Units Notes Energy, Real 3-Phase Total 11906 Usage – First Shift – Last WH Week Energy, Real 3-Phase Total 11908 Usage – Second Shift – Last WH Week Energy, Real 3-Phase Total 11910 Usage – Third Shift – Last WH Week Energy, Real 3-Phase Total 11912 Usage – First Shift – This WH Month Energy, Real 3-Phase Total 11914 Usage – Second Shift – This WH Month Energy, Real 3-Phase Total 11916 Usage – Third Shift – This WH Month Energy, Real 3-Phase Total 11918 Usage – First Shift – Last WH Month Energy, Real 3-Phase Total 11920 Usage – Second Shift – Last WH Month Energy, Real 3-Phase Total 11922 Usage – Third Shift – Last WH Month Energy, Apparent 3-Phase 11924 Total WH Usage – First Shift – Today Energy, Apparent 3-Phase Total 11926 WH Usage – Second Shift – Today Energy, Apparent 3-Phase 11928 Total WH Usage – Third Shift – Today Energy, Apparent 3-Phase Total 11930 WH Usage – First Shift – Yesterday Energy, Apparent 3-Phase Total 11932 VAH Usage – Second Shift – Yesterday Energy, Apparent 3-Phase Total 11934 VAH Usage – Third Shift – Yesterday Energy, Apparent 3-Phase Total 11936 VAH Usage – First Shift – This Week © 2006 Schneider Electric All Rights Reserved 187 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–7: Abbreviated Floating-Point Register List Reg Name Units Notes Energy, Apparent 3-Phase Total 11938 VAH Usage – Second Shift – This Week Energy, Apparent 3-Phase Total 11940 VAH Usage – Third Shift – This Week Energy, Apparent 3-Phase Total 11942 VAH Usage – First Shift – Last Week Energy, Apparent 3-Phase Total 11944 VAH Usage – Second Shift – Last Week Energy, Apparent 3-Phase Total 11946 VAH Usage – Third Shift – Last Week Energy, Apparent 3-Phase Total 11948 VAH Usage – First Shift – This Month Energy, Apparent 3-Phase Total 11950 VAH Usage – Second Shift – This Month Energy, Apparent 3-Phase Total 11952 VAH Usage – Third Shift – This Month Energy, Apparent 3-Phase Total 11954 VAH Usage – First Shift – Last Month Energy, Apparent 3-Phase Total 11956 VAH Usage – Second Shift – Last Month Energy, Apparent 3-Phase Total 11958 VAH Usage – Third Shift – Last Month Total Harmonic Distortion, Phase A Current 11960 THD/thd Current, Phase A - See register 3227 for THD/ thd definition Total Harmonic Distortion, Phase B Current 11962 THD/thd Current, Phase B - See register 3227 for THD/ thd definition Total Harmonic Distortion, Phase C Current 11964 THD/thd Current, Phase C - See register 3227 for THD/ thd definition Total Harmonic Distortion, Phase N Current 11966 THD/thd Current, Phase N - (4-wire systems and system type and 12 only) See register 3227 for THD/ thd definition © 2006 Schneider Electric All Rights Reserved 188 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–7: Abbreviated Floating-Point Register List Reg Name Units Notes Total Harmonic Distortion Phase A-N 11968 THD/thd Voltage, Phase A-N - (4-wire systems and system types 10 and 12) See register 3227 for THD/ thd definition Total Harmonic Distortion Phase B-N 11970 THD/thd Voltage, Phase B-N - (4-wire systems and system type 12 only) See register 3227 for THD/ thd definition Total Harmonic Distortion Phase C-N 11972 THD/thd Voltage, Phase C-N - (4-wire system only) See register 3227 for THD/ thd definition Total Harmonic Distortion Phase A-B 11974 THD/thd Voltage, Phase A-B - See register 3227 for THD/ thd definition Total Harmonic Distortion Phase B-C 11976 THD/thd Voltage, Phase B-C - See register 3227 for THD/ thd definition Total Harmonic Distortion Phase C-A 11978 THD/thd Voltage, Phase C-A - See register 3227 for THD/ thd definition Table A–8: Spectral Components Reg Name Scale Units Range Notes Spectral Components Spectral Components — Harmonic Magnitudes and Angles See “Spectral See “Spectral See “Spectral Components — Data Template” Harmonic Magnitudes Components — Components — on page 190 13200 and Angles, Voltage A- — Data Template” Data Template” B on page 190 on page 190 See “Spectral See “Spectral See “Spectral Components — Data Template” Harmonic Magnitudes Components — Components — on page 190 13328 and Angles, Voltage B- — Data Template” Data Template” C on page 190 on page 190 See “Spectral See “Spectral Harmonic Magnitudes Components — Components — See “Spectral Components — Data Template” 13456 and Angles, Voltage C- — Data Template” Data Template” on page 190 A on page 190 on page 190 See “Spectral See “Spectral See “Spectral Components — Data Template” Harmonic Magnitudes Components — Components — on page 190 13584 and Angles, Voltage A- — Data Template” Data Template” N on page 190 on page 190 See “Spectral See “Spectral Harmonic Magnitudes Components — Components — See “Spectral Components — Data Template” 13712 and Angles, Voltage B- — Data Template” Data Template” on page 190 N on page 190 on page 190 See “Spectral See “Spectral Harmonic Magnitudes Components — Components — See “Spectral Components — Data Template” 13840 and Angles, Voltage C- — Data Template” Data Template” on page 190 N on page 190 on page 190 © 2006 Schneider Electric All Rights Reserved 189 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–8: Spectral Components Reg Name Scale Units Range Notes See “Spectral See “Spectral Harmonic Magnitudes Components — Components — See “Spectral Components — Data Template” 13968 and Angles, Voltage N- — Data Template” Data Template” on page 190 G on page 190 on page 190 See “Spectral See “Spectral Harmonic Magnitudes Components — Components — See “Spectral Components — Data Template” 14096 and Angles, Current, — Data Template” Data Template” on page 190 Phase A on page 190 on page 190 See “Spectral See “Spectral Harmonic Magnitudes Components — Components — See “Spectral Components — Data Template” 14224 and Angles, Current, — Data Template” Data Template” on page 190 Phase B on page 190 on page 190 See “Spectral See “Spectral Harmonic Magnitudes Components — Components — See “Spectral Components — Data Template” 14352 and Angles, Current, — Data Template” Data Template” on page 190 Phase C on page 190 on page 190 See “Spectral See “Spectral Harmonic Magnitudes Components — Components — See “Spectral Components — Data Template” 14480 and Angles, Current, — Data Template” Data Template” on page 190 Neutral on page 190 on page 190 Spectral Components — Data Template Magnitude of fundamental or overall RMS value which harmonic percentages are based. Volts/Scale 0 – 32,767 Base Reference Magnitude — Format selection is based on the value in Amps/Scale (-32,768 if N/A) register 3241 or 3242. A selection of 2 (RMS) will cause a value of -32768 to be entered. -3 – 3 Base +1 Scale Factor — 1.0 Power of 10 (-32,768 if N/A) % .01 0 – 10000 Magnitude of harmonic expressed as a Base +2 H1 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 1st harmonic referenced to 0 – 3,599 Base +3 H1 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base +4 H2 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 2nd harmonic referenced to 0 – 3,599 Base +5 H2 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base +6 H3 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 3rd harmonic referenced to 0 – 3,599 Base +7 H3 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base +8 H4 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 © 2006 Schneider Electric All Rights Reserved 190 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–8: Spectral Components Reg Name Scale Units Range Notes Angle of 4th harmonic referenced to 0 – 3,599 Base +9 H4 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base +10 H5 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 5th harmonic referenced to 0 – 3,599 Base +11 H5 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base +12 H6 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 6th harmonic referenced to 0 – 3,599 Base +13 H6 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base +14 H7 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 7th harmonic referenced to 0 – 3,599 Base +15 H7 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base +16 H8 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 8th harmonic referenced to 0 – 3,599 Base +17 H8 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 18 H9 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 9th harmonic referenced to 0 – 3,599 Base + 19 H9 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 20 H10 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 10th harmonic referenced to 0 – 3,599 Base + 21 H10 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 22 H11 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 11th harmonic referenced to 0 – 3,599 Base + 23 H11 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). © 2006 Schneider Electric All Rights Reserved 191 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–8: Spectral Components Reg Name Scale Units Range Notes % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 24 H12 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 12th harmonic referenced to 0 – 3,599 Base + 25 H12 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 26 H13 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 13th harmonic referenced to 0 – 3,599 Base + 27 H13 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 28 H14 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 14th harmonic referenced to 0 – 3,599 Base + 29 H14 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 30 H15 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 15th harmonic referenced to 0 – 3,599 Base + 31 H15 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 32 H16 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 16th harmonic referenced to 0 – 3,599 Base + 33 H16 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 34 H17 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 17th harmonic referenced to 0 – 3,599 Base + 35 H17 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 36 H18 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 18th harmonic referenced to 0 – 3,599 Base + 37 H18 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 38 H19 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 © 2006 Schneider Electric All Rights Reserved 192 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–8: Spectral Components Reg Name Scale Units Range Notes Angle of 19th harmonic referenced to 0 – 3,599 Base + 39 H19 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 40 H20 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 20th harmonic referenced to 0 – 3,599 Base + 41 H20 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 42 H21 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 21st harmonic referenced to 0 – 3,599 Base + 43 H21 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 44 H22 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 22nd harmonic referenced to 0 – 3,599 Base + 45 H22 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 46 H23 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 23rd harmonic referenced to 0 – 3,599 Base + 47 H23 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 48 H24 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 24th harmonic referenced to 0 – 3,599 Base + 49 H24 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 50 H25 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 25th harmonic referenced to 0 – 3,599 Base + 51 H25 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 52 H26 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 26th harmonic referenced to 0 – 3,599 Base + 53 H26 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). © 2006 Schneider Electric All Rights Reserved 193 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–8: Spectral Components Reg Name Scale Units Range Notes % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 54 H27 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 27th harmonic referenced to 0 – 3,599 Base + 55 H27 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 56 H28 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 28th harmonic referenced to 0 – 3,599 Base + 57 H28 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 58 H29 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 29th harmonic referenced to 0 – 3,599 Base + 59 H29 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 60 H30 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 30th harmonic referenced to 0 – 3,599 Base + 61 H30 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). % .01 0 – 10000 Magnitude of harmonic expressed as a Base + 62 H31 Magnitude D,E Volts/Scale 0 – 32,767 percentage of the reference value, or as an absolute value. A,B Amps/Scale 0 – 32,767 Angle of 31st harmonic referenced to 0 – 3,599 Base + 63 H31 Angle — 0.1 ° fundamental Voltage A-N (4-wire) or Voltage (-32,678 if N/A) A-B (3-wire). Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 64 H32 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 32nd harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 65 H32 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 66 H33 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 33rd harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 67 H33 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. © 2006 Schneider Electric All Rights Reserved 194 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–8: Spectral Components Reg Name Scale Units Range Notes Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 68 H34 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 34th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 69 H34 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 70 H35 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 35th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 71 H35 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 72 H36 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 36th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 73 H36 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 74 H37 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 37th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 75 H37 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 76 H38 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 38th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 77 H38 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 78 H39 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 39th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 79 H39 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. © 2006 Schneider Electric All Rights Reserved 195 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–8: Spectral Components Reg Name Scale Units Range Notes Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 80 H40 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 40th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 81 H40 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 82 H41 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 41st harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 83 H41 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 84 H42 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 42nd harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 85 H42 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 86 H43 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 43rd harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 87 H43 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 88 H44 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 44th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 89 H44 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 90 H45 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 45th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 91 H45 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. © 2006 Schneider Electric All Rights Reserved 196 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–8: Spectral Components Reg Name Scale Units Range Notes Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 92 H46 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 46th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 93 H46 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 94 H47 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 47th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 95 H47 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 96 H48 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 48th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 97 H48 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + 98 H49 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 49th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + 99 H49 Angle — 0.1 ° A-B (3-wire). (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + H50 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. 100 A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 50th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + H50 Angle — 0.1 ° A-B (3-wire). 101 (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + H51 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. 102 A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 51st harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + H51 Angle — 0.1 ° A-B (3-wire). 103 (-32,678 if N/A) NOTE: PM850 and PM870 only. © 2006 Schneider Electric All Rights Reserved 197 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–8: Spectral Components Reg Name Scale Units Range Notes Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + H52 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. 104 A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 52nd harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + H52 Angle — 0.1 ° A-B (3-wire). 105 (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + H53 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. 106 A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 53rd harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + H53 Angle — 0.1 ° A-B (3-wire). 107 (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + H54 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. 108 A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 54th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + H54 Angle — 0.1 ° A-B (3-wire). 109 (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + H55 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. 110 A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 55th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + H55 Angle — 0.1 ° A-B (3-wire). 111 (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + H56 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. 112 A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 56th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + H56 Angle — 0.1 ° A-B (3-wire). 113 (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + H57 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. 114 A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 57th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + H57 Angle — 0.1 ° A-B (3-wire). 115 (-32,678 if N/A) NOTE: PM850 and PM870 only. © 2006 Schneider Electric All Rights Reserved 198 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–8: Spectral Components Reg Name Scale Units Range Notes Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + H58 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. 116 A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 58th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + H58 Angle — 0.1 ° A-B (3-wire). 117 (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + H59 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. 118 A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 59th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + H59 Angle — 0.1 ° A-B (3-wire). 119 (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + H60 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. 120 A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 60th harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + H60 Angle — 0.1 ° A-B (3-wire). 121 (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + H61 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. 122 A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 61st harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + H61 Angle — 0.1 ° A-B (3-wire). 123 (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + H62 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. 124 A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 62nd harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + H62 Angle — 0.1 ° A-B (3-wire). 125 (-32,678 if N/A) NOTE: PM850 and PM870 only. Magnitude of harmonic expressed as a % .01 0 – 10000 percentage of the reference value, or as an Base + H63 Magnitude D,E Volts/Scale 0 – 32,767 absolute value. 126 A,B Amps/Scale 0 – 32,767 NOTE: PM850 and PM870 only. Angle of 63rd harmonic referenced to 0 – 3,599 fundamental Voltage A-N (4-wire) or Voltage Base + H63 Angle — 0.1 ° A-B (3-wire). 127 (-32,678 if N/A) NOTE: PM850 and PM870 only. © 2006 Schneider Electric All Rights Reserved 199 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–9: Energy Registers Reg Name Units Range Notes Energy Summary Usage Energy, Real 3-Phase Total 16202 WH (1) Usage Today Energy, Real 3-Phase Total 16205 WH (1) Usage Yesterday Energy, Real 3-Phase Total 16208 WH (1) Usage This Week Energy, Real 3-Phase Total 16211 WH (1) Usage Last Week Energy, Real 3-Phase Total 16214 WH (1) Usage This Month Energy, Real 3-Phase Total 16217 WH (1) Usage Last Month Energy, Apparent 3-Phase Total 16220 VAH (1) Usage Today Energy, Apparent 3-Phase Total 16223 VAH (1) Usage Yesterday Energy, Apparent 3-Phase Total 16226 VAH (1) Usage This Week Energy, Apparent 3-Phase Total 16229 VAH (1) Usage Last Week Energy, Apparent 3-Phase Total 16232 VAH (1) Usage This Month Energy, Apparent 3-Phase Total 16235 VAH (1) Usage Last Month Energy Per Shift Usage Energy, Real 3-Phase Total 16238 WH Usage – First Shift - Today Energy, Real 3-Phase Total 16241 WH (1) Usage - Second Shift - Today Energy, Real 3-Phase Total 16244 WH (1) Usage - Third Shift - Today Energy, Real 3-Phase Total 16247 WH (1) Usage - First Shift - Yesterday Energy, Real 3-Phase Total 16250 WH (1) Usage - Second Shift - Yesterday Energy, Real 3-Phase Total 16253 WH (1) Usage - Third Shift - Yesterday Energy, Real 3-Phase Total 16256 WH (1) Usage - First Shift - This Week Energy, Real 3-Phase Total 16259 Usage - Second Shift - This WH (1) Week Energy, Real 3-Phase Total 16262 WH (1) Usage - Third Shift - This Week Energy, Real 3-Phase Total 16265 WH (1) Usage - First Shift - Last Week © 2006 Schneider Electric All Rights Reserved 200 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–9: Energy Registers Reg Name Units Range Notes Energy, Real 3-Phase Total 16268 Usage - Second Shift - Last WH (1) Week Energy, Real 3-Phase Total 16271 WH (1) Usage - Third Shift - Last Week Energy, Real 3-Phase Total 16274 WH (1) Usage - First Shift - This Month Energy, Real 3-Phase Total 16277 Usage - Second Shift - This WH (1) Month Energy, Real 3-Phase Total 16280 WH (1) Usage - Third Shift - This Month Energy, Real 3-Phase Total 16283 WH (1) Usage - First Shift - Last Month Energy, Real 3-Phase Total 16286 Usage - Second Shift - Last WH (1) Month Energy, Real 3-Phase Total 16289 WH (1) Usage - Third Shift - Last Month Energy, Apparent 3-Phase Total 16292 VAH (1) Usage - First Shift - Today Energy, Apparent 3-Phase Total 16295 VAH (1) Usage - Second Shift - Today Energy, Apparent 3-Phase Total 16298 VAH (1) Usage - Third Shift - Today Energy, Apparent 3-Phase Total 16301 VAH (1) Usage - First Shift - Yesterday Energy, Apparent 3-Phase Total 16304 VAH (1) Usage - Second Shift - Yesterday Energy, Apparent 3-Phase Total 16307 VAH (1) Usage - Third Shift - Yesterday Energy, Apparent 3-Phase Total 16310 VAH (1) Usage - First Shift - This Week Energy, Apparent 3-Phase Total 16313 Usage - Second Shift - This VAH (1) Week Energy, Apparent 3-Phase Total 16316 VAH (1) Usage - Third Shift - This Week Energy, Apparent 3-Phase Total 16319 VAH (1) Usage - First Shift - Last Week Energy, Apparent 3-Phase Total 16322 Usage - Second Shift - Last VAH (1) Week Energy, Apparent 3-Phase Total 16325 VAH (1) Usage - Third Shift - Last Week Energy, Apparent 3-Phase Total 16328 VAH (1) Usage - First Shift - This Month © 2006 Schneider Electric All Rights Reserved 201 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 Table A–9: Energy Registers Reg Name Units Range Notes Energy, Apparent 3-Phase Total 16331 Usage - Second Shift - This VAH (1) Month Energy, Apparent 3-Phase Total 16334 VAH (1) Usage - Third Shift - This Month Energy, Apparent 3-Phase Total 16337 VAH (1) Usage - First Shift - Last Month Energy, Apparent 3-Phase Total 16340 Usage - Second Shift - Last VAH (1) Month Energy, Apparent 3-Phase Total 16343 VAH (1) Usage - Third Shift - Last Month Energy Per Shift Cost Energy Cost - First Shift 16348 Unit Code Units associated with the cost per kWH. Today Energy Cost - Second Shift 16350 Unit Code Units associated with the cost per kWH. Today Energy Cost - Third Shift 16352 Unit Code Units associated with the cost per kWH. Today Energy Cost - First Shift 16354 Unit Code Units associated with the cost per kWH. Yesterday Energy Cost - Second Shift 16356 Unit Code Units associated with the cost per kWH. Yesterday Energy Cost - Third Shift 16358 Unit Code Units associated with the cost per kWH. Yesterday Energy Cost - First Shift 16360 Unit Code Units associated with the cost per kWH. This Week Energy Cost - Second Shift 16362 Unit Code Units associated with the cost per kWH. This Week Energy Cost - Third Shift 16364 Unit Code Units associated with the cost per kWH. This Week Energy Cost - First Shift 16366 Unit Code Units associated with the cost per kWH. Last Week Energy Cost - Second Shift 16368 Unit Code Units associated with the cost per kWH. Last Week Energy Cost - Third Shift 16370 Unit Code Units associated with the cost per kWH. Last Week