S S SENS. SENS. E EN NS S.. E E EX EX X X -17 -17 -1 -17 7 EX-10 SERIES Amplifier Built-in Ultra-slim Photoelectric Sensor PNP output Light intensity type available monitor Amplifier built-in extraordinarily small and slim size UL Recognition Conforming to EMC Directive (Excluding EX-15�/17�) (Excluding 5 m cable length type) Smallest body, just 3.5 mm 0.138 in thick High-speed response time: 0.5 ms Flexible mounting It can be mounted in a very small space The sensor is suitable for detecting The diffuse reflective type sensor is as its size is just W10�H14.5�D3.5 mm small and high-speed traveling objects. front sensing and is so thin that it gives W0.394� H0.571�D0.138 in (thru- an impression of being just pasted on beam, front sensing type). the mounting base. The thru-beam type is available as front sensing type, as well as, side sensing type, allowing flexible mounting. Diffuse reflective • Front sensing type Thru-beam • Front sensing type • Side sensing type Bright 2-color indicator Waterproof Operation mode switch A convenient 2-color indicator has The sensor can be hosed down Thru-beam type sensor incorporated been incorporated in the miniature because of its IP67 construction and with an operation mode switch on the body. the non-corrosive stainless steel bifurcation is also available. It helps mounting bracket. you to test the operability before start- Note: However, take care that if it is exposed to up. water splashes during operation, it may 2-color indicator detect a water drop itself. Red: Operation indicator ( ) Green: Stability indicator Operation mode switch Even for the thru-beam type sensor, only three Ten times durable Red beam makes beam alignment easy Operation indicator wires have to be con- (Orange) nected. Flexible cable on EX-10-R is 10 times The red LED beam projected from the as durable as conventional model. It is emitter helps you to align the sensor most suitable for moving parts, such heads. as robot arm, etc. 232 RX-LS200 RX EX-40 EQ-30 EQ-20 EX-10 EX-20 EX-30 CX-400 PHOTOELECTRIC SENSORS Amplifier Built-in EX-10 APPLICATIONS Verifying position of PCBs Detecting ICs Detecting PCB rack EX-19� Transparent stick IC EX-15 EX-14� Detecting wafer cassette Detecting thin ring Checking for absence of capacitor in tray EX-14� EX-13E� Guide EX-14� Mountable with M3 screws Minimum sensing object: "1 mm "0.039 in Long sensing range: 1 m 3.281 ft (EX-19�) Non-corrosive stainless steel type EX-11�, EX-11E�, EX-15 and EX-15E A sensing range of 1 m 3.281 ft has mounting bracket is also available. are incorporated with "1 mm "0.039 in been realized with a slim size of just slit masks so that "1 mm "0.039 in, or 3.5 mm 0.138 in. It can be used to • MS-EX10-1 [Cold rolled carbon steel (SPCC)] more, object can be detected. Hence, detect even wide IC trays. and MS-EX10-11 [Stainless steel (SUS304)] (mounting bracket for the front sensing type) they are suitable for precise positioning or small parts detection. 1 m 3.281 ft M3 screws • MS-EX10-2 [Cold rolled carbon steel (SPCC)] and MS-EX10-12 [Stainless steel (SUS304)] (mounting bracket for the side sensing type) Background suppression (EX-14�) • Not affected by background • Black object reliably detected Even a specular background sepa- It can reliably detect dark color ob- rated by 100 mm 3.937 in, or more, jects since it is convergent reflective is not detected. type. However, the background should be () M3 screws directly opposite. The best distance is approx. 