DATA SHEET FMP20.24 AC/DC RECTIFIER  Highly efficient topology with power factor correction FEATURES  Wide output voltage range: 23-28.5VDC  High density design: 1.4 kW/l  1U high: 4.2” x 1.6” x 13.3” cassette  RS485 interface status and control  RS485 voltage and current limit setting  Over temperature, output overvoltage and output overcurrent protection, Power limitation DESCRIPTION The FMP20.24 rectifier is a 2000 W, AC to DC power-factor-corrected (PFC) power supply unit that converts standard AC mains power into DC output in the range of 23 - 28.5 VDC for powering telecommunication, data communication and other distributed power applications and can be used in hot-swap redundant systems. The rectifier incorporates resonance-soft-switching technology to reduce component stresses, providing increased system reliability and very high efficiency. A wide variety of distribution options are available to provide the maximum system flexibility for a wide range of communications applications that demand efficiency, reliability, and flexibility including wireless base stations, remote switches and broadband access. Status information is provided with front panel LEDs and via RS485 management interface. The FMP20.24 meets international safety standards and displays the CE-Mark for the European Low Voltage Directive (LVD). BCD.00995_AB1 Oct-29-2013 1 www.power-one.com DATA SHEET TECHNICAL DATA INPUT Voltage Nominal: 85 – 264 VAC Permitted: 85 – 300 VAC Derated Output Power: 85 – 180 VAC Input Current (max.) 13 A Frequency 47 – 63 Hz Power Factor > 0.96 W/VA at > 30 % load OUTPUT Output voltage 23 – 28.5 VDC Power (max.) 2000 W at ≥ 180VAC; 1500 W at ≥ 150 VAC; 1000 W at ≥ 85 VAC Output Current (nom.) 74.6 ADC at ≥ 180 VAC; 62.2 ADC at ≥ 150 VAC; 37.3 ADC at ≥ 85 VAC Efficiency 92.5 % typical at 230 VAC, 50-100% load Capacitive Load < 500 μF/A Tolerance ± 1.0% deviation from programmed set point Dynamic Load Rregulation ± 3.0% for 10-90% or 90-10% load variation Current Sharing < 5 % deviation from average output current Ripple and Noise < 100 mV peak to peak, 20 MHz bandwidth Psophometric Noise < 2 mV (ETS300-132-2) OTHER TECHNICAL DATA Protection Input fuse; Inrush current limitation; Overvoltage protection latching; Programmable over-voltage protection; Over-temperature protection Alarms Fan failure; Temperature alarm / shutdown; Output undervoltage; Module alarm; Overvoltage shut down; Input voltage out of range; Internal communication failure LED Indicators Green AC power ON/OFF (normal operation) Yellow ON: Temperature or fan warning; Yellow Blinking: Communication failure Bicolour Red ON: Temp. shutdown; Fan failure; Overvoltage shutdown DESIGN STANDARDS EMC EN 300 386 V.1.3.2 ; EN 61000-6-3 (Emission) ; EN 61000-6-2 (Immunity); ETSI EN 300 386 V.1.3.2; EN 61000-6-1; EN 61000-6-3; EN55024 (Performance Criterion A); EN 61000-6-2; EN 61000-6-4; EN 55022 Class B; Telcordia NEBS GR1089 Safety Approvals UL60950-1-2011 (CSAus); CSA 60950-1-07+A1-2011; EN60950-1+A12: 2012; IEC 60950-1:2005 2 Ed. +A1:2009 ENVIRONMENTAL Storage: ETSI EN 300 019-2-1 Transport: ETSI EN 300 019-2-2 Operation: ETSI EN 300 019-2-3 Damp Heat: IEC 60068-2-78 Operating Temperature and Altitude -40°C to +55°C up to 2000 m; Reduced spec.: -40°C to -20°C Extended Temperature and Altitude Linear derating from 100% to 70% maximum power at 55 to 65°C Reduced ambient temperatures by 5°C at 3000 m Storage Temperature -40 ºC to +85 ºC Audible Noise < 54.5 dBA @ at 230 VAC; TA = 25°C (70% load) MTBF 350 kh at GB 25°C, fan excluded MECHANICAL Dimensions (W x H x D) 106.8 x 41.4 x 355.1 mm (4.2 x 1.6 x 11.3 inch) Weight 2.1 kg (4.7 lb) Mounting / Integration 1U Rack mount (19in/4 pos, 23in/5 pos) Cooling Fan cooled (front to rear airflow), speed controlled Insulation Reinforced insulation 3000 VAC from input to output Enclosure IP20 NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of Power-One, Inc. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. FMP20.24 AC/DC RECTIFIER 2 www.power-one.com