Energy Cost - First Shift 16372 Unit Code Units associated with the cost per kWH. This Month Energy Cost - Second Shift 16374 Unit Code Units associated with the cost per kWH. This Month Energy Cost - Third Shift 16376 Unit Code Units associated with the cost per kWH. This Month Energy Cost - First Shift 16378 Unit Code Units associated with the cost per kWH. Last Month © 2006 Schneider Electric All Rights Reserved 202 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix A—Power Meter Register List Table A–9: Energy Registers Reg Name Units Range Notes Energy Cost - Second Shift 16380 Unit Code Units associated with the cost per kWH. Last Month Energy Cost - Third Shift 16382 Unit Code Units associated with the cost per kWH. Last Month © 2006 Schneider Electric All Rights Reserved 203 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix A—Power Meter Register List 6/2006 © 2006 Schneider Electric All Rights Reserved 204 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix B—Using the Command Interface APPENDIX B—USING THE COMMAND INTERFACE Overview of the Command Interface The power meter provides a command interface, which you can use to issue commands that perform various operations such as controlling relays. Table B–2 on page 207 lists the available commands. The command interface is located in memory at registers 8000–8149. Table B–1 lists the definitions for the registers. Table B–1: Location of the command interface Register Description 8000 This is the register where you write the commands. These are the registers where you write the parameters for a 8001–8015 command. Commands can have up to 15 parameters associated with them. Command pointer. This register holds the register number where the 8017 last command is stored. Results pointer. This register holds the register number where the last 8018 command is stored. I/O data pointer. Use this register to point to data buffer registers 8019 where you can send additional data or return data. These registers are for you (the user) to write information. Depending on which pointer places the information in the register, the register can contain status (from pointer 8017), results (from pointer 8018), or data (from pointer 8019). The registers will contain information such as 8020–8149 whether the function is enabled or disabled, set to fill and hold, start and stop times, logging intervals, and so forth. By default, return data will start at 8020 unless you specify otherwise. When registers 8017–8019 are set to zero, no values are returned. When any or all of these registers contain a value, the value in the register “points” to a target register, which contains the status, error code, or I/O data (depending on the command) when the command is executed. Figure B–1 shows how these registers work. NOTE: You determine the register location where results will be written. Therefore, take care when assigning register values in the pointer registers; values may be corrupted when two commands use the same register. © 2006 Schneider Electric All Rights Reserved 205 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix B—Using the Command Interface 6/2006 Figure B–1: Command interface pointer registers Register 8017 8020 1 (status of the Register 8020 last command) Register 8018 8021 Register 8021 51 (error code caused by the last command) Register 8019 8022 Register 8022 0 (data returned by the last command) PLSD110152 © 2006 Schneider Electric All Rights Reserved 206 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix B—Using the Command Interface Issuing Commands To issue commands using the command interface, follow these general steps: 1. Write the related parameter(s) to the command parameter registers 8001–15. 2. Write the command code to command interface register 8000. If no parameters are associated with the command, then you need only to write the command code to register 8000. Table B–2 lists the command codes that can be written to the command interface into register 8000. Some commands have an associated registers where you write parameters for that command. For example, when you write the parameter 9999 to register 8001 and issue command code 3351, all relays will be energized if they are set up for external control. Table B–2: Command Codes Command Command Parameter Parameters Description Code Register Causes soft reset of the unit (re-initializes the 1110 None None power meter). 1210 None None Clears the communications counters. Sets the system date and time. Values for the 1310 registers are: 8001 Month Month (1–12) 8002 Day Day (1–31) 8003 Year Year (4-digit, for example 2000) 8004 Hour Hour (Military time, for example 14 = 2:00pm) 8005 Minute Minute (1–59) 8006 Second Second (1–59) Relay Outputs 3310 8001 Relay Output Number ➀ Configures relay for external control. 3311 8001 Relay Output Number ➀ Configures relay for internal control. 3320 8001 Relay Output Number ➀ De-energizes designated relay. 3321 8001 Relay Output Number ➀ Energizes designated relay. Releases specified relay from latched 3330 8001 Relay Output Number ➀ condition. ➀You must write to register 8001 the number that identifies which output you would like to use. To determine the identifying number, refer to“I/O Point Numbers” on page 211 for instructions. ➁Data buffer location (register 8019) is the pointer to the first register where data will be stored. By default, return data begins at register 8020, although you can use any of the registers from 8020–8149. Take care when assigning pointers. Values may be corrupted if two commands are using the same register. © 2006 Schneider Electric All Rights Reserved 207 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix B—Using the Command Interface 6/2006 Table B–2: Command Codes Command Command Parameter Parameters Description Code Register 3340 8001 Relay Output Number ➀ Releases specified relay from override control. 3341 8001 Relay Output Number ➀ Places specified relay under override control. 3350 8001 9999 De-energizes all relays. 3351 8001 9999 Energizes all relays. 3361 8001 Relay Output Number ➀ Resets operation counter for specified relay. 3362 8001 Relay Output Number ➀ Resets the turn-on time for specified relay. 3363 8001 None Resets the operation counter for all relays. 3364 8001 None Resets the turn-on time for all relays. Resets the operation counter for specified 3365 8001 Input Number ➀ input. 3366 8001 Input Number ➀ Resets turn-on time for specified input. 3367 8001 None Resets the operation counter for all inputs. 3368 8001 None Resets turn-on time for all inputs. 3369 8001 None Resets all counters and timers for all I/Os. Resets 1522 None None Resets the alarm history log. 0 = Present and previous months 4110 8001 Resets min/max. 1 = Present month 2 = Previous month 5110 None None Resets all demand registers. 5111 None None Resets current demand. 5113 None None Resets power demand. 5114 None None Resets input demand. Resets generic demand for first group of 10 5115 None None quantities. 5210 None None Resets all min/max demand. 5211 None None Resets current min/max demand. 5213 None None Resets power min/max demand. 5214 None None Resets input min/max demand. 5215 None None Resets generic 1 min/max demand. ➀You must write to register 8001 the number that identifies which output you would like to use. To determine the identifying number, refer to“I/O Point Numbers” on page 211 for instructions. ➁Data buffer location (register 8019) is the pointer to the first register where data will be stored. By default, return data begins at register 8020, although you can use any of the registers from 8020–8149. Take care when assigning pointers. Values may be corrupted if two commands are using the same register. © 2006 Schneider Electric All Rights Reserved 208 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix B—Using the Command Interface Table B–2: Command Codes Command Command Parameter Parameters Description Code Register Start new demand interval. Bit 0 = Power Demand 5910 8001 Bitmap 1 = Current Demand 2 = Input Metering Demand 3 = Generic Demand Profile Preset Accumulated Energies Requires the IO Data Pointer to point to registers where energy preset values are 6209 8019 I/O Data Pointer ➁ entered. All Accumulated energy values must be entered in the order in which they occur in registers 1700 to 1727. 6210 None None Clears all energies. 6211 None None Clears all accumulated energy values. 6212 None None Clears conditional energy values. 6213 None None Clears incremental energy values. 6214 None None Clears input metering accumulation. Resets the following parameters to IEEE or IEC defaults: 1. Phase labels 1 = IEEE 2. Menu labels 6215 None 2 = IEC 3. Harmonic units 4. PF sign 5. THD denominator 6. Date Format 6320 None None Disables conditional energy accumulation. 6321 None None Enables conditional energy accumulation. 6910 None None Starts a new incremental energy interval. Files Triggers data log entry. Bitmap where Bit 0 = 7510 8001 1–3 Data Log 1, Bit 1 = Data Log 2, Bit 2 = Data Log 3, etc. 7511 8001 File Number Triggers single data log entry. ➀You must write to register 8001 the number that identifies which output you would like to use. To determine the identifying number, refer to“I/O Point Numbers” on page 211 for instructions. ➁Data buffer location (register 8019) is the pointer to the first register where data will be stored. By default, return data begins at register 8020, although you can use any of the registers from 8020–8149. Take care when assigning pointers. Values may be corrupted if two commands are using the same register. © 2006 Schneider Electric All Rights Reserved 209 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix B—Using the Command Interface 6/2006 Table B–2: Command Codes Command Command Parameter Parameters Description Code Register Setup 9020 None None Enter into setup mode. 1 = Save 9021 8001 Exit setup mode and save all changes. 2 = Do not save ➀You must write to register 8001 the number that identifies which output you would like to use. To determine the identifying number, refer to“I/O Point Numbers” on page 211 for instructions. ➁Data buffer location (register 8019) is the pointer to the first register where data will be stored. By default, return data begins at register 8020, although you can use any of the registers from 8020–8149. Take care when assigning pointers. Values may be corrupted if two commands are using the same register. © 2006 Schneider Electric All Rights Reserved 210 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix B—Using the Command Interface I/O Point Numbers All inputs and outputs of the power meter have a reference number and a label that correspond to the position of that particular input or output. The reference number is used to manually control the input or output with the command interface. The label is the default identifier that identifies that same input or output. The label appears on the display, in SMS, and on the option card. See Table B–3 on page 211 for a complete list of I/O Point Numbers Table B–3: I/O Point Numbers Module Standard I/O PM8M22 PM8M26 PM8M2222 I/O Point Number KY 1 — —— — S1 2 A-R1 A-R1 3 A-R2 A-R2 4 A-R1 A-S1 A-S1 5 A-R2 A-S2 A-S2 6 A— A-51 A-S3 A-AI1 7 A-52 A-S4 A-AI2 8 A-S5 A-AO1 9 A-S6 A-AO2 10 B-R1 B-R1 11 B-R2 B-R2 12 B-R1 B-S1 B-S1 13 B-R2 B-S2 B-S2 14 B— B-S1 B-S3 B-AI1 15 B-S2 B-S4 B-AI2 16 B-S5 B-AO1 17 B-S6 B-AO2 18 © 2006 Schneider Electric All Rights Reserved 211 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix B—Using the Command Interface 6/2006 Operating Outputs from the Command Interface To operate an output from the command interface, first identify the relay using the I/O point number. Then, set the output to external control. For example, to energize output 1, write the commands as follows: 1. Write number 1 to register 8001. 2. Write command code 3310 to register 8000 to set the relay to external control. 3. Write command code 3321 to register 8000. If you look in the “Relay Outputs” section of Table B–2 on page 207, you’ll see that command code 3310 sets the relay to external control and command code 3321 is listed as the command used to energize a relay. Command codes 3310–3381 are for use with inputs and outputs. © 2006 Schneider Electric All Rights Reserved 212 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix B—Using the Command Interface Using the Command Interface to Change Configuration Registers You can also use the command interface to change values in selected metering-related registers, such as setting the time of day of the clock or resetting generic demand. Two commands, 9020 and 9021, work together as part of the command interface procedure when you use it to change power meter configuration. You must first issue command 9020 to enter into setup mode, change the register, and then issue 9021 to save your changes and exit setup mode. Only one setup session is allowed at a time. While in this mode, if the power meter detects more than two minutes of inactivity, that is, if you do not write any register values or press any buttons on the display, the power meter will timeout and restore the original configuration values. All changes will be lost. Also, if the power meter loses power or communications while in setup mode, your changes will be lost. The general procedure for changing configuration registers using the command interface is as follows: 1. Issue command 9020 in register 8000 to enter into the setup mode. 2. Make changes to the appropriate register by writing the new value to that register. Perform register writes to all registers that you want to change. For instructions on reading and writing registers, see “View the Meter Information” on page 35 in Chapter 3— Operation. 