10 mm 0.394 in • MS-EX10-3 [Cold rolled carbon steel (SPCC)] from the object. and MS-EX10-13 [Stainless steel (SUS304)] (L-shaped mounting bracket) M3 screws Background 100 mm 3.937 in 233 Amplifier Built-in PHOTOELECTRIC SENSORS RX-LS200 RX EX-40 EQ-30 EQ-20 EX-10 EX-20 EX-30 CX-400 EX-10 ORDER GUIDE Type Appearance Sensing range Model No. Output operation Output Light-ON EX-11A 150 mm 5.906 in Dark-ON EX-11B Light-ON EX-13A 500 mm 19.685 in EX-13B Dark-ON Light-ON EX-19A 1 m 3.281 ft Dark-ON EX-19B 150 mm 5.906 in EX-15 Switchable either Light-ON or Dark-ON 500 mm EX-17 19.685 in Light-ON EX-11EA NPN open-collector transistor 150 mm 5.906 in Dark-ON EX-11EB EX-13EA Light-ON 500 mm 19.685 in Dark-ON EX-13EB 150 mm 5.906 in EX-15E Switchable either Light-ON or Dark-ON 500 mm EX-17E 19.685 in Light-ON EX-14A 2 to 25 mm 0.079 to 0.984 in (Note) (Convergent point: 10 mm 0.394 in) Dark-ON EX-14B Light-ON EX-11A-PN 150 mm 5.906 in Dark-ON EX-11B-PN EX-13A-PN Light-ON 500 mm 19.685 in EX-13B-PN Dark-ON Light-ON EX-19A-PN 1m 3.281 in Dark-ON EX-19B-PN EX-11EA-PN Light-ON 150 mm 5.906 in PNP open-collector transistor EX-11EB-PN Dark-ON Light-ON EX-13EA-PN 500 mm 19.685 in Dark-ON EX-13EB-PN Light-ON EX-14A-PN 2 to 25 mm 0.079 to 0.984 in (Note) (Convergent point: 10 mm 0.394 in) EX-14B-PN Dark-ON NOTE: Mounting bracket is not supplied with the sensor. Please select from the range of optional sensor mounting brackets (six types). Note: The sensor does not detect even a specular background if it is separated by 100 mm 3.937 in or more. (However, the background should be directly opposite.) 234 RX-LS200 RX EX-40 EQ-30 EQ-20 EX-10 EX-20 EX-30 CX-400 PHOTOELECTRIC SENSORS Amplifier Built-in PNP output NPN output Convergent Convergent reflective Thru-beam reflective Thru-beam (Diffused beam type) (Diffused beam type) Side sensing Front sensing Front sensing Side sensing Front sensing Front sensing With operation mode With operation mode switch on the bifurcation switch on the bifurcation EX-10 ORDER GUIDE Flexible cable type and 5 m 16.404 ft cable length type Flexible cable type and 5 m 16.404 ft cable length type (standard: 2 m 6.562 ft) are also available. • Table of model Nos. Type Standard Flexible cable (2 m 6.562 ft) type 5 m 16.404 ft cable length type EX-11A EX-11A-R EX-11A-C5 EX-11B EX-11B-R EX-11B-C5 EX-13A EX-13A-R EX-13A-C5 Front sensing EX-13B EX-13B-R EX-13B-C5 EX-19A EX-19A-R EX-19A-C5 EX-19B EX-19B-R EX-19B-C5 With operation EX-15 EX-15-C5 Thru-beam mode switch on the bifurcation EX-17 EX-17-C5 EX-11EA EX-11EA-R EX-11EA-C5 EX-11EB EX-11EB-R EX-11EB-C5 Side sensing EX-13EA EX-13EA-R EX-13EA-C5 EX-13EB EX-13EB-R EX-13EB-C5 With operation EX-15E EX-15E-C5 mode switch on the bifurcation EX-17E EX-17E-C5 Convergent EX-14A-C5 EX-14A EX-14A-R reflective Front sensing (Diffused beam type) EX-14B EX-14B-R EX-14B-C5 235 Amplifier Built-in PHOTOELECTRIC SENSORS RX-LS200 RX EX-40 EQ-30 EQ-20 EX-10 EX-20 EX-30 CX-400 CHX-SC2 POWER LEVEL EX-10 OPTIONS Sensor mounting bracket Designation Model No. Description • MS-EX10-1 • MS-EX10-11 Mounting bracket for the front sensing type sensor [Cold rolled carbon steel (SPCC)] MS-EX10-1 (The thru-beam type sensor needs two brackets.) Mounting bracket for the side sensing type sensor [Cold rolled carbon steel (SPCC)] MS-EX10-2 (The thru-beam type sensor needs two brackets.) L-shaped mounting bracket sensor [Cold rolled carbon steel (SPCC)] Sensor MS-EX10-3 (The thru-beam type sensor needs two brackets.) mounting Material: Cold rolled carbon Material: Stainless steel (SUS304) bracket steel (SPCC) Two M2 (length 4 mm 0.157 in) Mounting bracket for the front sensing type sensor [Stainless steel (SUS304)] MS-EX10-11 (Uni-chrome plated) pan head screws [stainless steel (The thru-beam type sensor needs two brackets.) Two M2 (length 4 mm 0.157 in) (SUS304)] are attached. pan head screws are attached. Mounting bracket for the side sensing type sensor [Stainless steel (SUS304)] MS-EX10-12 (The thru-beam type sensor needs two brackets.) • MS-EX10-2 • MS-EX10-12 L-shaped mounting bracket [Stainless steel (SUS304)] MS-EX10-13 (The thru-beam type sensor needs two brackets.) � Sensing range: 600 mm 23.622 in [EX-19�] Slit on one side 250 mm 9.843 in [EX-13�, EX-17] � Min. sensing object: "2 mm "0.079 in OS-EX10-12 (Slit size "1.2 mm "0.047 in) � Sensing range: 400 mm 15.748 in [EX-19�] Slit on both sides 200 mm 7.874 in [EX-13�, EX-17] � Min. sensing object: 1.2 mm 0.047 in " " Material: Cold rolled carbon Material: Stainless steel (SUS304) steel (SPCC) Two M2 (length 8 mm 0.315 in) � Sensing range: 800 mm 31.496 in [EX-19�] (Uni-chrome plated) pan head screws [stainless steel Slit on one side 350 mm 13.780 in [EX-13�] Two M2 (length 8 mm 0.315 in) (SUS304)] are attached. � Min. sensing object: "2 mm "0.079 in OS-EX10-15 pan head screws are attached. Slit mask (Slit size 1.5 mm 0.059 in) " " � Sensing range: 500 mm 19.685 in [EX-19�] Slit on both sides 300 mm 11.811 in [EX-13�] • MS-EX10-3 • MS-EX10-13 � Min. sensing object: 1.5 mm 0.059 in " " � Sensing range: 250 mm 9.843 in [EX-13E�, EX-17E] Slit on one side � Min. sensing object: "2 mm "0.079 in OS-EX10E-12 (Slit size 1.2 mm 0.047 in) " " � Sensing range: 200 mm 7.874 in [EX-13E�, EX-17E] Slit on both sides � Min. sensing object: "1.2 mm "0.047 in It is useful for beam alignment of thru-beam type sensors. Sensor checker The optimum receiver position is given by indicators, as CHX-SC2 Material: Cold rolled carbon Material: Stainless steel (SUS304) (Note) well as an audio signal. steel (SPCC) Two M2 (length 4 mm 0.157 in) (Uni-chrome plated) pan head screws [stainless steel Mounting screws with washers (50 pcs. lot). It can mount Two M2 (length 4 mm 0.157 in) (SUS304)] and two M2 (length Mounting screw MS-M2 securely as it is spring washer attached. pan head screws, and two 8 mm 0.315 in) pan head screws M2 (length 8 mm 0.315 in) [stainless steel (SUS304)] are pan head screws are attached. attached. Note: Refer to p.414l for details of the sensor checker CHX-SC2. Slit mask • OS-EX10-12 • OS-EX10E-12 • OS-EX10-15 Example of mounting (OS-EX10E-12) Tighten along with the sensor mounting bracket. Sensor checker • CHX-SC2 Sensor checker 236 RX-LS200 RX EX-40 EQ-30 EQ-20 EX-10 EX-20 EX-30 CX-400 PHOTOELECTRIC SENSORS Amplifier Built-in EX-10 SPECIFICATIONS Convergent reflective Thru-beam Thru-beam • with operation mode switch on bifurcation (Diffused beam type) Type Front sensing Side sensing Front sensing Side sensing Front sensing Front sensing Front sensing Side sensing Front sensing Side sensing Model Light-ON EX-11A(-PN) EX-11EA(-PN) EX-13A(-PN) EX-13EA(-PN) EX-19A(-PN) EX-14A(-PN) EX-15 EX-15E EX-17 EX-17E No. (Note 2) (Note 2) (Note 2) (Note 2) EX-11B(-PN) EX-11EB(-PN) EX-13B(-PN) EX-13EB(-PN) EX-19B(-PN) EX-14B(-PN) Item (Note 1) Dark-ON 2 to 25 mm 0.079 to Sensing range 0.984 in (Note 3) 150 mm 5.906 in 500 mm 19.685 in 1 m 3.281 ft 150 mm 5.906 in 500 mm 19.685 in (Conv. point: 10 mm 0.394 in) "2 mm "0.079 in "1 mm "0.039 in opaque object "2 mm "0.079 in opaque object "0.1 mm "0.004 in "1 mm "0.039 in opaque object "2 mm "0.079 in opaque object opaque object Setting distance between Setting distance between copper wire Setting distance between Setting distance between Min. sensing object Setting distance between emitter and receiver: emitter and receiver: Setting distance: emitter and receiver: emitter and receiver: ()() emitter and receiver: ()() () 150 mm 5.906 in 500 mm 19.685 in () 10 mm 0.394 in 150 mm 5.906 in 500 mm 19.685 in 1 m 3.281 ft 15 % or less of Hysteresis operation distance 0.1 mm 0.004 in Repeatability 0.05 mm 0.002 in or less 0.05 mm 0.002 in or less or less (perpendicular to sensing axis) Supply voltage 12 to 24 V DC�10 % Ripple P-P 10 % or less Current