3. To save the changes, write the value 1 to register 8001. NOTE: Writing any other value except 1 to register 8001 lets you exit setup mode without saving your changes. 4. Issue command 9021 in register 8000 to initiate the save and reset the power meter. For example, the procedure to change the demand interval for current is as follows: 1. Issue command code 9020 in register 8000. 2. Write the new demand interval to register 1801. 3. Write 1 to register 8001. 4. Issue command code 9021 in register 8000. See Appendix A—Power Meter Register List on page 121 for those registers that require you to enter setup mode to make changes to the registers. © 2006 Schneider Electric All Rights Reserved 213 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix B—Using the Command Interface 6/2006 Conditional Energy Power meter registers 1728–1744 are conditional energy registers. Conditional energy can be controlled in one of two ways: Over the communications link, by writing commands to the power meter’s command interface, or By a digital input—for example, conditional energy accumulates when the assigned digital input is on, but does not accumulate when the digital input is off. The following procedures tell how to set up conditional energy for command interface control, and for digital input control. The procedures refer to register numbers and command codes. For a listing of power meter registers, see Appendix A—Register List on page 124. For a listing of command codes, see Table B–2 on page 207 in this chapter. Command Interface Control Set Control—To set control of conditional energy to the command interface: 1. Write command code 9020 to register 8000. 2. In register 3227, set bit 6 to 1 (preserve other bits that are ON). 3. Write 1 to register 8001. 4. Write command code 9021 to register 8000. Start— To start conditional energy accumulation, write command code 6321 to register 8000. Verify Setup—To verify proper setup, read register 1794. The register should read 1, indicating conditional energy accumulation is ON. Stop—To stop conditional energy accumulation, write command code 6320 to register 8000. Clear—To clear all conditional energy registers (1728-1747), write command code 6212 to register 8000. © 2006 Schneider Electric All Rights Reserved 214 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix B—Using the Command Interface Digital Input Control Set Control—To configure conditional energy for digital input control: 1. Write command code 9020 to register 8000. 2. In register 3227, set bit 6 to 0 (preserve other bits that are ON). 3. Configure the digital input that will drive conditional energy accumulation. For the appropriate digital input, write 3 to the Base +9 register. See the digital input templates in Table A–3 on page 124 in Appendix A—Power Meter Register List on page 121. 4. Write 1 to register 8001. 5. Write command code 9021 to register 8000. Clear—To clear all conditional energy registers (1728–1747), write command code 6212 to register 8000. Verify Setup—To verify proper setup, read register 1794. The register should read 0 when the digital input is off, indicating that conditional energy accumulation is off. The register should read 1 when conditional energy accumulation is on. Incremental Energy The power meter’s incremental energy feature allows you to define a start time, end time, and time interval for incremental energy accumulation. At the end of each incremental energy period, the following information is available: Wh IN during the last completed interval (reg. 1748–1750) VARh IN during the last completed interval (reg. 1751–1753) Wh OUT during the last completed interval (reg. 1754–1756) VARh OUT during the last completed interval (reg. 1757–1759) VAh during the last completed interval (reg. 1760–1762) Date/time of the last completed interval (reg. 1763–1765) Peak kW demand during the last completed interval (reg. 1940) Date/Time of Peak kW during the last interval (reg. 1941–1943) Peak kVAR demand during the last completed interval (reg. 1945) Date/Time of Peak kVAR during the last interval (reg. 1946–1948) Peak kVA demand during the last completed interval (reg. 1950) Date/Time of Peak kVA during the last interval (reg. 1951–1953) © 2006 Schneider Electric All Rights Reserved 215 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix B—Using the Command Interface 6/2006 The power meter can log the incremental energy data listed above. This logged data provides all the information needed to analyze energy and power usage against present or future utility rates. The information is especially useful for comparing different time-of-use rate structures. When using the incremental energy feature, keep the following points in mind: Peak demands help minimize the size of the data log in cases of sliding or rolling demand. Shorter incremental energy periods make it easier to reconstruct a load profile analysis. Since the incremental energy registers are synchronized to the power meter clock, it is possible to log this data from multiple circuits and perform accurate totalizing. Using Incremental Energy Incremental energy accumulation begins at the specified start time and ends at the specified end time. When the start time arrives, a new incremental energy period begins. The start and end time are specified in minutes from midnight. For example: Interval: 420 minutes (7 hours) Start time: 480 minutes (8:00 a.m.) End time = 1440 minutes (12:00 p.m.) The first incremental energy calculation will be from 8:00 a.m. to 3:00 p.m. (7 hours) as illustrated in Figure B–2 on page 217. The next interval will be from 3:00 p.m. to 10:00 p.m., and the third interval will be from 10 p.m. to 12:00 p.m. because 12:00 p.m. is the specified end time. A new interval will begin on the next day at 8:00 a.m. Incremental energy accumulation will continue in this manner until the configuration is changed or a new interval is started by a remote master. © 2006 Schneider Electric All Rights Reserved 216 2 n d I n t e ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix B—Using the Command Interface Figure B–2: Incremental energy example End Time 12 11 1 10 2 9 3 8 4 Start Time 7 5 6 1st Interval (7 hours) = 8:00 a.m. to 3:00 p.m 2nd Interval (7 hours) = 3:00 p.m. to 10:00 p.m 3rd Interval (2 hours) = 10:00 p.m. to 12:00 p.m Set up—To set up incremental energy: 1. Write command code 9020 to register 8000. 2. In register 3230, write a start time (in minutes-from-midnight). 3. For example, 8:00 am is 480 minutes. 4. In register 3231, write an end time (in minutes-from-midnight). 5. Write the desired interval length, from 0–1440 minutes, to register 3229. 6. If incremental energy will be controlled from a remote master, such as a programmable controller, write 0 to the register. 7. Write 1 to register 8001. 8. Write command code 9021 to register 8000. Start—To start a new incremental energy interval from a remote master, write command code 6910 to register 8000. © 2006 Schneider Electric All Rights Reserved 217 r l v a a v l r e l a t n v I r e t t s n 1 I d r 3 PLSD110149 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix B—Using the Command Interface 6/2006 Setting Up Individual Harmonic Calculations The Power Meter can perform harmonic magnitude and angle calculations for each metered value and for each residual value. The harmonic magnitude for current and voltage can be formatted as either a percentage of the fundamental (THD), as a percentage of the rms values (thd), or rms. The harmonic magnitude and angles are stored in a set of registers: 13,200–14,608. During the time that the power meter is refreshing harmonic data, the power meter posts a value of 0 in register 3246. When the set of harmonic registers is updated with new data, the power meter posts a value of 1 in register 3246. The power meter can be configured to hold the values in these registers for up to 60 metering update cycles once the data processing is complete. The power meter has three operating modes for harmonic data processing: disabled, magnitude only, and magnitude and angles. Because of the extra processing time necessary to perform these calculations, the factory default operating mode is magnitudes only. To configure the harmonic data processing, write to the registers described in Table B–4: Table B–4: Registers for Harmonic Calculations Reg No. Value Description Harmonic processing; 0 = disabled 3240 0, 1, 2 1 = magnitudes only enabled 2 = magnitudes and angles enabled Harmonic magnitude formatting for voltage; 0 = % of fundamental (default) 3241 0, 1, 2 1 = % of rms 2 = rms Harmonic magnitude formatting for current; 0 = % of fundamental (default) 3242 0, 1, 2 1 = % of rms 2 = rms This register shows the harmonics refresh interval 3243 10–60 seconds (default is 30 seconds). © 2006 Schneider Electric All Rights Reserved 218 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix B—Using the Command Interface Table B–4: Registers for Harmonic Calculations Reg No. Value Description This register shows the time remaining before the 3244 0–60 seconds next harmonic data update. This register indicates whether harmonic data processing is complete: 3245 0,1 0 = processing incomplete 1 = processing complete Changing Scale Factors The power meter stores instantaneous metering data in 16-bit single registers. A value held in each register must be an integer between – 32,767 and +32,767. Because some values for metered current, voltage, and power readings fall outside this range, the power meter uses multipliers, or scale factors. This enables the power meter to extend the range of metered values that it can record. The power meter stores these multipliers as scale factors. A scale factor is the multiplier expressed as a power of 10. For example, a 1 multiplier of 10 is represented as a scale factor of 1, since 10 =10; a 2 multiplier of 100 is represented as a scale factor of 2, since 10 =100. You can change the default value of 1 to other values such as 10, 100, or 1,000. However, these scale factors are automatically selected when you set up the power meter, either from the display or by using SMS. If the power meter displays “overflow” for any reading, change the scale factor to bring the reading back into a range that fits in the register. For example, because the register cannot store a number as large as 138,000, a 138 kV system requires a multiplier of 10. 138,000 is converted to 13,800 x 10. The power meter stores this 1 value as 13,800 with a scale factor of 1 (because 10 =10). Scale factors are arranged in scale groups. The abbreviated register list in Appendix A—Power Meter Register List on page 121 shows the scale group associated with each metered value. © 2006 Schneider Electric All Rights Reserved 219 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix B—Using the Command Interface 6/2006 You can use the command interface to change scale factors on a group of metered values. However, be aware of these important points if you choose to change scale factors: NOTE: We strongly recommend that you do not change the default scale factors, which are automatically selected by POWERLOGIC hardware and software. When using custom software to read power meter data over the communications link, you must account for these scale factors. To correctly read any metered value with a scale factor other than 0, multiply the register value read by the appropriate power of 10. As with any change to basic meter setup, when you change a scale factor, all min/max and peak demand values should be reset. Enabling Floating-point Registers For each register in integer format, the power meter includes a duplicate set of registers in floating-point format. For an abbreviated list of floating-point registers, see Table A–7 on page 183. The floating point registers are disabled by default, but they can be turned ON by doing the following: NOTE: See “Read and Write Registers” on page 36 for instructions on how to read and write registers. 1. Read register 11700 (Current Phase A in floating-point format). If floating-point registers are OFF, you will see -32,768. 2. Write command code 9020 to register 8000. 3. Write 1 in register 3248. 4. Write 1 to register 8001. 5. Write command code 9021 to register 8000. 6. Read register 11700. You will see a value other than -32,768, which indicates floating-point registers are ON. NOTE: Values such as current phase A are not shown in floating-point format on the display even though floating-point registers are ON. To view floating-point values, read the floating-point registers using the display or SMS. © 2006 Schneider Electric All Rights Reserved 220 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix C—EN50160 Evaluation APPENDIX C—EN50160 EVALUATION This section applies to the following models: PM850 PM870 This section also describes how the PM850 and the PM870 operate when the European standard EN50160 evaluation feature is enabled. For instructions on how to enable the evaluation feature, see “Setting Up EN50160 Evaluation from the Display” on page 241. Overview EN50160:2000 “Voltage characteristics of electricity supplied by public distribution systems” is a European standard that defines the quality of the voltage a customer can expect from the electric utility. Although this is a European standard, it can be applied in the U.S. The PM850 and the PM870 evaluates the following electrical characteristics in accordance with EN50160: Table C–1: EN50160 Evaluation for the PM850 and the PM870 Feature PM850 PM870 Evaluation During Normal Operation (Meter-based Data) Frequency ✓✓ Supply voltage variations ✓✓ Supply voltage unbalance ✓✓ Harmonic voltage ✓✓ Total Harmonic Distortion ✓✓ ➀ Evaluations During Abnormal Operations (Alarm-based Data) Magnitude of rapid voltage changes ✓✓ ➁ ➁ Supply voltage dips ✓ ✓ ➁ ➁ Short interruptions of the supply voltage ✓ ✓ ➁ ➁ Long interruptions of the supply voltage ✓ ✓ ➁ ➁ Temporary power frequency overvoltages ✓ ✓ ➀ The PM850 performs EN50160 evaluations based on standard alarms, while the PM870 performs EN50160 evaluations on disturbance alarms. ➁ Must be configured using register writes. See Table C–4 on page 231 for a list of configuration registers. © 2006 Schneider Electric All Rights Reserved 221 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix C—EN50160 Evaluation 6/2006 As illustrated in Table C–1 above, the EN50160 evaluations performed by the PM850 and the PM870 can be divided into two categories. The first category performs evaluations during normal operation utilizing meter data. The second category performs evaluations during abnormal operation utilizing either standard alarms (PM850) or disturbance alarms (PM870). The standard sets limits for most of the evaluations. These limits are built into the PM850 and the PM870 firmware. You can configure registers for other evaluations and change them from the default values. © 2006 Schneider Electric All Rights Reserved 222 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix C—EN50160 Evaluation How Results of the Evaluations Are Reported The PM850 and the PM870 reports evaluation data in register entries and alarm log entries. Table C–2 describes the register entries for the evaluation data. Table C–2: Register Entries Register Description Number Summary bitmap of active evaluations that reports which 3910 areas of evaluation are active in the PM850 and the PM870. Summary bitmap of evaluation status that reports the 3911 pass/fail status of each area of evaluation. Detail bitmap of evaluation status that reports the pass/fail status of the evaluation of each individual data item. Detailed data summary information is also available for each of the evaluations for the present interval and for the Portal registers previous interval. You can access this data over a communications link using Modbus block reads of “portal” registers. Refer to “Evaluation During Normal Operation” on page 224 for additional information. Log entries for the evaluation data include: Onboard alarm log entry for diagnostic alarms: When the status of an area of evaluation is outside the range of acceptable values, an entry is made in the on-board alarm log. This entry provides notification of the exception for a specific area of evaluation. This notification is reported only in SMS and does not appear on the local display. Onboard alarm log entry for alarms: PM850 and the PM870 alarms are used to perform some of the evaluations. If an onboard alarm log is enabled, an entry will be made in the on-board alarm log when any of these alarms pick up or drop out. NOTE: Enabling EN50160 evaluation does not guarantee that the onboard alarm log is enabled or properly configured to record these events. Also, when you enable EN50160 evaluation, you do not automatically configure onboard data logging or waveform capture files. You should consider your requirements and configure these files and the event captures triggered by the various alarms to provide any additional data that would be helpful to diagnose or document an exception to this standard. © 2006 Schneider Electric All Rights Reserved 223 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix C—EN50160 Evaluation 6/2006 Possible Configurations Through Register Writes This section describes the changes you can make to configurations for the EN50160 evaluation through register writes in the PM850 and the PM870. Refer to “EN50160 Evaluation System Configuration and Status Registers” on page 231 for register assignments. Select the first day of the week for evaluations. You can define the first day of the week to be used for the EN50160 evaluations in register 3905. Define the voltage interruption. The standard defines an interruption as voltage less than 1% of nominal voltage. Because some locations require a different definition, you can configure this value in register 3906. Define allowable range of slow voltage variations. The standard defines the allowable range of slow voltage variations to be ±10% of nominal voltage. Because some locations require a different definition, you can configure this value in register 3907. 1 Evaluation During Normal Operation When the EN50160 evaluation is enabled, the PM850 and the PM870 evaluates metered data under normal operating conditions, “excluding situations arising from faults or voltage interruptions.” For this evaluation, normal operating conditions are defined as all phase voltages greater than the definition of interruption. The standard specifies acceptable ranges of operation for these data items. This section describes how the EN50160 standard addresses metered data. Power Frequency EN50160 states that the nominal frequency of the supply voltage shall be 50 Hz. Under normal operating conditions the mean value of the fundamental frequency measured over ten seconds shall be within the following range: for systems with synchronous connection to an interconnected system: — 50 Hz ± 1% during 99.5% of a year — 50 Hz + 4 to -6% for 100% of the time 1 BS EN 50160:2000, Voltage characteristics of electricity supplied by public distribution systems, BSi. © 2006 Schneider Electric All Rights Reserved 224 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix C—EN50160 Evaluation for systems with no synchronous connection to an interconnected system (for example, power systems on some islands): —50 Hz ± 2% during 95% of a week —50 Hz ± 15% for 100% of the time NOTE: The same range of percentages are used for 60 Hz systems. Supply Voltage Variations EN50160 states that under normal operating conditions, excluding situations arising from faults or voltage interruptions during each period of one week 95% of the ten minute mean rms values of the supply voltage shall be within the range of U ±10%. n all ten minute mean rms values of the supply voltage shall be within the range of U +10% to -15%. n Supply Voltage Unbalance EN50160 states that under normal operating conditions, during each period of one week, 95% of the ten minute mean rms values of the negative phase sequence component of the supply voltage shall be within the range 0–2% of the positive phase sequence component. Harmonic Voltage EN50160 states that under normal operating conditions, during each period of one week, 95% of the ten minute mean rms values of each individual harmonic voltage shall be less than or equal to the value given in Table C–3. Additionally, the THD of the supply voltage shall be less than 8%. © 2006 Schneider Electric All Rights Reserved 225 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix C—EN50160 Evaluation 6/2006 Table C–3: Values of individual harmonic voltages at the supply terminals for orders up to 25 in % of nominal voltage Odd Harmonics Even Harmonics Not Multiples of 3 Multiples of 3 Relative Relative Relative Order h Order h Order h Voltage Voltage Voltage 56% 3 5% 22% 75% 9 1.5% 41% 11 3.5% 15 0.5% 6...24 0.5% 13 3% 21 0.5% 17 2% 19 1.5% 23 1.5% 25 NOTE: No values are given for harmonics of order higher than 25, as they are usually small, but largely unpredictable because of resonance effects. © 2006 Schneider Electric All Rights Reserved 226 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix C—EN50160 Evaluation Evaluations During Abnormal Operation Count of Magnitude of Rapid Voltage Changes The standard does not specify the rate of change of the voltage for this evaluation. For this evaluation, the PM850 and the PM870 counts a change of ≥ 5% nominal and ≤10% nominal from one one-second meter cycle to the next one-second meter cycle. It counts rapid voltage decreases and increases separately. The interval for accumulation of these events is one week. You can configure the number of allowable events per week in register 3917. (Default = -32768 = Pass/Fail evaluation disabled.) Detection and Classification of Supply Voltage Dips According to EN50160, voltage dips are generally caused by faults in installations or the electrical utility distribution system. The faults are unpredictable and frequency varies depending on the type of power system and where events are monitored. Under normal operating conditions, the number of voltage dips expected may be anywhere from less than a hundred to nearly a thousand. The majority of voltage dips last less than one second with a depth less than 60%. However, voltage dips of greater depth and duration can occasionally occur. In some regions, voltage dips with depths between 10% and 15% of the nominal voltage are common because of the switching of loads at a customer’s installation. Supply voltage dips are under-voltage events that last from 10 ms to 1 minute. Magnitudes are the minimum rms values during the event. Disturbance alarms are used to detect these events in the PM870. Standard speed undervoltage alarms are used to detect these events in the PM850. The standard does not specifically address how to classify supply voltage dips or how many are allowable. The PM850 and the PM870 detects and classifies the dips for each phase voltage as follows: © 2006 Schneider Electric All Rights Reserved 227 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix C—EN50160 Evaluation 6/2006 Duration (t) seconds Depth (D) % Nominal 1 ≤ t < 3 3 ≤ t < 10 10 ≤ t < 20 20 ≤ t < 60 60 ≤ t < 180 Total 10 ≤ D < 15 15 ≤ D < 30 30 ≤ D < 45 45 ≤ D < 60 60 ≤ D < 75 75 ≤ D < 90 90 ≤ D < 99 Total You can configure the number of allowable events per week for each range of Depth in registers 3920 – 3927. (Default = -32768 = Pass/Fail evaluation disabled.) Detection of Interruptions of the Supply Voltage The standard defines an interruption as voltage less than 1% of nominal voltage. Because some locations require a different definition, you can configure this value in register 3906. Interruptions are classified as “short” if duration ≤ 3 minutes or “long” otherwise. The PM850 and the PM870 classifies interruptions as shown in the following table. Duration (t) seconds 5 ≤ t < 10 ≤ t < 20 ≤ t < 60 ≤t < 180 ≤t < 600 ≤t < t < 1 1 ≤ t < 2 2 ≤ t < 5 1200 ≤ t 10 20 60 180 600 1200 Total You can configure the number of allowable short interruptions per year in register 3918 (Default = -32768 = Pass/Fail evaluation disabled). You can configure the number of allowable long interruptions per year in register 3919. (Default = -32768 = Pass/Fail evaluation disabled.) Detecting and Classifying Temporary Power Frequency Overvoltages As stated in EN50160, a temporary power frequency overvoltage generally appears during a fault in the electrical utility power distribution system or in a customer’s installation, and disappears when the fault is cleared. Usually, the overvoltage may reach the © 2006 Schneider Electric All Rights Reserved 228 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix C—EN50160 Evaluation value of phase-to-phase voltage because of a shift of the neutral point of the three-phase voltage system. Under certain circumstances, a fault occurring upstream from a transformer will produce temporary overvoltages on the low voltage side for the time during which the fault current flows. Such overvoltages will generally not exceed 1.5 kV rms. The PM850 and the PM870 detects and classifies the overvoltages for each phase voltage as follows: NOTE: Disturbance alarms are used to detect these events in the PM870. In