consumption Emitter: 10 mA or less, Receiver: 15 mA or less 20 mA or less 30 mA or less NPN open-collector transistor NPN open-collector transistor • Maximum sink current: 50 mA • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between output and 0 V) • Applied voltage: 30 V DC or less • Residual voltage: 1 V or less (at 50 mA sink current) (between output and 0 V) 0.4 V or less (at 16 mA sink current) Output • Residual voltage: 1.5 V or less (at 100 mA sink current) PNP open-collector transistor • Residual voltage: 0.4 V or less • Maximum source current: 50 mA (at 16 mA sink current) • Applied voltage: 30 V DC or less (between output and�V) • Residual voltage: 1 V or less (at 50 mA source current) 0.4 V or less (at 16 mA source current) Utilization category DC-12 or DC-13 Short-circuit protection Incorporated Response time 0.5 ms or less Orange LED (lights up when the output is ON), Operation indicator Red LED (lights up when the output is ON) located on the bifurcation Red LED (lights up under light received condition), Incident beam indicator located on the receiver Green LED (lights up under stable light received condition or Green LED (lights up under stable light received condition Stability indicator stable dark condition) or stable dark condition), located on the receiver Pollution degree 3 (Industrial environment) Protection IP67 (IEC) Ambient temperature �25 to�55 �C �13 to�131 �F (No dew condensation or icing allowed), Storage:�30 to�70 �C �22 to�158 �F Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH Ambient illuminance Sunlight: 10,000 ?x at the light-receiving face, Incandescent light: 3,000 ?x at the light-receiving face EMC EN 50081-2, EN 50082-2, EN 60947-5-2 Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure Insulation resistance 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure Vibration resistance 10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each 2 Shock resistance 500 m/s acceleration (50 G approx.) in X, Y and Z directions for three times each Emitting element Red LED (modulated) Enclosure: Polyethylene terephthalate Enclosure: Polyethylene terephthalate Material Lens: Polyalylate Lens: Polyalylate, Bifurcation: Polyalylate 2 0.2 mm 3-core cabtyre cable, 2 m 6.562 ft long (beyond bifur- 2 Cable (Note 4) 0.1 mm 3-core (thru-beam type emitter: 2-core) cabtyre cable, 2 m 6.562 ft long cation; from emitter / receiver to bifurcation: 0.5 m 1.640 ft long) 2 Extension up to total 50 m 164.042 ft is possible with 0.3 mm , or more, cable Extension up to total 100 m 328.084 ft is Cable extension 2 (thru-beam type: emitter and receiver). possible with 0.3 mm , or more, cable. Weight Emitter: 20 g approx., Receiver: 20 g approx. 20 g approx. 55 g approx. Mounting screws: Accessories Mounting screws: 1 set Mounting screws: 1 set, Adjusting screwdriver: 1 pc. 1 set Notes: 1) Model Nos. having the suffix ‘-PN’ are PNP output type. Notes: 2) Either Light-ON or Dark-ON can be selected by the operation mode switch (located on the bifurcation). Notes: 3) The sensing range of convergent reflective type sensor is specified for white non-glossy paper (50�50 mm 1.969�1.969 in) as the object. 2 Notes: 4) The flexible cable type (model Nos. having suffix ‘-R’) has a 0.1 mm 3-core (thru-beam type emitter : 2-core) flexible cabtyre cable, 2 m 6.562 ft long. 237 Environmental resistance Amplifier Built-in PHOTOELECTRIC SENSORS RX-LS200 RX EX-40 EQ-30 EQ-20 EX-10 EX-20 EX-30 CX-400 EX-10 I/O CIRCUIT AND WIRING DIAGRAMS EX-11� EX-13� NPN output type EX-19� EX-14� I/O circuit diagram Wiring diagram Color code D (Brown)�V Load (Black) � Output (Note) 12 to 24 V DC Brown �10 % � Tr 50 mA max. ZD Load � Black (Note) 12 to 24 V DC (Blue) 0 V �10 % � Blue Internal circuit