the PM850, standard speed overvoltage alarms are used to detect these events. Duration (t) seconds Magnitude (M) % 1 ≤ t < 3 3 ≤ t < 10 10 ≤ t < 20 20 ≤ t < 60 60 ≤ t < 180 Total Nominal 110 < M ≤ 115 115 < M ≤ 130 130 < M ≤ 145 145 < M ≤ 160 160 < M ≤ 175 175 < M ≤ 200 M > 200 Total You can configure the number of allowable events per week for each range of Magnitude in registers 3930 – 3937. (Default = -32768 = Pass/Fail evaluation disabled.) © 2006 Schneider Electric All Rights Reserved 229 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix C—EN50160 Evaluation 6/2006 Operation with EN50160 Enabled This section describes how PM850 and the PM870 operation is affected when EN50160 evaluation is enabled. Resetting Statistics You can reset statistics for the EN50160 evaluations with the command 11100. A parameter value of 9999 will reset all items. A timestamp is provided in registers for each item indicating when the last reset was performed. This command is disabled when revenue security is active. NOTE: You should reset statistics when you enable EN50160 for the first time and also whenever you make any changes to the basic meter setup such as changing the nominal voltage. See “Setting Up EN50160 Evaluation from the Display” on page 241. Alarms Allocated for Evaluations To accomplish some of the evaluations required and to provide a record of events in the on-board alarm log, the PM850 uses standard alarms, and the PM870 uses disturbance alarms. When the evaluation is enabled, certain alarm positions will be claimed for use in the evaluation. You cannot use these alarms for other purposes while the evaluation is enabled. These alarms include: Over Voltage (PM850): Standard speed alarm positions 35-37 Under Voltage (PM850): Standard speed alarm positions 38-40 Disturbance for Voltage Swells and Sags (PM870): Disturbance alarm positions 1-3 and 7-9 NOTE: The position depends on the system type (register 3902). “EN50160” is included in the alarm label for alarms being used by this evaluation. Harmonic Calculations When EN50160 evaluation is enabled, the harmonic calculations will be set to update every 10 seconds. You can select the format of the harmonic calculations to be %Nominal, %Fundamental, or %RMS. Time Intervals Time intervals are synchronized with the Trending and Forecasting feature. Refer to the POWERLOGIC Web Pages instruction bulletin 63230-304-207. Weekly values will be posted at midnight of the © 2006 Schneider Electric All Rights Reserved 230 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix C—EN50160 Evaluation morning of the “First Day of Week” configured in register 3905. Yearly values will be based on the calendar year. All of the EN50160 data is stored in non-volatile memory once per hour or when an event occurs. In the event of a meter reset, up to one hour of routine meter evaluation data will be lost. EN50160 Evaluation System Configuration and Status Registers Table C–4 lists registers for system configuration and status evaluation. Table C–4: EN50160 Evaluation System Configuration and Status Registers Register Number Description 3900 1 Enable/Disable EN50160 Evaluation 0 = Disable (default) 1 = Enable 3901 1 Nominal Voltage, (copied from register 3234 for reference) Default = 230 3902 1 Voltage Selection for 4-Wire Systems 0 = Line-to-Neutral (default) 1 = Line-to-Line 3903 1 Nominal Frequency, Hz (copied from register 3208 for reference) Default = 60 3904 1 Frequency configuration 0 = system with synchronous connection to interconnected system (default) 1 = system without synchronous connection to interconnected system 3905 1 First Day of Week 1 = Sunday 2 = Monday (default) 3 = Tuesday 4 = Wednesday 5 = Thursday 6 = Friday 7 = Saturday 3906 1 Definition of Interruption 0 – 10% Nominal (default = 1) 3907 1 Allowable Range of Slow Voltage Variations 1 – 20% Nominal (default = 10) 3908 1 Reserved 3909 1 Reserved © 2006 Schneider Electric All Rights Reserved 231 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix C—EN50160 Evaluation 6/2006 Table C–4: EN50160 Evaluation System Configuration and Status Registers 3910 1 Bitmap of active evaluations Bit 00 – Summary bit – at least one EN50160 evaluation is active Bit 01 – Frequency Bit 02 – Supply voltage variations Bit 03 – Magnitude of rapid voltage changes Bit 04 – Not used Bit 05 – Supply voltage dips Bit 06 – Short interruptions of the supply voltage Bit 07 – Long interruptions of the supply voltage Bit 08 – Temporary power frequency overvoltages Bit 09 – Not used Bit 10 – Supply voltage unbalance Bit 11 – Harmonic voltage Bit 12 – THD Bit 13 – Not used Bit 14 – Not used Bit 15 – Not used 3911 1 Bitmap of evaluation status summary Bit 00 – Summary bit – at least one EN50160 evaluation has failed. Bit 01 – Frequency Bit 02 – Supply voltage variations Bit 03 – Magnitude of rapid voltage changes Bit 04 – Not used Bit 05 – Supply voltage dips Bit 06 – Short interruptions of the supply voltage Bit 07 – Long interruptions of the supply voltage Bit 08 – Temporary power frequency overvoltages Bit 09 – Not used Bit 10 – Supply voltage unbalance Bit 11 – Harmonic voltage Bit 12 – THD Bit 13 – Not used Bit 14 – Not used Bit 15 – Not used 3912 2 Count of 10-second intervals present year 3914 2 Count of 10-second intervals this week 3916 1 Count of 10-minute intervals this week 3917 1 Number of allowable rapid voltage changes per week Default = -32768 = Pass/Fail evaluation disabled 3918 1 Number of allowable short interruptions per year Default = -32768 = Pass/Fail evaluation disabled 3919 1 Number of allowable long interruptions per year Default = -32768 = Pass/Fail evaluation disabled 3920 8 Number of allowable voltage dips per week for each range of Depth Default = -32768 = Pass/Fail evaluation disabled 3930 8 Number of allowable overvoltages per week for each range of Magnitude Default = -32768 = Pass/Fail evaluation disabled © 2006 Schneider Electric All Rights Reserved 232 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix C—EN50160 Evaluation Evaluation Data Available Over a Communications Link Portal Registers Evaluation data is available over communications via “portal” register reads. Each data item is assigned a portal register number. A block read of the specified size at that address will return the data for that item. In general, if the block size is smaller than specified, the data returned will be 0x8000 (-32768) to indicate the data is invalid. If the block size is larger than specified, the data for the item will be returned and the remaining registers will be padded with 0x8000. Refer to Table C–5 for portal register descriptions. © 2006 Schneider Electric All Rights Reserved 233 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix C—EN50160 Evaluation 6/2006 Table C–5: Portal Register Descriptions Portal Description Size Data Register number of Metered Quantity (can be used to confirm data item being reported) Register value (present metered value) Average value (at end of last completed averaging time period) Minimum value during the last completed averaging time period Maximum value during the last completed averaging time period Minimum value during this interval Maximum value during this interval Minimum value during the last interval Maximum value during the last interval Summary of Percent in Evaluation Range 1 this interval 53432 – Meter Data 33 Percent in Evaluation Range 2 this interval (when applicable) 53434 Evaluations by Item Percent in Evaluation Range 1 last interval Percent in Evaluation Range 2 last interval (when applicable) Count of average values in Evaluation Range 1 (MOD10L2) Count of average values in Evaluation Range 2 (MOD10L2) Count of total valid averages for Evaluation of Range 1 (MOD10L2) Count of total valid averages for Evaluation of Range 2 (MOD10L2) Date/Time Last Excursion Range 1 (4-register format) Date/Time Last Excursion Range 2 (4-register format) Date/Time Last Reset (4-register format) Count of rapid voltage increases this week Count of rapid voltage decreases this week Summary of Rapid Count of rapid voltage increases last week 53435 – Voltage 12 53437 Count of rapid voltage decreases last week Changes by Phase Date/Time last rapid voltage change (4-register format) Date/Time last reset (4-register format) Count of dips by magnitude & duration this week (96 values) [See Summary of “Detection and Classification of Supply Voltage Dips” on page 53438 – Voltage Dips 227.] 104 53440 by Phase Date/Time last voltage dip (4-register format) This Week Date/Time last reset (4-register format) © 2006 Schneider Electric All Rights Reserved 234 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix C—EN50160 Evaluation Table C–5: Portal Register Descriptions Portal Description Size Data Count of dips by magnitude & duration last week (96 values) [See Summary of “Detection and Classification of Supply Voltage Dips” on page 53441 – Voltage Dips 227. 104 53443 by Phase Date/Time last voltage dip (4-register format) Last Week Date/Time last reset (4-register format) Flag indicating interruption is active Elapsed seconds for interruption in progress Count of short interruptions this year Count of long interruption this year Summary of Count of short interruptions last year Supply 53444 – Voltage Count of long interruptions last year 34 53447 Interruptions Count of interruptions by duration this year (10 values) [See 3-Phase and “Detection of Interruptions of the Supply Voltage” on page 228.] by Phase Count of interruptions by duration last year (10 values) [See “Detection of Interruptions of the Supply Voltage” on page 228.] Date/Time of last interruption (4-register format) Date/Time of last reset (4-register format) Temporary Count of overvoltages by magnitude & duration this week (96 Power values) [See “Detecting and Classifying Temporary Power 53448 – Frequency Frequency Overvoltages” on page 228.] 104 53449 Overvoltage Date/Time last overvoltage (4-register format) s by Phase This Week Date/Time last reset (4-register format) Temporary Count of overvoltages by magnitude & duration last week (96 Power values) [See “Detecting and Classifying Temporary Power 53450 – Frequency Frequency Overvoltages” on page 228.] 104 53452 Overvoltage Date/Time last overvoltage (4-register format) s by Phase Last Week Date/Time last reset (4-register format) © 2006 Schneider Electric All Rights Reserved 235 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix C—EN50160 Evaluation 6/2006 Table C–5: Portal Register Descriptions Portal Description Size Data Register 1 – Bitmap of active Register 2 – Bitmap of evaluations (same as register evaluation status summary 3910) (same as register 3911) Bit set when evaluation is active Bit set when evaluation fails Bit 00 – Summary bit – at least Bit 00 – Summary bit – at least one EN50160 evaluation is one EN50160 evaluation has active failed Bit 01 – Frequency Bit 01 – Frequency Bit 02 – Supply voltage Bit 02 – Supply voltage variations variations Bit 03 – Magnitude of rapid Bit 03 – Magnitude of rapid voltage changes voltage changes Bit 04 – Not used Bit 04 – Not used Bit 05 – Supply voltage dips Bit 05 – Supply voltage dips Evaluation 53312 Summary 18 Bit 06 – Short interruptions of Bit 06 – Short interruptions of Bitmap the supply voltage the supply voltage Bit 07 – Long interruptions of Bit 07 – Long interruptions of the supply voltage the supply voltage Bit 08 – Temporary power Bit 08 – Temporary power frequency overvoltages frequency overvoltages Bit 09 – Not used Bit 09 – Not used Bit 10 – Supply voltage Bit 10 – Supply voltage unbalance unbalance Bit 11 – Harmonic voltage Bit 11 – Harmonic voltage Bit 12 – THD Bit 12 – THD Bit 13 – Not used Bit 13 – Not used Bit 14 – Not used Bit 14 – Not used Bit 15 – Not used Bit 15 – Not used © 2006 Schneider Electric All Rights Reserved 236 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix C—EN50160 Evaluation Table C–5: Portal Register Descriptions Portal Description Size Data Register 3 (Range 1)/Register Register 4 (Range 1)/Register 11 (Range 2) – Bitmap of 12 (Range 2) – Bitmap of evaluation status of individual evaluation status of individual evaluations evaluations Bit 00 – Frequency Bit 00 – Va H7 Bit 01 – Va Bit 01 – Va H8 Bit 02 – Vb Bit 02 – Va H9 Bit 03 – Vc Bit 03 – Va H10 Bit 04 – Not used Bit 04 – Va H11 Bit 05 – Not used Bit 05 – Va H12 Bit 06 – Not used Bit 06 – Va H13 Bit 07 – Voltage Unbalance Bit 07 – Va H14 Bit 08 – THD Va Bit 08 – Va H15 Bit 09 – THD Vb Bit 09 – Va H16 Bit 10 – THD Vc Bit 10 – Va H17 Bit 11 – Va H2 Bit 11 – Va H18 Bit 12 – Va H3 Bit 12 – Va H19 Bit 13 – Va H4 Bit 13 – Va H20 Bit 14 – Va H5 Bit 14 – Va H21 Bit 15 – Va H6 Bit 15 – Va H22 © 2006 Schneider Electric All Rights Reserved 237 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix C—EN50160 Evaluation 6/2006 Table C–5: Portal Register Descriptions Portal Description Size Data Register 5 (Range 1)/Register Register 6 (Range 1)/Register 13 (Range 2) – Bitmap of 14 (Range 2) – Bitmap of evaluation status of