Users’ circuit Note: The emitter of the thru-beam type sensor does not Note: The emitter of the thru-beam type sensor does not incorporate the output. incorporate the black wire. Symbols … D : Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : NPN output transistor EX-11�-PN EX-13�-PN PNP output type EX-19�-PN EX-14�-PN I/O circuit diagram Wiring diagram Color code (Brown)�V ZD 50 mA max. � 12 to 24 V DC Brown Tr �10 % (Black) Output (Note) � Load � Black (Note) 12 to 24 V DC D (Blue) 0 V �10 % � Load Blue Internal circuit Users’ circuit Note: The emitter of the thru-beam type sensor does not Note: The emitter of the thru-beam type sensor does not incorporate the output. incorporate the black wire. Symbols … D : Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : PNP output transistor EX-15 EX-15E NPN output type EX-17 EX-17E I/O circuit diagram Wiring diagram Color code D (Brown)�V Load � (Black) Output 12 to 24 V DC �10 % � Tr 100 mA max. ZD (Blue) 0 V Internal circuit Users’ circuit Symbols … D : Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : NPN output transistor Brown Load � Black 12 to 24 V DC �10 % � Blue 238 RX-LS200 RX EX-40 EQ-30 EQ-20 EX-10 EX-20 EX-30 CX-400 PHOTOELECTRIC SENSORS Amplifier Built-in Sensor circuit Sensor circuit Sensor circuit EX-10 SENSING CHARACTERISTICS (TYPICAL) All models Thru-beam type Correlation between setting distance and excess gain 100 100 50 50 EX-13� EX-17� EX-19� 10 10 5 5 EX-11� EX-15� 1 1 0 200 400 600 800 1,000 01 2 3 4 5 7.874 15.748 23.622 31.496 39.370 3.281 6.562 9.843 13.123 16.404 Setting distance L (mm in) Setting distance L (m ft) EX-11� EX-11E� Thru-beam type EX-15� EX-15E� Parallel deviation Angular deviation 200 200 7.874 7.874 EX-11� 150 150 EX-15� EX-11� 5.906 5.906 EX-11E� EX-15� EX-15E� EX-11� EX-11E� 100 100 EX-15� EX-11E� EX-15E� 3.937 3.937 EX-15E� Emitter Emitter Emitter Emitter 50 50 # # L $ $ L 1.969 1.969 L L EX-11� EX-11E� Receiver Receiver EX-15� EX-15E� Receiver Receiver 0 0 100 50 050 100 20 10 0 10 20 3.937 1.969 1.969 3.937 Left Center Right Left Center Right $ Operating angle ( ° ) Operating point ?(mm in) EX-13� EX-13E� Thru-beam type EX-17� EX-17E� Parallel deviation Angular deviation Parallel deviation with slit masks ("1.2 mm "0.047 in) Parallel deviation with slit masks ("1.5 mm "0.059 in) 800 800 400 400 EX-13�/17� 31.496 31.496 Slit on one side 15.748 15.748 Slit on one side or both sides EX-13�/17� 600 EX-13� 600 300 Slit on both sides 300 23.622 23.622 EX-17� 11.811 11.811 EX-13E�/17E� EX-13� EX-13E� Slit on one side EX-17� EX-17E� EX-13E�/17E� 400 400 200 200 EX-13E� Slit on 15.748 Emitter 15.748 7.874 7.874 Slit on one side, EX-17E� both sides Emitter Emitter Emitter sensing range: 350 mm 13.78 in Emitter Slit on both sides, Emitter # 200 L 200 100 100 sensing range: 300 mm 11.81 in $ $ # # # L L L 7.874 7.874 L L 3.937 3.937 EX-13� EX-13E� EX-13� EX-13E� Receiver Receiver Receiver Receiver EX-17� Receiver EX-17E� EX-17� EX-17E� Receiver 0 0 0 0 100 50 050 100 20 10 0 10 20 40 20 020 40 100 50 050 100 3.937 1.969 1.969 3.937 1.575 0.787 0.787 1.575 3.937 1.969 1.969 3.937 Left Center Right Left Center Right Left Center Right $ Left Center Right Operating angle ( ° ) Operating point ?(mm in) Operating point ?(mm in) Operating point ?(mm in) EX-19� Thru-beam type Parallel deviation Angular deviation Parallel deviation with slit masks ("1.2 mm "0.047 in) Parallel deviation with slit masks ("1.5 mm "0.059 in) 800 31.496 Slit on one side Slit on one side 1,000 1,000 1,000 600 39.370 39.370 39.370 23.622 Slit on both sides 400 15.748 Emitter Emitter 500 500 500 Emitter Emitter 19.685 19.685 19.685 $ L # 200 L # L # L 7.874 Slit on both sides Receiver Receiver Receiver Receiver 0 0 0 0 200 100 0 100 200 40 20 0 20 40 200 100 0 100 200 200 100 0 100 200 7.874 3.937 3.937 7.874 7.874 3.937 3.937 7.874 7.874 3.937 3.937 7.874 Left Center Right Left Center Right Left Center Right Left Center Right $ Operating angle ( � ) Operating point ?