individual evaluation status of individual evaluations evaluations Bit 00 – Va H23 Bit 00 – Vb H15 Bit 01 – Va H24 Bit 01 – Vb H16 Bit 02 – Va H25 Bit 02 – Vb H17 Bit 03 – Vb H2 Bit 03 – Vb H18 Bit 04 – Vb H3 Bit 04 – Vb H19 Bit 05 – Vb H4 Bit 05 – Vb H20 Bit 06 – Vb H5 Bit 06 – Vb H21 Bit 07 – Vb H6 Bit 07 – Vb H22 Bit 08 – Vb H7 Bit 08 – Vb H23 Bit 09 – Vb H8 Bit 09 – Vb H24 Bit 10 – Vb H9 Bit 10 – Vb H25 Bit 11 – Vb H10 Bit 11 – Vc H2 Bit 12 – Vb H11 Bit 12 – Vc H3 Bit 13 – Vb H12 Bit 13 – Vc H4 Bit 14 – Vb H13 Bit 14 – Vc H5 Bit 15 – Vb H14 Bit 15 – Vc H6 © 2006 Schneider Electric All Rights Reserved 238 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix C—EN50160 Evaluation Table C–5: Portal Register Descriptions Portal Description Size Data Register 7 (Range 1)/Register Register 8 (Range 1)/Register 15 (Range 2) – Bitmap of 16 (Range 2) – Bitmap of evaluation status of individual evaluation status of individual evaluations evaluations Bit 00 – Vc H7 Bit 00 – Vc H23 Bit 01 – Vc H8 Bit 01 – Vc H24 Bit 02 – Vc H9 Bit 02 – Vc H25 Bit 03 – Vc H10 Bit 03 – V 3PH Bit 04 – Vc H11 Bit 04 – KW 3PH Bit 05 – Vc H12 Bit 05 – KVAR 3PH Bit 06 – Vc H13 Bit 06 – Ia Bit 07 – Vc H14 Bit 07 – Ib Bit 08 – Vc H15 Bit 08 – Ic Bit 09 – Vc H16 Bit 09 – Ia H3 Bit 10 – Vc H17 Bit 10 – Ib H3 Bit 11 – Vc H18 Bit 11 – Ic H3 Bit 12 – Vc H19 Bit 12 – Ia H5 Bit 13 – Vc H20 Bit 13 – Ib H5 Bit 14 – Vc H21 Bit 14 – Ic H5 Bit 15 – Vc H22 Bit 15 – Ia H7 © 2006 Schneider Electric All Rights Reserved 239 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix C—EN50160 Evaluation 6/2006 Table C–5: Portal Register Descriptions Portal Description Size Data Register 9 (Range 1)/Register Register 10 (Range 1)/Register 17 (Range 2) – Bitmap of 18 (Range 2) – Bitmap of evaluation status of individual evaluation status of individual evaluations evaluations Bit 00 – Ib H7 Bit 00 – Reserved Bit 01 – Ic H7 Bit 01 – Reserved Bit 02 – Ia H9 Bit 02 – Reserved Bit 03 – Ib H9 Bit 03 – Reserved Bit 04 – Ic H9 Bit 04 – Reserved Bit 05 – Ia H11 Bit 05 – Reserved Bit 06 – Ib H11 Bit 06 – Reserved Bit 07 – Ic H11 Bit 07 – Reserved Bit 08 – Ia H13 Bit 08 – Not used Bit 09 – Ib H13 Bit 09 – Not used Bit 10 – Ic H13 Bit 10 – Not used Bit 11 – Reserved Bit 11 – Not used Bit 12 – Reserved Bit 12 – Not used Bit 13 – Reserved Bit 13 – Not used Bit 14 – Reserved Bit 14 – Not used Bit 15 – Reserved Bit 15 – Not used © 2006 Schneider Electric All Rights Reserved 240 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix C—EN50160 Evaluation Setting Up EN50160 Evaluation from the Display To set up the EN50160 evaluation in the power meter, you need to perform these steps: 1. Enable the EN50160 evaluation. By default, the EN50160 evaluation is disabled. To enable the evaluation, use the display (see “Set Up the EN50160 Evaluation” on page 30). 2. Select the nominal voltage of your system. The EN50160 standard defines nominal voltage for low-voltage systems to be 230V line-to-line for 3-wire systems or 230V line-to-neutral for 4-wire systems. Therefore, the default value for Nominal Voltage is 230. If the application is a medium-voltage system or if you want the evaluations to be based on some other nominal voltage, you can configure this value using the display only. SMS does not allow configuration of nominal voltage 3. Change the nominal frequency of your system if you are evaluating a 50 Hz system. The EN50160 standard defines nominal frequency as 50 Hz, but the PM850 and the PM870 can also evaluate 60 Hz systems. It cannot evaluate nominal frequency for 400 Hz systems. The default nominal frequency in the PM850 and the PM870 is 60 Hz. To change the default, from the display Main Menu, select Setup > Meter > Frequency. From SMS software, see the online help file. 4. Reset the EN50160 Statistics. a. Write 9999 in register 8001. b. Write 11100 in register 8000. Refer to “Resetting Statistics” on page 230. © 2006 Schneider Electric All Rights Reserved 241 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix C—EN50160 Evaluation 6/2006 © 2006 Schneider Electric All Rights Reserved 242 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix D—Glossary APPENDIX D—GLOSSARY Terms accumulated energy—energy can “turned off”; i.e, the alarm will not execute accumulates in either signed or unsigned its associated task even when its (absolute) mode. In signed mode, the conditions are met. See also enabled direction of power flow is considered and alarm and active alarm. the accumulated energy magnitude may enabled alarm – an alarm that has been increase and decrease. In absolute mode, configured and “turned on” and will energy accumulates as a positive execute its associated task when its regardless of the power flow direction. conditions are met. See also disabled active alarm – an alarm that has been set alarm and active alarm. up to trigger, when certain conditions are event—the occurrence of an alarm met, the execution of a task or notification. condition, such as Undervoltage Phase A, An icon in the upper-right corner of the configured in the power meter. meter indicates that an alarm is active (!). See also enabled alarm and disabled firmware—operating system within the alarm. power meter baud rate—specifies how fast data is fixed block—an interval selected from 1 transmitted across a network port. to 60 minutes (in 1-minute increments). The power meter calculates and updates block interval demand— power demand the demand at the end of each interval. calculation method for a block of time and includes three ways to apply calculating to float—a 32-bit floating point value that block of time using the sliding block, returned by a register (see Appendix A— fixed block, or rolling block method. Power Meter Register List on page 121). The upper 16-bits are in the lowest- communications link—a chain of numbered register pair. For example, in devices connected by a communications the register 4010/11, 4010 contains the cable to a communications port. upper 16-bits while 4011 contains the current transformer (CT)—current lower 16-bits. transformer for current inputs. frequency—number of cycles in one demand—average value of a quantity, second. such as power, over a specified interval of line-to-line voltages—measurement of time. the rms line-to-line voltages of the circuit. device address—defines where the line-to-neutral voltages—measurement power meter resides in the power of the rms line-to-neutral voltages of the monitoring system. circuit. disabled alarm – an alarm which has been configured but which is currently © 2006 Schneider Electric All Rights Reserved 243 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix D—Glossary 6/2006 maximum demand current—highest phase rotation—phase rotations refers to demand current measured in amperes the order in which the instantaneous since the last reset of demand. values of the voltages or currents of the system reach their maximum positive maximum demand real power—highest values. Two phase rotations are possible: demand real power measured since the A-B-C or A-C-B. last rest of demand. potential transformer (PT)—also known maximum demand voltage—highest as a voltage transformer demand voltage measured since the last reset of demand voltage. power factor (PF)—true power factor is the ratio of real power to apparent power maximum demand (peak demand) — using the complete harmonic content of highest average load during a specific real and apparent power. Calculated by time interval. dividing watts by volt amperes. Power maximum value—highest value recorded factor is the difference between the total of the instantaneous quantity such as power your utility delivers and the portion Phase A Current, Phase A Voltage, etc., of total power that does useful work. since the last reset of the minimums and Power factor is the degree to which maximums. voltage and current to a load are out of phase. minimum value—lowest value recorded of the instantaneous quantity such as real power—calculation of the real power Phase A Current, Phase A Voltage, etc., (3-phase total and per-phase real power since the last reset of the minimums and calculated) to obtain kilowatts. maximums. rms—root mean square. Power meters nominal—typical or average. are true rms sensing devices. parity—refers to binary numbers sent rolling block—a selected interval and over the communications link. An extra bit subinterval that the power meter uses for is added so that the number of ones in the demand calculation. The subinterval must binary number is either even or odd, divide evenly into the interval. Demand is depending on your configuration). Used to updated at each subinterval, and the detect errors in the transmission of data. power meter displays the demand value for the last completed interval. partial interval demand—calculation of energy thus far in a present interval. Equal sag/swell—fluctuation (decreasing or to energy accumulated thus far in the increasing) in voltage or current in the interval divided by the length of the electrical system being monitored. See complete interval. also, voltage sag and voltage swell. phase currents (rms)—measurement in scale factor—multipliers that the power amperes of the rms current for each of the meter uses to make values fit into the three phases of the circuit. See also register where information is stored. maximum value. © 2006 Schneider Electric All Rights Reserved 244 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix D—Glossary safety extra low voltage (SELV) and 4011, 4010 contains the upper 16-bits circuit—a SELV circuit is expected to while 4011 contains the lower 16-bits. always be below a hazardous voltage VAR—volt ampere reactive. level. voltage sag—a brief decrease in effective short integer—a signed 16-bit integer voltage for up to one minute in duration. (see Register List on page 124). voltage swell—increase in effective sliding block—an interval selected from 1 voltage for up to one minute in duration. to 60 minutes (in 1-minute increments). If the interval is between 1 and 15 minutes, the demand calculation updates every 15 seconds. If the interval is between 16 and 60 minutes, the demand calculation updates every 60 seconds. The power meter displays the demand value for the last completed interval. SMS—see System Manager Software. System Manager Software (SMS)— software designed by POWERLOGIC for use in evaluating power monitoring and control data. system type—a unique code assigned to each type of system wiring configuration of the power meter. thermal demand—demand calculation based on thermal response. Total Harmonic Distortion (THD or thd)—indicates the degree to which the voltage or current signal is distorted in a circuit. total power factor—see power factor. true power factor—see power factor. unsigned integer—an unsigned 16-bit integer (see Register List on page 89). unsigned long integer—an unsigned 32- bit value returned by a register (see Register List on page 89). The upper 16- bits are in the lowest-numbered register pair. For example, in the register pair 4010 © 2006 Schneider Electric All Rights Reserved 245 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix D—Glossary 6/2006 Abbreviations and Symbols F—Frequency A—Ampere HARM–Harmonics A IN–Analog Input HEX–Hexadecimal A OUT–Analog Output HIST–History ABSOL–Absolute Value HZ–Hertz ACCUM–Accumulated I—Current ACTIV–Active I/O–Input/Output ADDR—Power meter address IMAX—Current maximum demand ADVAN–Advanced screen kVA—Kilovolt-Ampere AMPS–Amperes kVAD—Kilovolt-Ampere demand BARGR—Bargraph kVAR—Kilovolt-Ampere reactive COINC—Demand values occurring at the same time as a peak demand value kVARD—Kilovolt-Ampere reactive demand COMMS—Communications kVARH—Kilovolt-Ampere reactive hour COND–Conditional Energy Control kW—Kilowatt CONTR–Contrast kWD—Kilowatt demand CPT—Control Power Transformer kWH–Kilowatthours CT—see current transformer on page 243 kWH/P—Kilowatthours per pulse DEC–Decimal kWMAX—Kilowatt maximum demand D IN–Digital Input LANG–Language DIAG–Diagnostic LOWER–Lower Limit DISAB–Disabled MAG–Magnitude DISPL–Displacement MAINT—Maintenance screen D OUT–Digital Output MAMP–Milliamperes DMD—Demand MB A7–MODBUS ASCII 7 Bits DO–Drop Out Limit MB A8–MODBUS ASCII 8 Bits ENABL–Enabled MBRTU–MODBUS RTU ENDOF–End of demand interval MIN—Minimum ENERG–Energy © 2006 Schneider Electric All Rights Reserved 246 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Appendix D—Glossary MINS—Minutes RELAT–Relative value in % MINMX—Minimum and maximum values REG–Register Number MSEC—Milliseconds S—Apparent power MVAh—Megavolt ampere hour S.N.—Power meter serial number MVARh—Megavolt ampere reactive hour SCALE—see scale factor on page 244 MWh—Megawatt hour Sd—Apparent power demand NORM–Normal mode SECON—Secondary O.S.