(mm in) Operating point ?(mm in) Operating point ?(mm in) 239 Setting distance L (mm in) Setting distance L (mm in) Setting distance L (mm in) Excess gain Setting distance L (mm in) Setting distance L (mm in) Excess gain Setting distance L (mm in) Setting distance L (mm in) Setting distance L (mm in) Setting distance L (mm in) Setting distance L (mm in) Amplifier Built-in PHOTOELECTRIC SENSORS RX-LS200 RX EX-40 EQ-30 EQ-20 EX-10 EX-20 EX-30 CX-400 EX-10 SENSING CHARACTERISTICS (TYPICAL) EX-14� Convergent reflective type Sensing fields • Horizontal (left and right) direction • Vertical (up and down) direction 40 40 50�50 mm 1.969�1.969 in 1.575 1.575 Non-glossy paper 30 30 # 7 mm 1.181 1.181 50�50 mm 0.276 in 1.969�1.969 in L White Non-glossy paper 20 20 0.787 0.787 White 10 10 # 0.394 0.394 7.75 N4 N4 mm L 0.305 in 0 0 10 5 05 10 10 5 05 10 0.394 0.197 0.197 0.394 0.394 0.197 0.197 0.394 Down Center Up Left Center Right Operating point ?(mm in) Operating point ?(mm in) Correlation between lightness and sensing range Correlation between material (50 �50 mm 1.969�1.969 in) and sensing range 40 80 The sensing region is represent- The bars in the graph indicate the 1.575 3.150 ed by oblique lines in the left sensing range for the respective figure. However, the sensitivity material. However, there is a 30 60 1.181 should be set with enough mar- slight variation in the sensing 2.362 gin because of slight variation in range depending on the product. 20 products. Further, if there is a reflective 40 0.787 1.575 object (conveyor, etc.) in the Sensing region background of the sensing object, 10 20 since it affects the sensing, 0.394 0.787 separate it by more than twice the 10 sensing range shown in the left 0.394 0 0 graph. N2 N4 N6 N8 Lightness shown on the left Dark Lightness Light may differ slightly from the () actual object condition. N1 N2 N3 N4 N5 N6 N7 N8 N9 PRECAUTIONS FOR PROPER USE Refer to p.1135l for general precautions. Operation mode switch (EX-15�, EX-15E�, EX-17� and EX-17E� only) This product is not a safety sensor. Its use is not intended or designed to protect life and prevent body Operation mode switch injury or property damage from dangerous parts of L : Light-ON machinery. It is a normal object detection sensor. D: Dark-ON Mounting Operation indicator (Orange) • In case of mounting on tapped holes (Unit: mm in) Lights up when the output is ON. Side sensing Front sensing Sensing Switch Sensing 11 Description direction direction position 0.433 Attached 11 Attached screw screw 0.433 [M2 (length 8 0.315)] Light-ON mode is set when the switch is turned fully [M2 (length 10 0.394)] M2�0.4 0.016 hole M2�0.4 0.016 hole clockwise (L side). tapped, 7 0.276 deep tapped, 6 0.157 deep The tightening torque should be 0.2 N �m or less. Dark-ON mode is set when the switch is turned fully counterclockwise (D side). • In case of using attached screws and nuts (Unit: mm in) Side sensing Front sensing Flat washers Others Sensing Sensing 11 direction • Do not use during the initial transient time (50ms) Nuts direction 0.433 Attached Spring (EX-15�, EX-15E�, EX-17�, EX-17E�: 100 ms) after 11 Attached screw washers screw 0.433 the power supply is switched on. [M2 (length 10 0.394)] [M2 (length 8 0.315)] Thickness of Thickness of mounting plate: 2 0.079 or less mounting plate: 2.5 0.098 or less The tightening torque should be 0.2 N �m or less. 240 RX-LS200 RX EX-40 EQ-30 EQ-20 EX-10 EX-20 EX-30 CX-400 PHOTOELECTRIC SENSORS Amplifier Built-in Setting distance L (mm in) Sensing range L (mm in) Distance to convergent point Setting distance L (mm in) Sensing range L (mm in) Black circuit board Black rubber sheet IC tray (Black) Glass epoxy printed circuit board (Green masked surface) Ceramic circuit board White non-glossy paper Stainless steel plate Aluminum plate (Hair line) Aluminum-evaporated mirror Distance to convergent point EX-10 DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ EX-11A� EX-11B� EX-13A� Sensor EX-13B� EX-19A� EX-19B� Stability 10 3.5 0.394 indicator 3.5 0.138 6.45 (Green) 10 0.138 0.254 2.1 0.394 5.5 Operation 2.1 0.083 5.5 0.217 0.083 indicator 1.75 0.217 (Red) 0.069 1.75 0.069 1.75 1.5 0.069 0.059 1.75 0.069 4 4 Beam- 0.157 0.157 receiving 11 11 14.5 14.5 part 0.433 0.433 0.571 0.571 Beam- 4.5 4.5 0.177 emitting 0.177 part 6.5 2-"2.2 "0.087 6.5 2-"2.2 "0.087 0.256 0.256 mounting holes mounting holes "2.5 "0.098 cable, 2 m 6.562 ft long "2.5 "0.098 cable, 2 m 6.562 ft long Emitter Receiver EX-11EA� EX-11EB� Sensor EX-13EA� EX-13EB� Stability indicator (Green) 10 Operation 0.394 6.45 indicator (Red) 0.254 10 4.5 1.75 4.5 0.394 0.177 0.069 0.177 1.75 0.069 2.25 1.75 1.5 2.25 0.089 0.069 0.059 1.75 0.069 0.089 Beam- 4 4 Beam- 0.157 0.157 receiving emitting 14.5 11 14.5 11 part part 0.571 0.433 0.571 0.433 4.5 4.5 0.177 0.177 6.5 2-"2.2 "0.087 6.5 2-"2.2 "0.087 0.256 0.256 mounting holes 4.2 mounting holes 4.2 0.165 0.165 "2.5 "0.098 cable, 2 m 6.562 ft long "2.5 "0.098 cable, 2 m 6.562 ft long Emitter Receiver EX-15 EX-15E Sensor Sensor EX-17 EX-17E Emitter Receiver Emitter Receiver 10 Stability indicator (Green) 10 Stability indicator (Green) 10 0.394 1.75 0.394 Incident beam indicator (Red) 0.394 Incident beam indicator (Red) 6.45 0.254 0.069 5.5 4.5 4.5 1.75 1.75 0.069 10 0.394 0.217 3.5 1.75 3.5 0.177 1.5 0.177 1.75 0.069 4 6.45 0.254 4 0.138 0.069 0.138 2.25 0.059 2.25 0.069 1.5 0.157 1.75 1.75 5.5 0.157 4 0.089 1.75 0.089 0.059 2.1 0.069 0.069 0.217 2.1 0.157 0.069 Beam- Beam- 0.083 14.5 0.083 11 11 14.5 emitting receiving 0.571 0.571 Beam- 4 0.157 0.433 0.433 14.5 11 Beam- 11 14.5 part part receiving 0.571 0.433 emitting 0.571 0.433 4.5 0.177 part part 4.5 0.177 4.5 0.177 4.5 4.2 4.2 2-"2.2 "0.087 0.177 2-"2.2 "0.087 0.165 0.165 mounting holes 2-"2.2 "0.087 mounting holes 500 2-"2.2 "0.087 500 19.685 mounting holes mounting holes 19.685 "2.5 "0.098 cables "2.5 "0.098 cables 15.2 0.598 15.2 0.598 Operation indicator 19.2 19.2 Operation indicator 0.756 (Orange) 0.756 (Orange) 38 38 1.496 1.496 Operation mode switch Operation mode switch "3.8 "0.150 cable, "3.8 "0.150 cable, 2 m 6.562 ft long 2 m 6.562 ft long 8 1 0.039 8 1 0.039 7 0.315 7 0.315 0.276 0.276 241 Amplifier Built-in PHOTOELECTRIC SENSORS RX-LS200 RX EX-40 EQ-30 EQ-20 EX-10 EX-20 EX-30 CX-400 EX-10 DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ EX-14A� Sensor EX-14B� 13 0.512 6.45 Stability indicator 0.254 2.75 (Green) 3.5 5 0.108 0.138 Operation 0.197 1.75 2.1 indicator (Red) 0.069 0.083 1.75 1.5 0.069 0.059 4.5 Beam- 0.177 11 14.5 receiving 0.433 0.571 part Beam-emitting part 4.5 0.177 8 0.315 2-"2.2 "0.087 mounting holes "2.5 "0.098 cable, 2 m 6.562 ft long MS-EX10-1 Sensor mounting bracket (Optional) Assembly dimensions Mounting drawing with EX-14� t 1.2 7.6 t 0.047 0.299 20 0.787 (0.7) t 1.2 (0.028) t 0.047 7.6 0.299 3.7 0.146 3.7 3.5 (4.9) 0.146 0.138 (0.193) 22.75 0.896 13 20 0.512 0.787 10.75 3.5 5 6.5 8 3.5 0.423 4-M2�0.4 0.016 0.138 0.197 0.256 0.315 0.138 8 1.25 thru-hole threads Beam- 2-"3.4 "0.134 mounting holes 0.315 (8.8) 0.049 emitting (0.346) part 11 8 15 3 0.118 11 15 Beam- 8 0.433 0.315 0.591 0.433 0.591 0.315 receiving part 4.25 0.167 Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated) 2-"3.4 "0.134 mounting holes Two M2 (length 4 mm 