—Operating System (firmware SEC—Secondary version) Sh—Apparent Energy P—Real power SUB-I—Subinterval PAR—Parity SYS—System Manager™ software (SMS) PASSW—Password system type (ID) Pd—Real power demand THD–Total Harmonic Distortion PF—Power factor U—Voltage line to line Ph—Real energy UNBAL–Unbalance PM—Power meter UPPER–Upper limit PQS—Real, reactive, apparent power V—Voltage PQSd—Real, reactive, apparent power VAh–Volt amp hour demand VARh–Volt amp reactive hour PR–Alarm Priority VMAX—Maximum voltage PRIM—Primary VMIN—Minimum voltage PT—Number of voltage connections (see Wh–Watthour potential transformer on page 244) PU–Pick Up Limit PULSE—Pulse output mode PWR–Power Q—Reactive power Qd—Reactive power demand Qh—Reactive energy R.S.—Firmware reset system version © 2006 Schneider Electric All Rights Reserved 247 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Appendix D—Glossary 6/2006 © 2006 Schneider Electric All Rights Reserved 248 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Index INDEX setpoints 75 setup 17, 18 Numerics setup 23 conditional energy 3-wire systems 241 standard 74 controlling from the A test registers 84, 93 command interface 214 accumulate energy types 78 register for 214 signed or unsigned more 54 analog input contacting technical support active alarm log set up 70 117 registers 168–170 analog output 71 controlling relays 64 active evaluations 223 correlation sequence number B address 76 bar graph device address 120 CT setup 29 alarm setup 20 baud rate 120 onboard 223 custom billing log 102 alarm backlight alarms 74, 90 configure log interval 103 setup 29 D data calculation 102 alarm history register list 103 data log 99 registers 170–171 block interval demand method clearing the logs 100 alarm levels 45 forcing data log entries 113 with different pickups and Boolean alarms 90 organizing log files 101 dropouts 91 logic gates 94 storage in power meter 116 alarm log box contents 8 date defining storage space for setup 19 C 114 view 37 description 97 calculating default password 16 alarms duration of an event 76 demand abbreviated names defined watthours per pulse 69 current 48 84, 93 changing generic 50 alarm conditions 73, 83, 92 scale factors 81 predicted 48 alarm groups 74 Channel Selection 107 thermal 48 alarm numbers 84, 93 clock demand current calculation 48 alarm types 84, 85, 92, 93, view 37 demand power 94 clock synchronized demand 47 calculation 45 Boolean 90 command interface demand power calculation creating data log entries 101 changing configuration methods 47 custom alarms 74, 90 registers 213 demand readings 44 digital 74 issuing commands 207 demand current 48 disturbance 90 operating outputs 212 demand power calculation EN50160 Evaluation overview 205 methods 45 positions 230 registers for 205 generic demand 50 introduction to 73 scale factors 219 peak demand 49 levels 91 command synchronized predicted demand 48 multiple alarms 91 demand 47 reset 32 priorities 77 communications demand synch pulse method scaling alarm setpoints 81, problems with PC 63 83 communication 120 device setup in SMS 114 © 2006 Schneider Electric All Rights Reserved 249 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Index 6/2006 diagnostic alarms 4-wire systems 241 H EN50160 Evaluation 223 pass/fail evaluation 227, harmonic diagnostics 228 calculations password 25 portal registers 233 EN50160 Evaluation 230 digital alarms 74 power frequency 224 setting up individual digital inputs 61 register writes 224 calculations 218 digital input alarms 74 setting up 241 values 58 operating modes 62 slow voltage range 224 health status 36 receiving a synch pulse 47 statistics heartbeat LED 119 Digital Inputs screen 61 reset 230 high priority alarms 77 displacement power factor supply voltage 225 Hi-Pot testing 115 described 58 dips 227 I display unbalance 225 I/O menu overview 14 variations 225 position numbers 211 operating 13 system configuration setup 24 disturbance alarms 90 registers 231 incremental energy 215 disturbance monitoring time intervals 230 interval 49 and the utility company 112 timestamp 230 using with the command overview 109 trending and forecasting 230 interface 216 using SMS 114 upstream 229 incremental energy interval dropout and pickup setpoints voltage dips 227 setup 27 75 energy initialize conditional energy registers E power meter 31 214 EN50160 Evaluation input password 25 3-wire systems 241 digital input 61 energy readings 53, 54 accumulation input synchronized demand 47 reactive accumulated 54 interval 227 input/output reset 32 active evaluations 223 setup 24 equipment sensitivity alarm positions 230 inputs disturbance monitoring for allowable events 229 accepting pulse from 111 block read 233 another meter 47 evaluation status 223 block size 233 digital input alarms 74 event log configure day of the week digital inputs operating calculating duration of event 224 modes 62 76 define voltage interruption issuing commands 207 correlation sequence 224 K number 76 depth KY 68 data storage 97 in registers 228 calculating watt hours per F diagnostic alarms 223 pulse 69 enabling 30 features 9 L evaluation status 223 firmware 10 labels harmonic calculations 230 fixed block 45 for inputs and outputs 211 mean rms values 225 floating-point registers language meter cycle 227 enabling 121 changing 117 metered data 224 G setup 20, 117 minimum rms values 227 generic demand calculation 50 LED nominal frequency 224, 241 getting technical support 117 heartbeat 119 nominal voltage 228, 241 © 2006 Schneider Electric All Rights Reserved 250 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Index lock resets on-board logs 95 setup 16 setup 28 operating time with display logic gates for Boolean alarms reset 34 parts 4, 6 94 operating time threshold without display logs 95 set up 25 parts 5 alarm log 97 operation 13 power quality problems 109 billing log 102 problems with the power predicted demand calculation clearing data logs 100 meter 119 48 data log 99 using the command interface problems maintenance log 97 205 see troubleshooting 118 organizing data log files 101 outputs protocols low priority alarms 77 analog 71 register addressing overvoltage alarm type 78 convention 121 M PT P maintenance setup 21 logs 97 password Q maintenance icon 119 default 16 stored log values 97 diagnostics 25 quantities medium priority alarms 77 energy 25 used in alarm levels 91 megger testing 115 minimum/maximum 25 R memory setup 25 read registers 36 power meter memory 116 peak demand calculation 49 readings menu 14 phase loss demand 44 meter information 35 alarm type for current 79 real-time readings 39 metered values alarm type for voltage 79 min/max values 40 demand readings 44 phase reversal alarm type 80 recording energy readings 53 phase rotation data in logs 99 real-time readings 39 setup 26 events in the event log 113 minimum/maximum pickups and dropouts register writes password 25 scale factors 81 EN50160 Evaluation 224 minimum/maximum values setpoints 75 registers reset 33 PLC 1s metering mode synchronizing demand with current 124 reset 33 47 frequency 127 monitoring power analysis values 58, 59 power 125 disturbance 109 power demand configuration power factor 125–127 setup 30 N voltage 124 power factor 58 no priority alarms 77 addressing conventions 121 min/max conventions 42 nominal frequency alarm log storage of 122 EN50160 Evaluation 241 active 168–170 power meter nominal voltage history 170–171 accessories 7 4-wire systems 241 alarms described 3 EN50160 Evaluation 228, boolean 181 firmware 10 241 counters 172–175 hardware 4 non-volatile memory 231 digital 180 initialization 31 nonvolatile memory 116 disturbance 179 instrumentation summary 3 standard speed 176–179 O models 7 system status 172 onboard alarm 223 reset 31 © 2006 Schneider Electric All Rights Reserved 251 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Index 6/2006 template (1) 182 analog output template end of demand interval 65 billing log 103 167–168 kVAh pulse 66 communications auxiliary 155–160 kVAR out pulse 66 RS485 154 discrete input template kVARh in pulse 66 current/voltage configuration 161–162 kWh in pulse 66 146 discrete output template kWh out pulse 66 demand 162–164 latched 65 current channels 138– option modules 160–161 normal 64 139 standard modules 160– timed 65 current configuration and 161 relays data 133–134 metering configuration and internal or external control of generic configuration and status 64 data 136–137 basic 147–148 operating using command generic group 1 channels diagnostics 150–153 interface 207 142–143 harmonics 149 reset input metering channels resets 153 accumulated operating time 141–142 minimum/maximum 34 input metering configura- present group 1 130 demand readings 32 tion and data 135–136 present group 2 131 energy readings 32 miscellaneous configura- previous group 1 130– minimum/maximum values tion and data 137 131 33 power channels 139–141 previous group 2 131 mode 33 power configuration and phase extremes 143 power meter 31 data 134–135 power factor format 122 resets EN50160 Evaluation 223 power quality of peak demand values 49 configuration 231 THD 127–128 values in generic demand portal 233 read 36 profile 50 energy 132–133 spectral components reverse power alarm type 80 cost per shift 202–203 harmonic 189–190 rolling block 45 per shift 200–202 template route statement 120 usage summary 200 data 190–199 S floating-point 121 system configuration 143– sag/swell 1s metering 145 description 110 current 183 templates scale factors 81 energy 184–189 alarms (1) 182 changing scale factors 220 frequency 184 analog input 165–166 scale groups 81 power 183–184 analog output 167–168 scaling alarm setpoints 83 power factor 184 discrete input 161–162 scale groups 81 voltage 183 discrete output 162–164 set up for conditional energy 214 minimum/maximum 131 analog outputs 71 fundamental magnitudes spectral components custom alarms 74, 90 and angles 190–199 individual harmonic current 128 using the command interface calculations 218 sequence components 213 setup 16 129 write 36 alarm backlight 29 input/output relay operating modes alarms 23 analog input template absolute kVARh pulse 66 bar graph 29 165–166 absolute kWh pulse 66 communications 17, 18 © 2006 Schneider Electric All Rights Reserved 252 ® 63230-500-225A1 PowerLogic Series 800 Power Meter 6/2006 Index CT 20 thermal demand method 48 using to detect voltage sag date 19 time 110 I/O 24 setup 19 wiring incremental energy interval view 37 troubleshooting 120 27 time intervals write registers 36 input/output 24 EN50160 Evaluation 230 language 20, 117 total harmonic distortion 58, lock resets 28 106 password 25 transients 109 phase rotation 26 trending and forecasting power demand configuration EN50160 Evaluation 230 30 types of alarms 85, 94 PT 21 U system type 21, 22 unbalance current alarm type THD calculation 27 79 time 19 unbalance voltage alarm type VAR/PF convention 28 79 sliding block 45 undervoltage alarm type 78 SMS 241 V channel selection in 107 VAR device set up 114 sign conventions 43 power meters supported by VAR/PF convention 2 setup 28 using SMS 2 view clock 37 standard alarms 74 view date and time 37 steady-state harmonics 106 viewing meter information 35, synchronized demand 37 clock 47 voltage disturbance monitoring command 47 109 input 47 voltage sag 110 synchronizing power meter capabilities demand interval to internal during 113 clock 47 using waveform captures to demand interval to multiple detect 110 meters 47 voltage swell to PLC command 47 power meter capabilities System Manager Software 3 during 113 see SMS. W system type watthours setup 21, 22 calculating watthours per T KYZ pulse 69 technical support 117 waveform capture 106 testing initiating 107 dielectric (hi-pot) test 115 Waveform Capture dialog 107 megger test 115 waveform captures THD 106 power meter memory 107 setup 27 storage of waveforms 107 thd calculation method 58 © 2006 Schneider Electric All Rights Reserved 253 ® PowerLogic Series 800 Power Meter 63230-500-225A1 Index 6/2006 © 2006 Schneider Electric All Rights Reserved 254 ® PowerLogic Series 800 Power Meter Reference Manual This product must be installed, connected, and used in Schneider Electric compliance with prevailing standards and/or installation Power Monitoring and Control regulations. 295 Tech Park Drive, Suite 100 La Vergne, TN, 37086 As standards, specifications, and designs change from time to time, 1 (615) 287-3400 please ask for confirmation of the information given in this www.schneider-electric.com publication. www.powerlogic.com Este producto deberá instalarse, conectarse y utilizarse en conformidad con las normas y/o los reglamentos de instalación vigentes. Debido a la evolución constante de las normas y del material, es recomendable solicitar previamente confirmación de las características y dimensiones. Ce produit doit être installé, raccordé et utilisé conformément aux normes et/ou aux règlements d’installation en vigueur. En raison de l’évolution des normes et du matériel, les caractéristiques et cotes d’encombrement données ne nous engagent qu’après confirmation par nos services. Publishing: Square D Company PMO Production: Square D Company PMO 6/2006 © 2006 Schneider Electric. All Rights Reserved 63230-500-225A1