0.157 in) pan head screws are attached. MS-EX10-2 Sensor mounting bracket (Optional) Assembly dimensions t 1.2 Mounting drawing with EX-11E� and EX-13E� 7.6 t 0.047 0.299 (2.3) 7.6 (0.091) t 1.2 0.299 6.25 t 0.047 0.246 4.5 (7.45) 6.25 0.177 (0.293) 0.246 20 0.787 (1.3) 3.2 1.4 3.2 (0.051) 0.126 0.055 0.126 4 0.25 10 1.25 0.157 0.010 0.394 0.049 1.4 0.055 11 8 15 Beam- 2.5 0.098 0.433 0.315 0.591 15 11 receiving 8 0.591 0.433 0.315 part 2-M2�0.4 0.016 4.25 thru-hole threads 8 3.5 0.167 0.315 0.138 3.5 8 0.138 0.315 Material: Cold rolled carbon steel (SPCC) 20 (Uni-chrome plated) 0.787 Two M2 (length 8 mm 0.315 in) pan head screws are attached. 242 RX-LS200 RX EX-40 EQ-30 EQ-20 EX-10 EX-20 EX-30 CX-400 PHOTOELECTRIC SENSORS Amplifier Built-in EX-10 DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ MS-EX10-3 Sensor mounting bracket (Optional) Assembly dimensions Mounting drawing with EX-14� 15 0.591 (2.75) 10.8 t 1.2 (0.108) 0.425 t 0.047 7 0.276 10.5 0.413 (0.7) (0.028) 3.2 1.4 0.126 3.5 0.055 10.5 8 0.138 0.413 4-M2�0.4 0.016 3.2 t 1.2 0.315 Beam- thru-hole threads Beam- 0.126 t 0.047 1.75 0.069 13 7 emitting part receiving part 0.512 0.276 5 6.25 1.25 0.197 0.246 0.049 1.4 0.055 10.8 6.5 0.425 0.256 3 0.118 11 8 15 0.438 0.315 0.591 11 2 0.433 0.079 4.25 Material: Cold rolled carbon steel (SPCC) 0.167 (Uni-chrome plated) Two M2 (length 4 mm 0.157 in) pan head screws, and two M2 (length 8 mm 0.315 in) pan head screws are attached. MS-EX10-11 Sensor mounting bracket (Optional) Assembly dimensions Mounting drawing with EX-14� t 1.2 8.1 20 t 0.047 0.319 0.787 (0.7) t 1.2 8.1 (0.028) t 0.047 0.319 (4.9) (0.193) 3.7 0.146 20 22.75 3.5 0.787 3.7 4-M2�0.4 0.016 0.896 6.5 8 3.5 0.138 0.146 13 3.2 thru-hole threads 0.256 0.315 0.138 1.4 0.512 0.126 0.055 5 3.5 10.75 0.423 0.197 0.138 8 0.315 (9.3) 11 3.2 8 15 1.25 (0.366) 0.433 0.126 0.315 0.591 0.049 1.4 0.055 Beam-emitting part 3.2 1.4 3 0.118 0.126 0.055 8 11 15 0.315 0.433 0.591 Material: Stainless steel (SUS304) Beam-receiving part Two M2 (length 4 mm 0.157 in) pan head screws [stainless steel (SUS304)] are attached. 4.25 1.4 0.167 0.055 3.2 0.126 MS-EX10-12 Sensor mounting bracket (Optional) 8.1 t 1.2 Assembly dimensions 0.319 t 0.047 Mounting drawing with EX-11E� and EX-13E� (2.3) 8.1 6.25 t 1.2 (0.091) 0.319 0.246 t 0.047 4.5 (7.45) 6.25 20 0.177 (0.293) 0.246 0.787 1.4 3.2 0.055 (1.3) 0.126 (0.051) 4 0.25 10 1.4 0.157 1.25 0.010 0.394 0.055 8 15 11 0.049 3.2 0.315 0.591 0.433 0.126 2-M2�0.4 0.016 2.5 0.098 1.4 Beam- thru-hole threads 8 15 11 0.055 receiving 3.2 0.315 0.591 0.433 part 0.126 8 3.5 0.315 0.138 1.4 4.25 0.055 0.167 Material: Stainless steel (SUS304) 3.2 Two M2 (length 8 mm 0.315 in) pan head screws [stainless steel (SUS304)] are 0.126 8 attached. 3.5 0.315 0.138 20 0.787 243 Amplifier Built-in PHOTOELECTRIC SENSORS RX-LS200 RX EX-40 EQ-30 EQ-20 EX-10 EX-20 EX-30 CX-400 EX-10 DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ MS-EX10-13 Sensor mounting bracket (Optional) Assembly dimensions Mounting drawing with EX-14� 7 10.5 0.276 (2.75) 10.8 t 1.2 0.413 3.2 0.126 (0.108) 0.425 t 0.047 1.4 0.055 1.4 (0.7) 3.2 0.126 0.055 (0.028) 8 0.315 15 0.591 t 1.2 4-M2�0.4 0.016 t 0.047 thru-hole threads 13 1.75 3.5 0.512 0.069 10.8 0.138 10.5 6.5 0.256 5 6.25 0.425 0.413 0.197 0.246 7 1.25 0.276 0.049 1.4 3.2 0.055 11 2 0.126 Beam-emitting 0.433 0.079 part 3 0.118 11 15 8 Beam-receiving 0.433 0.591 0.315 part Material: Stainless steel (SUS304) Two M2 (length 4 mm 0.157 in) pan 1.4 4.25 head screws [stainless steel (SUS304)] 0.055 0.167 and two M2 (length 8 mm 0.315 in) pan head screws [stainless steel (SUS304)] 3.2 are attached. 0.126 244 RX-LS200 RX EX-40 EQ-30 EQ-20 EX-10 EX-20 EX-30 CX-400 PHOTOELECTRIC SENSORS Amplifier Built-in